Network Working Group
Internet Engineering Task Force (IETF) B. Liu
Internet Draft
Request for Comments: 7010 S. Jiang
Intended status:
Category: Informational Huawei Technologies Co., Ltd
Expires: December 11, 2013 Ltd.
ISSN: 2070-1721 B. Carpenter
University of Auckland
S. Venaas
Cisco Systems
W. George
Time Warner Cable
June 9,
August 2013
IPv6 Site Renumbering Gap Analysis
draft-ietf-6renum-gap-analysis-08.txt
Abstract
This document briefly introduces the existing mechanisms that could
be utilized for IPv6 site renumbering and tries to cover most of the
explicit issues and requirements of associated with IPv6 renumbering. Its main
The content is mainly a gap analysis that provides a basis for future
works to identify and develop solutions or to stimulate such
development as appropriate. The gap analysis is organized by the
main steps of a renumbering process.
Status of this This Memo
This Internet-Draft document is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute working
documents as Internet-Drafts. The list It represents the consensus of current Internet-Drafts is
at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a maximum candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 11, 2013.
http://www.rfc-editor.org/info/rfc7010.
Copyright Notice
Copyright (c) 2012 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ................................................. 4 ....................................................4
2. Overall Requirements for Renumbering ......................... 4 ............................4
3. Existing Components for IPv6 Renumbering ..................... 5 ........................5
3.1. Relevant Protocols and Mechanisms ....................... 5 ..........................5
3.2. Management Tools ........................................ 6 ...........................................6
3.3. Procedures/Policies ..................................... 7 Procedures and Policies ....................................7
4. Managing Prefixes ............................................ 7 ...............................................7
4.1. Prefix Delegation ....................................... 7 ..........................................7
4.2. Prefix Assignment ....................................... 8 ..........................................8
5. Address Configuration ........................................ 8 ...........................................8
5.1. Host Address Configuration .............................. 8 .................................8
5.2. Router Address Configuration ............................ 9 ...............................9
6. Updating Address-relevant Address-Relevant Entries ........................... 10 ..............................10
6.1. DNS Records Update ..................................... 10 ........................................10
6.2. In-host In-Host Server Address Update .......................... 11 .............................11
6.3. Address update Update in scattered configurations ............. 11 Scattered Configurations ................11
7. Renumbering Event Management ................................ 13 ...................................13
7.1. Renumbering Notification ............................... 13 ..................................13
7.2. Synchronization Management ............................. 14 ................................14
7.3. Renumbering Monitoring ................................. 14 ....................................15
8. Miscellaneous ............................................... 14 ..................................................15
8.1. Multicast .............................................. 14 .................................................15
8.2. Mobility ............................................... 16 ..................................................17
9. Gap Summary ................................................. 17 ....................................................17
9.1. Managing Prefixes ...................................... 17 .........................................17
9.2. Address configuration .................................. 17 Configuration .....................................17
9.3. Address relevant entries update ........................ 17 Address-Relevant Entries Update ...........................18
9.4. Renumbering event management ........................... 18 Event Management ..............................19
9.5. Miscellaneous .......................................... 19 .............................................19
10. Gaps considered unsolvable ................................. 19 Considered Unsolvable ....................................20
10.1. Address Configuration ................................. 19 ....................................20
10.2. Address-relevant Address-Relevant Entries Update ....................... 19 ..........................20
10.3. Miscellaneous ......................................... 20 ............................................21
11. Security Considerations .................................... 20 .......................................21
12. IANA Considerations......................................... 21
13. Acknowledgments ............................................ 21
14. ...............................................22
13. References ................................................. 22
14.1. ....................................................23
13.1. Normative References .................................. 22
14.2. .....................................23
13.2. Informative References ................................ 23 ...................................23
1. Introduction
As introduced in [RFC5887], renumbering, especially for medium to
large sites and networks, is currently viewed as an expensive,
painful, expensive and
painful. This error-prone process, process is avoided by network managers as
much as possible. If IPv6 site renumbering continues to be
considered difficult, network managers will turn to Provider
Independent (PI) addressing for IPv6 to as an attempt to minimize the
need for future renumbering. However, widespread use of PI
addressing may create very serious BGP4 scaling problems [RFC4984].
It is thus desirable to develop tools and practices that may make
renumbering a simpler process to
reduce and reduces demand for IPv6 PI space.
Building upon the IPv6 enterprise renumbering scenarios described in
[RFC6879], this document performs a gap analysis to provide a basis
for future work to identify and develop solutions or to stimulate
such development as appropriate. The gap analysis is organized
according to the main steps of a renumbering process, which include includes
prefix management, node address (re)configuration, and updating updates to
address-relevant entries in various devices such as firewalls,
routers and servers, etc. Renumbering event management is presented
independently from the steps of a renumbering process, process in order to
identify some operational and administrative gaps in renumbering.
This document starts from existing work in [RFC5887] and [RFC4192].
It does further analysis analyzes and identifies the valuable and solvable issues,
digs out of some undiscovered gaps, and gives some solution
suggestions. This document considers the make-before-break approach
as a premise for the gap analysis, so readers should be familiar with
[RFC4192].
Renumbering nodes with static addresses has a particular set of
problems, thus discussion of that space has been covered in a related
document [RFC6866].
This document does not cover the un-planned unplanned emergency renumbering
cases.
2. Overall Requirements for Renumbering
This section introduces the overall goals we want to achieve in of a renumbering event. In
general, we need to leverage renumbering automation to avoid human
intervention as much as possible at a reasonable cost. Some existing
mechanisms have already provided provide useful ability.
The automation can be divided into four aspects as follows.
(Detailed analysis of the four aspects is presented respectively in section
Sections 4
to section through 7.)
o Prefix delegation and delivery should be automatic and accurate in
aggregation and coordination.
o Address reconfiguration should be automatically achieved through
standard protocols with minimum human intervention.
o Address-relevant entry updates should be performed together and
without error.
o Renumbering event management is needed to provide the functions of
renumbering notification, synchronization, and monitoring.
Besides automation, session survivability is another important issue
during renumbering since application outage is one of the most
obvious impacts that make renumbering painful and expensive. Session
survivability is a fundamental issue that cannot be solved within a
renumbering context only. However, with the [RFC4192] make-before-
break make-before-break
approach, and which uses the address lifetime mechanisms in IPv6
Stateless Address Autoconfiguration (SLAAC) and Dynamic Host
Configuration Protocol for IPv6 (DHCPv6), allows for a smooth
transition mechanism from old to new prefixes is applicable. prefixes. In most of the cases, since
we can set the transition period to be long enough to cover the on-going
ongoing sessions, we consider this mechanism sufficient for
avoiding session brokenness issue to avoid
broken sessions in IPv6 site renumbering. (Please note that if
multiple addresses are running simultaneously on hosts, hosts simultaneously, the address
selection [RFC6724] needs to be carefully handled.)
3. Existing Components for IPv6 Renumbering
Since renumbering is not a new issue, some protocols and mechanisms
have already been utilized for renumbering. this purpose. There were are also some
dedicated protocols and mechanisms that have been developed for
renumbering. This section briefly reviews these existing protocols
and mechanisms to provide a basis for the gap analysis.
3.1. Relevant Protocols and Mechanisms
o RA Router Advertisement (RA) messages, defined in [RFC4861], are used
to deprecate/announce
old/new deprecate prefixes that are old or announce prefixes that are
new, and to advertise the availability of an upstream router. In
renumbering, it RA is one of the basic mechanisms for host
configuration.
o When renumbering a host, SLAAC [RFC4862] may be used for address
configuration with the new prefix(es). Hosts receive RA messages
which
that contain routable prefix(es) and the address(es) of the
default router(s), router(s); then hosts can generate IPv6 address(es) by
themselves.
o Hosts that are configured through DHCPv6 [RFC3315] obtain new
addresses through the renewal process or when they receive the
reconfiguration messages initiated by the DHCPv6 servers.
o DHCPv6-PD (Prefix Delegation) [RFC3633] enables automated
delegation of IPv6 prefixes using the DHCPv6.
o [RFC2894] defined defines standard ICMPv6 messages for router renumbering.
This is a dedicated protocol for renumbering, but we are not aware
of it being used in real network deployment.
3.2. Management Tools
Some renumbering operations could be automatically processed by
management tools in order to make the renumbering process more
efficient and accurate. The tools may be designed specifically for
renumbering, or common tools could be utilized for some of the
renumbering operations.
Following are examples of these tools. tools:
o IP address management (IPAM) tools. There are both commercial and
open-source solutions. IPAM tools are used to manage IP address
plans,
plans and usually integrate the DHCPv6 and DNS services together
as a whole solution. Many mature commercial tools can support
management operations, but normally they do not have dedicated
renumbering functions. However, the integrated DNS/DHCPv6
services and address management function can obviously facilitate
the renumbering process.
o Third-party tools. Some organizations use third-party tools to
push configuration to devices. This is sometimes used as a
supplement to vendor specific vendor-specific solutions. A representative of such
a third-party tool is [cfengine]. [CFENGINE].
o Macros. [LEROY] proposed a mechanism of macros to automatically
update the address-relevant entries/configurations inside the DNS,
firewall, etc. The macros can be delivered though through the SOAP
protocol from a network management server to the managed devices.
o Asset management tools/systems. These tools may provide the
ability of managing to manage configuration files in nodes so that it is
convenient to update the address-relevant configuration in these
nodes.
3.3. Procedures/Policies Procedures and Policies
o [RFC4192] proposed a procedure for renumbering an IPv6 network
without a flag day. The document includes a set of operational
suggestions which that can be followed step by step by network
administrators. It should be noted that the administrators need
to carefully deal with the address selection issue issue, while the old
and new prefixes are both available during the overlapping period in
[RFC4192] procedure. And
as described in the procedures in [RFC4192]. The address
selection policies might need to be updated after renumbering. So renumbering, so
the administrator could leverage the address selection policy address-selection-policy
distribution mechanism as described in
[I-D.ietf-6man-addr-select-opt]. [6MAN-ADDR-OPT].
o [RFC6879] analyzes the enterprise renumbering events and gives the makes
recommendations among based on the existing renumbering mechanisms.
According to the different stages, renumbering considerations are
described in three categories: considerations and recommendations
during network design, for the preparation of enterprise network
renumbering, and during the renumbering operation.
4. Managing Prefixes
When renumbering an IPv6 enterprise site, the key procedural issue is
switching the old prefix (es) prefix(es) to the new one(s). A new short prefix may
be divided into longer ones for subnets. So subnets, so we need to carefully
manage the prefixes to ensure they are synchronized and coordinated
in
within the whole network.
4.1. Prefix Delegation
For big enterprises, the new short prefix(es) usually comes down
through off-line offline human communication. But But, for the SOHO style SOHO-style (Small
Office, Home Office) SMEs (Small & Medium Enterprises), the prefixes
might be dynamically received by DHCPv6 servers or routers inside the
enterprise networks. The short prefix(es) could be automatically
delegated through DHCPv6-
PD. DHCPv6-PD. Then the downlink DHCPv6 servers or
routers can could begin advertising the longer prefixes to the subnets.
The delegation routers might need to renumber themselves with the new
delegated prefixes. So So, there should be a mechanism informing to inform the
router
routers to renumber themselves by delegated prefixes; and there also should
also be a mechanism for the routers to derive addresses automatically
based on the delegated prefixes.
4.2. Prefix Assignment
When subnet routers receive the longer prefixes, they can advertise a
prefix on a link to which hosts are connected. Host address
configuration, rather than routers, is the primary concern for prefix
assignment
assignment, which is described in the following section Section 5.1.
5. Address Configuration
5.1. Host Address Configuration
o SLAAC/DHCPv6 interaction problems SLAAC and DHCPv6 Interaction Problems
Both of the DHCPv6 and Neighbor Discovery (ND) protocols have an IP address
configuration function. They function, which are suitable for different scenarios.
During renumbering, the SLAAC-configured hosts can reconfigure IP
addresses by receiving ND Router Advertisement (RA) messages
containing new prefix information. (It should be noted that, that the
prefix delivery could be achieved through DHCPv6 according to
[I.D ietf-dhc-host-gen-id]).
[PREFIX-DHCPv6]). The DHCPv6-configured hosts can reconfigure
addresses by initiating RENEW sessions [RFC3315] when the current
addresses' lease times are expired or when they receive
reconfiguration messages initiated by the DHCPv6 servers.
Sometimes the two address configuration modes may both be available in one
network. This would add additional complexity for both the hosts and the
network management.
With the flags defined in RA (ManagedFlag (M) indicating the DHCPv6
service available in the network; OtherConfigFlag (O) indicating
other configurations such as DNS/routing), the two separated address
configuration modes are correlated. However, the ND protocol did does
not define the flags as prescriptive but only as advisory. This has
led to variation in the behavior of hosts when interpreting the flags.
Different
flags; different operating systems have followed different
approaches. (For more details, please refer to [I-D.liu-bonica-dhcpv6-slaac-problem] [DHCPv6-SLAAC] and [I-D.liu-6renum-dhcpv6-slaac-switching].)
[6RENUM-SLAAC].)
The impact of ambiguous M/O flags includes the following aspects:
- DHCPv6-configured hosts might not be able to be renumbered by
RA
It is unclear whether a DHCPv6 configured DHCPv6-configured host will accept
address configuration though RA messages, especially when the M
flag
transitioning transitions from 1 to 0; this depends on the
implementation of the operating system. It might not be
possible for administrators to only use RA messages for
renumbering, since renumbering might fail on some already
DHCPv6-configured hosts. It This means administrators have to use
DHCPv6 reconfiguration for some DHCPv6-
configured DHCPv6-configured hosts. It is
not convenient convenient, and DHCPv6 reconfiguration is not suitable for
bulk usage as analyzed in below.
- DHCPv6-configured hosts might not be able to learn new RA
prefixes
[RFC5887] mentioned mentions that DHCPv6-configured hosts may want to
learn about the upstream availability of new prefixes or loss
of prior prefixes dynamically by deducing this from periodic RA
messages. Relevant standards ([RFC4862],[RFC3315]) [RFC4862] [RFC3315] are ambiguous
about what approach should be taken by a DHCPv6-configured host
when it receives RA messages containing a new prefix. Current
behavior depends on the operating system of the host and cannot
be predicted or controlled by the network.
- SLAAC-configured hosts might not be able to add a DHCPv6
address(es)
The behavior when the host receives RA messages with the M flag
set is unspecified.
The host may start a DHCPv6 session and receive the DHCPv6
address configuration, or it may just ignore the messages. If the network
side wants
Whether the hosts to start DHCPv6 configuration, it configuration is just out
of outside the
control of the network side.
5.2. Router Address Configuration
o Learning new prefixes New Prefixes
As described in [RFC5887], "if a site wanted to be multihomed using
multiple provider-aggregated (PA) routing prefixes with one prefix
per upstream provider, then the interior routers would need a
mechanism to learn which upstream providers and prefixes were
currently reachable (and valid). In this case, their Router
Advertisement messages could be updated dynamically to only advertise
currently valid routing prefixes to hosts. This would be
significantly more complicated if the various provider prefixes were
of different lengths or if the site had non-uniform subnet prefix
lengths."
o Restart after renumbering Restarting After Renumbering
As [RFC2072] mentioned, mentions, some routers cache IP addresses in some
situations, so routers might need to be restarted as a result of site
renumbering. While most modern systems support a cache-clear
function that eliminates the need for restarts, there are always
exceptions that must be taken into account.
o Router naming Naming
[RFC4192] suggests states that "To better support renumbering, switches and
routers should use domain names for configuration wherever
appropriate, and they should resolve those names using the DNS when
the lifetime on the name expires." expires". As [RFC5887] described, this
capability is not new, and currently it is present in most IPSec VPN
implementations. However, many administrators may need to be alerted
to the fact that it could can be utilized to avoid manual modification
during renumbering.
6. Updating Address-relevant Address-Relevant Entries
In conjunction with renumbering the nodes, any configuration or data
store containing previous addresses must be updated as well. Some
examples include DNS records and filters in various entities such as
ACLs
Access Control Lists (ACLs) in firewalls/gateways.
6.1. DNS Records Update
o Secure Dynamic DNS update (DDNS) Update
In real network operations, a DNS update is normally achieved by
maintaining a DNS zone file and loading this file into the site's DNS
server(s). Synchronization between host renumbering and the updating
of its A6 or AAAA record is hard. [RFC5887] mentioned that discusses an alternative is to use that
uses the Secure Dynamic DNS Update [RFC3007], in which a host informs
its own DNS server when it receives a new address.
The Secure Dynamic DNS Update has been widely supported by the major
DNS implementations, but it hasn't been widely deployed. Normal
hosts are not suitable to do the update update, mainly because of the complexity of key
management
complex key-management issues inherited from secure DNS mechanisms,
so current practices usually assign the DHCP servers to act as DNS
clients to request that the DNS server updating update relevant records
[RFC4704]. This
server-oriented approach The key-management problem is applicable tractable in the case of
updates for large numbers a limited number of hosts'
using secure DDNS. (In some commercial solutions, servers, so Dynamic DNS service updates could
be integrated with DHCP service provided by the same vendor so that
the secure DDNS might be silently enabled
serve as default.) a suitable solution for keeping server DNS records up to
date on a typical enterprise network. However, there this solution is still a gap here, since not
easily applicable to hosts in general.
To address the larger use case of arbitrary non-server hosts being
renumbered, DHCP servers have to learn that the relevant hosts have
changed their addresses and thus trigger the DDNS update. If the
hosts were numbered and also renumbered by DHCP, then it is would be easy for
the DHCP servers to learn the address changes; but however, if the hosts
were numbered by SLAAC, then there could be trouble.
[I-D.ietf-dhc-addr-registration] proposed a address registration
mechanism which could be used to address the latter issue; however,
it has not been deployed yet.
6.2. In-host In-Host Server Address Update
While DNS stores the addresses of hosts in servers, hosts are also
configured with the addresses of servers servers, such as DNS server, radius
server. and RADIUS
servers [RFC2865]. While renumbering, the hosts must update these
addresses if the server addresses changed. change.
In principle, the addresses of DHCPv6 servers do not need to be
updated,
updated since they could be dynamically discovered through DHCPv6
relevant
DHCPv6-relevant multicast messages. But in practice, most relay
agents have the alternative option of being configured with a DHCPv6 server
address rather than sending to a multicast address. So Therefore, the
DHCP server addresses update might be an issue in practice.
6.3. Address update Update in scattered configurations Scattered Configurations
Besides the DNS records and the in-host server address entries, there
are also many places in which IP addresses are configured, for
example, filters such as ACL and routing policies. There are even
more sophisticated cases where the IP addresses are used for deriving
values, for example, using the unique portion of the loopback address
to generate an ISIS net ID.
In renumbering, it is annoying and error-prone to update updating the IP addresses in all the above mentioned places.
places is burdensome and error-prone. We lack a "one-stop" mechanism
to trigger the updates for all the subsystems on a
host/server, host/server and
all the external databases that refer to the IP address update. We decompose
break the general "one-stop" gap into the following two aspects.
o Self-contained Self-Contained Configuration in Individual device
In an ideal way, the IP Devices
Ideally, IP addresses can be defined as a value once, and then the
administrators can use either keywords or variables to call the value
in other places such as a sort of internal inheritance in CLI
(command line interface) or other local configurations. This makes
it easier to manage a renumbering event by reducing the number of
places where a device's configuration must be updated. However, it
still means that every device needs to be touched, individually updated, but
only once instead of having to inspect the whole configuration to
ensure that none of the separate places that a given IP address
occurs is missed.
Among the current devices, some routers support defining multiple
loopback interfaces which that can be called in other configurations. For
example, when defining a tunnel, it can call the defined loopback
interface to use its address as the local address of the tunnel.
This can be considered as a kind of parameterized self-contained
configuration. But However, this only applies to certain use cases; it
is impossible to use the loopback interfaces to represent external
devices
devices, and it is not always possible to call loopback interfaces in
many other configurations. Parameterized self-contained
configuration is still a gap for current devices. that needs to be filled.
o Unified Configuration Management among Devices
This refers to a more formalized central configuration management
system, where all changes are made in one place place, and the system
manages how to push the changes are pushed to the individual devices. This issue
contains two aspects aspects, as the following. follows:
- Configuration Aggregation
Configuration data based on addresses or prefixes are usually
spread out in various devices. As [RFC5887] described, describes, some
address configuration data might be widely dispersed and much
harder to find, even find. Some will inevitably be found only after the
renumbering event. So Because there's a big gap for in configuration
aggregation, it is hard to get all the relevant configurations through configuration
data together in one place.
- Configuration Update Automation
As mentioned in section Section 3.2, [LEROY] proposed proposes a mechanism which that
can automatically update the configurations. The mechanism
utilizes macros suitable for various devices such as routers, firewalls. routers
and firewalls to update the configurations based on the new prefix.
Such an automation tool is valuable for renumbering because it
can reduce manual
operation operation, which is error-prone and inefficiency.
inefficient.
Besides the macros, [LEROY] also proposed to proposes the use of SOAP to
deliver the macros to the devices. As well as SOAP Along with SOAP, we may
consider whether it is possible and suitable to use other
standardized protocols protocols, such as NETCONF [RFC4714].
But in the Network Configuration
Protocol (NETCONF) [RFC6241].
In current real networks, most of the devices use vendor-
private vendor-private
protocols to update configurations, so it is not necessarily
valid to assume that there is going to be a formalized
configuration management system to leverage. Although there
are some vendor-independent tools as mentioned in section Section 3.2,
a standard and comprehensive way of to uniformly updating update
configurations in multi-vendor devices is still a big gap currently. missing.
7. Renumbering Event Management
From the perspective of network management, renumbering is a kind of an event which
that may need additional process processes to make it more easy easier and more
manageable.
7.1. Renumbering Notification
If
The process of renumbering could benefit from hosts or servers are being
made aware of an occurrence of a renumbering event happening, it
may benefit the relevant process. event. Following are
several examples of
such additional process processes that may ease the renumbering.
o A notification mechanism may be needed to indicate to hosts that a
renumbering event has changed some DNS records in DNS servers
(normally, in an enterprise it/they is/are (a) enterprise, it is a local recursive DNS
server(s).),
server(s)), and then the hosts might want to refresh the DNS
cache. That mechanism may also need to indicate that such a
change will happen at a specific time in the future.
o As suggested in [RFC4192], [RFC 4192], if the DNS service can be given prior
notice about a renumbering event, then people could reduce the delay in the transition to
new IPv6 addresses, addresses could be reduced and thus improve the
efficiency of renumbering.
o Router awareness: in In a site with multiple domains which that are
connected by border routers, all border routers should be aware of
renumbering in one domain or multiple domains, domains and update the
internal forwarding tables and the address/prefix based address-/prefix-based filters
accordingly to correctly handle inbound packets.
o Ingress filtering: ISPs normally enable an ingress filter to drop
packets with source addresses from other ISPs at the end site end-site
routers to prevent IP spoofing [RFC2827]. In a multihomed site
with multiple PA prefixes, the ingress router of ISP A should be
notified if the ISP B initiates a renumbering event in order to
properly update its filters to permit the new legitimate prefix
(es).
prefix(es). For large enterprises, it might be applicable practical to indicate
manage this new legitimate prefix information through human communication,
however,
communication. However, for the millions of small enterprises, an
automated notification mechanism is needed.
o Log collectors: In the NMS (network management system), logs
collected through syslog, SNMP notification, IPFIX, etc. usually
treat the UDP message source IP addresses as the host or router
IDs. When one source IP address is changed, the log collectors
will consider that a new device appeared in the network. So
Therefore, a mechanism is needed for the NMS applications to learn
the renumbering event, event including the mappings of old and new IP
address for each host/router, so that they could correlate update the old and new addresses
address-relevant mappings as described in the logs. Section 7.2.
7.2. Synchronization Management
o DNS update synchronization Update Synchronization
The DNS changes must be coordinated with the changes of node address
configuration. configuration
changes. DNS has a latency issue of propagating information from the
server to the resolver. The latency is mainly caused by TTL the Time to
Live (TTL) assigned to individual DNS records and the timing of
updates from primary to secondary servers [RFC4192].
Ideally, during a renumbering operation, the DNS TTLs should always
be shorter than any other lifetime lifetimes associated with an address. If
the TTLs were set correctly, then the DNS latency could be well
controlled. However, there might be some exceptional situations in
which the DNS TTLs were already set too long for the time available
to plan and execute a renumbering event. In these situations, there
currently
are currently no mechanisms to deal with the already configured long
DNS TTLs.
o NMS Address-Relevant Mapping Synchronization
In the NMS, logs collected through syslog, SNMP notification, IPFIX,
etc. usually treat the UDP message source IP addresses as the host or
router IDs. When one source IP address is renumbered, the log
collectors will consider that a new device appeared in the network.
Therefore, the NMS needs to learn the renumbering event and thus
correlate the old and new address in the logs.
If the NMS applies unique IDs for the hosts or routers, then the
mappings between the unique IDs and IP addresses also need to be
updated after renumbering.
7.3. Renumbering Monitoring
While treating renumbering as a network event, mechanisms to monitor
the renumbering process might be needed to inform the administrators
whether the renumbering has been successfully done. successful. Considering that the
address configuration operation might be stateless (if ND is used for
renumbering), it is difficult for monitoring. to monitor.
8. Miscellaneous
Since multicast and mobility are special use cases which that might not be
included in routine/common routine or common renumbering operations, they are
separately
discussed as miscellaneous separately in this miscellaneous section.
8.1. Multicast
In
From the perspective of interface renumbering operations, renumbering
a multicast address is the same with as renumbering a unicast address. So
this section mainly discusses the issues from the perspective of the
impact to the multicast application systems caused by renumbering.
Renumbering also has an impact on multicast. Renumbering of unicast
addresses affects multicast even if the multicast addresses are not
changed. There may also be cases where the multicast addresses need
to be renumbered.
o Renumbering of multicast sources Multicast Sources
If a host that is a multicast source is renumbered, the application
on the host may need to be restarted for it to successfully send
packets with the new source address.
For ASM (Any-Source Multicast) Multicast), the impact on a receiver is that a
new source appears to start sending, sending and it no longer receives from
the previous source. Whether this is an issue depends on the
application, but we believe it is likely to not to be a major issue.
For SSM (Source-Specific Multicast) however, there is one significant
problem. The receiver needs to learn which source addresses it must
join. Some applications may provide their own method for learning
sources, where the source application may somehow signal the
receiver.
Otherwise, the receiver may e.g. may, for example, need to get new SDP
(Session Description Protocol) information with the new source
address. This is similar to how to learn the process for learning a new group
address,
address; see the "Renumbering of multicast addresses" Multicast Addresses" topic below.
o Renumbering of Rendezvous-Point
If the unicast addresses of routers in a network are renumbered, then
the RP (Rendezvous-Point) address is also likely to change for at
least some groups. An RP address is needed by PIM-SM for providing
ASM, (Protocol
Independent Multicast - Sparse Mode) to provide ASM and for Bidir
PIM. Changing the RP address is not a major issue, except that the
multicast service may be impacted while the new RP addresses are
configured. If dynamic protocols are used for
distributing to distribute group-to-RP
mappings, the change can be fairly quick, quick and any impact time should
be only for a very brief time. brief. However, if routers are statically configured, this the
time impacted depends on how long it takes to update all the
configurations.
For PIM-SM PIM-SM, one typically switches to SPT (Shortest-Path-Tree) when
the first packet is received by the last-hop routers. Forwarding on
the SPT should not be impacted by the change of IP address. Network A
network operator should be careful not to deprecate the previous
mapping before configuring a new one, because implementations may
revert to Dense Mode if no RP is configured.
o Renumbering of multicast addresses Multicast Addresses
In general general, multicast addresses can be chosen independently of the
unicast addresses, and the multicast addresses can remain fixed even
if the unicast addresses are renumbered. However, for IPv6 IPv6, there
are useful ways of deriving multicast addresses from unicast
addresses, such as unicast-prefix-based described in "Unicast-Prefix-based IPv6 Multicast Addresses
Addresses" [RFC3306] and
Embedded-RP "Embedded-RP IPv6 Multicast Addresses Addresses"
[RFC3956]. In that case those cases, the multicast addresses used may have to
be renumbered.
Renumbering group addresses may be complicated. For multicast, it is
common to use literal addresses, addresses and not DNS. When multicast
addresses are changed, source applications need to be reconfigured
and restarted.
Multicast receivers need to learn the new group addresses to join.
Note that for SSM, receivers need to learn which multicast channels
to join. A channel is a source and group pair. This means that for
an SSM application, a change of source address is likely to have the
same effect as a change of group address.
Some applications may have dynamic methods of learning which groups
(and possibly sources) to join. If not, the application may have to
be reconfigured and restarted.
One common way for receivers to learn the necessary parameters is by
use of SDP. SDP information may be distributed via various
application protocols, protocols or it may be from a file. An SDP file may be distributed
via HTTP, email email, etc. If a user is using a web browser and clicking
on a link to launch the application with the necessary data, it may
be a matter of closing the current application, application and re-
clicking re-clicking the
link.
In summary, currently the currently, multicast renumbering issues are basically
handled by application-specific methods. There is no standard way to
guarantee that multicast service could live across a renumbering
event.
8.2. Mobility
As described in [RFC5887], if a mobile node's home address changes
unexpectedly, the node can be informed of the new global routing
prefix used at the home site through the Mobile Prefix Solicitation
and Mobile Prefix Advertisement ICMPv6 messages [RFC6275]. But However,
if the mobile node is unfortunately disconnected at the time of home address
renumbering, it will no longer know a valid subnet anycast address
for its home agent, leaving it to deduce a valid address on the basis
of DNS information.
So, for Mobile IP, we need a better mechanism to handle the change of
home agent address while the mobile address is disconnected.
9. Gap Summary
The following is a summary of the gaps identified previously in this
document that are considered solvable, but may require process or
protocol changes to resolve.
9.1. Managing Prefixes
o A mechanism informing the router routers to renumber themselves by
delegated prefixes prefixes.
o A mechanism for the routers to derive addresses automatically
based on the delegated prefixes.
9.2. Address configuration Configuration
o Host address configuration Address Configuration
- DHCPv6-configured hosts might not be able to be renumbered by
RA on some of current implementations implementations.
- DHCPv6-configured hosts might not be able to learn new RA
prefixes on some of current implementations implementations.
- SLAAC-configured hosts might not be able to add DHCPv6
address(es) on some of current implementations implementations.
o Router address configuration Address Configuration
- A mechanism for interior routers in a multihomed site to learn
which upstream providers and prefixes were are currently reachable reachable.
- Cache-clear might need to restart (rarely in modern routers) routers).
- Using Use of router domain names is not widely learned/deployed learned or deployed by
administrators
administrators.
9.3. Address relevant entries update Address-Relevant Entries Update
o DNS records update Records Update
- For key management key-management scalable issue, issues, secure dynamic DNS update
is usually done by DHCP servers on behalf of the hosts, so it
might not be applicable practical for SLAAC-configured hosts to do secure
DDNS.
o In-host server address update In-Host Server Address Update
- DHCP relays might be configured with DHCP server addresses
rather than by sending multicast messages to discover the DHCP
server dynamically, so updating the DHCP server addresses update might
be an issue in practice.
o Address update Update in scattered configurations Scattered Configurations
- Devices For devices that don't support parameterized configuration,
administrators
need to touch every places where individually update all devices in which IP
addresses were configured
previously configured.
- It is hard to get all the address-relevant configurations
spread in various devices through one place place.
- Uniformly update updating configurations in multi-vendor devices is
currently a
big gap currently that needs to be filled.
9.4. Renumbering event management Event Management
o Renumbering notification Notification
- A mechanism to indicate hosts a host's local recursive DNS is going
to be
renumbered renumbered.
- A prior notice about a renumbering event for DNS DNS.
- A mechanism for border routers to know internal partial
renumbering
renumbering.
- For multihomed sites, a mechanism is needed to notify the
egress router of
ISPA connecting to ISP A that the egress router
connecting to ISPB initiates renumbering
is needed. ISP B has initiated renumbering.
- A mechanism is needed for the NMS applications to learn the
renumbering event, so that they could correlate the old and new
addresses in the logs. logs, and update the unique ID of the device
and address mappings.
o Synchronization management Management
- DNS information propagating the latency issue issue.
- Mechanisms are needed for the NMS applications to correlate the
old and new addresses in logs and to update the unique ID of
the device and address mappings.
o Renumbering monitoring Monitoring
- Mechanisms to monitor the process and feedback of renumbering
might be needed.
9.5. Miscellaneous
o Multicast
- Mechanism A mechanism for SSM receivers to learn the source addresses
when multicast sources are renumbered.
o Mobility
- A better mechanism to handle a change of home agent address
while the mobile address is disconnected.
10. Gaps considered unsolvable Considered Unsolvable
This section lists gaps that have been identified by other documents
but are considered unsolvable.
10.1. Address Configuration
o RA prefix lifetime limitation
In section Prefix Lifetime Limitation
Section 5.5.3 of [RFC4862], it is defined that [RFC4862] states "If the received Valid Lifetime is
greater than 2 hours or greater than RemainingLifetime, set the valid
lifetime of the corresponding address to the advertised Valid
Lifetime." So when renumbering, if the previous RemainingLifetime is
longer than two hours, it is impossible to reduce a prefix's lifetime
to less than two hours. This limitation is to prevent denial-of-service attack. denial-of-
service attacks.
10.2. Address-relevant Address-Relevant Entries Update
o DNS authority Authority
In an enterprise that hosts servers on behalf of collaborators and
customers, it is often the case that DNS zones outside the
administrative control of the hosting enterprise maintain resource
records concerning addresses for hosted nodes within its address
space. When the hosting enterprise renumbers, it does not have
sufficient authority to change those records.
This is an operational and policy issue. It is out of scope for this
document to consider a technical solution or to propose an additional
protocol or mechanism to standardize the interaction between DNS
systems for authority negotiations.
o DNS Entries
DNS entries commonly have matching Reverse reverse DNS entries which that will also
need to be updated during renumbering. It might not be possible to
combine forward and reverse DNS entries update entry updates in one
procedure. procedure where
addresses are not being managed using DHCP.
o DNS data structure optimization Data Structure Optimization
[RFC2874] proposed an A6 record type for DNS recording of the IPv6
address and prefix. Several extensions to DNS query and processing
were also proposed. A6 was designed to be a replacement for the AAAA
record. The changes were designed to facilitate network renumbering
and multihoming. With the A6 record and the extensions, an IPv6
address could be defined by using multiple DNS records. This feature
would increase the complexity of resolvers but reduce the cost of
zone file maintenance, so renumbering could be easier than with the
AAAA record.
However, the
[RFC2874] has been deprecated and moved to Historic status by
[RFC6563]. The A6 record has not been widely used, used and has been shown
to have various problems and disadvantages (see section Section 2 in
[RFC6563]). It has been deprecated and moved to historic status by
[RFC6563]. The idea of a structured record to separate prefix and
suffix is still potentially valuable for renumbering, but avoiding
the problems of the A6 record would require a major development
effort.
10.3. Miscellaneous
o For the transport layer, [RFC5887] said that TCP connections and
UDP flows are rigidly bound to a given pair of IP addresses.
o For the application layer, in general, we can assert that any
implementation is at risk from renumbering if it does not check
whether an address is valid each time it starts session resumption
(e.g.
(e.g., a laptop wakes from sleep state). It is also more of or less
risky when it opens a new communications session by using cached
addresses.
We considered the above two points (ID/Locator overloading in
transport layer & and address caching in app application layer) are fundamental
issues that might not be proper to deal with them just in terms of
renumbering.
11. Security Considerations
o Prefix Validation
Prefixes from the ISP may need authentication to prevent prefix
fraud. Announcing changes of site prefix to other sites (for
example, those that configure routers or VPNs to point to the site in
question) also need needs validation.
In the LAN, Secure DHCPv6 ([I-D.ietf-dhc-secure-dhcpv6]) [SECURE-DHCPv6] or Secure Neighbor
Discovery (SEND, [RFC3971]) (SEND) [RFC3971] deployment may be needed to validate
prefixes.
o Influence on Security Controls
During renumbering, security controls (e.g. (e.g., ACLs) protecting
legitimate resources should not be interrupted. For example, if some
addresses are in a blacklist, they should not escape from the
blacklist due to renumbering.
If there are DHCPv6 authentication keys associated with an IP address
then the keys need to be changed for continually working when the
addresses are renumbered.
Addresses in SEND certificates are going to will need to get updated when
renumbering. During the overlap between old and new addresses, both
certificates must remain valid.
o Security Protection for Renumbering Notification
Section 7.1 mentions possible notification mechanisms to signal a
change in the DNS system or in the border routers related to a
renumbering event. Since the DNS system and border routers are key
elements in any network, and they might take action according to the
notification, a security authentication for the renumbering
notification is needed.
o Security Protection for Configuration Update
Automated configuration update approaches like [LEROY] would increase
the risk since a bad actor with the right permission could cause
havoc to the networks.
12. IANA Considerations
This draft does not request any IANA actions.
13. Acknowledgments
This work adopts significant amounts of content from [RFC5887] and
particularly [RFC5887]. In
addition, it draws largely from the "DNS Authority" topic in section Section
10.2 is from
[draft-chown-v6ops-renumber-thinkabout]. [IPv6-RENUM-THINK]. Both of the two documents
are offer such important
input for this work, work that some
principles/considerations principles and considerations applied
in this work are implicitly inherited from them. So thanks go to
Randall Atkinson, Hannu Flinck, Tim Chown, Mark Thompson, and Alan
Ford. Some useful materials were provided by Oliver Bonaventure and
his student student, Damien Leroy.
Many useful comments and contributions were made by Ted Lemon, Lee
Howard, Robert Sparks, S. Moonesamy, Fred Baker, Sean Turner, Benoit
Claise, Stephen Farrell, Brian Haberman, Joel Jaeggli, Eric Vyncke,
Phillips Matthew, Benedikt Stockebrand, Gustav Reinsberger, Teco Boot
Boot, and other members of the 6renum WG.
This document was prepared using 2-Word-v2.0.template.dot.
14. References
14.1. Normative References
[RFC3007] B. Wellington, B., "Secure Domain Name System (DNS) Dynamic
Update", RFC 3007, November 2000.
[RFC3315] R. Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins,
C., and M. Carney, "Dynamic Host Configuration Protocol
for IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic
Host Configuration Protocol (DHCP) version 6", RFC 3633,
December 2003.
[RFC3956] P. Savola, P. and B. Haberman. Haberman, "Embedding the Rendezvous
Point (RP) Address in an IPv6 Multicast Address.", Address", RFC
3956, November 2004.
[RFC3971] Arkko, J., Ed., Kempf, J., Zill, B., and P. Nikander Nikander,
"SEcure Neighbor Discovery (SEND)", RFC 3971, March 2005.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC
4861,September 4861,
September 2007.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862, September 2007.
14.2. Informative References
[RFC2072] H. Berkowitz, H., "Router Renumbering Guide", RFC2072, RFC 2072,
January 1997.
[RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering:
Defeating Denial of Service Attacks which employ IP
Source Address Spoofing", BCP 38, RFC 2267, January 1998. 2827, May 2000.
[RFC2865] Rigney, C., Willens, S., Rubens, A., and W. Simpson,
"Remote Authentication Dial In User Service (RADIUS)",
RFC 2865, June 2000.
[RFC2874] Crawford, M., M. and C. Huitema, "DNS Extensions to Support
IPv6 Address Aggregation and Renumbering", RFC 2874, July
2000.
[RFC2894] M. Crawford, M., "Router Renumbering for IPv6", RFC 2894,
August 2000.
[RFC3306] B. Haberman, B. and D. Thaler, "Unicast-Prefix-based IPv6
Multicast Addresses", RFC 3306, August 2002.
[RFC3956] P. Savola, P. and B. Haberman, "Embedding the Rendezvous
Point (RP) Address in an IPv6 Multicast Address", RFC 3965,
3956, November 2004.
[RFC4192] Baker, F., Lear, E., and R. Droms, "Procedures for
Renumbering an IPv6 Network without a Flag Day", RFC
4192, September 2005.
[RFC4704] Volz, B., "The Dynamic Host Configuration Protocol for
IPv6 (DHCPv6) Client Fully Qualified Domain Name (FQDN)
Option", RFC 4704, October 2006.
[RFC4714]
[RFC6241] Enns, R., "NETCONF Ed., Bjorklund, M., Ed., Schoenwaelder, J.,
Ed., and A. Bierman, Ed., "Network Configuration Protocol", Protocol
(NETCONF)", RFC 4714,
December 2006. 6241, June 2011.
[RFC4984] Meyer, D., Ed., Zhang, L., Ed., and K. Fall, Ed., "Report
from the IAB Workshop on Routing and Addressing", RFC
4984, September 2007.
[RFC5887] Carpenter, B., Atkinson, R., and H. Flinck, "Renumbering
Still Needs Work", RFC 5887, May 2010.
[RFC6275] Perkins, C., Ed., Johnson, D., and J. Arkko, "Mobility
Support in IPv6", RFC 6275, July 2011.
[RFC6563] Jiang, S., Conrad, D., and B. Carpenter, "Moving A6 to
Historic Status", RFC 6563, May March 2012.
[RFC6724] Thaler, D., Ed., Draves, R., Matsumoto, A., and T. Chown,
"Default Address Selection for Internet Protocol Version
6 (IPv6)", RFC 6724, September 2012.
[RFC6275] Johnson, D., Perkins, C., and J. Arkko, "Mobility Support
in IPv6", RFC 3775, June 2004.
[RFC6866] Carpenter, B. and S. Jiang, "Problem Statement for
Renumbering IPv6 Hosts with Static Addresses in
Enterprise Networks", RFC 6866, February 2013.
[RFC6879] Jiang, S., Liu, B., and B. Carpenter, "IPv6 Enterprise
Network Renumbering Scenarios, Considerations, and
Methods", RFC 6879, February 2013.
[I-D.ietf-6man-addr-select-opt]
[6MAN-ADDR-OPT]
Matsumoto, A.M., Fujisaki T.F., and T. Chown,
"Distributing Address Selection Policy using DHCPv6", Working
Work in Progress, April 2013.
[I-D.ietf-dhc-secure-dhcpv6]
Jiang, S., and Shen S., "Secure DHCPv6 Using CGAs", working
in progress, March 2012.
[I-D.ietf-dhc-addr-registration]
Jiang, S., Chen G., and S. Krishnan, "A Generic IPv6
Addresses Registration Solution Using DHCPv6", working in
progress, February 2013.
[I-D.liu-6renum-dhcpv6-slaac-switching]
[6RENUM-SLAAC]
Liu, B., "DHCPv6/SLAAC Address Configuration Switching
for Host Renumbering", Working Work in Progress, July 2012.
[I-D.liu-bonica-dhcpv6-slaac-problem]
[CFENGINE] CFEngine, <http://cfengine.com/what-is-cfengine>.
[DHCPv6-SLAAC]
Liu, B., B. and R. Bonica, "DHCPv6/SLAAC Address
Configuration Interaction Problem Statement", Working Work in
Progress, February 2013.
[cfengine]http://cfengine.com/what-is-cfengine
[IPv6-RENUM-THINK]
Chown, T., Thompson, M., Ford, A., and S. Venaas, "Things
to think about when Renumbering an IPv6 network", Work in
Progress, September 2006.
[LEROY] Leroy, D. and O. Bonaventure, "Preparing network
configurations for IPv6 renumbering", International of
Network Management, 2009, <http://
inl.info.ucl.ac.be/system/files/dleroy-nem-2009.pdf>
<http://inl.info.ucl.ac.be/system/files/leroy-
nem-2009.pdf>
[PREFIX-DHCPv6]
Jiang, S., Xia, F., and B. Sarikaya, "Prefix Assignment
in DHCPv6", Work in Progress, February 2013.
[SECURE-DHCPv6]
Jiang, S. and Shen S., "Secure DHCPv6 Using CGAs", Work
in Progress, March 2012.
Authors' Addresses
Bing Liu
Huawei Technologies Co., Ltd
Q14, Huawei Campus
No.156 Beiqing Rd.
Hai-Dian District, Beijing 100095
P.R. China
Email:
EMail: leo.liubing@huawei.com
Sheng Jiang
Huawei Technologies Co., Ltd
Q14, Huawei Campus
No.156 Beiqing Rd.
Hai-Dian District, Beijing 100095
P.R. China
Email:
EMail: jiangsheng@huawei.com
Brian Carpenter
Department of Computer Science
University of Auckland
PB 92019
Auckland, 1142
New Zealand
EMail: brian.e.carpenter@gmail.com
Stig Venaas
Cisco Systems
Tasman Drive
San Jose, CA 95134
USA
Email:
United States
EMail: stig@cisco.com
Wesley George
Time Warner Cable
13820 Sunrise Valley Drive
Herndon, VA 20171
USA
United States
Phone: +1 703-561-2540
Email:
EMail: wesley.george@twcable.com