wdiff rfc6765.original rfc6765.txt

Network Working Group
Internet Engineering Task Force (IETF) E. Beili
Internet-Draft
Request for Comments: 6765 Actelis Networks
Intended status:
Category: Standards Track M. Morgenstern
Expires: January 17, 2013
ISSN: 2070-1721 ECI Telecom
Jul 16, 2012
February 2013

xDSL multi-pair bonding Multi-Pair Bonding (G.Bond) MIB
draft-ietf-adslmib-gbond-mib-11.txt

Abstract

This document defines a Management Information Base (MIB) module for
use with network management protocols in TCP/IP-based internets.
This document defines an extension to the Interfaces Group MIB with a
set of common objects for managing multi-pair bonded Digital
Subscriber Line (xDSL) interfaces, as defined in ITU-T recommendations
Recommendations G.998.1, G.998.2 G.998.2, and G.998.3. The textual
conventions defining the bonding schemes are contained in a separate
MIB module maintained by Internet Assigned Number Numbers Authority (IANA) maintained MIB module. (IANA).
The MIB modules specific to each bonding technology are defined in
G9981-MIB, G9982-MIB G9982-MIB, and
G9983-MIB G9983-MIB, respectively.

Status of This Memo

This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents an Internet Standards Track document.

This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.

Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on January 17, 2013.
http://www.rfc-editor.org/info/rfc6765.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 ....................................................3
2. The Internet-Standard Management Framework . . . . . . . . . . 4 ......................4
3. The DSL Broadband Forum Management Framework for xDSL Bonding . . . . . 4 .......4
4. Relationship to Other MIB modules . . . . . . . . . . . . . . 4 Modules ...............................5
4.1. Relationship to Interfaces Group MIB module . . . . . . . 5 Module ................5
4.1.1. Layering Model . . . . . . . . . . . . . . . . . . . . 5 ......................................5
4.1.2. xDSL Bonding . . . . . . . . . . . . . . . . . . . . . 7 ........................................7
4.1.3. Discovery Operation . . . . . . . . . . . . . . . . . 7 .................................8
4.1.4. Initialization of G.Bond ports initialization . . . . . . . . . . . . . 10 Ports .....................10
4.1.5. Usage of the ifTable . . . . . . . . . . . . . . . . . . . 10 ...............................11
4.2. Relationship to G.Bond ATM, ETH ETH, and TDIM MIB modules . . . 11 Modules .....13
4.3. Relationship to xDSL MIB modules . . . . . . . . . . . . . 12 Modules ..........................13
4.4. Addition of new bonding schemes . . . . . . . . . . . . . 12 New Bonding Schemes ...........................13
5. MIB Structure . . . . . . . . . . . . . . . . . . . . . . . . 12 ..................................................13
5.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . 12 ..................................................13
5.2. Performance Monitoring . . . . . . . . . . . . . . . . . . 13 ....................................14
5.3. Mapping of DSL Broadband Forum TR-159 Managed Objects . . . . . . . 13 .........14
6. xDSL Multi-pair Multi-Pair Bonding MIB Definitions . . . . . . . . . . . 17 ........................19
7. IANA-maintained IANA-Maintained G.Bond TC Definitions . . . . . . . . . . . . 62 ..........................65
8. Security Considerations . . . . . . . . . . . . . . . . . . . 64 ........................................67
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 66 ............................................69
10. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 66 ...............................................69
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 67 ....................................................70
11.1. Normative References . . . . . . . . . . . . . . . . . . . 67 .....................................70
11.2. Informative References . . . . . . . . . . . . . . . . . . 68 ...................................71

1. Introduction

The

xDSL Multi-Pair Bonding, Multi-pair bonding allows a service provider to provide
high high-
bandwidth services to business and residential customers over
multiple xDSL lines, with greater speed and resiliency, resiliency than the service
over a single xDSL line, bridging the gap between xDSL and
fiber-based fiber-
based transport.

Currently

Currently, there are three xDSL Multi-Pair Bonding Multi-pair bonding schemes, also
known under the collective name G.Bond: "G.Bond":

o The ATM-Based Multi-Pair Bonding, Multi-pair bonding, as specified in ITU-T Recommendation
G.998.1
recommendation [G.998.1], which defines a method for the bonding (or
aggregating) of multiple xDSL lines (or individual bearer channels
in multiple xDSL lines) into a single bi-directional bidirectional logical link
carrying an ATM stream. This specification can be viewed as an
evolution of the legacy Inverse Multiplexing over for ATM (IMA)
technology [af-phy-0086], [AF-PHY-0086], applied to xDSL with variable rates on
each line/bearer channel.

o The Ethernet-Based Multi-Pair Bonding, Multi-pair bonding, as specified in ITU-T
Recommendation G.998.2
recommendation [G.998.2], which defines a method for the
bonding (or aggregating) of multiple xDSL lines (or individual
bearer channels in multiple xDSL lines) into a single bi-directional
bidirectional logical link carrying an Ethernet stream. This
specification can be viewed as IEEE 802.3-2005 [802.3] Clause 61 61,
Physical Medium Entity (PME) Aggregation, generalized to work over
any xDSL technology (2Base-TL and 10Pass-TS interfaces defined by
IEEE use G.SHDSL (Single-pair High-speed DSL) and VDSL technology (Very high
speed DSL) technology, respectively).

o The Multi-pair bonding using time-division inverse multiplexing Time-Division Inverse Multiplexing
(TDIM), specified in ITU-T Recommendation G.998.3 recommendation [G.998.3], which
defines a method for the bonding (or aggregating) of multiple xDSL
lines into a single bi-directional bidirectional logical link carrying a mix of
various traffic streams (e.g., Ethernet, ATM, TDM).

Architecturally

Architecturally, all three bonding schemes define a new "bonded"
Transport Protocol Specific - Transmission Convergence (TPS-TC) sub-
layer,
sub-layer, stacked above multiple ATM-TC, Ethernet/PTM-TC or STM-TC Ethernet/Packet Transfer
Mode-TC (PTM-TC), or Synchronous Transfer Mode-TC (STM-TC) (clear
channel) sub-layers for the ATM, Ethernet Ethernet, or TDIM bonding bonding,
respectively. Each underlying TPS-TC sub-layer represents a protocol
specific
protocol-specific interface to an xDSL line or an individual bearer
channel of an xDSL line. Bonding of multiple bearer channels in the
same xDSL line is not allowed.

All schemes allow bonding of up to 32 individual line/channel sub-
layers
sub-layers with variable rates, providing common functionality for
the configuration, initialization, operation operation, and monitoring of the
bonded link.

This document defines a MIB module common to all 3 schemes.
Additional managed objects, objects specific to each bonding technology, technology are
defined in the G9981-MIB [I-D.ietf-adslmib-gbond-atm-mib], [RFC6768], G9982-MIB
[I-D.ietf-adslmib-gbond-eth-mib] [RFC6767], and
G9983-MIB
[I-D.ietf-adslmib-gbond-tdim-mib] [RFC6766] modules.

The textual conventions listing the bonding schemes are defined in a
separate, IANA-maintained MIB module, the first version of which is
provided in this document. This arrangement would allow for future
bonding schemes to be easily supported, without the need to update
the common GBOND-MIB module, module.

2. The Internet-Standard Management Framework

For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].

Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This document specifies a
MIB module that is compliant to the SMIv2, which is described in STD
58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
2580 [RFC2580].

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14, RFC 2119 [RFC2119].

3. The DSL Broadband Forum Management Framework for xDSL Bonding

This document makes use of the DSL Broadband Forum technical report Management
"Management Framework for xDSL Bonding Bonding" [TR-159], defining a
management model and a hierarchy of management objects for the bonded
xDSL interfaces.

4. Relationship to Other MIB modules Modules

This section outlines the relationship of the MIB modules defined in
this document with other MIB modules described in the relevant RFCs.
Specifically, the following MIB modules are discussed: the Interfaces
Group MIB (IF-MIB), Inverse Stack Table MIB (IF-INVERTED-STACK-MIB) (IF-INVERTED-STACK-MIB),
and Interface Stack Capability MIB (IF-CAP-STACK-MIB), (IF-CAP-STACK-MIB); G.Bond scheme scheme-
specific modules: modules G.Bond/ATM (G9981-MIB), G.Bond/Ethernet (G9982-MIB) (G9982-MIB),
and G.Bond/TDIM (G9983-MIB), (G9983-MIB); and DSL specific DSL-specific MIB modules: modules ADSL
(ADSL-LINE-EXT-MIB), ADSL2 (ADSL2-LINE-MIB), SHDSL (HDSL2-SHDSL-LINE-
MIB),
(HDSL2-SHDSL-LINE-MIB), VDSL (VDSL-LINE-MIB) (VDSL-LINE-MIB), and VDSL2
(VDSL2-LINE-MIB).

4.1. Relationship to Interfaces Group MIB module Module

A bonded xDSL port is a stacked (a.k.a. aggregated or bonded)
interface and as such is managed using generic interface management
objects defined in the IF-MIB [RFC2863].

The stack management, i.e., actual connection of the sub-layers to
the top layer interface, is done via the ifStackTable, as defined in
the IF-MIB [RFC2863] and its inverse -- the ifInvStackTable, as
defined in the IF-INVERTED-STACK-MIB [RFC2864].

The ifCapStackTable and its inverse ifInvCapStackTable -- the ifInvCapStackTable, as
defined in the IF-CAP-STACK-MIB [RFC5066], [RFC5066] -- extend the stack
management with an ability to describe possible connections or cross-connect cross-
connect capability, when a flexible cross-connect matrix is present
between the interface layers.

4.1.1. Layering Model

A G.Bond interface can aggregate up to 32 channel sub-layers, with
each channel representing an xDSL line or an xDSL bearer channel.
For the purpose of brevity we will refer to the bonded interface as
the Generic Bonded Bonding Sub-layer (GBS) and to the channel sub-layer as
the Bonding Channel Entity (BCE).

A generic G.Bond device can have a number of GBS ports, each
connected to a particular upper layer (e.g., a Media Access Control
(MAC) interface for the G.998.2 scheme), while simultaneously cross-
connected to a number of underlying BCEs, with a single GBS per BCE single-GBS-per-BCE
relationship.

A GBS port is represented in the Interface Interfaces table (ifTable) as a
separate interface with an ifType reflecting a particular bonding
scheme, e.g., g9981(263), g9982(264) g9982(264), or g9983(265).

Each BCE in the aggregated GBS port is represented in the ifTable as
a separate interface with an ifType relevant to a particular xDSL
technology, e.g., shdsl(169) or vdsl(97). The ifType values are
defined in [IANAifType-MIB].

The following figure shows the layering diagram and corresponding use
of the ifTable for the bonded xDSL interfaces:

BCE - Bonding Channel Entity
GBS - Generic Bonded Bonding Sub-layer
PMD - Physical Medium Dependent
TPS-TC - Transport Protocol Specific - Transmission Convergence
PMS-TC - Physical Media Specific - Transmission Convergence

Figure 1: Use of ifTable for bonded Bonded xDSL interfaces Interfaces

The ifStackTable is indexed by the ifIndex values of the aggregated
G.Bond port (GBS) and the BCEs connected to it. The ifStackTable
allows a
Network Management network management application to determine which BCEs are
connected to a particular GBS and change connections (if supported by
the application). The ifInvStackTable, being an inverted version of
the ifStackTable, provides an efficient means for a Network Management network
management application to read a subset of the ifStackTable and
thereby determine which GBS runs on top of a particular BCE.

The ifCapStackTable ifCapStackTable, defined in the IF-CAP-STACK-MIB module,
specifies for each higher-layer interface (e.g., GBS port) a list of lower-
layer
lower-layer interfaces (e.g., BCEs), which can possibly be cross-connected cross-
connected to that higher-layer interface, determined by the cross-connect cross-
connect capability of the device. This table, modeled after the
ifStackTable, is read only, reflecting current cross-connect
capability of a stacked interface, which can be dynamic in some
implementations (e.g., if xDSL lines are located on a pluggable
module and the module is pulled out). Note that BCE availability per
GBS, described by the ifCapStackTable, can be constrained by other parameters,
parameters -- for example example, by the aggregation capacity of a GBS or by
the BCE in question being already connected to another GBS. So, in
order to ensure that a particular BCE can be connected to the GBS,
all respective parameters (e.g., ifCapStackTable, ifStackTable ifStackTable, and
gBondPortCapCapacity) SHALL be inspected.

The ifInvCapStackTable, also defined in the IF-CAP-STACK-MIB module,
describes which higher-layer interfaces (e.g., GBS ports) can
possibly be connected to a particular lower-layer interface (e.g.,
BCE), providing inverted mapping of the ifCapStackTable. While it
contains no additional information beyond that already contained in
the ifCapStackTable, the ifInvCapStackTable has the ifIndex values in
its INDEX clause in the reverse order, i.e., the lower-layer
interface first, and the higher-layer interface second, providing
efficient means for a Network Management network management application to read a subset
of the ifCapStackTable and thereby determine which interfaces can be
connected to run on top of a particular interface.

4.1.2. xDSL Bonding

The G.998.x Bonding allows a number of BCEs to be aggregated onto a
single logical GBS port, port by splitting the incoming traffic into
multiple streams, transmitting each stream over a specific BCE BCE, and
combining the streams at the remote GBS port, preserving the original
traffic order.

The Ethernet frames MAY be fragmented before the transmission and
reassembled at the remote end to minimize transportation delay. The
G.998.2 (G.Bond/Ethernet) ports with multiple BCEs MUST perform the
fragmentation and reassembly of the Ethernet frames. However However, for a
single-BCE G.998.2 ports this function MAY be omitted (a.k.a. bonding
bypass), to minimize fragmentation overhead and additional processing
delay as well as to be able to interoperate with non-G.998 DSL
equipment.

The agent is REQUIRED to indicate all supported bonding schemes (for
example
example, ATM, Ethernet Ethernet, and TDIM), including OPTIONAL support for the
bonding bypass in G.998.2 single-BCE ports.

The GBOND-MIB module allows a Network Management network management application to query
Bonding capability and enable/disable it if supported. Note that
enabling Bonding (by setting the value of the
gBondPortConfAdminScheme and gBondPortConfAdminScheme gBondPortConfPeerAdminScheme objects to
any supported bonding scheme other than 'none') effectively turns on
the fragmentation and re-assembly reassembly function, even on a single-BCE port.

4.1.3. Discovery Operation

The G.Bond ports may optionally support a discovery operation, operation whereby
BCEs, during initialization, exchange information about their
respective aggregation groups (GBS), via the [G.994.1] handshake
(G.hs) protocol. This information can then be used to detect copper
misconnections or for an automatic assignment of the local BCEs into
aggregation groups instead of a fixed pre-configuration. preconfiguration.

The MIB module defined in this document allow allows a Network Management network management
application to control the G.Bond discovery mechanism and query its
results.

Two tables are used by the G.Bond discovery mechanism: the
ifStackTable and the ifCapStackTable. The following pseudo-code pseudocode gives
an example of the discovery and automatic BCE assignment for a
generic multi-GBS G.Bond device, located at the Central Office (CO),
using objects defined in this MIB module, module as well as the
IF-CAP-STACK-MIB and IF-MIB modules [Note that automatic BCE
assignment is only shown here for the purposes of the example. Fixed
BCE pre-assignment, manual assignment assignment, or auto-
assignment auto-assignment using an
alternative internal algorithm may be chosen by a particular
implementation]:

// Go over all GBS ports in the CO device
FOREACH gbs[i] IN CO_device
{ // Perform discovery and auto-assignment on GBS ports
// with room for more Channels channels.
IF ( gbs[i].NumBCEs < gbs[i].BondCapacity )
{ // Assign a unique 6-octets 6-octet local discovery code to the GBS GBS,
// e.g., MAC address of the associated port or some other
// unique number specifically allocated for this purpose.
dc = gbs[i].DiscoveryCode = MAC[i];
// Go over all disconnected Channels, channels, which can
// potentially be connected to the GBS GBS.
FOREACH bce[j] IN ifCapStackTable[gbs[i]] AND
NOT IN ifStackTable[gbs[i]] // not connected
{ // Try to grab the remote RT_device, Remote Terminal device (RT) by writing the value
// value of the local 6 Byte 6-byte discovery code to the remote
// discovery code register (via a handshake mechanism).
// This operation is an atomic Set-if-Clear action, action; i.e., it
// would succeed only if the remote discovery register was
// zero. Read the remote discovery code register via a Get
// operation to see if the RT_device, RT, attached via the BCE BCE,
// is indeed marked as being the CO_device peer.
bce[j].RemoteDiscoveryCode = dc; // Set-if-Clear
r = bce[j].RemoteDiscoveryCode; // Get
IF ( r == dc AND gbs[i].NumBCEs < gbs[i].BondCapacity) gbs[i].BondCapacity )
{ // Remote RT_device RT connected via BCE[j] is/was a peer
// for GBS[i] GBS[i], and there is room for another BCE in the
// GBS[i] aggregation group (max. Bonding capacity is
// not reached yet).
// Connect this BCE to the GBS (via ifStackTable, the ifStackTable; the
// ifInvStackTable being ifInvStackTable, which is the inverse of ifStackTable is the ifStackTable,
// is updated automatically, automatically; i.e., gbs[i] is auto-added
// to ifInvStackTable[bce[j]]) ifInvStackTable[bce[j]]).
ADD bce[j] TO ifStackTable[gbs[i]];
gbs[i].NumBCEs = gbs[i].NumBCEs + 1;
// Discover all other disconnected BCEs, BCEs
// attached to the same RT_device RT and connect them to
// the GBS GBS, provided there is enough room for more BCEs.
FOREACH bce[k] IN ifCapStackTable[gbs[i]] and
NOT IN ifStackTable[gbs[i]]
{ // Get Remote Discovery Code the remote discovery code from the BCE to see if
// it belongs to a connected RT_device RT "grabbed" by
// the CO_device.
r = bce[k].RemoteDiscoveryCode;
IF ( r == dc AND gbs[i].NumBCEs < gbs[i].BondCapacity) gbs[i].BondCapacity )
{ // Physically connect the BCE to the GBS GBS.
// (gbs[i] is auto-added TO ifInvStackTable[bce[k]]) ifInvStackTable[bce[k]]).
ADD bce[k] TO ifStackTable[gbs[i]];
gbs[i].NumBCEs = gbs[i].NumBCEs + 1;
}
}
}
// At this point we have discovered all local BCEs which that
// are physically connected to the same remote RT_device
// RT and
// connected them to GBS[i]. Go to the next GBS.
BREAK;
}
}
}

An SNMP Agent agent for a G.Bond device builds the ifCapStackTable and its
inverse -- the ifInvCapStackTable -- on device initialization,
according to the cross-connect capabilities of the device.

Adding a BCE to the ifStackTable row for a specific GBS, GBS involves
actual connection of the BCE to the GBS.

Note that a GBS port does not have to be operationally 'down' for the
connection to succeed. In fact, a dynamic BCE addition (and removal)
MAY be implemented with an available BCE being initialized first (by
setting its ifAdminStatus to 'up') and then added to an operationally
'up' GBS port, by modifying a respective ifStackTable (and respective
ifInvStackTable) entry.

It is RECOMMENDED that a removal of the last operationally 'up' BCE
from an operationally 'up' GBS, i.e. i.e., modification of a respective
entry in ifStackTable the ifStackTable, and a corresponding entry in the
ifInvStackTable, would be rejected by the implementation (in the case
of SNMP SNMP, with the error inconsistentValue), as this action would
completely drop the link.

In addition to the standard handshake-based discovery described
above, [G.998.2] defines an optional frame-based discovery and pair
management. These frame-based methods are discussed in
[I-D.ietf-adslmib-gbond-eth-mib]. [RFC6767].

4.1.4. Initialization of G.Bond ports initialization Ports

G.Bond ports being built on top of xDSL technology, technology require a lengthy
initialization or 'training' process, process before any data can pass.
During this initialization initialization, both ends of a link (peers) work
cooperatively to achieve a required data rate on a particular copper
pair. Sometimes, when the copper line is too long or the noise on
the line is too high, that 'training' process may fail to achieve a
specific target rate with required characteristics.

The ifAdminStatus object from the IF-MIB, IF-MIB controls the desired state
of a GBS with all the BCEs connected to it or of an individual BCE
port. Setting this object to 'up' instructs a particular GBS or a
BCE to start the initialization process, which may take tens of
seconds for G.Bond ports. The ifOperStatus object from the IF-MIB
shows the operational state of an interface for the GBS, extended by
the gBondPortStatFltStatus object defined in this document, and a
corresponding *Status object from a relevant xDSL line MIB for BCE
interfaces.

A disconnected BCE may be initialized by changing the ifAdminState ifAdminStatus
from 'down' to 'up'. Changing the ifAdminState ifAdminStatus to 'up' on the GBS
initializes all BCEs connected to that particular GBS. Note that in
the case of bonding bonding, some interfaces may fail to initialize while
others succeed. The GBS is considered operationally 'up' if at least
one bonded BCE is operationally 'up'. When all BCEs connected to the
GBS are 'down' 'down', the GBS SHALL be considered operationally
'lowerLayerDown'. The GBS SHALL be considered operationally
'notPresent' if it is not connected to any BCE. The GBS/BCE
interface SHALL remain operationally 'down' during initialization,
indicated by the 'init' value of the gBondPortStatFltStatus object.

4.1.5. Usage of the ifTable

Both BCE and GBS interfaces are managed using interface specific interface-specific
management objects defined in the GBOND-MIB module and generic
interface objects from the ifTable of the IF-MIB, with all management
table entries referenced by the interface index ifIndex.

The following table summarizes G.Bond specific G.Bond-specific interpretations for
some of the ifTable objects specified by the mandatory
ifGeneralInformationGroup:

+---------------+---------------------------------------------------+
| IF-MIB object Object | G.Bond interpretation Interpretation |
+---------------+---------------------------------------------------+
| ifIndex | Interface index. Note that each BCE and each GBS |
| | in the G.Bond PHY MUST have a unique index, as |
| | there are some GBS GBS- and BCE specific BCE-specific attributes |
| | accessible only on the GBS or BCE level. |
+---------------+---------------------------------------------------+
| ifType | g9981(263), g9982(264) g9982(264), or g9983(265) for the ATM, |
| | Ethernet ATM, Ethernet, or TDIM GBS respectively, shdsl(169) for GBS, respectively; |
| | shdsl(169) for the G.SHDSL BCE, vdsl(97) for the |
| | VDSL BCE, etc. |
+---------------+---------------------------------------------------+
| ifSpeed | Operating data rate for the BCE. For the GBS GBS, it |
| | is the sum of the current operating data rates of |
| | all BCEs in the aggregation group, without the |
| | encapsulation overhead and G.Bond overhead, but |
| | accounting for the Inter-Frame Gaps (IFG). When a |
| | GBS or a BCE is operating in an asymetrical asymmetrical |
| | fashion (upstream (the upstream data rate differs from the |
| | downstream one) one), the lowest of the values is |
| | shown. |
+---------------+---------------------------------------------------+
| ifAdminStatus | Setting this object to 'up' instructs a |
| | particular GBS (with all BCEs connected to it) or |
| | a BCE to start the initialization process process. |
+---------------+---------------------------------------------------+
| ifOperStatus | A relevant *Status object from a particular line |
| | MIB supplements the value of ifOperStatus for |
| | BCEs. gBondPortStatFltStatus supplements the |
| | value of ifOperStatus for a GBS. Note that both |
| | relevant objects shall be inspected to determine |
| | the real operational status of a BCE/GBS port, |
| | e.g. e.g., a GBS port may be operationally 'up' with |
| | gBondPortStatFltStatus indicating lowRate(4) |
| | fault condition, or 'down' with no gBond faults. |
+---------------+---------------------------------------------------+

Table 1: G.Bond interpretation Interpretation of IF-MIB objects Objects

4.2. Relationship to G.Bond ATM, ETH ETH, and TDIM MIB modules Modules

The MIB module defined in this document is common to all G.998
bonding schemes. It MUST be used in conjunction with a bonding
scheme-specific MIB module:

o G9981-MIB [I-D.ietf-adslmib-gbond-atm-mib] [RFC6768] for a G.998.1 bonded interface.

o G9982-MIB [I-D.ietf-adslmib-gbond-eth-mib] [RFC6767] for a G.998.2 bonded interface.

o G9983-MIB [I-D.ietf-adslmib-gbond-tdim-mib] [RFC6766] for a G.998.3 bonded interface.

4.3. Relationship to xDSL MIB modules Modules

Each xDSL technology is described in a relevant xDSL line MIB module:
e.g., the HDSL2-SHDSL-LINE-MIB [RFC4319] for G.SHDSL,
ADSL-LINE-EXT-MIB [RFC3440] for ADSL, ADSL2-LINE-MIB [RFC4706] for
ADSL2, VDSL-LINE-MIB [RFC3728] for VDSL VDSL, or VDSL2-LINE-MIB [RFC5650]
for VDSL2.

These MIB moduless modules are used to manage individual xDSL lines/channels
(BCEs).

4.4. Addition of new bonding schemes New Bonding Schemes

In case a new bonding scheme is introduced in a revision of G.998,
IANA can update the IANA-maintained MIB module, adding the
corresponding new value, value to the IANAgBondScheme and
IANAgBondSchemeList textual conventions, as well as listing the new
scheme-specific MIB module's name (e.g. (e.g., G998x-MIB).

Any scheme-specific aspect of an existing GBOND-MIB object SHALL be
described in the corresponding G998x-MIB module, to prevent an
unnesessary re-issue
unnecessary reissue of the GBOND-MIB module. For example, an exact
definition of an Errored Second (ES) or a Severely Errored Second
(SES) can be bonding-scheme specific, specific; see the definition definitions for the
gBondPortPmCurES and gBondPortPmCurSES objects.

5. MIB Structure

5.1. Overview

The main management objects defined in the GBOND-MIB module are split
into 2 groups, structured as recommended by RFC 4181 [RFC4181]:

o gBondPort - containing objects for configuration, capabilities,
status, historical performance monitoring Performance Monitoring, and notifications,
common to all G.Bond ports (GBS).

o gBondBce - containing a single common object for configuration of
the remote discovery code per BCE. Note that the rest of the
objects for BCE configuration, capabilities, status status, and
notifications, is
notifications are located in relevant xDSL line MIB modules as
well as in the bonding scheme specific scheme-specific MIB modules.

5.2. Performance Monitoring

The OPTIONAL performance monitoring Performance Monitoring counters, thresholds thresholds, and history
buckets (interval-counters) defined in [TR-159] are implemented using
the textual conventions defined in the HC-PerfHist-TC-MIB [RFC3705].
The HC-PerfHist-TC-MIB defines 64-bit versions of the textual
conventions found in the PerfHist-TC-MIB [RFC3593].

The agent SHOULD align the beginning of each interval to a fifteen fifteen-
minute boundary of a wall clock. Likewise, the beginning of each one
day intervals
one-day interval SHOULD be aligned with the start of a day.

The rationale behind it this is to simplify collection and analysis of the
PM
Performance Monitoring (PM) from multiple agents by a network
management system (NMS) - -- each PM interval can be "time-stamped"
using the gBond*IntervalIndex object, from the fact that the 1-day
interval starts at 00:00 and 15-min the 15-minute intervals are aligned with
each 1/4 hour and the network-wide "wall clock", typically
distributed via NTP or SNTP the Simple Network Time Protocol (SNTP)
[RFC5905]. If the agent does not have an access to the wall clock, a
local clock can be used. In this case, as well as when coping with
multiple time zones, the NMS would have to correlate for the difference
between the agent's local clock (available (available, for example example, via the
hrSystemDate object from the HOST-RESOURCES-MIB [RFC2790]) and the
wall clock.

Counters are not reset when a GBS is reinitialized, re-initialized, but rather only
when the agent is reset or reinitialized. re-initialized.

Note that the accumulation of certain performance events for a
monitored entity is inhibited (counting stops) during periods of
service unavailability on that monitored entity. The DESCRIPTION
clause of performance monitoring Performance Monitoring counters in this MIB module
specifies which of the counters are inhibited during periods of
service unavailability.

5.3. Mapping of DSL Broadband Forum TR-159 Managed Objects

This section contains the mapping between relevant managed objects
(attributes) defined in [TR-159] and managed objects defined in this
document and in associated MIB modules, i.e., the IF-MIB [RFC2863].

+-------------------------------+-----------------------------------+

+--------------------------------+------------------------------------+
| G.Bond Managed Object | Corresponding SNMP Object |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| oBondingGroup - Basic Package | |
| (Mandatory) | |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupID | ifIndex (IF-MIB) |
+-------------------------------+-----------------------------------+
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupBondSchemesSupported | gBondPortCapSchemesSupported |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPeerBondSchemesSupporte aGroupPeerBondSchemesSupported | gBondPortCapPeerSchemesSupported |
| d | |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupAdminBondScheme | gBondPortConfAdminScheme |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPeerAdminBondScheme | gBondPortConfPeerAdminScheme |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupOperBondScheme | gBondPortStatOperScheme |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPeerOperBondScheme | gBondPortStatPeerOperScheme |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupEnd | gBondPortStatSide |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupOperState | ifOperStatus (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupAdminState | ifAdminStatus (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupStatus | gBondPortStatFltStatus |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupCapacity | gBondPortCapCapacity |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPeerCapacity | gBondPortCapPeerCapacity |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupNumChannels | gBondPortStatNumBCEs |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupName | ifName (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupDiscoveryCode | gBondPortConfDiscoveryCode |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupUpRate | gBondPortStatUpDataRate |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupDownRate | gBondPortStatDnDataRate |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupTargetUpRate | gBondPortConfTargetUpDataRate |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupTargetDownRate | gBondPortConfTargetDnDataRate |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupThreshLowUpRate | gBondPortConfThreshLowUpRate |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
+--------------------------------+------------------------------------+
| aGroupThreshLowDownRate | gBondPortConfThreshLowDnRate |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupLowRateCrossingEnable | gBondPortConfLowRateCrossingEnabl |
| | e gBondPortConfLowRateCrossingEnable |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nGroupLowUpRateCrossing | gBondLowUpRateCrossing |
+--------------------------------+------------------------------------+
| nGroupLowDownRateCrossing | gBondLowDnRateCrossing |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupLinkUpDownEnable | ifLinkUpDownTrapEnable (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nGroupLinkUp | linkDown linkUp (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nGroupLinkDown | linkUp linkDown (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| oBondingGroup - PM Package | |
| (Optional) | |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfES | gBondPortPmCurES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfSES | gBondPortPmCurSES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfUAS | gBondPortPmCurUAS |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf15MinValidIntervals | gBondPortPmCur15MinValidIntervals |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf15MinInvalidInterva aGroupPerf15MinInvalidIntervals| gBondPortPmCur15MinInvalidIntervals|
+--------------------------------+------------------------------------+
| gBondPortPmCur15MinInvalidInterva |
| ls | ls |
+-------------------------------+-----------------------------------+
| aGroupPerfCurr15MinTimeElapse aGroupPerfCurr15MinTimeElapsed | gBondPortPmCur15MinTimeElapsed |
| d | |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfCurr15MinES | gBondPortPmCur15MinES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfCurr15MinSES | gBondPortPmCur15MinSES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfCurr15MinUAS | gBondPortPmCur15MinUAS |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfTcaEnable | gBondPortConfPmTcaEnable |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfThreshold15MinES | gBondPortPmTcaProfileThresh15MinE |
| | S gBondPortPmTcaProfileThresh15MinES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfThreshold15MinSES | gBondPortPmTcaProfileThresh15MinS |
| | ES |
+-------------------------------+-----------------------------------+ gBondPortPmTcaProfileThresh15MinSES|
+--------------------------------+------------------------------------+
| aGroupPerfThreshold15MinUAS | gBondPortPmTcaProfileThresh15MinU |
| | AS |
+-------------------------------+-----------------------------------+ gBondPortPmTcaProfileThresh15MinUAS|
+--------------------------------+------------------------------------+
| nGroupPerfTca15MinES | gBondPmTca15MinESCrossing |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nGroupPerfTca15MinSES | gBondPmTca15MinSESCrossing |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
+--------------------------------+------------------------------------+
| nGroupPerfTca15MinUAS | gBondPmTca15MinUASCrossing |
+-------------------------------+-----------------------------------+
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf1DayValidIntervals | gBondPortPmCur1DayValidIntervals |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf1DayInvalidInterval aGroupPerf1DayInvalidIntervals | gBondPortPmCur1DayInvalidInterval |
| s | s gBondPortPmCur1DayInvalidIntervals |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfCurr1DayTimeElapsed | gBondPortPmCur1DayTimeElapsed |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfCurr1DayES | gBondPortPmCur1DayIntervalES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfCurr1DaySES | gBondPortPmCur1DayIntervalSES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfCurr1DayUAS | gBondPortPmCur1DayIntervalUAS |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfThreshold1DayES | gBondPortPmTcaProfileThresh1DayES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfThreshold1DaySES | gBondPortPmTcaProfileThresh1DaySE |
| | S gBondPortPmTcaProfileThresh1DaySES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerfThreshold1DayUAS | gBondPortPmTcaProfileThresh1DayUA |
| | S gBondPortPmTcaProfileThresh1DayUAS |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nGroupPerfTca1DayES | gBondPmTca1DayESCrossing |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nGroupPerfTca1DaySES | gBondPmTca1DaySESCrossing |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nGroupPerfTca1DayUAS | gBondPmTca1DayUASCrossing |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf15MinIntervalNumber | gBondPortPm15MinIntervalIndex |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf15MinIntervalValid | gBondPortPm15MinIntervalValid |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf15MinIntervalES | gBondPortPm15MinIntervalES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf15MinIntervalSES | gBondPortPm15MinIntervalSES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf15MinIntervalUAS | gBondPortPm15MinIntervalUAS |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf1DayIntervalNumber | gBondPortPm1DayIntervalIndex |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf1DayIntervalValid | gBondPortPm1DayIntervalValid |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf1DayIntervalMoniSec aGroupPerf1DayIntervalMoniSecs | gBondPortPm1DayIntervalMoniTime |
| s | |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf1DayIntervalES | gBondPortPm1DayIntervalES |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf1DayIntervalSES | gBondPortPm1DayIntervalSES |
+--------------------------------+------------------------------------+
+--------------------------------+------------------------------------+
| aGroupPerf1DayIntervalUAS | gBondPortPm1DayIntervalUAS |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| oLine - Basic Package | |
| (Mandatory) | |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aLineID | ifIndex (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aLineType | ifType (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aLineOperState | ifOperStatus (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aLineStatus | *dsl*CurrStatus (*DSL-LINE-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aLineEnd | *dsl*Side (*DSL-LINE-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aLineAdminState | ifAdminStatus (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aLineRemoteDiscoveryCode | gBondBceConfRemoteDiscoveryCode |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aLineUpDownEnable | ifLinkUpDownTrapEnable (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nLineUp | linkUp LinkUp (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| nLineDown | linkDown LinkDown (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| oChannel - Basic Package | |
| (Mandatory) | |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aChannelID | ifIndex (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aChannelGroupID | |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aChannelType | ifType (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aChannelOperState | ifOperStatus (IF-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+
| aChannelStatus | *dsl*CurrStatus (*DSL-LINE-MIB), |
| | xdsl2ChStatus*Status |
| | (VDSL2-LINE-MIB) |
+-------------------------------+-----------------------------------+
+--------------------------------+------------------------------------+

Table 2: Mapping of TR-159 Managed Objects

6. xDSL Multi-pair Multi-Pair Bonding MIB Definitions

The GBOND-MIB module IMPORTS objects from SNMPv2-SMI [RFC2578],
SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580], SNMP-FRAMEWORK-MIB
[RFC3411], IF-MIB [RFC2863], and HC-PerfHist-TC-MIB [RFC3705].
The module has been structured as recommended by [RFC4181].

GBOND-MIB DEFINITIONS ::= BEGIN

IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
NOTIFICATION-TYPE,
mib-2,
Unsigned32,
Gauge32
FROM SNMPv2-SMI -- [RFC2578] RFC 2578
TEXTUAL-CONVENTION,
TruthValue,
RowStatus,
PhysAddress
FROM SNMPv2-TC -- [RFC2579] RFC 2579
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580] RFC 2580
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- [RFC3411] RFC 3411
ifIndex
FROM IF-MIB -- [RFC2863] RFC 2863
HCPerfCurrentCount,
HCPerfIntervalCount,
HCPerfIntervalThreshold,
HCPerfValidIntervals,
HCPerfInvalidIntervals,
HCPerfTimeElapsed,
HCPerfTotalCount
FROM HC-PerfHist-TC-MIB -- [RFC3705] RFC 3705
IANAgBondScheme,
IANAgBondSchemeList
FROM IANA-GBOND-TC-MIB
;
------------------------------------------------------------------------
gBondMIB MODULE-IDENTITY
LAST-UPDATED "201207160000Z" "201302200000Z" -- Jul 16, 2012 20 February 2013
ORGANIZATION "IETF ADSL MIB Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/adslmib-charter.html
http://datatracker.ietf.org/wg/adslmib/charter/

Mailing Lists:
General Discussion: adslmib@ietf.org
To Subscribe: adslmib-request@ietf.org
In Body: subscribe your_email_address

Chair: Menachem Dodge
Postal: ECI Telecom, Ltd.
30 Hasivim St., St.
Petach-Tikva 4951169
Israel
Phone: +972-3-926-8421
EMail: menachem.dodge@ecitele.com menachemdodge1@gmail.com

Editor: Edward Beili
Postal: Actelis Networks, Inc.
25 Bazel St., P.O.B. 10173
Petach-Tikva 49103
Israel
Phone: +972-3-924-3491
EMail: edward.beili@actelis.com

Editor: Moti Morgenstern
Postal: ECI Telecom
30 Hasivim St.
Petach-Tikva 4951169
Israel
Phone: +972-3-926-6258
EMail: moti.morgenstern@ecitele.com"

DESCRIPTION
"The objects in this MIB module are used to manage the
multi-pair bonded xDSL Interfaces, interfaces, as defined in ITU-T
recommendations
Recommendations G.998.1, G.998.2 G.998.2, and G.998.3.

This MIB module MUST be used in conjunction with a bonding
scheme specific
scheme-specific MIB module, that is, G9981-MIB, G9982-MIB G9982-MIB,
or G9983-MIB.

The following references are used throughout this MIB module:

[G.998.1] refers to:
ITU-T Recommendation G.998.1: 'ATM-based multi-pair bonding',
January 2005.

[G.998.2] refers to:
ITU-T Recommendation G.998.2: 'Ethernet-based multi-pair
bonding', January 2005.

[G.998.3] refers to:
ITU-T Recommendation G.998.3: 'Multi-pair bonding using
time-division inverse multiplexing', January 2005.

[TR-159] refers to:
Broadband Forum Technical Report: 'Management Framework for
xDSL Bonding', December 2008.

Naming Conventions:
BCE - Bonding Channel Entity
BTU - Bonding Transmission Terminating Unit
BTU-C - Bonding Transmission Terminating Unit, CO side
BTU-R - Bonding Transmission Terminating Unit, Remote Terminal (CPE) side
CO - Central Office
CPE - Customer Premises Equipment
GBS - Generic Bonding Sublayer Sub-layer
PM - Performance Monitoring
SNR - Signal to Noise Ratio
TCA - Threshold Crossing Alert

Copyright (C) The (c) 2013 IETF Trust (2012).
This version and the persons identified as
authors of this MIB module the code. All rights reserved.

Redistribution and use in source and binary forms, with or without
modification, is part permitted pursuant to, and subject to the license
terms contained in, the Simplified BSD License set forth in Section
4.c of RFC XXXX;
see the RFC itself for full legal notices." IETF Trust's Legal Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info)."

REVISION "201207160000Z" "201302200000Z" -- Jul 16, 2012 20 February 2013
DESCRIPTION "Initial version, published as RFC XXXX."

-- EdNote: Replace XXXX with the actual RFC number &
-- remove this note 6765."

::= { mib-2 ZZZ 211 }

-- EdNote: Replace ZZZ with a real OID once it is
-- allocated & remove this note.

-- Sections of the module
-- Structured as recommended by [RFC4181], RFC 4181, Appendix D
gBondObjects OBJECT IDENTIFIER ::= { gBondMIB 1 }

gBondConformance OBJECT IDENTIFIER ::= { gBondMIB 2 }

-- Groups in the module

gBondPort OBJECT IDENTIFIER ::= { gBondObjects 1 }

gBondBce OBJECT IDENTIFIER ::= { gBondObjects 2 }

-- Textual Conventions

GBondPm1DayIntervalThreshold ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"This textual convention defines a range of values that may be
set in a fault threshold alarm control for a 1-day performance
monitoring Performance
Monitoring interval.
As the number of seconds in a 1-day interval numbers at most
86400, objects of this type may have a range of 0...86400,
where the value of 0 disables the alarm."
SYNTAX Unsigned32 (0..86400)

-- Port Notifications Group group

gBondPortNotifications OBJECT IDENTIFIER ::= { gBondPort 0 }

gBondLowUpRateCrossing NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here here, since we are under specific GBS
gBondPortStatUpDataRate,
gBondPortConfThreshLowUpRate
}
STATUS current
DESCRIPTION
"This notification indicates that the G.Bond port's upstream
data rate has reached/dropped below or exceeded the low
upstream rate threshold, specified by
gBondPortConfThreshLowUpRate.

This notification MAY be sent for the -O subtype ports
while the port is up, 'up', on the crossing event in both
directions: from normal (rate is above the threshold) to low
(rate equals the threshold or is below it) and from low to
normal. This notification is not applicable to the -R
subtypes.

It is RECOMMENDED that a small debouncing period of 2.5 sec,
between the detection of the condition and notification,
is
be implemented to prevent simultaneous LinkUp/LinkDown and
gBondLowUpRateCrossing notifications to be from being sent.

The adaptive nature of the G.Bond technology allows the port
to adapt itself to the changes in the copper environment, environment;
e.g., an impulse noise, alien crosstalk, or a
micro-interruption may temporarily drop one or more BCEs in
the aggregation group, causing a rate degradation of the
aggregated G.Bond link. The dropped BCEs would then try to
re-initialize, possibly at a lower rate than before, adjusting
the rate to provide the required target SNR margin.

Generation of this notification is controlled by the
gBondPortConfLowRateCrossingEnable object.

This object maps to the TR-159 notification
nGroupLowUpRateCrossing."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.24"
::= { gBondPortNotifications 1 }

gBondLowDnRateCrossing NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here here, since we are under specific GBS
gBondPortStatDnDataRate,
gBondPortConfThreshLowDnRate
}
STATUS current
DESCRIPTION
"This notification indicates that the G.Bond port's downstream
data rate has reached/dropped below or exceeded the low
downstream rate threshold, specified by
gBondPortConfThreshLowDnRate.

It is RECOMMENDED that a small debouncing period of 2.5 sec,
between the detection of the condition and notification,
is
be implemented to prevent simultaneous LinkUp/LinkDown and
gBondLowDnRateCrossing notifications to be from being sent.

The adaptive nature of the G.Bond technology allows the port
to adapt itself to the changes in the copper environment, environment;
e.g., an impulse noise, alien crosstalk, or a
micro-interruption may temporarily drop one or more BCEs in
the aggregation group, causing a rate degradation of the
aggregated G.Bond link. The dropped BCEs would then try to
re-initialize, possibly at a lower rate than before,
adjusting the rate to provide the required target SNR margin.

Generation of this notification is controlled by the
gBondPortConfLowRateCrossingEnable object.

This object maps to the TR-159 notification
nGroupLowDownRateCrossing."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.25"
::= { gBondPortNotifications 2}

gBondPmTca15MinESCrossing NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here here, since we are under specific GBS
gBondPortPmCur15MinES,
gBondPortPmTcaProfileThresh15MinES
}
STATUS current
DESCRIPTION
"This notification indicates that the Errored Seconds threshold,
specified by gBondPortPmTcaProfileThresh15MinES, has been
reached or exceeded for the GPS GBS port.

Generation of this notification is controlled by the
gBondPortConfPmTcaEnable and
gBondPortPmTcaProfileThresh15MinES objects.

This object maps to the TR-159 notification
nGroupPerfTca15MinES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.42"
::= { gBondPortNotifications 3}

gBondPmTca15MinSESCrossing NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here here, since we are under specific GBS
gBondPortPmCur15MinSES,
gBondPortPmTcaProfileThresh15MinSES
}
STATUS current
DESCRIPTION
"This notification indicates that the Severely Errored Seconds
threshold, specified by gBondPortPmTcaProfileThresh15MinSES,
has been reached or exceeded for the GPS GBS port.

Generation of this notification is controlled by the
gBondPortConfPmTcaEnable and
gBondPortPmTcaProfileThresh15MinSES objects.

This object maps to the TR-159 notification
nGroupPerfTca15MinSES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.43"
::= { gBondPortNotifications 4}

gBondPmTca15MinUASCrossing NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here here, since we are under specific GBS
gBondPortPmCur15MinUAS,
gBondPortPmTcaProfileThresh15MinUAS
}
STATUS current
DESCRIPTION
"This notification indicates that the Unavailable Seconds
threshold, specified by gBondPortPmTcaProfileThresh15MinES, gBondPortPmTcaProfileThresh15MinUAS,
has been reached or exceeded for the GPS GBS port.

Generation of this notification is controlled by the
gBondPortConfPmTcaEnable and
gBondPortPmTcaProfileThresh15MinUAS objects.

This object maps to the TR-159 notification
nGroupPerfTca15MinUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.44"
::= { gBondPortNotifications 5}

gBondPmTca1DayESCrossing NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here here, since we are under specific GBS
gBondPortPmCur1DayES,
gBondPortPmTcaProfileThresh1DayES
}
STATUS current
DESCRIPTION
"This notification indicates that the Errored Seconds threshold,
specified by gBondPortPmTcaProfileThresh1DayES, has been
reached or exceeded for the GPS GBS port.

Generation of this notification is controlled by the
gBondPortConfPmTcaEnable and
gBondPortPmTcaProfileThresh1DayES objects.

This object maps to the TR-159 notification
nGroupPerfTca1DayES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.54"
::= { gBondPortNotifications 6}

gBondPmTca1DaySESCrossing NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here here, since we are under specific GBS
gBondPortPmCur1DaySES,
gBondPortPmTcaProfileThresh1DaySES
}
STATUS current
DESCRIPTION
"This notification indicates that the Severely Errored Seconds
threshold, specified by gBondPortPmTcaProfileThresh1DaySES,
has been reached or exceeded for the GPS GBS port.

Generation of this notification is controlled by the
gBondPortConfPmTcaEnable and
gBondPortPmTcaProfileThresh1DaySES objects.

This object maps to the TR-159 notification
nGroupPerfTca1DaySES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.55"
::= { gBondPortNotifications 7}

gBondPmTca1DayUASCrossing NOTIFICATION-TYPE
OBJECTS {
-- ifIndex is not needed here here, since we are under specific GBS
gBondPortPmCur1DayUAS,
gBondPortPmTcaProfileThresh1DayUAS
}
STATUS current
DESCRIPTION
"This notification indicates that the Unavailable Seconds
threshold, specified by gBondPortPmTcaProfileThresh1DayUAS,
has been reached or exceeded for the GPS GBS port.

Generation of this notification is controlled by the
gBondPortConfPmTcaEnable and
gBondPortPmTcaProfileThresh1DayUAS objects.

This object maps to the TR-159 notification
nGroupPerfTca1DayUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.56"
::= { gBondPortNotifications 8}

-- G.Bond Port (GBS) group

gBondPortConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF GBondPortConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for configuration of G.Bond GBS ports. Entries in this
table MUST be maintained in a persistent manner" manner."
::= { gBondPort 1 }

gBondPortConfEntry OBJECT-TYPE
SYNTAX GBondPortConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the G.Bond Port Configuration table.
Each entry represents a G.Bond port indexed by the ifIndex.
Note that a G.Bond GBS port runs on top of a single
or multiple BCE port(s), which are also indexed by the ifIndex."
INDEX { ifIndex }
::= { gBondPortConfTable 1 }

GBondPortConfEntry ::=
SEQUENCE {
gBondPortConfAdminScheme IANAgBondScheme,
gBondPortConfPeerAdminScheme IANAgBondScheme,
gBondPortConfDiscoveryCode PhysAddress,
gBondPortConfTargetUpDataRate Unsigned32,
gBondPortConfTargetDnDataRate Unsigned32,
gBondPortConfThreshLowUpRate Unsigned32,
gBondPortConfThreshLowDnRate Unsigned32,
gBondPortConfLowRateCrossingEnable TruthValue,
gBondPortConfPmTcaConfProfile SnmpAdminString,
gBondPortConfPmTcaEnable TruthValue
}

gBondPortConfAdminScheme OBJECT-TYPE
SYNTAX IANAgBondScheme
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A desired bonding scheme for a G.Bond GBS port.
The following values instruct the port to use the corresponding
bonding scheme if supported:
none(0) - instructs the port not to use bonding
(only on a single-BCE G.998.2 GBS)
g9981(1) - instructs the port to use G.998.1 bonding
g9982(2) - instructs the port to use G.998.2 bonding
g9983(3) - instructs the port to use G.998.3 bonding

Changing of the gBondPortConfAdminScheme object MUST be
performed when the link is administratively 'down', as indicated
by the ifAdminStatus object in the IF-MIB.
Attempts to change this object MUST be rejected (in the case of SNMP
SNMP, with the error inconsistentValue), if the link is Up 'up' or
Initializing.
initializing. Attempts to change this object to an unsupported
bonding scheme (see gBondPortCapSchemesSupported) SHALL be
rejected (in the case of SNMP SNMP, with the error wrongValue).
Setting this object to the value of 'none' must be rejected for
GBS ports with multiple BCEs (with the error inconsistentValue).

This object maps to the TR-159 attribute aGroupAdminBondScheme."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.6; RFC 2863, IF-MIB, ifAdminStatus"
::= { gBondPortConfEntry 1 }

gBondPortConfPeerAdminScheme OBJECT-TYPE
SYNTAX IANAgBondScheme
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A desired bonding scheme for a peer (link partner) G.Bond
port (GBS).
The following values instruct the peer port to use the
corresponding bonding scheme if supported:
none(0) - instructs the port not to use bonding
(only on a single-BCE G.998.2 GBS)
g9981(1) - instructs the port to use G.998.1 bonding
g9982(2) - instructs the port to use G.998.2 bonding
g9983(3) - instructs the port to use G.998.3 bonding

Changing of this object MUST be performed when the link is
administratively 'down', as indicated by the ifAdminStatus
object in the IF-MIB.
Attempts to change this object MUST be rejected (in the case of SNMP
SNMP, with the error inconsistentValue), if the link is Up 'up' or
Initializing.
initializing. Attempts to change this object to an unsupported
bonding scheme (see gBondPortCapPeerSchemesSupported) SHALL be
rejected (in the case of SNMP SNMP, with the error wrongValue).
Setting this object to the value of 'none' must be rejected for
GBS ports with multiple BCEs (with the error inconsistentValue).

This object maps to the TR-159 attribute
aGroupPeerAdminBondScheme."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.7; RFC 2863, IF-MIB, ifAdminStatus"
::= { gBondPortConfEntry 2 }

gBondPortConfDiscoveryCode OBJECT-TYPE
SYNTAX PhysAddress (SIZE(6)) (SIZE (6))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A Discovery Code discovery code of the G.Bond port (GBS).
A unique 6 octet long 6-octet-long code used by the Discovery function.
This object MUST be instantiated for the -O subtype GBS before
writing
write operations on the gBondBceConfRemoteDiscoveryCode
(Set_if_Clear and Clear_if_Same) are performed by BCEs
associated with the GBS.
The initial value of this object for -R subtype ports after
reset is all zeroes. For -R subtype ports, the value of this
object cannot be changed directly. This value may be changed
as a result of writing a write operation on the
gBondBceConfRemoteDiscoveryCode object of a remote BCE of -O
subtype, connected to one of the local BCEs associated with
the GBS.

Discovery MUST be performed when the link is administratively
'down', as indicated by the ifAdminStatus object in the IF-MIB.
Attempts to change this object MUST be rejected (in the case of
SNMP
SNMP, with the error inconsistentValue), if the link is Up 'up' or
Initializing.
initializing.

This object maps to the TR-159 attribute
aGroupDiscoveryCode."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.20; [802.3] [802.3], Sections 61.2.2.8.3,
61.2.2.8.4, 45.2.6.6.1, 45.2.6.8, 61A.2;
RFC 2863, IF-MIB, ifAdminStatus"
::= { gBondPortConfEntry 3 }

gBondPortConfTargetUpDataRate OBJECT-TYPE
SYNTAX Unsigned32(0|1..10000000) Unsigned32 (0|1..10000000)
UNITS "Kbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A desired G.Bond port Data Rate data rate in the upstream direction,
in Kbps, to be achieved during initialization, under
restrictions placed upon the member BCEs by their respective
configuration settings.
This object represents a sum of individual BCE upstream data
rates, modified to compensate for fragmentation and
encapsulation overhead (e.g., for an Ethernet service, the
target data rate of 10Mbps 10 Mbps SHALL allow lossless transmission
of full-duplex 10Mbps 10-Mbps Ethernet frame stream with minimal
inter-frame gap).
Note that the target upstream data rate may not be achieved
during initialization (e.g., due to unavailability of required
BCEs) or the initial bandwidth could deteriorate, so that the
actual upstream data rate (gBondPortStatUpDataRate) could be less
than gBondPortConfTargetUpDataRate.

The value is limited above by 10 Gbps, to accommodate very
high speed bonded xDSL interfaces (e.g. (e.g., 32 x 100Mbps). 100 Mbps).

The value between 1 and 10000000 indicates that the total
upstream data rate of the G.Bond port after initialization
SHALL be equal to the target data rate or less, if the target
upstream data rate cannot be achieved under the restrictions
configured for BCEs. In case cases where the copper environment
allows to
achieve a higher upstream data rate to be achieved than that
specified by this object, the excess capability SHALL be
either converted to an additional SNR margin or reclaimed by
minimizing transmit power.

The value of 0 means that the target data rate is not
fixed and SHALL be set to the maximum attainable rate during
initialization (Best Effort), (best effort), under specified spectral
restrictions and with a desired SNR Margin margin per BCE.

This object is read-write for the -O subtype G.Bond ports.
It is irrelevant for the -R subtypes - -- attempts to read or
change this object for such ports MUST be rejected (in the case
of
SNMP SNMP, with the error inconsistentValue).

Changing of the Target Upstream Data Rate target upstream data rate MUST be performed
when the link is administratively 'down', as indicated by the
ifAdminStatus object in the IF-MIB.
Attempts to change this object MUST be rejected (in the case of SNMP
SNMP, with the error inconsistentValue), if the link is Up 'up' or
Initializing.
initializing.

This object maps to the TR-159 attribute aGroupTargetUpRate."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.17; RFC 2863, IF-MIB, ifAdminStatus"
::= { gBondPortConfEntry 4 }

gBondPortConfTargetDnDataRate OBJECT-TYPE
SYNTAX Unsigned32(0|1..10000000) Unsigned32 (0|1..10000000)
UNITS "Kbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A desired G.Bond port Data Rate data rate in the downstream direction,
in Kbps, to be achieved during initialization, under
restrictions placed upon the member BCEs by their respective
configuration settings.
This object represents a sum of individual BCE downstream data
rates, modified to compensate for fragmentation and
encapsulation overhead (e.g., for an Ethernet service, the
target data rate of 10Mbps 10 Mbps SHALL allow lossless transmission
of full-duplex 10Mbps 10-Mbps Ethernet frame stream with minimal
inter-frame gap).
Note that the target downstream data rate may not be achieved
during initialization (e.g., due to unavailability of required
BCEs) or the initial bandwidth could deteriorate, so that the
actual downstream data rate (gBondPortStatDnDataRate) could be
less than gBondPortConfTargetDnDataRate.

The value is limited above by 10 Gbps, to accommodate very
high speed bonded xDSL interfaces (e.g. (e.g., 32 x 100Mbps). 100 Mbps).

The value between 1 and 10000000 indicates that the total
downstream data rate of the G.Bond port after initialization
SHALL be equal to the target data rate or less, if the target
downstream data rate cannot be achieved under the restrictions
configured for BCEs. In case cases where the copper environment
allows to
achieve a higher downstream data rate to be achieved than that
specified by this object, the excess capability SHALL be
either converted to an additional SNR margin or reclaimed by
minimizing transmit power.

Changing of the Target Downstream Data Rate target downstream data rate MUST be performed
when the link is administratively 'down', as indicated by the
ifAdminStatus object in the IF-MIB.
Attempts to change this object MUST be rejected (in the case of SNMP
SNMP, with the error inconsistentValue), if the link is Up 'up' or
Initializing.
initializing.

This object maps to the TR-159 attribute aGroupTargetDownRate."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.18; RFC 2863, IF-MIB, ifAdminStatus"
::= { gBondPortConfEntry 5 }

gBondPortConfThreshLowUpRate OBJECT-TYPE
SYNTAX Unsigned32(1..10000000) Unsigned32 (1..10000000)
UNITS "Kbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the G.Bond port low upstream rate
crossing alarm threshold. When the current value of
gBondPortStatUpDataRate for this port reaches/drops below or
exceeds this threshold, a gBondLowUpRateCrossing notification
MAY be generated if enabled by
gBondPortConfLowRateCrossingEnable.

This object maps to the TR-159 attribute
aGroupthreshLowUpRate."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.21"
::= { gBondPortConfEntry 6 }

gBondPortConfThreshLowDnRate OBJECT-TYPE
SYNTAX Unsigned32(1..10000000) Unsigned32 (1..10000000)
UNITS "Kbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the G.Bond port low downstream rate
crossing alarm threshold. When the current value of
gBondPortStatDnDataRate for this port reaches/drops below or
exceeds this threshold, a gBondLowDnRateCrossing notification
MAY be generated if enabled by
gBondPortConfLowRateCrossingEnable.

This object maps to the TR-159 attribute
aGroupThreshDownUpRate."
aGroupThreshLowDownRate."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.22"
::= { gBondPortConfEntry 7 }

gBondPortConfLowRateCrossingEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether gBondLowUpRateCrossing and
gBondLowDnRateCrossing notifications should be generated
for this interface.

Value

A value of true(1) indicates that the notifications are
enabled.
Value A value of false(2) indicates that the notifications
are disabled.

This object maps to the TR-159 attribute
aGroupLowRateCrossingEnable."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.23"
::= { gBondPortConfEntry 8 }

gBondPortConfPmTcaConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) (SIZE (1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object is the index of the row in the GBS
port
Port Alarm Configuration Profile Table table for Performance Monitoring
Threshold Crossing Alerts - -- the gBondPortAlarmConfProfileTable,
which applies to this GBS port."
DEFVAL { "DEFVAL" }
::= { gBondPortConfEntry 9 }
gBondPortConfPmTcaEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the gBondPerfTca*Crossing set of
notifications should be generated for this interface.

Value

A value of true(1) indicates that the notifications are
enabled.
Value A value of false(2) indicates that the notifications
are disabled.

This object maps to the TR-159 attribute aGroupPerfTcaEnable."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.38"
::= { gBondPortConfEntry 10 }

gBondPortCapTable OBJECT-TYPE
SYNTAX SEQUENCE OF GBondPortCapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for capabilities of G.Bond Ports. ports. Entries in this table
MUST be maintained in a persistent manner" manner."
::= { gBondPort 2 }

gBondPortCapEntry OBJECT-TYPE
SYNTAX GBondPortCapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the G.Bond Port Capability table.
Each entry represents a G.Bond port indexed by the ifIndex.
Note that a G.Bond GBS port runs on top of a single
or multiple BCE port(s), which are also indexed by the ifIndex."
INDEX { ifIndex }
::= { gBondPortCapTable 1 }

GBondPortCapEntry ::=
SEQUENCE {
gBondPortCapSchemesSupported IANAgBondSchemeList,
gBondPortCapPeerSchemesSupported IANAgBondSchemeList,
gBondPortCapCapacity Unsigned32,
gBondPortCapPeerCapacity Unsigned32
}
gBondPortCapSchemesSupported OBJECT-TYPE
SYNTAX IANAgBondSchemeList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bonding Capability capability of the G.Bond port (GBS). This is a
read-only bitmap of the possible bonding schemes supported by
the GBS. The various bit-positions bit positions are:
none(0) - GBS is capable of bonding bypass on a
single-BCE (G.998.2 only) G.998.2 GBS
g9981(1) - GBS is capable of G.998.1 bonding
g9982(2) - GBS is capable of G.998.2 bonding
g9983(3) - GBS is capable of G.998.3 bonding

Note that for ports supporting multiple bonding schemes schemes, the
actual administrative scheme is set via gBondPortConfAdminScheme
object. The current operating bonding scheme is reflected in
the gBondPortStatOperScheme. gBondPortStatOperScheme object.

This object maps to the TR-159 attribute
aGroupBondSchemesSupported."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.2"
::= { gBondPortCapEntry 1 }

gBondPortCapPeerSchemesSupported OBJECT-TYPE
SYNTAX IANAgBondSchemeList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bonding Capability capability of the peer G.Bond port (GBS). This is a
read-only bitmap of the possible bonding schemes supported by
the link partner GBS. The various bit-positions bit positions are:
none(0) - peer GBS does not support bonding bonding, or
the peer unit could not be reached reached, or
peer GBS is capable of bonding bypass on a
single-BCE (G.998.2 only) G.998.2 GBS
g9981(1) - peer GBS is capable of G.998.1 bonding
g9982(2) - peer GBS is capable of G.998.2 bonding
g9983(3) - peer GBS is capable of G.998.3 bonding

Note that for ports supporting multiple bonding schemes schemes, the
actual administrative scheme is set via the
gBondPortConfPeerAdminScheme object. The current operating
bonding scheme is reflected in the gBondPortStatPeerOperScheme. gBondPortStatPeerOperScheme
object.

This object maps to the TR-159 attribute
aGroupBondPeerSchemesSupported."
aGroupPeerBondSchemesSupported."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.3"
::= { gBondPortCapEntry 2 }

gBondPortCapCapacity OBJECT-TYPE
SYNTAX Unsigned32 (1..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of BCEs that can be aggregated by the local GBS.
The number of BCEs currently assigned to a particular G.Bond
port (gBondPortStatNumBCEs) is never greater than
gBondPortCapCapacity.

This object maps to the TR-159 attribute aGroupCapacity."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.12"
::= { gBondPortCapEntry 3 }

gBondPortCapPeerCapacity OBJECT-TYPE
SYNTAX Unsigned32 (0|1..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of BCEs that can be aggregated by the peer GBS port.
Value
A value of 0 is returned when peer Bonding Capacity capacity is unknown
(peer cannot be reached).

This object maps to the TR-159 attribute aGroupPeerCapacity."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.13"
::= { gBondPortCapEntry 4 }

gBondPortStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF GBondPortStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of G.Bond
ports, complementing the generic status information from the
ifTable of the IF-MIB. Additional status information about
connected BCEs is available from the relevant line MIBs MIBs.

This table contains live data from the equipment. As such,
it is NOT persistent."
::= { gBondPort 3 }

gBondPortStatEntry OBJECT-TYPE
SYNTAX GBondPortStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the G.Bond Port Status table.
Each entry represents a G.Bond port indexed by the ifIndex.
Note that a G.Bond GBS port runs on top of a single
or multiple BCE port(s), which are also indexed by the ifIndex."
INDEX { ifIndex }
::= { gBondPortStatTable 1 }

GBondPortStatEntry ::=
SEQUENCE {
gBondPortStatOperScheme IANAgBondScheme,
gBondPortStatPeerOperScheme IANAgBondScheme,
gBondPortStatUpDataRate Gauge32,
gBondPortStatDnDataRate Gauge32,
gBondPortStatFltStatus BITS,
gBondPortStatSide INTEGER,
gBondPortStatNumBCEs Unsigned32
}

gBondPortStatOperScheme OBJECT-TYPE
SYNTAX IANAgBondScheme
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current operating bonding scheme of a G.Bond port.
The possible values are:
none(0) - bonding bypass on a single-BCE (G.998.2 only) G.998.2 GBS
g9981(1) - G.998.1 bonding
g9982(2) - G.998.2 bonding
g9983(3) - G.998.3 bonding

This object maps to the TR-159 attribute
aGroupOperBondScheme."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.4"
::= { gBondPortStatEntry 1 }

gBondPortStatPeerOperScheme OBJECT-TYPE
SYNTAX IANAgBondScheme
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current operating bonding scheme of a G.Bond port link partner.
The possible values are:
unknown(0) - peer cannot be reached due to the link state or
bonding bypass on a single-BCE (G.998.2 only) G.998.2 GBS
g9981(1) - G.998.1 bonding
g9982(2) - G.998.2 bonding
g9983(3) - G.998.3 bonding

This object maps to the TR-159 attribute
aGroupPeerOperBondScheme."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.5"
::= { gBondPortStatEntry 2 }

gBondPortStatUpDataRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A current G.Bond port operational Data Rate data rate in the upstream
direction, in bps.
This object represents an estimation of the sum of individual
BCE upstream data rates, modified to compensate for
fragmentation and encapsulation overhead (e.g., for an
Ethernet service, the target data rate of 10Mbps 10 Mbps SHALL allow
lossless transmission of full-duplex 10Mbps 10-Mbps Ethernet frame
stream with minimal inter-frame gap).

Note that for symmetrical interfaces interfaces, gBondPortStatUpDataRate ==
gBondPortStatDnDataRate == ifSpeed.

This object maps to the TR-159 attribute aGroupUpRate."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.15"
::= { gBondPortStatEntry 3 }

gBondPortStatDnDataRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A current G.Bond port operational Data Rate data rate in the downstream
direction, in bps.
This object represents an estimation of the sum of individual
BCE downstream data rates, modified to compensate for
fragmentation and encapsulation overhead (e.g., for an
Ethernet service, the target data rate of 10Mbps 10 Mbps SHALL allow
lossless transmission of full-duplex 10Mbps 10-Mbps Ethernet frame
stream with minimal inter-frame gap).

Note that for symmetrical interfaces interfaces, gBondPortStatUpDataRate ==
gBondPortStatDnDataRate == ifSpeed.

This object maps to the TR-159 attribute aGroupDownRate."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.16"
::= { gBondPortStatEntry 4 }

gBondPortStatFltStatus OBJECT-TYPE
SYNTAX BITS {
noPeer(0),
peerPowerLoss(1),
peerBondSchemeMismatch(2),
bceSubTypeMismatch(3),
lowRate(4),
init(5),
ready(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"G.Bond (GBS) port Fault Status. fault status. This is a bitmap of possible
conditions. The various bit positions are:
noPeer - peer Peer GBS cannot be reached (e.g.,
no BCEs attached, all BCEs are Down
'down', etc.).
peerPowerLoss - peer Peer GBS has indicated impending unit
failure due to loss of local power
('Dying Gasp').
peerBondSchemeMismatch - operating Operating bonding scheme of a peer
GBS is different from the local one.
bceSubTypeMismatch - local Local BCEs in the aggregation group
are not of the same sub-type, e.g.,
some BCEs in the local device are -O
while others are -R subtype.
lowRate - gBondUpRate/gBondDnRate of the port
has reached or dropped below
gBondPortConfThreshLowUpRate/
gBondPortConfThreshLowDnRate.

init - The link is Initializing, initializing, as a result
of ifAdminStatus being set to 'up'
for a particular BCE or a GBS
to which the BCE is connected.
ready - at At least one BCE in the aggregation
group is detecting handshake tones.

This object is intended to supplement the ifOperStatus object
in the IF-MIB.

This object maps to the TR-159 attribute aGroupStatus."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.9; RFC 2863, IF-MIB, ifOperStatus"
::= { gBondPortStatEntry 5 }

gBondPortStatSide OBJECT-TYPE
SYNTAX INTEGER {
subscriber(1),
office(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"G.Bond port mode of operation (subtype).
The value of 'subscriber' indicates that the port is
designated as '-R' subtype (all BCEs assigned to this port are of
subtype '-R').
The value of the 'office' indicates that the port is designated
as '-O' subtype (all BCEs assigned to this port are of
subtype '-O').
The value of 'unknown' indicates that the port has no assigned
BCEs yet or that the assigned BCEs are not of the same side
(subTypeBCEMismatch).

This object maps to the TR-159 attribute aGroupEnd."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.11"
::= { gBondPortStatEntry 6 }

gBondPortStatNumBCEs OBJECT-TYPE
SYNTAX Unsigned32 (0..32)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of BCEs that is are currently aggregated by the local GBS
(assigned to the G.Bond port using the ifStackTable).
This number is never greater than gBondPortCapCapacity.

This object SHALL be automatically incremented or decremented
when a BCE is added or deleted to/from the G.Bond port using
the ifStackTable.

This object maps to the TR-159 attribute aGroupNumChannels" aGroupNumChannels."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.14"
::= { gBondPortStatEntry 7 }

-- Performance Monitoring group

gBondPortPM OBJECT IDENTIFIER ::= { gBondPort 4 }

gBondPortPmCurTable OBJECT-TYPE
SYNTAX SEQUENCE OF GBondPortPmCurEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains current Performance Monitoring (PM)
information for a GBS port. This table contains live data from
the equipment and as such is NOT persistent."
::= { gBondPortPM 1 }

gBondPortPmCurEntry OBJECT-TYPE
SYNTAX GBondPortPmCurEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the G.Bond Port PM table.
Each entry represents a G.Bond port indexed by the ifIndex.
Note that a G.Bond GBS port runs on top of a single
or multiple BCE port(s), which are also indexed by the ifIndex."
INDEX { ifIndex }
::= { gBondPortPmCurTable 1 }

GBondPortPmCurEntry ::=
SEQUENCE {
gBondPortPmCurES HCPerfTotalCount,
gBondPortPmCurSES HCPerfTotalCount,
gBondPortPmCurUAS HCPerfTotalCount,
gBondPortPmCur15MinValidIntervals HCPerfValidIntervals,
gBondPortPmCur15MinInvalidIntervals HCPerfInvalidIntervals,
gBondPortPmCur15MinTimeElapsed HCPerfTimeElapsed,
gBondPortPmCur15MinES HCPerfCurrentCount,
gBondPortPmCur15MinSES HCPerfCurrentCount,
gBondPortPmCur15MinUAS HCPerfCurrentCount,
gBondPortPmCur1DayValidIntervals Unsigned32,
gBondPortPmCur1DayInvalidIntervals Unsigned32,
gBondPortPmCur1DayTimeElapsed HCPerfTimeElapsed,
gBondPortPmCur1DayES HCPerfCurrentCount,
gBondPortPmCur1DaySES HCPerfCurrentCount,
gBondPortPmCur1DayUAS HCPerfCurrentCount
}

gBondPortPmCurES OBJECT-TYPE
SYNTAX HCPerfTotalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Errored Seconds (ES) on the GBS since the BTU was
last restarted.

An Errored Second for a G.998.x interface is defined as a count
of 1-second intervals during which one or more GBS errors are
declared. The errors are specific for each bonding scheme, e.g. e.g.,
- lost cells for the ATM bonding; bonding
- lost or discarded (due to an error or a buffer overflow)
fragments for the Ethernet bonding; bonding
- CRC4, CRC6 CRC-4, CRC-6, or CRC8 CRC-8 errors for the TDIM bonding
This object is inhibited during Unavailable Seconds (UAS).

This object maps to the TR-159 attribute aGroupPerfES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.29"
::= { gBondPortPmCurEntry 1 }

gBondPortPmCurSES OBJECT-TYPE
SYNTAX HCPerfTotalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Severely Errored Seconds (SES) on the GBS
since the BTU was last restarted.

A Severely Errored Second for a G.998.x interface is defined as
a count of 1-second intervals during which GBS errors cause at
least 1% traffic loss of the nominal bonded link rate or at
least 12ms 12 ms for the TDM traffic. The exact definition is
specific for each bonding scheme, e.g. e.g.,
- 234 lost cells for the ATM bonding with 10Mbps 10-Mbps nominal link
rate
- 60 lost/discarded fragments for the Ethernet bonding with
10Mbps
10-Mbps nominal link rate and fixed 192 Byte-long 192-byte-long fragment
size.
size
- 6 or more CRC4, CRC-4 errors, one or more CRC6 CRC-6 errors, or one or
more CRC8 CRC-8 errors for the TDM bonding
This object is inhibited during Unavailable Seconds (UAS).

This object maps to the TR-159 attribute aGroupPerfSES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.30"
::= { gBondPortPmCurEntry 2 }

gBondPortPmCurUAS OBJECT-TYPE
SYNTAX HCPerfTotalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Unavailable Seconds (UAS) on the GBS since the BTU
was last restarted.

An Unavailable Second for a G.998.x interface is defined as a
count of 1-second intervals during which the bonded link is
unavailable. The G.998.x link becomes unavailable at the onset
of 10 contiguous SESs. The 10 SESs are included in the
unavailable time. Once unavailable, the G.998.x line becomes
available at the onset of 10 contiguous seconds with no SESs.
The 10 seconds with no SESs are excluded from the unavailable
time.

This object maps to the TR-159 attribute aGroupPerfUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.31"
::= { gBondPortPmCurEntry 3 }

gBondPortPmCur15MinValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of 15-minute intervals for which data was collected.
The value of this object will be 96 or the maximum number of
15-minute history intervals collected by the implementation implementation,
unless the measurement was (re-)started (re)started recently, in which case
the value will be the number of complete 15 minutes 15-minute intervals
for which there are at least some data.

In certain cases cases, it is possible that some intervals are
unavailable. In this case, this object reports the maximum
interval number for which data is available.

This object maps to the TR-159 attribute
aGroupPerf15MinValidIntervals."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.32"
::= { gBondPortPmCurEntry 4 }

gBondPortPmCur15MinInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of 15-minute intervals for which data was not always
available. The value will typically be zero zero, except in cases
where the data for some intervals are not available.

This object maps to the TR-159 attribute
aGroupPerf15MinInvalidIntervals."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.33"
::= { gBondPortPmCurEntry 5 }

gBondPortPmCur15MinTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of seconds that have elapsed since the beginning of the
current 15-minute performance interval.

This object maps to the TR-159 attribute
aGroupPerfCurr15MinTimeElapsed."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.34"
::= { gBondPortPmCurEntry 6 }

gBondPortPmCur15MinES OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Errored Seconds (ES) on the GBS in the current
15-minute performance interval.

This object maps to the TR-159 attribute aGroupPerfCurr15MinES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.35"
::= { gBondPortPmCurEntry 7 }

gBondPortPmCur15MinSES OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Severely Errored Seconds (ES) (SES) on the GBS in the
current 15-minute performance interval.

This object maps to the TR-159 attribute aGroupPerfCurr15MinSES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.36"
::= { gBondPortPmCurEntry 8 }

gBondPortPmCur15MinUAS OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Unavailable Seconds (UAS) on the GBS in the current
15-minute performance interval.

This object maps to the TR-159 attribute aGroupPerfCurr15MinUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.37"
::= { gBondPortPmCurEntry 9 }

gBondPortPmCur1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32 (0..7)
UNITS "days"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of 1-day intervals for which data was collected.
The value of this object will be 7 or the maximum number of
1-day history intervals collected by the implementation implementation, unless
the measurement was (re-)started (re)started recently, in which case the
value will be the number of complete 1-day intervals for which
there are at least some data.
In certain cases cases, it is possible that some intervals are
unavailable. In this case, this object reports the maximum
interval number for which data is available.

This object maps to the TR-159 attribute
aGroupPerf1DayValidIntervals."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.45"
::= { gBondPortPmCurEntry 10 }

gBondPortPmCur1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32 (0..7)
UNITS "days"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A number of 1-day intervals for which data was not always
available. The value will typically be zero zero, except in cases
where the data for some intervals are not available.

This object maps to the TR-159 attribute
aGroupPerf1DayInvalidIntervals."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.46"
::= { gBondPortPmCurEntry 11 }

gBondPortPmCur1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of seconds that have elapsed since the beginning of
the current 1-day performance interval.

This object maps to the TR-159 attribute
aGroupPerfCurr1DayTimeElapsed."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.47"
::= { gBondPortPmCurEntry 12 }

gBondPortPmCur1DayES OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Errored Seconds (ES) on the GBS in the current 1-day
performance interval.

This object maps to the TR-159 attribute aGroupPerfCurr1DayES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.48"
::= { gBondPortPmCurEntry 13 }

gBondPortPmCur1DaySES OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Severely Errored Seconds (ES) (SES) on the GBS in the
current 1-day performance interval.

This object maps to the TR-159 attribute aGroupPerfCurr1DaySES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.49"
::= { gBondPortPmCurEntry 14 }

gBondPortPmCur1DayUAS OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Unavailable Seconds (UAS) on the GBS in the current
1-day performance interval.

This object maps to the TR-159 attribute aGroupPerfCurr1DayUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.50"
::= { gBondPortPmCurEntry 15 }

-- PM history: 15-min buckets

gBondPortPm15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF GBondPortPm15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains historical 15-minute buckets of Performance
Monitoring information for a GBS port (a row for each 15-minute
interval, up to 96 intervals).
Entries in this table MUST be maintained in a persistent manner."
::= { gBondPortPM 2 }

gBondPortPm15MinEntry OBJECT-TYPE
SYNTAX GBondPortPm15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the G.Bond Port historical 15-minute PM table.
Each entry represents performance monitoring Performance Monitoring data for a GBS port,
indexed by the ifIndex, collected during a particular 15-minute
interval, indexed by the gBondPortPm15MinIntervalIndex."
INDEX { ifIndex, gBondPortPm15MinIntervalIndex }
::= { gBondPortPm15MinTable 1 }

GBondPortPm15MinEntry ::=
SEQUENCE {
gBondPortPm15MinIntervalIndex Unsigned32,
gBondPortPm15MinIntervalMoniTime HCPerfTimeElapsed,
gBondPortPm15MinIntervalES HCPerfIntervalCount,
gBondPortPm15MinIntervalSES HCPerfIntervalCount,
gBondPortPm15MinIntervalUAS HCPerfIntervalCount,
gBondPortPm15MinIntervalValid TruthValue
}

gBondPortPm15MinIntervalIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval data interval number. 1 is the most recent
previous interval; interval 96 is 24 hours ago.
Intervals 2..96 are OPTIONAL.

This object maps to the TR-159 attribute
aGroupPerf15MinIntervalNumber."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.57"
::= { gBondPortPm15MinEntry 1 }

gBondPortPm15MinIntervalMoniTime OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of seconds over which the performance data was actually
monitored. This value will be the same as the interval duration
(900 seconds), except in a situation where performance data
could not be collected for any reason."
::= { gBondPortPm15MinEntry 2 }
gBondPortPm15MinIntervalES OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Errored Seconds (ES) on the GBS in the 15-minute
performance history interval.

This object maps to the TR-159 attribute
aGroupPerf15MinIntervalES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.59"
::= { gBondPortPm15MinEntry 3 }

gBondPortPm15MinIntervalSES OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Severely Errored Seconds (ES) (SES) on the GBS in the
15-minute performance history interval.

This object maps to the TR-159 attribute
aGroupPerf15MinIntervalSES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.60"
::= { gBondPortPm15MinEntry 4 }

gBondPortPm15MinIntervalUAS OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Unavailable Seconds (UAS) on the GBS in the current
15-minute performance interval.

This object maps to the TR-159 attribute aGroupPerfCurr15MinUAS."
aGroupPerf15MinIntervalUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.61"
::= { gBondPortPm15MinEntry 5 }

gBondPortPm15MinIntervalValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only object indicating whether or not this history
bucket contains valid data. Valid A valid bucket is reported as
true(1) and an invalid bucket as false(2).
If this history bucket is invalid invalid, the BTU-C MUST NOT produce
notifications based upon the value of the counters in this
bucket.
Note that an implementation may decide not to store invalid
history buckets in its data base. database. In such case a case, this object
is not required required, as only valid history buckets are available
while invalid history buckets are simply not in the data base. database.

This object maps to the TR-159 attribute
aGroupPerf15MinIntervalValid."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.58"
::= { gBondPortPm15MinEntry 6 }

-- PM history: 1-day buckets

gBondPortPm1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF GBondPortPm1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains historical 1-day buckets of Performance
Monitoring information for a GBS port (a row for each 1-day
interval, up to 7 intervals).
Entries in this table MUST be maintained in a persistent manner."
::= { gBondPortPM 3 }

gBondPortPm1DayEntry OBJECT-TYPE
SYNTAX GBondPortPm1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the G.Bond Port historical 1-day PM table.
Each entry represents performance monitoring Performance Monitoring data for a GBS port,
indexed by the ifIndex, collected during a particular 1-day
interval, indexed by the gBondPortPm1DayIntervalIndex."
INDEX { ifIndex, gBondPortPm1DayIntervalIndex }
::= { gBondPortPm1DayTable 1 }

GBondPortPm1DayEntry ::=
SEQUENCE {
gBondPortPm1DayIntervalIndex Unsigned32,
gBondPortPm1DayIntervalMoniTime HCPerfTimeElapsed,
gBondPortPm1DayIntervalES HCPerfIntervalCount,
gBondPortPm1DayIntervalSES HCPerfIntervalCount,
gBondPortPm1DayIntervalUAS HCPerfIntervalCount,
gBondPortPm1DayIntervalValid TruthValue
}

gBondPortPm1DayIntervalIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..7)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval data interval number. 1 is the most recent
previous interval; interval 7 is 7 days ago.
Intervals 2..7 are OPTIONAL.

This object maps to the TR-159 attribute
aGroupPerf1DayIntervalNumber."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.62"
::= { gBondPortPm1DayEntry 1 }

gBondPortPm1DayIntervalMoniTime OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of seconds over which the performance data was actually
monitored. This value will be the same as the interval duration
(86400 seconds), except in a situation where performance data
could not be collected for any reason.

This object maps to the TR-159 attribute
aGroupPerf1DayIntervalMoniSecs."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.64"
::= { gBondPortPm1DayEntry 2 }

gBondPortPm1DayIntervalES OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Errored Seconds (ES) on the GBS in the 1-day
performance history interval.

This object maps to the TR-159 attribute
aGroupPerf1DayIntervalES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.65"
::= { gBondPortPm1DayEntry 3 }

gBondPortPm1DayIntervalSES OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Severely Errored Seconds (ES) (SES) on the GBS in the
1-day performance history interval.

This object maps to the TR-159 attribute
aGroupPerf1DayIntervalSES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.66"
::= { gBondPortPm1DayEntry 4 }

gBondPortPm1DayIntervalUAS OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of Unavailable Seconds (UAS) on the GBS in the current
1-day performance interval.

This object maps to the TR-159 attribute aGroupPerfCurr1DayUAS."
aGroupPerf1DayIntervalUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.67"
::= { gBondPortPm1DayEntry 5 }

gBondPortPm1DayIntervalValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A read-only object indicating whether or not this history
bucket contains valid data. Valid A valid bucket is reported as
true(1) and an invalid bucket as false(2).
If this history bucket is invalid invalid, the BTU-C MUST NOT produce
notifications based upon the value of the counters in this
bucket.

Note that an implementation may decide not to store invalid
history buckets in its data base. database. In such case a case, this object
is not required required, as only valid history buckets are available
while invalid history buckets are simply not in the data base. database.

This object maps to the TR-159 attribute
aGroupPerf1DayIntervalValid."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.63"
::= { gBondPortPm1DayEntry 6 }

-- Performance Monitoring TCA Configuration profile

gBondPortPmTcaProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF GBondPortPmTcaProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of Performance Monitoring (PM)
Threshold Crossing Alerts Alert (TCA) configuration profiles for GBS
ports.
Entries in this table MUST be maintained in a persistent manner."
::= { gBondPortPM 4 }

gBondPortPmTcaProfileEntry OBJECT-TYPE
SYNTAX GBondPortPmTcaProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the GBS PM TCA Configuration table.
Each entry corresponds to a single TCA configuration profile.
Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at GBS
ports. Profiles may be created/deleted using the row
creation/deletion mechanism via
gBondPortPmTcaProfileRowStatus. If an active entry is
referenced via gBondPortConfPmTcaConfProfile, the entry MUST
remain active until all references are removed.
A default profile with an index of 'DEFVAL', 'DEFVAL' will always exist exist,
and its parameters will be set to vendor specific values, vendor-specific values
unless otherwise specified in this document."
INDEX { gBondPortPmTcaProfileName }
::= { gBondPortPmTcaProfileTable 1 }
GBondPortPmTcaProfileEntry ::=
SEQUENCE {
gBondPortPmTcaProfileName SnmpAdminString,
gBondPortPmTcaProfileThresh15MinES HCPerfIntervalThreshold,
gBondPortPmTcaProfileThresh15MinSES HCPerfIntervalThreshold,
gBondPortPmTcaProfileThresh15MinUAS HCPerfIntervalThreshold,
gBondPortPmTcaProfileThresh1DayES GBondPm1DayIntervalThreshold,
gBondPortPmTcaProfileThresh1DaySES GBondPm1DayIntervalThreshold,
gBondPortPmTcaProfileThresh1DayUAS GBondPm1DayIntervalThreshold,
gBondPortPmTcaProfileRowStatus RowStatus
}

gBondPortPmTcaProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is a unique index (name) associated with this
GBS PM TCA profile."
::= { gBondPortPmTcaProfileEntry 1 }

gBondPortPmTcaProfileThresh15MinES OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A desired threshold for the number of Errored Seconds (ES)
within any given 15-minute performance data collection interval.
If the number of ESs in a particular 15-minute collection
interval reaches or exceeds this value, a
gBondPmTca15MinESCrossing notification MAY be generated if
enabled by gBondPortConfPmTcaEnable.
At most one notification can be sent per interval.
Setting this attribute to zero (default) effectively disables
the gBondPmTca15MinESCrossing notification.

This object maps to the TR-159 attribute
aGroupPerfThreshold15MinES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.39"
::= { gBondPortPmTcaProfileEntry 2 }

gBondPortPmTcaProfileThresh15MinSES OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A desired threshold for the number of Severely Errored Seconds
(SES) within any given 15-minute performance data collection
interval.
If the number of SESs in a particular 15-minute collection
interval reaches or exceeds this value, a
gBondPmTca15MinSESCrossing notification MAY be generated if
enabled by gBondPortConfPmTcaEnable.
At most one notification can be sent per interval.
Setting this attribute to zero (default) effectively disables
the gBondPmTca15MinSESCrossing notification.

This object maps to the TR-159 attribute
aGroupPerfThreshold15MinSES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.40"
::= { gBondPortPmTcaProfileEntry 3 }

gBondPortPmTcaProfileThresh15MinUAS OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A desired threshold for the number of Unavailable Seconds (UAS)
within any given 15-minute performance data collection interval.
If the number of UASs in a particular 15-minute collection
interval reaches or exceeds this value, a
gBondPmTca15MinUASCrossing notification MAY be generated if
enabled by gBondPortConfPmTcaEnable.
At most one notification can be sent per interval.
Setting this attribute to zero (default) effectively disables
the gBondPmTca15MinUASCrossing notification.

This object maps to the TR-159 attribute
aGroupPerfThreshold15MinUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.41"
::= { gBondPortPmTcaProfileEntry 4 }

gBondPortPmTcaProfileThresh1DayES OBJECT-TYPE
SYNTAX GBondPm1DayIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A desired threshold for the number of Errored Seconds (ES)
within any given 1-day performance data collection interval.

If the number of ESs in a particular 1-day collection interval
reaches or exceeds this value, a gBondPmTca1DayESCrossing
notification MAY be generated if enabled by
gBondPortConfPmTcaEnable.
At most one notification can be sent per interval.
Setting this attribute to zero (default) effectively disables
the gBondPmTca1DayESCrossing notification.

This object maps to the TR-159 attribute
aGroupPerfThreshold1DayES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.51"
::= { gBondPortPmTcaProfileEntry 5 }

gBondPortPmTcaProfileThresh1DaySES OBJECT-TYPE
SYNTAX GBondPm1DayIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A desired threshold for the number of Severely Errored Seconds
(SES) within any given 1-day performance data collection
interval.
If the number of SESs in a particular 1-day collection interval
reaches or exceeds this value, a gBondPmTca1DaySESCrossing
notification MAY be generated if enabled by
gBondPortConfPmTcaEnable.
At most one notification can be sent per interval.
Setting this attribute to zero (default) effectively disables
the gBondPmTca1DaySESCrossing notification.

This object maps to the TR-159 attribute
aGroupPerfThreshold1DaySES."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.52"
::= { gBondPortPmTcaProfileEntry 6 }

gBondPortPmTcaProfileThresh1DayUAS OBJECT-TYPE
SYNTAX GBondPm1DayIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A desired threshold for the number of Unavailable Seconds (UAS)
within any given 1-day performance data collection interval.
If the number of UASs in a particular 1-day collection interval
reaches or exceeds this value, a gBondPmTca1DayUASCrossing
notification MAY be generated if enabled by
gBondPortConfPmTcaEnable.
At most one notification can be sent per interval.
Setting this attribute to zero (default) effectively disables
the gBondPmTca1DayUASCrossing notification.

This object maps to the TR-159 attribute
aGroupPerfThreshold1DayUAS."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.1.53"
::= { gBondPortPmTcaProfileEntry 7 }

gBondPortPmTcaProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls the creation, modification, or deletion
of the associated entry in the gBondPortPmTcaProfileTable
per the semantics of RowStatus.

If an 'active' entry is referenced via
gBondPortConfPmTcaConfProfile instance(s), the entry MUST
remain 'active'.

An 'active' entry SHALL NOT be modified. In order to modify an
existing entry, it MUST be taken out of service (by setting
this object to 'notInService'), modified, and set to 'active'
again."
::= { gBondPortPmTcaProfileEntry 8 }

-- The BCE group

gBondBceConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF GBondBceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table for Configuration configuration of G.Bond common aspects for the
Bonding Channel Entity (BCE) ports (modems/channels).

Entries in this table MUST be maintained in a persistent
manner."
::= { gBondBce 1 }

gBondBceConfEntry OBJECT-TYPE
SYNTAX GBondBceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the G.Bond BCE Configuration table.
Each entry represents common aspects of a G.Bond BCE port
indexed by the ifIndex. Note that a G.Bond BCE port can be
stacked below a single GBS port, also indexed by the ifIndex,
possibly together with other BCE ports if GAF bonding is enabled."
INDEX { ifIndex }
::= { gBondBceConfTable 1 }

GBondBceConfEntry ::=
SEQUENCE {
gBondBceConfRemoteDiscoveryCode PhysAddress
}

gBondBceConfRemoteDiscoveryCode OBJECT-TYPE
SYNTAX PhysAddress (SIZE(0|6)) (SIZE (0|6))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A Remote Discovery Code remote discovery code of the BCE port at the CO.
A 6 octet long Discovery Code 6-octet-long discovery code of the peer GBS connected via
the BCE.
Reading this object results in a Discovery Get operation.
Setting this object to all zeroes results in a Discovery
Clear_if_Same operation (the value of gBondPortConfDiscoveryCode
at the peer GBS SHALL be the same as gBondPortConfDiscoveryCode
of the local GBS associated with the BCE for the operation to
succeed).
Writing a non-zero value to this object results in a
Discovery Set_if_Clear operation.
A zero-length octet string SHALL be returned on an attempt to
read this object when GAF aggregation bonding is not enabled.

This object is irrelevant in BCE-R port subtypes (CPE side):
in this case case, a zero length zero-length octet string SHALL be returned on
an attempt to read this object, an object. An attempt to change this
object MUST be rejected (in the case of SNMP SNMP, with the error
inconsistentValue).

Discovery MUST be performed when the link is Down. 'down'.
Attempts to change this object MUST be rejected (in the case of
SNMP
SNMP, with the error inconsistentValue), If the link is Up 'up' or
Initializing.
initializing.

This object maps to the TR-159 attribute
aLineRemoteDiscoveryCode."
REFERENCE
"[TR-159]
"[TR-159], Section 5.5.6.7"
::= { gBondBceConfEntry 1 }

--
-- Conformance Statements
--

gBondGroups OBJECT IDENTIFIER ::= { gBondConformance 1 }

gBondCompliances OBJECT IDENTIFIER ::= { gBondConformance 2 }

-- Object Groups

gBondBasicGroup OBJECT-GROUP
OBJECTS {
gBondPortStatOperScheme,
gBondPortStatUpDataRate,
gBondPortStatDnDataRate,
gBondPortConfTargetUpDataRate,
gBondPortConfTargetDnDataRate,
gBondPortCapSchemesSupported,
gBondPortCapCapacity,
gBondPortStatNumBCEs,
gBondPortStatSide,
gBondPortStatFltStatus
}
STATUS current
DESCRIPTION
"A collection of objects representing management information
common to all types of G.Bond ports."
::= { gBondGroups 1 }

gBondDiscoveryGroup OBJECT-GROUP
OBJECTS {
gBondPortStatPeerOperScheme,
gBondPortCapPeerSchemesSupported,
gBondPortCapPeerCapacity,
gBondPortConfDiscoveryCode,
gBondBceConfRemoteDiscoveryCode
}
STATUS current
DESCRIPTION
"A collection of objects supporting OPTIONAL G.Bond discovery
in G.Bond ports."
::= { gBondGroups 2 }
gBondMultiSchemeGroup OBJECT-GROUP
OBJECTS {
gBondPortConfAdminScheme,
gBondPortConfPeerAdminScheme
}
STATUS current
DESCRIPTION
"A collection of objects providing OPTIONAL management
information for G.Bond ports supporting multiple bonding
schemes."
::= { gBondGroups 3 }

gBondTcaConfGroup OBJECT-GROUP
OBJECTS {
gBondPortConfThreshLowUpRate,
gBondPortConfThreshLowDnRate,
gBondPortConfLowRateCrossingEnable
}
STATUS current
DESCRIPTION
"A collection of objects required for configuration of alarm
thresholds and notifications in G.Bond ports."
::= { gBondGroups 4 }

gBondTcaNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
gBondLowUpRateCrossing,
gBondLowDnRateCrossing
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
(non-PM threshold crossing alerts) associated with G.Bond ports."
::= { gBondGroups 5 }

gBondPmCurGroup OBJECT-GROUP
OBJECTS {
gBondPortPmCurES,
gBondPortPmCurSES,
gBondPortPmCurUAS,
gBondPortPmCur15MinValidIntervals,
gBondPortPmCur15MinInvalidIntervals,
gBondPortPmCur15MinTimeElapsed,
gBondPortPmCur15MinES,
gBondPortPmCur15MinSES,
gBondPortPmCur15MinUAS,
gBondPortPmCur1DayValidIntervals,
gBondPortPmCur1DayInvalidIntervals,
gBondPortPmCur1DayTimeElapsed,
gBondPortPmCur1DayES,
gBondPortPmCur1DaySES,
gBondPortPmCur1DayUAS
}
STATUS current
DESCRIPTION
"A collection of objects supporting OPTIONAL current Performance
Monitoring information for G.Bond ports."
::= { gBondGroups 6 }

gBondPm15MinGroup OBJECT-GROUP
OBJECTS {
gBondPortPm15MinIntervalMoniTime,
gBondPortPm15MinIntervalES,
gBondPortPm15MinIntervalSES,
gBondPortPm15MinIntervalUAS,
gBondPortPm15MinIntervalValid
}
STATUS current
DESCRIPTION
"A collection of objects supporting OPTIONAL historical
Performance Monitoring information for G.Bond ports, during
previous 15-minute intervals ." intervals."
::= { gBondGroups 7 }

gBondPm1DayGroup OBJECT-GROUP
OBJECTS {
gBondPortPm1DayIntervalMoniTime,
gBondPortPm1DayIntervalES,
gBondPortPm1DayIntervalSES,
gBondPortPm1DayIntervalUAS,
gBondPortPm1DayIntervalValid
}
STATUS current
DESCRIPTION
"A collection of objects supporting OPTIONAL historical
Performance Monitoring information for G.Bond ports, during
previous 1-day intervals ." intervals."
::= { gBondGroups 8 }

gBondPmTcaConfGroup OBJECT-GROUP
OBJECTS {
gBondPortConfPmTcaConfProfile,
gBondPortConfPmTcaEnable,
gBondPortPmTcaProfileThresh15MinES,
gBondPortPmTcaProfileThresh15MinSES,
gBondPortPmTcaProfileThresh15MinUAS,
gBondPortPmTcaProfileThresh1DayES,
gBondPortPmTcaProfileThresh1DaySES,
gBondPortPmTcaProfileThresh1DayUAS,
gBondPortPmTcaProfileRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects required for configuration of
Performance Monitoring Threshold Crossing Alert notifications
in G.Bond ports."
::= { gBondGroups 9 }

gBondPmTcaNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
gBondPmTca15MinESCrossing,
gBondPmTca15MinSESCrossing,
gBondPmTca15MinUASCrossing,
gBondPmTca1DayESCrossing,
gBondPmTca1DaySESCrossing,
gBondPmTca1DayUASCrossing
}
STATUS current
DESCRIPTION
"This group supports notifications of performance monitoring
thresholds crossing alerts Performance Monitoring
Threshold Crossing Alerts associated with G.Bond ports."
::= { gBondGroups 10 }

-- Compliance Statements

gBondCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for G.Bond interfaces.
Compliance with the following external compliance statements
is REQUIRED:

MIB Module Compliance Statement
---------- --------------------
IF-MIB ifCompliance3

Compliance with the following external compliance statements
is OPTIONAL for implementations supporting bonding with
flexible cross-connect between the GBS and BCE ports:

MIB Module Compliance Statement
---------- --------------------
IF-INVERTED-STACK-MIB ifInvCompliance
IF-CAP-STACK-MIB ifCapStackCompliance"
MODULE -- this module
MANDATORY-GROUPS {
gBondBasicGroup,
gBondTcaConfGroup,
gBondTcaNotificationGroup
}

GROUP gBondDiscoveryGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting the G.Bond Discovery function."

GROUP gBondMultiSchemeGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting multiple bonding schemes."

GROUP gBondPmCurGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting Performance Monitoring."

GROUP gBondPm15MinGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting 15-min 15-minute historical Performance Monitoring."

GROUP gBondPm1DayGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting 1-day historical Performance Monitoring."

GROUP gBondPmTcaConfGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting Performance Monitoring Threshold Crossing Alert
notifications."

GROUP gBondPmTcaNotificationGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting Performance Monitoring Threshold Crossing Alert
notifications."

OBJECT gBondPortCapSchemesSupported
SYNTAX IANAgBondSchemeList
DESCRIPTION
"Support for all bonding Schemes scheme types is not required.
However

However, at least one value SHALL be supported" supported."

OBJECT gBondPortCapPeerSchemesSupported
SYNTAX IANAgBondSchemeList
DESCRIPTION
"Support for all bonding Schemes scheme types is not required.
However
However, at least one value SHALL be supported" supported."

::= { gBondCompliances 1 }
END

7. IANA-maintained IANA-Maintained G.Bond TC Definitions

The IANA-GBOND-TC-MIB module IMPORTS objects from SNMPv2-SMI
[RFC2578] and SNMPv2-TC [RFC2579].

IANA-GBOND-TC-MIB DEFINITIONS ::= BEGIN

IMPORTS
MODULE-IDENTITY,
mib-2
FROM SNMPv2-SMI
TEXTUAL-CONVENTION
FROM SNMPv2-TC
;
------------------------------------------------------------------------
ianaGBondTcMIB MODULE-IDENTITY
LAST-UPDATED "201207160000Z" "201302200000Z" -- July 16, 2012 20 February 2013
ORGANIZATION "IANA"
CONTACT-INFO " Internet Assigned Numbers Authority

Postal: ICANN
4676 Admiralty Way,
12025 Waterfront Drive, Suite 330
Marina del Rey, 300
Los Angeles, CA 90292 90094-2536

Tel: +1-310-823-9358 +1-310-301-5800
EMail: iana@iana.org"

DESCRIPTION
"This MIB module defines IANAgBondScheme and IANAgBondSchemeList
TEXTUAL-CONVENTIONs, specifying enumerated values of the
gBondPortConfAdminScheme, gBondPortConfPeerAdminScheme,
gBondPortStatOperScheme, gBondPortStatPeerOperScheme and gBondPortStatPeerOperScheme,
gBondPortCapSchemesSupported, and gBondPortCapPeerSchemesSupported
objects
objects, respectively, as defined in the GBOND-MIB.

It is intended that each new bonding scheme defined by the
ITU-T Q4/SG15 working group and approved for publication in a
revision of the ITU-T G.998 specification will be added to this
MIB module, provided that it is suitable for being managed by the
base objects in the GBOND-MIB. An Expert Review, as defined in
RFC 5226 [RFC5226], 5226, is REQUIRED for such additions.

The following references are used throughout this MIB module:

[G.998.1] refers to:
ITU-T Recommendation G.998.1: 'ATM-based multi-pair bonding',
January 2005.

[G.998.2] refers to:
ITU-T Recommendation G.998.2: 'Ethernet-based multi-pair
bonding', January 2005.

[G.998.3] refers to:
ITU-T Recommendation G.998.3: 'Multi-pair bonding using
time-division inverse multiplexing', January 2005.

Naming Conventions:
BCE - Bonding Channel Entity
GBS - Generic Bonding Sublayer Sub-layer

These references should be updated as appropriate when a new
bonding scheme is added to this MIB module.

Redistribution and use in
RFC XXXX; for full legal notices see source and binary forms, with or without
modification, is permitted pursuant to, and subject to the RFC itself.
Supplementary information may be available at:
http://www.ietf.org/copyrights/ianamib.html" license
terms contained in, the Simplified BSD License set forth in
Section 4.c of the IETF Trust's Legal Provisions Relating to IETF
Documents (http://trustee.ietf.org/license-info)."

REVISION "201207160000Z" "201302200000Z" -- Jul 16, 2012 20 February 2013
DESCRIPTION "Initial version, published as RFC XXXX."

-- EdNote: Replace XXXX with the actual RFC number &
-- remove this note 6765."

::= { mib-2 ZZZ 215 }

-- EdNote: Replace ZZZ with a real OID once it is
-- allocated & remove this note.

-- Textual Conventions

IANAgBondSchemeList ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention defines a bitmap of possible ITU-T
G.998 (G.Bond) bonding schemes. Currently Currently, the following values
are defined for the corresponding bonding schemes:
g9981(1) - G.998.1, (G.Bond/ATM, G.998.1 (G.Bond/ATM; see the G9981-MIB)
g9982(2) - G.998.2, (G.Bond/Ethernet, G.998.2 (G.Bond/Ethernet; see the G9982-MIB)
g9983(3) - G.998.3, (G.Bond/TDIM, G.998.3 (G.Bond/TDIM; see the G9983-MIB)
An additional value of none(0), none(0) can be returned as a result
of a GET operation, operation when an a value of the object cannot be
determined (for example example, a peer GBS cannot be reached), the port
does not support any kind of bonding bonding, or when a single-BCE
G.998.2 GBS supports bonding (frame fragmentation/reassembly)
bypass."
SYNTAX BITS {
none(0),
g9981(1),
g9982(2),
g9983(3)
}

IANAgBondScheme ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual convention defines ITU-T G.998 bonding scheme
values. Possible values are:
none(0) - no bonding (e.g. (e.g., on a single-BCE G.998.2 GBS)
or unknown
g9981(1) - G.998.1 (G.Bond/ATM)
g9982(2) - G.998.2 (G.Bond/Ethernet)
g9983(3) - G.998.3 (G.Bond/TDIM)." (G.Bond/TDIM)"
SYNTAX INTEGER {
none(0),
g9981(1),
g9982(2),
g9983(3)
}

END

8. Security Considerations

There is are a number of managed management objects defined in this MIB module
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:

o Changing of the gBondPortConfAdminScheme object may lead to a
potential locking of the link, if the peer device does not support
the desired bonding scheme.

o Changing of gBondPortConfDiscoveryCode, the gBondPortConfDiscoveryCode object, before the
discovery operation, may lead to a wrongful discovery, discovery -- for example
example, when two CO ports are connected to the same multi-channel
RT port, while both CO ports have the same discovery register
value.

o Changing of the target upstream/downstream data rate via
gBondPortConfTargetUpDataRate/gBondPortConfTargetDnDataRate may
lead to anything from degradation of link quality and data rate degradation to
a complete link initialization failure, as the ability of a G.Bond
port to support a particular configuration depends on the copper
environment.

o Activation of a specific line/channel may cause a severe
degradation of service for another G.Bond port, whose channel(s)
may be affected by the cross-talk from the newly activated
channel.

o Removal of a channel from an operationally 'up' G.Bond port,
aggregating several channels, may cause port's rate degradation of the port's
data rate.

Some of the readable objects in this MIB module (i.e., those with
MAX-ACCESS other than not-accessible) may be considered sensitive or
vulnerable in some network environments since, collectively, they
provide information about the performance of network interfaces and
can reveal some aspects of their configuration.

In particular, since a bonded xDSL port can be comprised of multiple
Unshielded Twisted Pair (UTP) voice grade voice-grade copper, located in the same
bundle with other pairs belonging to another operator/customer, it is
theoretically possible to eavesdrop to on a G.Bond transmission, simply
by "listening" to a cross-talk from the bonded pairs, especially if the
operating parameters of the G.Bond link in question are known.

It is thus important to control even GET and/or NOTIFY access to
these objects and possibly to even encrypt the values of these
objects when sending them over the network via SNMP. These are the
tables and objects and their sensitivity/vulnerability:

o gBondPortStatTable - objects in this table provide status
information for the G.Bond port, which may aid in identification
of the pairs belonging to the bonded port and eavesdroping to eavesdropping on the
traffic over that port.

SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPSec), IPsec),
there is no control as to who on the secure network is allowed to
access and GET/SET (read/change/create/delete) the objects in this
MIB module.

Implementations MUST SHOULD provide the security features described by the
SNMPv3 framework (see [RFC3410]), including and implementations claiming
compliance to the SNMPv3 standard MUST include full support for
authentication and privacy via the User-based Security Model (USM)
[RFC3414] with the AES cipher algorithm [RFC3826]. Implementations
MAY also provide support for the Transport Security Model (TSM)
[RFC5591] in combination with a secure transport such as SSH
[RFC5592] or TLS/DTLS [RFC6353].

Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.

9. IANA Considerations

Three new values of IANAifType: IANAifType -- g9981(263), g9982(264) g9982(264), and
g9983(265) -- have been allocated by IANA [1] <http://www.iana.org/> in
the IANAifType-MIB module [IANAifType-MIB].

An object identifier for gBondMIB MODULE-IDENTITY SHALL be has been allocated
by IANA in the MIB-2 transmission sub-tree, before this document is
published. sub-tree (211).

This document defines the first version of the IANA-maintained IANA-
GBOND-MIB
GBOND-TC-MIB module. It is intended that each new G.998 bonding
scheme defined by the ITU-T Q4/SG15 working group and approved for
publication in a revision of ITU-T G.998.x is will be added to the IANA-
maintaned
maintained MIB module, provided that it is suitable for being managed
by the base objects in the GBOND-MIB module. An object identifier
for ianaGBondTcMIB MODULE-IDENTITY has been allocated by IANA in the
MIB-2 transmission sub-tree (215).

For each new bonding scheme added, a short description of the bonding
protocol and, wherever possible, a reference to a publicly available
specification SHOULD be specified. An Expert Review, as defined in
[RFC5226].,
[RFC5226], is REQUIRED, REQUIRED for each modification.

10. Acknowledgments

This document was produced by the [ADSLMIB] working group.

Special thanks to Dan Romascanu for his meticulous review of this
text.

11. References

11.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.

[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.

[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
STD 58, RFC 2579, April 1999.

[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.

[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.

[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
December 2002.

[RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", STD 62, RFC 3414, December 2002.

[RFC3705] Ray, B. and R. Abbi, "High Capacity Textual Conventions
for MIB Modules Using Performance History Based on 15
Minute Intervals", RFC 3705, February 2004.

[RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The
Advanced Encryption Standard (AES) Cipher Algorithm in the
SNMP User-based Security Model", RFC 3826, June 2004.

[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.

[RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model
for the Simple Network Management Protocol (SNMP)",
RFC 5591, June 2009.

[RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure
Shell Transport Model for the Simple Network Management
Protocol (SNMP)", RFC 5592, June 2009.

[RFC6353] Hardaker, W., "Transport Layer Security (TLS) Transport
Model for the Simple Network Management Protocol (SNMP)",
RFC 6353, July 2011.

[TR-159] Beili, E. and M. Morgenstern, "Management Framework for
xDSL Bonding", Broadband Forum
technical report Technical Report TR-159,
December 2008. 2008, <http://www.broadband-forum.org/technical/
download/TR-159.pdf>.

11.2. Informative References

[802.3] IEEE, "IEEE Standard for Information technology -
Telecommunications and information exchange between
systems - Local and metropolitan area networks - Specific
requirements - Part 3: Carrier Sense Multiple Access with
Collision Detection (CSMA/CD) Access Method and Physical
Layer Specifications", IEEE Std 802.3-
2005, 802.3-2005, December 2005.

[ADSLMIB] IETF, "ADSL MIB (adslmib) Charter", <http://www.ietf.org/
html.charters/
adslmib-charter.html>.

[G.991.2] ITU-T, "Single-pair High-speed
Digital Subscriber Line (SHDSL)
transceivers", ITU-T
Recommendation G.991.2,
December 2003, <http://
www.itu.int/rec/T-REC-G.991.2/en>.

[G.993.1] ITU-T, "Very High speed Digital
Subscriber Line transceivers",
ITU-T Recommendation G.993.1,
June 2004, <http://www.itu.int/
rec/T-REC-G.993.1/en>.
<http://datatracker.ietf.org/wg/adslmib/charter/>.

[AF-PHY-0086]
ATM Forum, "Inverse Multiplexing for ATM (IMA)
Specification Version 1.1", ATM Forum specification af-
phy-0086.001, March 1999, <http://www.broadband-forum.org/
ftp/pub/approved-specs/af-phy-0086.001.pdf>.

[G.994.1] ITU-T, "Handshake procedures for digital subscriber line
(DSL) transceivers", ITU-T Recommendation G.994.1,
February 2007, <http://
www.itu.int/rec/T-REC-G.994.1/en>.
June 2012, <http://www.itu.int/rec/T-REC-G.994.1/en>.

[G.998.1] ITU-T, "ATM-based multi-pair bonding", ITU-T
Recommendation G.998.1, January 2005, <http://www.itu.int/
rec/T-REC-G.998.1/en>.
<http://www.itu.int/rec/T-REC-G.998.1/en>.

[G.998.2] ITU-T, "Ethernet-based multi-pair bonding", ITU-T
Recommendation G.998.2, January 2005, <http://www.itu.int/
rec/T-REC-G.998.2/en>.
<http://www.itu.int/rec/T-REC-G.998.2/en>.

[G.998.3] ITU-T, "Multi-pair bonding using time-division inverse
multiplexing", ITU-T Recommendation G.998.3, January 2005, <http://www.itu.int/
rec/T-REC-G.998.3/en>.

[I-D.ietf-adslmib-gbond-atm-mib] Beili, E., "ATM-based xDSL Bonded
Interfaces MIB", draft-ietf-
adslmib-gbond-atm-mib-06 (work in
progress), March 2012.

[I-D.ietf-adslmib-gbond-eth-mib] Beili, E. and M. Morgenstern,
"Ethernet-based xDSL Bonded
Interfaces MIB", draft-ietf-
adslmib-gbond-eth-mib-07 (work in
progress), July 2012.

[I-D.ietf-adslmib-gbond-tdim-mib] Beili, E., "TDIM-based xDSL Bonded
Interfaces MIB", draft-ietf-
adslmib-gbond-tdim-mib-08 (work in
progress), March 2012.
<http://www.itu.int/rec/T-REC-G.998.3/en>.

[IANAifType-MIB]
Internet Assigned Numbers Authority (IANA), "IANAifType
Textual Convention definition", <h
ttp://www.iana.org/assignments/
ianaiftype-mib>.
<http://www.iana.org/assignments/ianaiftype-mib>.

[RFC2790] Waldbusser, S. and P. Grillo, "Host Resources MIB",
RFC 2790, March 2000.

[RFC2864] McCloghrie, K. and G. Hanson, "The Inverted Stack Table
Extension to the Interfaces Group MIB", RFC 2864,
June 2000.

[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Internet-
Standard Management Framework", RFC 3410, December 2002.

[RFC3440] Ly, F. and G. Bathrick, "Definitions of Extension Managed
Objects for Asymmetric Digital Subscriber Lines",
RFC 3440, December 2002.

[RFC3593] Tesink, K., "Textual Conventions for MIB Modules Using
Performance History Based on 15 Minute Intervals",
RFC 3593, September 2003.

[RFC3728] Ray, B. and R. Abbi, "Definitions of Managed Objects for
Very High Speed Digital Subscriber Lines (VDSL)",
RFC 3728, February 2004.

[RFC4181] Heard, C., "Guidelines for Authors and Reviewers of MIB
Documents", BCP 111, RFC 4181, September 2005.

[RFC4319] Sikes, C., Ray, B., and R. Abbi, "Definitions of Managed
Objects for High Bit-Rate DSL - 2nd generation (HDSL2) and
Single-Pair High-Speed Digital Subscriber Line (SHDSL)
Lines", RFC 4319, December 2005.

[RFC4706] Morgenstern, M., Dodge, M., Baillie, S., and U. Bonollo,
"Definitions of Managed Objects for Asymmetric Digital
Subscriber Line 2 (ADSL2)", RFC 4706, November 2006.

[RFC5066] Beili, E., "Ethernet in the First Mile Copper (EFMCu)
Interfaces MIB", RFC 5066, November 2007.

[RFC5591] Harrington, D. and W. Hardaker,
"Transport Security Model for the
Simple Network Management Protocol
(SNMP)", RFC 5591, June 2009.

[RFC5592] Harrington, D., Salowey, J., and
W. Hardaker, "Secure Shell
Transport Model for the Simple
Network Management Protocol
(SNMP)", RFC 5592, June 2009.

[RFC5650] Morgenstern, M., Baillie, S., and U. Bonollo, "Definitions
of Managed Objects for Very High Speed Digital Subscriber
Line 2 (VDSL2)", RFC 5650, September 2009.

[RFC5905] Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network
Time Protocol Version 4: Protocol and Algorithms
Specification", RFC 5905, June 2010.

[RFC6353] Hardaker, W., "Transport Layer
Security (TLS) Transport Model for
the Simple Network Management
Protocol (SNMP)", RFC 6353,
July 2011.

[af-phy-0086] ATM Forum, "Inverse

[RFC6766] Beili, E., "xDSL Multi-Pair Bonding Using Time-Division
Inverse Multiplexing
for ATM (IMA) Specification
Version 1.1", ATM Forum
specification af-pfy-0086.001,
March 1999.

URIs

[1] <http://www.iana.org/> (G.Bond/TDIM) MIB", RFC 6766,
February 2013.

[RFC6767] Beili, E. and M. Morgenstern, "Ethernet-Based xDSL Multi-
Pair Bonding (G.Bond/Ethernet) MIB", RFC 6767,
February 2013.

[RFC6768] Beili, E., "ATM-Based xDSL Bonded Interfaces MIB",
RFC 6768, February 2013.

Authors' Addresses

Edward Beili
Actelis Networks
25 Bazel St.
Petach-Tikva 49103
Israel

Phone: +972-3-924-3491
EMail: edward.beili@actelis.com

Moti Morgenstern
ECI Telecom
30 Hasivim St.
Petach-Tikva 4951169
Israel

Phone: +972-3-926-6258
EMail: moti.morgenstern@ecitele.com