wdiff rfc6845.original rfc6845.txt

Network Working Group
Internet Engineering Task Force (IETF) N. Sheth
Internet-Draft
Request for Comments: 6845 Contrail Systems
Updates: 2328, 5340 (if approved) L. Wang
Intended status:
Category: Standards Track J. Zhang
Expires: April 20, 2013
ISSN: 2070-1721 Juniper Networks
October 17, 2012
January 2013

OSPF Hybrid Broadcast and P2MP Point-to-Multipoint Interface Type
draft-ietf-ospf-hybrid-bcast-and-p2mp-06.txt

Abstract

This document describes a mechanism to model a broadcast network as a
hybrid of broadcast and point-to-multipoint networks for purposes of
OSPF operation. Neighbor discovery and maintenance as well as Link
State Advertisement (LSA) database synchronization are performed
using the broadcast model, but the network is represented using the
point-to-multipoint model in the router LSAs router-LSAs of the routers connected
to it. This allows an accurate representation of the cost of
communication between different routers on the network, while
maintaining the network efficiency of broadcast operation. This
approach is relatively simple and requires minimal changes to OSPF.

This document updates both OSPFv2 [RFC2328] (RFC 2328) and OSPFv3 [RFC5340]. (RFC 5340).

Status of this This Memo

This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents an Internet Standards Track document.

This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.

Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on April 20, 2013.
http://www.rfc-editor.org/info/rfc6845.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2
2. Requirements Language . . . . . . . . . . . . . . . . . . . . 4 . 3
3. Motivation . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3
4. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . 4
4.1. Interface Parameters . . . . . . . . . . . . . . . . . . . 6 4
4.2. Neighbor Data Structure . . . . . . . . . . . . . . . . . 6 . 4
4.3. Neighbor Discovery and Maintenance . . . . . . . . . . . . 6 4
4.4. Database Synchronization . . . . . . . . . . . . . . . . . 6 4
4.5. Generating Network LSAs Network-LSAs . . . . . . . . . . . . . . . . . 6 . 4
4.6. Generating Router and Intra-Area-Prefix-LSAs . . . . . . . 7 5
4.6.1. Stub Links in OSPFv2 Router LSA Router-LSA . . . . . . . . . . . 7 . 5
4.6.2. OSPFv3 Intra-Area-Prefix-LSA . . . . . . . . . . . . . 7 5
4.7. Next-Hop Calculation . . . . . . . . . . . . . . . . . . . 7 5
4.8. Graceful Restart . . . . . . . . . . . . . . . . . . . . . 8 6
5. Compatibility Considerations . . . . . . . . . . . . . . . . . 9 6
6. Scalability and Deployment Considerations . . . . . . . . . . 10 . 6
7. Management Considerations . . . . . . . . . . . . . . . . . . 11 . 7
8. Security Considerations . . . . . . . . . . . . . . . . . . . 12
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 13
10. 7
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 14
11. 7
10. Normative References . . . . . . . . . . . . . . . . . . . . . 15
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 16 7

1. Introduction

OSPF [RFC2328] operation on broadcast interfaces takes advantage of
the broadcast capabilities of the underlying medium for doing
neighbor discovery and maintenance. Further, it uses a Designated
Router (DR) and Backup Designated Router (BDR) to keep the LSA Link State
Advertisement (LSA) databases of the routers on the network
synchronized in an efficient manner. However, it has the limitation
that a router cannot advertise different costs to each of the
neighboring routers on the network in its router LSA. router-LSA.

Consider a radio network that supports true broadcast, yet the
metrics between different pairs of terminals could be different for
various reasons (e.g. (e.g., different signal strength due to placement).
When running OSPF over the radio network, for a router to advertise
different costs to different neighbors, the interface must be treated
as point-to-multipoint, point-to-multipoint (P2MP), even though the network has true
broadcast capability.

Operation on point-to-multipoint interfaces could require explicit
configuration of the identity of neighboring routers. It also
requires the router to send separate hellos Hellos to each neighbor on the
network. Further, it mandates establishment of adjacencies to all
configured or discovered neighbors on the network. However, it gives
the routers the flexibility to advertise different costs to each of
the neighboring routers in their router LSAs. router-LSAs.

This document proposes a new interface type that can be used on
networks that have broadcast capability. In this mode, neighbor
discovery and maintenance, as well as database synchronization are
performed using existing procedures for broadcast mode. The network
is modeled as a collection of point-to-point links in the router LSA, router-LSA,
just as it would be in point-to-multipoint mode. This new interface
type is referred to as hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP in the rest of this
document.

2. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].

3. Motivation

There are some networks that are broadcast capable but have a
potentially different cost associated with communication between any
given pair of nodes. The cost could be based on the underlying
topology as well as various link quality metrics such as bandwidth,
delay
delay, and jitter, among others.

It is not accurate to treat such networks as OSPF broadcast networks
since that does not allow a router to advertise a different cost to
each of the other routers. Using OSPF point-to-multipoint mode would
satisfy the requirement to correctly describe the cost to reach each
router. However, it would be inefficient in the sense that it would
require forming O(N^2) adjacencies when there are N routers on the
network.

It is advantageous to use the hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP type for such
networks. This combines the flexibility of point-to-multipoint type
with the advantages and efficiencies of broadcast interface type.

4. Operation

OSPF routers supporting the capabilities described herein should have
support for an additional hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP type for the Type
data item described in section Section 9 of [RFC2328].

The following sub-sections describe salient aspects of OSPF operation
on routers configured with a hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP interface.

4.1. Interface Parameters

The "Router Priority" interface parameter as specified in OSPFv2
[RFC2328] and OSPFv3 [RFC5340] applies to a hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP
interface.

The "LinkLSASuppression" interface parameter as specified in OSPFv3
[RFC5340] applies to a hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP interface. The
default value is "disabled". It may be set to "enabled" via
configuration.

4.2. Neighbor Data Structure

An additional field called the Neighbor Output Cost is added to the
neighbor data structure. This is the cost of sending a data packet
to the neighbor, expressed in the link state metric. The default
value of this field is the Interface output cost. It may be set to a
different value using mechanisms which that are outside the scope of this
document, like static per-neighbor configuration, or any dynamic
discovery mechanism that is supported by the underlying network.

4.3. Neighbor Discovery and Maintenance

Routers send and receive Hellos so as to perform neighbor discovery
and maintenance on the interface using the procedures specified for
broadcast interfaces in [RFC2328] and [RFC5340].

4.4. Database Synchronization

Routers elect a DR and BDR for the interface and use them for initial
and ongoing database synchronization using the procedures specified
for broadcast interfaces in [RFC2328] and [RFC5340].

4.5. Generating Network LSAs Network-LSAs

Since a hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP interface is described in router router-
LSAs using a collection of point-to-point links, the DR MUST NOT
generate a network LSA network-LSA for the interface.

4.6. Generating Router and Intra-Area-Prefix-LSAs

Routers describe the interface in their router LSA router-LSA as specified for a
point-to-multipoint interface in section Section 12.4.1.4 of [RFC2328] and
section
Section 4.4.3.2 of [RFC5340], with the following modifications for
Type 1 links:

o If a router is not the DR, it MUST NOT add any Type 1 links if it DR and does not have a full adjacency to
the DR. DR, it MUST NOT add any Type 1 links.

o If a router is not the DR and has a full adjacency to the DR, and
both the DR and this router agree on the DR role, it MUST add a
Type 1 link corresponding to each neighbor that is in state 2-Way
or higher and to which the DR's router LSA router-LSA includes a link.

o The cost for a Type 1 link corresponding to a neighbor SHOULD be
set to the value of the Neighbor Output Cost field as defined in
Section 4.2 4.2.

4.6.1. Stub Links in OSPFv2 Router LSA Router-LSA

Routers MUST add a Type 3 link for their own IP address to the router
LSA
router-LSA as described in section Section 12.4.1.4 of [RFC2328]. Further,
they MUST also add a Type 3 link with the Link ID set to the IP
subnet address, Link Data set to the IP subnet mask, and cost equal
to the configured output cost of the interface.

4.6.2. OSPFv3 Intra-Area-Prefix-LSA

Routers MUST add global globally scoped IPv6 addresses on the interface to
the intra-area-prefix-LSA as described for point-to-multipoint
interfaces in section Section 4.4.3.9 of [RFC5340]. In addition, they MUST
also add all
global globally scoped IPv6 prefixes on the interface to the
LSA by specifying the PrefixLength, PrefixOptions, and Address Prefix
fields. The Metric field for each of these prefixes is set to the
configured output cost of the interface.

The DR MUST NOT generate an intra-area-prefix-LSA for the transit
network for this interface since it does not generate a network LSA network-LSA
for the interface. Note that the global prefixes associated with the
interface are advertised in the intra-area-prefix-LSA for the router
as described above.

4.7. Next-Hop Calculation

Next-Hops

Next-hops to destinations that are directly connected to a router via
the interface are calculated as specified for a point-to-multipoint
interface in section Section 16.1.1 of [RFC2328].

4.8. Graceful Restart

The following modifications to the procedures defined in section Section 2.2,
item 1 1, of [RFC3623] are required in order to ensure that the router
correctly exits graceful restart.

o If a router is the DR on the interface, the pre-restart network network-
LSA for the interface MUST NOT be used to determine the previous
set of adjacencies.

o If a router is in state DROther on the interface, an adjacency to
a non-DR or non-BDR neighbor is considered as reestablished when
the neighbor state reaches 2-Way.

5. Compatibility Considerations

All routers on the network must support the hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP
interface type for successful operation. Otherwise, the interface
should be configured as a standard broadcast interface.

If some routers on the network treat the interface as broadcast and
others as hybrid-broadcast-and-p2mp, hybrid-broadcast-and-P2MP, neighbors and adjacencies will
still get formed as for a broadcast interface. However, due to the
differences in how router and network LSAs network-LSAs are built for these two
interface types, there will be no traffic traversing certain pairs of
routers. Note that this will not cause any persistent loops or black
holing
black-holing of traffic.

To detect and flag possible mismatched configurations, an
implementation of this specification SHOULD log a message if a
Network LSA
network-LSA is received for a locally configured hybrid interface.

6. Scalability and Deployment Considerations

Treating a broadcast interface as hybrid-broadcast-and-p2mp hybrid-broadcast-and-P2MP results
in O(N^2) links to represent the network instead of O(N), when there
are N routers on the network. This will increase memory usage and
have a negative impact on route calculation performance on all the
routers in the area. Network designers should carefully weigh the
benefits of using the new interface type against the disadvantages
mentioned here.

7. Management Considerations

The following MIB variable/value should be added to the appropriate
OSPFv2 and OSPFv3 MIBs ([RFC4750], [RFC5643]).

o For ospfIfType/ospfv3IfType, a new value broadcast-p2mp-hybrid broadcast-P2MP-hybrid (X)
for the hybrid interface type (X to be defined when the revised
MIB documents are approved).

o For ospfNbrEntry/ospfv3NbrEntry, an ospfNbrMetricValue/
ospfv3NbrMetricValue attribute for per-neigbhor per-neighbor metrics. In case
of non-hybrid interfaces, the value is the same as the interface
metric.

This section is not normative.

8. Security Considerations

This document raises no new security issues for OSPF. Security
considerations for the base OSPF protocol are covered in [RFC2328],
[RFC5340], and [RFC6506].

9. IANA Considerations

This document has no IANA considerations.

This section should be removed by the RFC Editor to final
publication.

10. Acknowledgements

The authors would like to thank Acee Lindem and Richard Ogier for
their comments and suggestions.

11.

10. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.

[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.

[RFC5340] Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
for IPv6", RFC 5340, July 2008.

[RFC3623] Moy, J., Pillay-Esnault, P., and A. Lindem, "Graceful OSPF
Restart", RFC 3623, November 2003.

[RFC4750] Joyal, D., Galecki, P., Giacalone, S., Coltun, R., and F.
Baker, "OSPF Version 2 Management Information Base",
RFC 4750, December 2006.

[RFC5340] Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
for IPv6", RFC 5340, July 2008.

[RFC5643] Joyal, D. and V. Manral, "Management Information Base for
OSPFv3", RFC 5643, August 2009.

[RFC6506] Bhatia, M., Manral, V., and A. Lindem, "Supporting
Authentication Trailer for OSPFv3", RFC 6506,
February 2012.

Authors' Addresses

Nischal Sheth
Contrail Systems
2350 Mission College Blvd, #1140
Santa Clara, CA 95054
US

Email:

EMail: nsheth@contrailsystems.com

Lili Wang
Juniper Networks
10 Technology Park Dr.
Westford, MA 01886
US

Email:

EMail: liliw@juniper.net

Jeffrey Zhang
Juniper Networks
10 Technology Park Dr.
Westford, MA 01886
US

Email:

EMail: zzhang@juniper.net