wdiff rfc7059.original rfc7059.txt

Network Working Group
Independent Submission S. Steffann
Internet-Draft
Request for Comments: 7059 S.J.M. Steffann Consultancy
Intended status:
Category: Informational I. van Beijnum
Expires: December 2, 2013
ISSN: 2070-1721 Institute IMDEA Networks
R. van Rein
OpenFortress
May 31,
November 2013

A Comparison of IPv6 over IPv4 IPv6-over-IPv4 Tunnel Mechanisms
draft-steffann-tunnels-04

Abstract

This document provides an overview of various ways to tunnel IPv6
packets over IPv4 networks. It covers mechanisms in current use,
touches on several mechanisms that are now only of historic interest,
and discusses some newer tunnel mechanisms that are not (yet) widely used
at the time of publication. The goal of the document is helping
people with an IPv6-in-IPv4 tunneling need to select the mechanisms
that may apply to them.

Status of this This Memo

This Internet-Draft document is submitted in full conformance with not an Internet Standards Track specification; it is
published for informational purposes.

This is a contribution to the
provisions RFC Series, independently of BCP 78 any other
RFC stream. The RFC Editor has chosen to publish this document at
its discretion and BCP 79.

Internet-Drafts makes no statement about its value for
implementation or deployment. Documents approved for publication by
the RFC Editor are working documents not a candidate for any level of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list
Standard; see Section 2 of RFC 5741.

Information about the current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on December 2, 2013.
http://www.rfc-editor.org/info/rfc7059.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Tunnel Mechanisms . . . . . . . . . . . . . . . . . . . . . . 6
3.1. Configured Tunnels (Manual Tunnels / 6in4) . . . . . . . . 7
3.2. Automatic Tunneling . . . . . . . . . . . . . . . . . . . 8
3.3. IPv6 over IPv4 without Explicit Tunnels (6over4) . . . . . 8 9
3.4. Generic Routing Encapsulation (GRE) . . . . . . . . . . . 9 10
3.5. Connection of IPv6 Domains via IPv4 Clouds (6to4) . . . . 10
3.5.1. 6to4 Provider Managed Tunnels . . . . . . . . . . . . 11
3.6. Anything In Anything (AYIYA) . . . . . . . . . . . . . . . 12
3.7. Intra-site Intra-Site Automatic Tunnel Addressing (ISATAP) . . . . . 13
3.8. Tunneling IPv6 over UDP through NATs (Teredo) . . . . . . 14
3.9. IPv6 Rapid Deployment (6rd) . . . . . . . . . . . . . . . 14 15
3.10. Native IPv6 behind NAT44 CPEs (6a44) . . . . . . . . . . . 15 16
3.11. Locator/ID Separation Protocol (LISP) . . . . . . . . . . 16
3.12. Subnetwork Encapsulation and Adaptation Layer (SEAL) . . . 18
3.13. Peer-to-Peer IPv6 on Any Internetwork (6bed4) . . . . . . 18 19
4. Related Protocols . . . . . . . . . . . . . . . . . . . . . . 19 20
4.1. Tunnel Setup Protocol (TSP) . . . . . . . . . . . . . . . 20
4.2. SixXS Heartbeat Protocol . . . . . . . . . . . . . . . . . 20
4.3. Tunnel Information and Control protocol Protocol (TIC) . . . . . . 21
5. Common Aspects . . . . . . . . . . . . . . . . . . . . . . . . 21 22
5.1. Protocol 41 Encapsulation . . . . . . . . . . . . . . . . 21 22
5.2. NAT and Firewalls . . . . . . . . . . . . . . . . . . . . 22
5.3. MTU Considerations . . . . . . . . . . . . . . . . . . . . 24
5.4. IPv4 Addresses Embedded in IPv6 Addresses . . . . . . . . 25
6. Evaluation of Tunnel Mechanisms . . . . . . . . . . . . . . . 27 28
6.1. Efficiency of IPv4 Address Use . . . . . . . . . . . . . . 27 28
6.2. Supported Network Topologies . . . . . . . . . . . . . . . 28 29
6.3. Robustness . . . . . . . . . . . . . . . . . . . . . . . . 29 30
6.4. Gateway State . . . . . . . . . . . . . . . . . . . . . . 31 32
6.5. Performance . . . . . . . . . . . . . . . . . . . . . . . 32
7. IANA considerations . . . . . . . . . . . . . . . . . . . . . 33
8.
7. Security considerations Considerations . . . . . . . . . . . . . . . . . . . 33
9. 34
8. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 34
10. 35
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 34
11. 35
10. Informative References . . . . . . . . . . . . . . . . . . . . . . . . . . 34 35
Appendix A. Evaluation Criteria . . . . . . . . . . . . . . . . . 38
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 39 40

1. Introduction

During the transition from IPv4 to IPv6, IPv6 islands are separated
by a sea of IPv4. Tunnels provide connectivity between these IPv6
islands. Tunnels work by encapsulating IPv6 packets inside IPv4
packets, as shown in the figure.

Encapsulating IPv6 in IPv4

Various tunnel mechanisms have been proposed over time. So many many, in
fact, that it is difficult to get an overview. Some tunnel
mechanisms have been abandoned by the community, others have known problems
problems, and yet others have shown to be reliable. Some tunnel
mechanisms were designed with a particular use-case use case in mind, mind; others
are generic. There may be documented limitations as well as
limitations that have cropped up in deployment.

This document provides an overview of available and/or noteworthy
tunnel mechanisms, with the intention to guide selection of the best
mechanism for a particular purpose. As such, the discussion of the
different tunnel mechanisms is limited to the working principles of
the different mechanisms and a few important details.

Please use the references to learn the full details of each
mechanism. For brevity, only the most relevant documents are
referenced. Refer to these for additional specifications, updates updates,
and links to older versions of protocol specifications specifications, as well as
links to more general background information.

The intended audience for this document is everyone who needs a
connection to the IPv6 internet Internet at large, but is not in the position
to use native (untunneled) IPv6 connectivity, and thus needs to
select an appropriate tunnel mechanism. However, when native IPv6
connectivity is availalble, available, this should be preferred over tunneled
connectivity as per rule 7 in section Section 6 of [RFC6724]. This document
is also intended as a quick reference to tunnel mechanisms for the
IETF community.

The scope of this document is limited to tunnel mechanisms for
providing IPv6 connectivity over an IPv4 infrastructure. Mechanisms
for Virtual Private Networks (VPNs) and security architectures such
as IPSec IPsec [RFC4301], as well as IPv4 over IPv6 tunneling IPv4-over-IPv6 tunneling, are out of
scope for this document as they serve a different purpose, even if
they could technically be used to provide IPv6 connectivity.

2. Terminology

Anycast: Mechanism to provide a service, in multiple locations
and/or using multiple servers, by configuring each server with the
same IP address.

Carrier Grade

Carrier-Grade NAT (CGN): A Network Address Translation (see NAT)
device used by an ISP so multiple subscribers can be served using
a single IPv4 address.

Dual stack: Also known as "dual IP layer". Nodes run IPv4 and IPv6
side by side, and can communicate with other dual stack nodes
(using IPv4 or IPv6), as well as IPv4-only nodes (using IPv4) and
IPv6-only nodes (using IPv6). Most current operating systems are
set up to use IPv4 when available as well as use IPv6 when
available, allowing them to run in IPv4-only, IPv6-only IPv6-only, or dual
stack mode as circumstances permit. Except for a few things
concerning the Domain Name System (DNS), there is no separate
specification for dual stack beyond the specifications relevant to
running IPv4 and IPv6. Dual stack is one of the three IPv4-to-
IPv6 transition tools; the others are translation and tunnels.

Encapsulation: Transporting packets a packet as data inside another packet.
For instance, an IPv6 packet inside an IPv4 packet.

Firewall: A device that selectively filters IP packets, allowing
some protocols through but not others. A firewall may act as a
switch, operating below the IP layer, or as a router.

Host: A device that communicates using the Internet Protocol and
only transmits packets from its own address.

ISP: Internet Service Provider; the party connecting the outside of
the local network's perimeter to the public Internet.

MTU: Maximum Transmission unit, Unit, the maximum size of a packet that
can be transmitted over a link (or tunnel) without splitting it
into multiple fragments.

NAT: Network Address Translation or Network Address Translator. NAT
makes it possible for a number of hosts to share a single IP
address. TCP and UDP port numbers are used to distinguish the
traffic to/from different hosts served by the NAT; protocols other
than TCP and UDP may be incompatible with NAT due to lack of port
numbers. NAT also breaks protocols that depend on the IP
addresses used in some way. Typically, NAT devices behave as a
host towards the public internet, Internet, and as a router towards the
internal network.

NBMA: Non-Broadcast, Multiple Access. Non-Broadcast Multi-Access. This is a network configuration
in which nodes can exchange packets directly by addressing them at
the desired destination. However, broadcasts or multicasts are
not supported, so autodiscovery mechanisms such as IPv6 Neighbour
Discovery must be modified to use unicast to work.

Node: A device that implements IP, either a host or a router; also
known as a system. See note at "NAT".

Path stretch: The difference between the shortest path through the
network and the path (tunneled) packets actually take.

PMTUD: Path MTU Discovery, a method to determine the smallest MTU on
the path between two nodes. There are separate specifications for
PMTUD over IPv4 [RFC1191] and IPv6 [RFC1981].

Router: A device that forwards IP packets that it didn't generate
itself. See note at "NAT".

System: A device that implements IP, either a host or a router; a
network node.

Translation: The IPv6 and IPv4 headers are similar enough that it is
possible to translate between them. This allows IPv6-only hosts
to communicate with IPv4-only hosts. The original specification
for translating between IPv6 and IPv4, IPv4 was heavily criticised by
the Internet Architecture Board, but new specifications for
translating between IPv6 and IPv4 were later published [RFC6145].
Translation is one of the three IPv4-to-IPv6 transition tools; the
others are dual stack and tunnels.

Tunnel: By encapsulating IPv6 packets inside IPv4 packets, IPv6-
capable hosts and IPv6-capable networks isolated from other IPv6-
capable systems or the IPv6 internet Internet at large can exchange IPv6
packets over IPv4-only infrastructure. There are numerous ways to
tunnel IPv6 over IPv4. This document compares these mechanisms.
One
Tunneling is one of the three IPv4-to-IPv6 transition tools; the
others are translation and dual stack.

Tunnel broker: A service that provides tunneled connectivity to the
IPv6 internet, Internet, such as SixXS [SIXXS], [TUNBROKER] tunnelbroker.net
[TUNBROKER], and gogo6 [GOGO6].

3. Tunnel Mechanisms

Automatic tunnels (Section 3.2), configured tunnels (Section 3.1),
6over4 (Section 3.3), 6to4 (Section 3.5), ISATAP the Intra-Site Automatic
Tunnel Addressing Protocol (ISATAP) (Section 3.7) 3.7), and 6rd
(Section 3.9) solve similar problems at different scales. They all
encapsulate IPv6 packets immediately inside an IPv4 packet, without
using additional headers. This is called "protocol 41 encapsulation"
(see Section 5.1), as the Protocol field in the IPv4 header is set to
41 to indicate that what follows is an IPv6 packet.

Each of these mechanisms also creates

6to4, 6rd, ISATAP, and automatic tunneling each generate an IPv6
address or range of IPv6 addresses for the host or router running the
protocol based on the system's IPv4 address in one way or another
(see Section 5.4). This lets 6to4, 6rd, ISATAP ISATAP, and automatic
tunnels determine the IPv4 destination address in the outer IPv4
header from the IPv6 address of the destination, allowing for
automatic operation without the need to administratively configure
the remote tunnel endpoint.

6over4 and ISATAP provide IPv6 connectivity between IPv6-capable
systems within a single organisation's network that is otherwise
IPv4-only. IPv4
only. 6rd allows ISPs to provide IPv6 connectivity to their
customers over IPv4-only last mile last-mile infrastructures. 6to4 directly
provides connectivity to the global IPv6 internet Internet without involving
an ISP.

Configured tunnels (Section 3.1) also use protocol 41 encapsulation, encapsulation
but rely on manual configuration of the remote tunnel endpoint. (The
Heartbeat Protocol (Section 4.2) solves this.) Configured tunnels
can be used within an organisation's network, network but are typically used
by tunnel broker tunnel-broker services to provide connectivity to the IPv6
internet.
Internet. GRE (Section 3.4) is similar to configured tunnels, but
also supports tunnel encapsulating protocols other than IPv6.

AYIYA (Section 3.6) is similar to configured tunnels and GRE, GRE but
typically uses a UDP header for better compatibility with NATs and is
generally used with TIC the Tunnel Information and Control (TIC) protocol
(Section 4.3) to set up the tunnel rather than rely on manual
configuration. Teredo (Section 3.8), 6a44 (Section 3.10) 3.10), and 6bed4
(Section 3.13) are similar to 6to4, except that they are designed to
work through NATs by running over UDP. Of these, Teredo and 6bed4
assume no ISP involvement and 6a44 does; and 6bed4 is designed to work
over direct IPv4 paths between peers whenever possible.

LISP

The Locator/ID Separation Protocol (LISP) (Section 3.11) is a system
for abstracting the identifying function from the location function
of IP addresses, which addresses; this allows for the use of IPv6 for the former and
IPv4 for the latter.

SEAL

The Subnetwork Encapsulation and Adaptation Layer (SEAL)
(Section 3.12)) 3.12) and its companion technologies (VET, AERO, IRON (Virtual Enterprise
Traversal (VET), Asymmetric Extended Route Optimization (AERO),
Internet Routing Overlay Network (IRON), and Routing and RANGER) Addressing
in Networks with Global Enterprise Recursion (RANGER)) provide a
configured tunnel system for IPv6-in-IPv4 tunneling to default
routers as well as automatic tunnel endpoint discovery for
optimisation of more-specific routes.

Dual-Stack Lite [RFC6333] and MAP [I-D.ietf-softwire-map], [MAP], both developed by the IETF
Softwire working group, often come up in discussions about IPv6
tunneling. However, they are _not_ IPv6-in-
IPv4 IPv6-in-IPv4 tunnel mechanisms.
They are IPv4-in-IPv6 mechanisms for providing IPv4 connectivity over
an IPv6 infrastructure.

Please refer to Section 5 for more information about issues common to
many tunnel mechanisms; those issues are not discussed separately for
each mechanism. The mechanisms are discussed below in roughly
chronological order of first publication. order.

3.1. Configured Tunnels (Manual Tunnels / 6in4)

Configured and automatic tunnels are the two oldest tunnel
mechanisms, originally published in "Transition Mechanisms for IPv6
Hosts and Routers" [RFC1933] in 1996. The latest specification of
configured tunnels is "Basic Transition Mechanisms for IPv6 Hosts and
Routers" [RFC4213], published in 2005. The mechanism is sometimes
called "manual tunnels", "static tunnels", "protocol 41 tunnels" tunnels", or
"6in4".

Configured tunnels connect two systems in point-to-point fashion
using protocol 41 encapsulation. The configuration that the name of
the mechanism alludes to consists of a remote "tunnel endpoint".

This is the IPv4 address of the system on the other side of the
tunnel. When a system (potentially) has multiple IPv4 addresses, the
local tunnel endpoint address may also need to be configured.

The need to explicitly set up a configured tunnel tunnels makes them more
difficult to deploy than automatic mechanisms. However, because
there is a fixed, single remote tunnel endpoint, performance is
predictable and the tunnel is easy to debug.

In the early days days, it was not unheard of for a small network to get
IPv6 connectivity from another continent. This excessive path
stretch makes communication over short geographic distances much less
efficient because the distance travelled by packets may be larger
than the geographic distance by an order of magnitude or more.

Configured tunnels are widely implemented. Common operating systems
can terminate configured tunnels, as well as IPv6-capable routers and
home gateways. The mechanism is versatile, versatile but is mostly used between
isolated smaller IPv6-capable networks and the IPv6 internet, Internet, often
through a "tunnel broker" such as tunnelbroker.net [TUNBROKER], SixXS [SIXXS]
[SIXXS], or gogo6 [GOGO6].

[RFC4891] discusses the use of IPsec to protect the confidentiality
and integrity of IPv6 traffic exchanged over configured tunnels.

3.2. Automatic Tunneling

Automatic tunneling is described in [RFC2893], "Transition Mechanisms
for IPv6 Hosts and Routers", but removed in [RFC4213], which is an
update a
replacement of RFC 2893. Configured tunnels (Section 3.1) are
closely related to automatic tunnels and are specified in RFCs 2893
and 4213, too. Both use protocol 41 encapsulation.

Hosts that are capable of automatic tunneling use special IPv6
addresses: IPv4-compatible addresses. An IPv4-compatible IPv6
address consists of 96 zero bits followed by the system's IPv4
address. When sending packets to destinations within the IPv4-
compatible ::/96 prefix, the IPv4 destination address in the outer
IPv4 header is taken from the IPv4 address in the IPv4-compatible
IPv6 destination address.

Automatic tunneling has a big limitation: it only allows for
communication between IPv6-capable systems that both support
automatic tunneling. There are no provisions for communicating with
the native IPv6 internet. Internet. As such, the mechanism is of almost no
practical use and is not implemented in current operating systems, as
6to4 (Section 3.5) does what automatic tunneling was supposed to do,
but it also provides connectivity to the rest of the IPv6 internet. Internet.

3.3. IPv6 over IPv4 without Explicit Tunnels (6over4)

"Transmission of IPv6 over IPv4 Domains without Explicit Tunnels"
[RFC2529] was published in 1999. The mechanism is commonly known as
"6over4".

6over4 is designed to work within a single organisation's IPv4
network, where IPv6-capable hosts and routers are separated by IPv4-
only routers. 6over4 treats the IPv4 network as a "virtual Ethernet"
for the purpose of IPv6 communication. It uses IPv4 multicast to
tunnel IPv6 multicast packets. A node's IPv4 address is included in
the Interface Identifier used on the virtual 6over4 interface,
allowing the exchange of protocol 41 encapsulated packets between
6over4 nodes without prior administrative configuration.

Because multicast is supported, standard IPv6 Neighbour Discovery and
Stateless Address Autoconfiguration [RFC4862] can be used. Although Although,
like automatic tunnels (Section 3.2) and other mechanisms, 6over4
embeds the IPv4 address of the host is in the IPv6 address, the
destination IPv4 address in the outer IPv4 header is *not* derived
from the IPv6 address embedded in the inner IPv6 header, but learnt
through Neighbour Discovery [RFC4861]. In effect, the IPv4 addresses
of the hosts are used as link-layer addresses, addresses in the same way that
MAC
Media Access Control (MAC) addresses are used on Ethernet networks.

One or more routers with connectivity to the global IPv6 internet Internet
send out Router Advertisements to provide 6over4 hosts with
connectivity to the rest of the IPv6 internet. Internet.

6over4 has the minimal overhead for protocol 41 encapsulation overhead and
doesn't require manual configuration. Hosts can only take advantage
of 6over4 if they run the mechanism themselves. 6over4 packets can't
pass through a NAT successfully, as the IPv4 address exchanged
through Neighbour Discovery will be different from the one needed to
reach the host in question, and because because, without port numbers,
protocol 41 doesn't allow for multiplexing multiple hosts using this
encapsulation behind a single IPv4 address. However, 6over4 works
within IPv4 domains that reside behind a NAT in their entirety and
use [RFC1918] RFC 1918 addressing.

Because of its reliance on IPv4 multicast and because local IPv6
communication is relatively easy to facilitate using IPv6 routers,
6over4 is not supported in current operating systems. ISATAP
(Section 3.7) provides very similar functionality without requiring
IPv4 multicast capability, capability and is implemented more widely.

3.4. Generic Routing Encapsulation (GRE)

Generic Routing Encapsulation (GRE) [RFC2784] is a generic point-to-
point tunnel mechanism that allows many other protocols to be
encapsulated in IP.

GRE is a simple protocol which that is similar to configured tunnels
(Section 3.1) when used for IPv6-in-IPv4 tunneling. The main benefit
of GRE is that it can encapsulate any protocol's packets, not only encapsulate
IPv6 packets but any
protocol. packets. The GRE header causes an extra overhead of 8 to 16
bytes depending on which options are used. GRE sets the Protocol
field in the IP header to 47.

The GRE header can optionally contain a checksum, a key to separate
different traffic flows (for example, different tunnels) between the
same end points endpoints, and a sequence number that can be used to prevent
packets from being processed out of order.

GRE is implemented in many routers, routers but not in most consumer-level
home gateways or desktop operating systems.

3.5. Connection of IPv6 Domains via IPv4 Clouds (6to4)

6to4 is specified in "Connection of IPv6 Domains via IPv4 Clouds"
[RFC3056]. It creates a block of IPv6 addresses from a locally
configured IPv4 address by concatenating that IPv4 address to the
prefix 2002::/16, resulting in a /48 IPv6 prefix. Addresses in
2002::/16 are considered reachable through the tunnel interface, so
the 6to4 network functions as a non-broadcast, multiple access Non-Broadcast Multi-Access (NBMA)
network through which 6to4 users can communicate. IPv6 packets are
encapsulated by adding an IPv4 header with the Protocol field set to
41.

The /48 prefix allows a single system running 6to4 to act as a
gateway or router for a large number of IPv6 hosts. Alternatively,
an individual host may run 6to4 and not act as a gateway or router.
The system running 6to4 must have a globally reachable IPv4 address.
Using 6to4 with a private IPv4 address [RFC1918] is not possible.

"An Anycast Prefix for 6to4 Relay Routers" [RFC3068] specifies an
anycast mechanism for 6to4 relays that provide connectivity between
the 6to4 network and the regular IPv6 internet. Internet. All public relays
share the IPv4 address 192.88.99.1, which corresponds to 2002:c058:
6301::. Relays advertise reachability towards 2002::/16 towards to the
native IPv6 internet, Internet, so packets addressed to systems using 6to4
addresses are routed to the closest gateway. The gateway
encapsulates these packets and forwards them to the IPv4 address
included in the IPv6 address. Systems running 6to4 have a default
route pointing to 2002:c058:6301::, so they tunnel packets addressed
to non-6to4 IPv6 destinations to the closest relay, which
decapsulates the packet and forwards them as IPv6 packets.

The 6to4 protocol adds minimal overhead for protocol 41 overhead encapsulation
and requires no manual configuration from users. The biggest problem
specific to 6to4 is that it is unpredictable which 6to4 anycast relay
is used. These relays are often provided by third parties on a best-effort best-
effort basis. In practice practice, this has caused unpredictable
performance. Traffic from the 6to4 network to the regular IPv6 internet
Internet will likely use a different 6to4 relay than the traffic in
the opposite direction. If either of those relays is not reliable reliable,
then the communication between those networks is affected.
Especially the lack of control over the relay used for return traffic
is considered to be a problem with 6to4.

To avoid problems with 6to4 6to4, the IPv6 Default Address Selection
algorithm [RFC6724] gives IPv4 addresses a higher preference than
6to4 addresses. When making a connection connection, a system will prefer
native IPv6 over IPv4, and IPv4 over 6to4 IPv6. This causes 6to4 to
be used only when a destination is not reachable over IPv4 and no
other IPv6 connectivity is available.

For more information about 6to4, see "Advisory Guidelines for 6to4
Deployment" [RFC6343].

*Warning*:

Although many, if not all, 6to4 implementations disable the mechanism
when the system only has an RFC 1918 address, recently a block of
IPv4 address addresses has been set aside for use in service provider service-provider-
operated Network Address Translators, also known as Carrier Grade NAT (CGN). Carrier-Grade
NATs (CGNs). [RFC6598] sets aside the block 100.64.0.0/10 for the
use between CGNs and subscriber devices. As 100.64.0.0/10 is not an
RFC 1918 address block, systems implementing 6to4 may fail to disable
the mechanism, but due to the shared nature of the 100.64.0.0/10
prefix, 6to4 cannot work using these addresses. The same issue is
present if an ISP decides to use regular global unicast IPv4 address
space behind a CGN.

3.5.1. 6to4 Provider Managed Tunnels

[RFC6732] describes "6to4 Provider Managed Tunnels", provider managed tunnels", which is are a way
to make 6to4 work behind a CGN. This is accomplished by running a
6to4 gateway at the 6to4 gateway anycast address, and then
translating the IPv6 addresses used by 6to4 users behind the CGN to
IPv6 addresses from the ISP's range. Unlike IPv4 NAT, where multiple
internal hosts share a single public IPv4 address, prefix translation
translates
maps entire prefixes, so each host has its own public IPv6 address
and can receive incoming packets as usual.

However, if IPv6 applications are not aware that translation is
happening (and they have no reason to expect that it is), they may
not use their externally visible address in referrals, so
applications that use referrals are likely to fail. Additionally,
the translation is only specified for packets that flow through the
6to4 gateway, not for packets sent directly to other 6to4 users. So So,
communication with other 6to4 users is not possible. As such, the
use of 6to4 provider managed tunnels is discouraged except as a very
last resort.

3.6. Anything In Anything (AYIYA)

AYIYA [AYIYA] is designed for use by the SIXXS SixXS [SIXXS] tunnel broker tunnel-broker
service. The For more information, see the specification has been published as an Internet-Draft
[I-D.massar-v6ops-ayiya]. [MASSAR].

The AYIYA protocol defines a method for encapsulating any protocol in
any other protocol. The most common way of deploying AYIYA is to use
the following sequence of headers: IPv4-UDP-AYIYA-IPv6, although
other combinations like IPv4-AYIYA-IPv6 or IPv6-SCTP-AYIYA-IPv4 are
also possible. The draft That document does not limit the contents nor the
protocol that carries the AYIYA packets. In this document document, we only
look at the most common usage (IPv4-UDP-AYIYA-IPv6) which that is deployed
on the SixXS tunnel brokers to provide IPv6 access to clients behind
NAT devices.

AYIYA specifies the encapsulation, identification, checksum, security
security, and certain management operations that can be used once the
tunnel is established. It does not specify how the tunnel
configuration parameters can be negotiated. Typically, the TIC
protocol described in Section 4.3 protocol is used for that part of the tunnel
setup, although the TSP protocol Tunnel Setup Protocol (TSP) (Section 4.1) could
just as well be used.

AYIYA provides a point-to-point tunnel, over which the endpoints can
route traffic for any source and destination. When using SHA-1
hashing for authentication, as is common when using the AICCU Automatic
IPv6 Connectivity Client Utility (AICCU) client with a SixXS tunnel
server, the total packet overhead is 72 bytes (20 for the IPv4
header, 8 for UDP UDP, and 44 for AYIYA).

AYIYA provides operational commands for querying the hostname,
address, contact information, software version version, and last error
message. An operational command to ask the other side of the tunnel
to shut down is also available. These commands in the protocol can
make debugging of AYIYA tunnels easier if the tools support them.

The main advantage of AYIYA is that it can provide a stable tunnel
through an IPv4 NAT, and possibly multiple layers of NAT. The UDP port numbers allow multiple AYIYA users
to share a single IPv4 address behind a NAT.

The client will contact the tunnel server at regular intervals intervals, and
the tunnel server will automatically adapt to changing IPv4 addresses
and/or UDP port numbers. To prevent a third party from injecting
rogue packets into the tunnel tunnel, the client can optionally be
authenticated by using the identity and signature fields. A
timestamp is included in the AYIYA header to guard against replay
attacks.

There is currently a single implementation of this protocol: the
AICCU [AICCU] client software used with the SIXXS SixXS [SIXXS] tunnel tunnel-
broker service.

3.7. Intra-site Intra-Site Automatic Tunnel Addressing (ISATAP)

ISATAP [RFC5214] uses protocol 41 encapsulation, encapsulation to provide
connectivity between isolated IPv6-capable nodes within an
organisation's internal network. It is similar to 6over4
(Section 3.3), but without the requirement that the IPv4 network
supports multicast; unlike 6over4, ISATAP uses a Non-Broadcast
Multiple Multi-
Access (NBMA) communication model and thus doesn't support
multicasts. The mechanism assigns IPv6 addresses whose interface
identifier Interface
Identifier is solely defined by a node's IPv4 address, which is
assumed to be unique.

In order to obtain a /64 prefix, an ISATAP host needs to send a
unicast Router Solicitation to receive a unicast Router Advertisement
from an ISATAP router. Without the ability to send and receive IPv6
multicasts, an ISATAP host must be configured with a Potential Router
List through an all-IPv4 mechanism, such as manual setup, DHCP DHCP, or
the DNS. Site administrators are encouraged to use a DNS Fully
Qualified Domain Name using the convention "isatap.domainname" (e.g.,
isatap.example.com). Hosts will accept packets with IPv4 sender
addresses that are either on the Potential Router List, List or that are embedded in
the IPv6 sender address.

The router's prefix and the IPv4 address together define the IPv6
address for the ISATAP interface. This means that precisely one
ISATAP address is available for each IPv4 address. As such, each
host needs to run ISATAP itself in order to enjoy ISATAP IPv6
connectivity. The IPv4 address in the destination IPv6 address is
used to bootstrap Neighbour Discovery.

[RFC5214] doesn't explicitly address the use of ISATAP using private
[RFC1918]
RFC 1918 addresses. Despite that, the mechanism seems compatible
with private addresses. NAT, however, breaks the relationship
between the IPv4 address embedded in the IPv6 address and would
therefore make communication between ISATAP hosts impossible. Any
device that can communicate with the ISATAP hosts over IPv4 using
protocol 41 can participate in the IPv6 subnet.

ISATAP is available in Windows, Linux Linux, and Cisco IOS.

3.8. Tunneling IPv6 over UDP through NATs (Teredo)

Teredo is specified in [RFC4380] and a few updates; it is designed as
an automatic tunnel mechanism of last resort. It can configure an
IPv6 address behind most NAT devices, but not all. Because Teredo
uses encapsulation in UDP, multiple Teredo clients can be
simultaneously active behind the same NAT. For each Teredo client, a
single IPv6 address is then created at the expense of a single
external UDP port.

The operation of Teredo is based on a classification of NAT [RFC3489]
as established during an interaction with a Teredo server. This
classification has since been obsoleted [RFC5389] (by [RFC5389]) because it
assigns more properties to NAT than achieved in reality.

Teredo is present in Windows XP and later, later and is enabled by default
in Windows Vista and later. However, Windows will only use Teredo
connectivity as a way to connect to IPv6 destinations of last resort.
If no other if IPv6 connectivity is present, only
possible through Teredo, then Windows will not even look up AAAA records
when resolving domain names. This means that Teredo is only used to
connect to explicit IPv6 addresses obtained through another mechanism
than DNS. An open source open-source implementation named Miredo exists for
other platforms.

The performance of Teredo falls noticeably short of that of IPv4.
The setup time of a connection involves finding a Teredo relay nearby
the native address to encapsulate and decapsulate traffic, and
finding this relay can take in the order of seconds. This process is
not sufficiently reliable; Teredo fails in about 37% [TERTST] of its
attempts to connect to native IPv6 destinations. The round trip roundtrip time
of traffic can add tenths of a second, and jitter generally worsens
if it is dependent on a public relay.

Teredo clients need to be configured with a Teredo server when
setting up their local IPv6 address and when initiating a connection
to a native IPv6 destination. The hostnames of the Teredo servers
are usually pre-configured preconfigured by the vendor of the Teredo implementation.
All Microsoft Windows implementation implementations use Teredo servers provided by
Microsoft by default.

3.9. IPv6 Rapid Deployment (6rd)

6rd [RFC5969] is used by service providers to connect customer
networks behind a CPE (Customer Premises Equipment) to the IPv6 internet.
Internet.

The structure of the 6rd protocol is based on 6to4 6to4, and it has the
same minimal overhead as all protocols that use protocol 41
encapsulation. The main differences between 6rd and 6to4 are that
6rd is meant to be used inside a service provider's network and does
not use a special IPv6 prefix but one or more prefixes routed to the
service provider. As such, 6rd users aren't immediately recognisable
by their IPv6 address the way 6to4 users are. Where 6to4 uses relays
based on global anycast routing routing, 6rd uses relays provided and
maintained by the service provider. Because of this architecture architecture,
the tunnel does not traverse unknown networks which networks; this makes any
debugging much easier.

6rd is completely stateless once it is configured. The tunnel
endpoints can therefore be deployed using anycast. This is commonly
done for the 6rd border relays deployed by the service provider to
provide redundancy.

Because of the different prefix, the device used as the 6rd client
cannot use the hard-coded IPv6 prefix calculation and relay addresses
of 6to4. Instead, the 6rd client needs to receive configuration
information to work. In principle principle, 6rd nodes may be configured in a
variety of ways, the most common one being through DHCP. If the
client receives its IPv4 address from a DHCPv4 server server, then the 6rd
configuration can be included in the DHCP message exchange using the
6rd DHCPv4 Option defined in [RFC5969]. Manual configuration of 6rd
options and configuration using [TR-069] is also possible.

The main advantage of using 6rd is that it allows service providers
to deploy IPv6 on last mile last-mile access networks that for some reason
cannot provide native IPv6 connectivity. It does not share the lack
of predictable routing that 6to4 suffers from, from because all routing,
encapsulation
encapsulation, and de-encapsulation is decapsulation are done by the service provider.

6rd is intended to be a service managed by an ISP or enterprise IT
department, which
department that must explicitly make 6rd available for clients to be
able to use it.

3.10. Native IPv6 behind NAT44 CPEs (6a44)

Inspired by Teredo, the 6a44 tunnel is described in "Native IPv6
behind IPv4-to-IPv4 NAT Customer Premise Premises Equipment (6a44)"
[RFC6751]. Its purpose is to enable Internet Service Providers to
establish IPv6 connectivity for their customers, in spite of the use
of a CPE or home gateway that is not prepared for IPv6. The
infrastructure required for this is a 6a44 relay in the ISP's network
and a 6a44 client in the customer's internal network.

6a44 was explicitly designed to overcome the noted problems with
Teredo. Where Teredo was designed as a global solution without
dependency on ISP co-operation, cooperation, the 6a44 tunnel explicitly assumes ISP co-operation.
cooperation. Instead of using Teredo's well-known prefix, a /48
prefix out of the ISP's address space is used. A well-known
(anycast) IPv4 address has been assigned for the 6a44 relay to be run
inside the ISP network without client configuration. This well-known
address is allocated from the same IPv4 /24 as 6to4.

As part of its bootstrapping, a 6a44 client requests an address from
the 6a44 relay, and a regular keepalive sent by the 6a44 client to
the 6a44 relay keeps mapping state in NATs and firewalls on the path
alive. Traffic passed from the native IPv6 internet Internet to 6a44 is
encapsulated in UDP and IPv4 by the relay and decapsulated by the
6a44 client; the opposite is done in the other direction.

3.11. Locator/ID Separation Protocol (LISP)

The Locator/ID Separation Protocol (LISP) [RFC6830] is a protocol to
separate the identity of systems from their location on the internet Internet
and/or internal network. The addresses of the systems are called
Endpoint Identifiers (EIDs) (EIDs), and the addresses of the gateways are
called Routing Locators (RLOCs). It is possible to use IPv6 EIDs
with IPv4 RLOCs and thereby use LISP for tunneling IPv6 over IPv4.

LISP defines its own packet formats for encapsulation of data packets
and for control messages. All such packets are then encapsulated in
UDP. Data packets use port 4341 4341, and control packets use port 4342.

The LISP specification consists of several RFC documents. RFCs. The relevant ones
for IPv6-in-IPv4 tunneling are the base specification [RFC6830], Interworking
"Interworking between Locator/ID Separation Protocol (LISP) and Non-LISP Sites [RFC6832] Non-
LISP Sites" [RFC6832], and the Locator/ID "Locator/ID Separation Protocol (LISP)
Map-Server Interface Interface" [RFC6833].

+----+ +----+
| MS | | MR |
+----+ +----+ +-----+ /-----------\
| | /---| xTR |---| LISP site |
+------+ /------------\---/ +-----+ \-----------/
| PxTR |---| IP network |
+------+ \------------/---\ +-----+ /-----------\
| \---| xTR |---| LISP site |
/---------------\ +-----+ \-----------/
| Non-LISP site |
\---------------/

An example Example of a LISP deployment Deployment

LISP introduces new terminology and new concepts. The relevant ones
for this document are:

ITR: Ingress Tunnel Router, a router encapsulating data packets at
the border of a LISP site

ETR: Egress Tunnel Router, a router decapsulating data packets at
the border of a LISP site

xTR: A router performing both the ITR and the ETR functions

PITR: Proxy ITR, a router accepting traffic from non-LISP sites,
encapsulating it it, and tunneling it to the LISP sites

PETR: Proxy ETR, a router accepting traffic from LISP sites to send
it to non-LISP sites

PxTR: A router performing both the PITR and the PETR functions

MS: Map Server, a server accepting RLOC registrations from ETRs

MR: Map Resolver, a server that can resolve queries for RLOCs from
ITRs

LISP ETRs register the EID prefixes that for which they can handle traffic for
in
with one or more Map Servers. ITRs and PITRs can then query Map
Resolvers to determine which RLOCs to use when sending traffic to a
LISP site. PITRs advertise aggregates of EID prefixes to the global
routing table and provide tunneling services for them so that non-
LISP sites can reach LISP sites. PETRs provide a way for LISP sites
to send traffic to non-LISP sites.

LISP is a complex protocol if only used for tunneling. What it
provides additionally is Features of
LISP are that ETRs can advertise their own RLOC addresses, that one
site can have multiple xTRs with independent
RLOCs RLOCs, and that the LISP
site administrator can specify priorities and weights for those
RLOCs. This provides redundancy and explicit load balancing between
RLOCs. It also provides allows for automatic tunneling between different
sites without using a PxTR if both sites use Map Servers and Map
Resolvers that are interconnected, for example example, by participating in
the LISP Beta Network [LISPBETA]. To facilitate these interconnections
interconnections, the LISP Delegated Database Tree (DDT) system is
available.

The

LISP protocol is implemented on most Cisco devices. There are implementations
available for FreeBSD and Linux, as well as a
platform independent platform-independent
implementation in the Python programming language. Note that for
LISP to work, a mapping service not unlike the DNS must be in place.

3.12. Subnetwork Encapsulation and Adaptation Layer (SEAL)

The Subnetwork Encapsulation and Adaptation Layer (SEAL)
[I-D.templin-intarea-seal] [SEAL]
(along with its companion technologies cited therein) provides a
hybrid configured/automatic tunneling system. SEAL itself provides a
mid-layer of encapsulation between the inner IPv6 header and the
outer IPv4 header, i.e., as IPv4-SEAL-
IPv6. IPv4-SEAL-IPv6. SEAL can also be used in
conjunction with an outer UDP encapsulation header, e.g., if NAT
traversal is necessary.

The SEAL tunnel endpoint creates bidirectional configured tunnels to
reach default IPv6 routers, and it discovers unidirectional automatic
tunnels. SEAL tunnels can be configured over multiple underlying
IPv4 links whether the addresses are provisioned from public or
private IPv4 addressing domains. In that case, multi-homing multihoming and
traffic engineering are naturally supported.

SEAL provides an optional 32-bit Identifier identifier and variable-length
Integrity Check Vector that can be used for packet identification,
message origin authentication, anti-replay anti-replay, and a mid-layer
segmentation and reassembly capability. SEAL also provides a SEAL
Control Message Protocol (SCMP) used for neighbour coordinations
between tunnel endpoints. These coordinations are used for functions
such as tunnel MTU signalling, route optimisations, neighbour
reachability testing testing, and so on.

SEAL ensures that packets that are no larger than 1500 bytes can be
transported through the tunnel by using a tunnel segmentation
function. IPv6 packets that are too large to transport through the
tunnel whole are split into segments. The segments are encapsulated
in IPv4 and reassembled into the original IPv6 packets at the remote
tunnel endpoint. SEAL also admits packets larger than 1500 bytes
into the tunnel on a best-effort basis in case the path between the
tunnel endpoints can support the larger size.

When SEAL is used alone without its companion technologies, it can be
used in the same scenarios as for GRE. However, SEAL provides
advanced capabilities that make it better suited than GRE for many
use cases. There is currently an experimental open source open-source
implementation of SEAL.

3.13. Peer-to-Peer IPv6 on Any Internetwork (6bed4)

The 6bed4 tunnel is specified in "6bed4: Peer-to-Peer IPv6 on Any
Internetwork" [6BED4]. A specific goal of 6bed4 is to achieve direct
communication between peers when the intermediate infrastructure does
not prohibit it. The advantage of direct communication is to get a
performance level similar to IPv4. The address of a 6bed4 peer is
formed from the external publicly visible IPv4 address and UDP port. The
tunnel service used for fallback connectivity can run anywhere; anywhere --
perhaps at the local ISP or perhaps with a third party third-party service provider for
6bed4, or even on a well-known address. It is currently an NBMA
protocol; there are openings for expansion with multicast.

The setup of 6bed4 is somewhat similar to 6to4, except that it
employs UDP so it can be used behind NAT. It also has elements found
in Teredo, Teredo but without a need to classify NATs and induce behaviour
from that. The 6bed4 tunnel makes no assumption assumptions about the
capabilities of NAT devices beyond being able to do straightforward
NAT on UDP support. packets. Given this, 6bed4 can create reliable IPv6
tunnels.

In environments where direct connections between 6bed4 peers is are
possible, additional path stretch compared to IPv4 communication is
avoided, so 6bed4 performance comes close to IPv4 performance. In
situations where this it is not possible to run over the direct path
between two peers because a NAT that does not conform to [RFC4787] is
on the path, a fallback to a tunnel server is used. This increases
path stretch and affects scalability through its impact on roundtrip
times and jitter.

Another area where the tunnel server is needed, needed is for connectivity
between 6bed4 peers and native IPv6 hosts. For reasons of
performance and scalability, connections between 6bed4 peers are
preferred over connections between a 6bed4 peer and a native IPv6
host. A default address exists to support zero-config operation, but
it is possible to locally configure a tunnel server as a fallback
route, which then also defines the tunnel server for the return path.

6bed4 has been specifically designed to support realtime real-time interactive
traffic streams, such as SIP calls, between 6bed4-supporting end
points, assuming that each prefers 6bed4-to-6bed4 traffic over 6bed4-
to-native traffic. Under that premise, the only hosts that need to
go through a tunnel server are those that are behind a NAT with
Address-Dependent Mapping or Address and Port-Dependent Mapping. A
number of different implementations of 6bed4 have been constructed
[6BED4] during the ongoing development of its specification.

4. Related Protocols

The following protocols are not tunnel mechanisms mechanisms, but they can be
used in the configuration and/or setup phase of such protocols.

4.1. Tunnel Setup Protocol (TSP)

The Tunnel Setup Protocol [RFC5572] specifies a protocol for
negotiating the setup of a variety of tunnel encapsulations. In this
document
document, we are only interested in the encapsulation of IPv6 in
IPv4. The Tunnel Setup Protocol can negotiate these as a protocol 41
encapsulated tunnel or as a UDP-encapsulated tunnel. The tunnel
negotiation is performed as an XML exchange over UDP or TCP.

As a TSP client exchanges all IPv6 traffic with the same tunnel
server, there are no concerns caused by NAT implementations. The
only concern is to send regular keepalives, for which ICMPv6 ping
messages to the tunnel server are suggested. When encapsulating IPv6
packets directly in IPv4, all protocol 41 limitations apply. To
avoid these, an additional UDP header may be used.

The Tunnel Setup Protocol treats all protocols and ports for one IPv4
client address as equivalent. This suffices when protocol 41 is
used, but for UDP it creates a situation where one user can set up a
tunnel behind NAT, and another user could hijack the tunnel
privileges.

Open source

Open-source clients for the Tunnel Setup Protocol and a matching
tunnel infrastructure are provided from the freenet6 Freenet6 tunnel service
[GOGO6].

4.2. SixXS Heartbeat Protocol

The SixXS Heartbeat Protocol [I-D.massar-v6ops-heartbeat] [HEARTBEAT] allows nodes that have
intermittent connectivity or a dynamic IPv4 address that changes from
time to time to have continuing tunneled IPv6 connectivity. One of
the goals of the protocol is to determine when a node is no longer
present at its previous IPv4 address and then stop sending tunneled
packets to avoid tunneled packets prevent them from being delivered to the wrong node. The
Heartbeat Protocol then allows a tunnel broker to determine a
client's new IPv4 address and continue sending tunneled packets with
minimal interruption.

To accomplish this, a node sends periodic heartbeat packets to the
tunnel broker. If the tunnel broker fails to receive valid heartbeat
packets, it shuts down the tunnel in question. Heartbeat packets
contain an MD5 message authentication code and a timestamp to avoid
replay attacks. The Heartbeat Protocol can work with different
tunnel mechanisms, but it is often used with configured tunnels
(Section 3.1).

The protocol is implemented in the SixXS tunnel broker; client
implementations are available for common operating systems. AYIYA
can be considered the successor of the Heartbeat Protocol.

4.3. Tunnel Information and Control protocol Protocol (TIC)

The Tunnel Information and Control protocol (TIC) protocol [TIC] is the setup
protocol for the [SIXXS] tunnel broker tunnel-broker service.

With the TIC protocol protocol, a tunnel broker tunnel-broker user can request a list of
available tunnels and points-of-presence points of presence (POPs) from the tunnel tunnel-
broker service. When the user chooses one of the tunnels, the
configuration parameters for that tunnel can then be requested
through TIC. TIC also provides commands to control the tunnel, for
example
example, to change the tunnel endpoints, endpoints or to enable or disable the
tunnel.

Authentication of users is done based on username and password.
Certain tunnel mechanisms, such as AYIYA (Section 3.6) and configured
tunnels (Section 3.1) with heartbeat (Section 4.2), need a
synchronised clock between the tunnel server and the client. TIC
facilitates this by providing a server timestamp on request. The
client can use that to verify that its clock is synchronised with the
server and show an error message to the user if it is not.

The TIC protocol is implemented in the AICCU [AICCU] client software (see
[AICCU]) and in AVM Fritz!Box home routers.

5. Common Aspects

The following are aspects common to many or all tunnel mechanisms.

5.1. Protocol 41 Encapsulation

The most straightforward way to encapsulate an IPv6 packet inside an
IPv4 packet is by simply adding an IPv4 header in front of the IPv6
header. In this case, the protocol Protocol field in the IPv4 header is set
to the value 41. This encapsulation is also known as "IPv6 in IPv4"
and "IP6 Encapsulation".

This simple "protocol 41" encapsulation is used by a number of tunnel
mechanisms:

configured tunnels (Section 3.1)

automatic tunneling (Section 3.2)

6over4 (Section 3.3)

6to4 (Section 3.5)

ISATAP (Section 3.7)

6rd (Section 3.9)

5.2. NAT and Firewalls

It is not uncommon for NATs and firewalls to block protocol 41
encapsulated packets, especially at the boundary between an
organisation's internal network and the public internet. Other
tunnel Internet. Tunnel
mechanisms than that don't use protocol 41 encapsulation typically employ
a UDP header, header and are somewhat less likely to be filtered, assuming
that tunneling is initiated on the LAN-side. LAN side. UDP is usually
subjected to NAPT
[RFC2663] Network Address Port Translation (NAPT) [RFC2663], which
additionally translates between internal and external port numbers.
(Often, the term "NAT" is used where "NAPT" may be more appropriate.)

Although protocol 41 can in principle work through NAT, there are two
issues. First, when the IPv6 address is derived from the IPv4
address (see Section 5.4), NATing of the outer IPv4 header breaks the
relationship between the IPv4 and IPv6 addresses. Second, because
protocol 41 does not use port numbers, the number of protocol 41
tunnel endpoints that can be supported behind a NAT device is equal
to its number of external IPv4 addresses (see Section 6.1). This
limitation also applies to GRE.

Tunnels that pass through a NAT device or stateful firewall need to
generate traffic at regular intervals to refresh the NAT or firewall
mapping. If the mapping is lost, tunneled packets from the outside
won't be able to pass through the NAT/firewall NAT or firewall until a system
behind the NAT or firewall sends a tunneled packet and the mapping is
recreated.
re-created. Alternatively, a static mapping (often in the form of a
"default" or "DMZ" host) may be configured manually.

The following tunnel mechanisms are incompatible with NAT because
their addresses must be derived from a globally unique IPv4 address:

automatic tunneling (Section 3.2)

6to4 (Section 3.5)

6rd (Section 3.9)

LISP (Section 3.11)

Note that it is common to run 6to4 or 6rd on a home gateway device
that also performs IPv4 NAT. In this configuration, NAT is not
applied to tunneled packets, so NAT and 6to4/6rd can coexist.

The following tunnel mechanisms cannot operate between nodes on
opposing sides of a NAT, but they do work if _all_ nodes are behind a
NAT (where RFC 1918 addresses are often used):

6over4 (Section 3.3)

ISATAP (Section 3.7)

The following tunnel mechanisms may work through NAT in some
circumstances, but are not designed for NAT compatibility:

configured tunnels (Section 3.1)

GRE (Section 3.4)

The following tunnel mechanisms are designed for NAT compatibility:

AYIYA (Section 3.6)

Teredo (Section 3.8) (but 3.8); but it is unreliable) unreliable

6a44 (Section 3.10)
SEAL (Section 3.12)

6bed4 (Section 3.13)

The LISP specification requires that locator addresses (the addresses
in the outer IPv4 header) are globally routable public addresses.

A tunnel built over UDP makes a claim on a resource, namely namely, an
external UDP port. This may impact how well a tunnel will scale in
an organisation; for instance, if every desktop runs its own tunnel
client over UDP UDP, then the claim on this resource may have some
impact.

Note that ISPs may have multiple subscribers share a public IPv4
address by performing NAT (Carrier Grade NAT, CGN or CGNAT (Carrier-Grade NAT in this context). In
this case, the subscribers' home gateways may receive an address in
the 100.64.0.0/10 block [RFC6598]. For the purposes of tunnel
mechanisms, this address block is similar to the [RFC1918] RFC 1918 address
blocks. However, NAT/RFC1918 aware tunnel implementations that are aware of NAT and
RFC 1918 addresses may not recognise 100.64.0.0/10 as non-public
addresses and fail to operate successfully. The same issue is
present if an ISP decides to use regular global unicast IPv4 address
space behind a CGN.

5.3. MTU Considerations

Because of the extra IPv4 header and possible additional headers
between the IPv4 and IPv6 headers, tunnels experience a reduced
maximum packet size (Maximum Transfer Unit, MTU) (MTU) compared to native IPv6 communication.

Path MTU discovery (PMTUD) should handle this in nearly all cases,
but filtering of ICMPv6 "packet too big" messages may lead to an
inability to communicate because senders of large packets fail to
perform PMTUD successfully. However, when a tunnel terminates
directly on the host using it, the TCP maximum segment size (MSS)
option communicates the maximum packet size to the remote endpoint,
so TCP-based communication may still succeed. If not, the initial
TCP SYN/ACK exchange happens without issue, but then the session
stalls as the larger packets containing data are lost.

With tunnel mechanisms where the MTU is left unspecified, it is
possible for the two endpoints to have different MTUs: typically, one
uses the IPv6 minimum, 1280, minimum (1280 bytes), while the other uses the physical
MTU minus tunnel overhead, often 1480. overhead (often 1480 bytes). In theory, this should
lead to PMTUD failures because the "big" side unknowingly sends
packets that the "small" side can't handle. However, in practice practice,
implementations handle incoming packets larger than their own MTU
without issue.

Only when the IPv4 MTU is reduced below 1500 bytes, for instance instance,
when using PPP over Ethernet (PPPoE, [RFC2516]), issues are more
likely to arise. So So, when the possibility exists that tunneled
packets encounter a PPPoE link, it is prudent to set the MTU of a
tunnel to no more than 1472 bytes, so that tunneled packets don't
have to be fragmented. Additionally, Section 3.2.1 of [RFC4213]
recommends limiting the MTU of tunnels to the a minimum of 1280. 1280 bytes.

SEAL was specifically designed to overcome these limitations by
adding the capability to fragment IPv6 packets prior to encapsulation
in IPv4 and then reassembling to reassemble the fragments at the remote tunnel
endpoint. This way, the SEAL tunnel ensures that packets that are no
larger than 1500 bytes will be transported to the tunnel far end even
if there are restricting links in the path. SEAL can also admit
larger packets into the tunnel on a best effort best-effort basis in case the
path between the tunnel endpoints can support this larger size.

5.4. IPv4 Addresses Embedded in IPv6 Addresses

Many tunnel mechanisms embed IPv4 addresses or further information in
the IPv6 addresses they use. There are two possible reasons for
this. First, with an IPv4 address embedded in the IPv6 address, the
outer IPv4 header can be derived without a need to explicitly
configure tunnel endpoints. Automatic tunneling, 6to4, ISATAP, 6bed4
6bed4, and Teredo do this. 6over4 embeds the IPv4 address for the
second reason; it is embedded in the interface identifier, Interface Identifier and thus
the IPv6
address, because address because, that way, a (presumably) globally unique interface
identifier
Interface Identifier can be generated.

Automatic tunneling uses IPv4-compatible addresses in the prefix
::/96 (i.e., the first 96 bits are all zero).

| 96 bits | 32 |
+------------------------------------------------+-----------------+
| 0:0:0:0:0:0 | IPv4 address |
+------------------------------------------------+-----------------+

The IPv4-compatible addresses structure IPv4-Compatible Address Structure

Systems running 6to4 have addresses in the 6to4 prefix 2002::/16.

| 16 bits | 32 | 16 | 64 bits |
+--------+-----------------+--------+------------------------------+
+---------+----------------+--------+------------------------------+
| 2002 | IPv4 address | Subnet | Interface ID |
+--------+-----------------+--------+------------------------------+
+---------+----------------+--------+------------------------------+

The 6to4 address structure Address Structure
Because a 6rd domain might share a common IPv4 prefix prefix, it is not
always necessary to encode all 32 bits of the IPv4 address in the 6rd
delegated prefix. The bits that become available because of this
optimisation can be used to provide more subnet IDs to the user
and/or to use a smaller address block for the 6rd prefix.

The 6rd address structure Address Structure

6over4 uses the IPv4 address to generate a 64-bit Interface
Identifier, which can then be used to create a 128-bit IPv6 address
through Stateless Address Autoconfiguration.

| 48 bits | 16 | 32 | 32 |
+---------------------+--------+-----------------+-----------------+
| Organisation prefix | Subnet | 0:0 | IPv4 address |
+---------------------+--------+-----------------+-----------------+

The 6over4 address structure Address Structure

The ISATAP address structure is similar to the 6over4 address
structure, except that the unique/local (u) bit signifies whether the
IPv4 address in the interface identifier Interface Identifier is unique. Presumably, this
is the case for any non-[RFC1918] IPv4 address. address that is not as defined in RFC 1918.
The group (g) bit is set to zero, and the remaining bits are set to to
0x00005EFE.

| 48 bits | 16 | 32 | 32 |
+---------------------+--------+-----------------+-----------------+
| Organisation prefix | Subnet | ug00:5EFE | IPv4 address |
+---------------------+--------+-----------------+-----------------+

The ISATAP address structure Address Structure

Teredo embeds the Teredo server's IPv4 address, a number of flags,
and a UDP port number number, as well as the Teredo client's IPv4 address in
the IPv6 addresses it creates. For good measure, the UDP port and
client IPv4 address are "obfuscated" by flipping their bits.

| 32 bits | 32 | 16 | 16 | 32 |
+----------------+---------------+-------+-------+-----------------+
| 2001:0 | Server IPv4 | Flags | Port | Client IPv4 |
+----------------+---------------+-------+-------+-----------------+

The Teredo address structure Address Structure

6a44 can be seen as a combination of 6rd and Teredo. The 6a44 prefix
is given out by an ISP. Both the customer site (home gateway) IPv4
address as well as the host's/client's RFC 1918 IPv4 address and also a
port number are embedded in the IPv6 address.

| 48 bits | 32 | 16 | 32 |
+----------------------+-----------------+-------+-----------------+
| 6a44 prefix | Cust. site IPv4 | Port | Client IPv4 |
+----------------------+-----------------+-------+-----------------+

The 6a44 address structure Address Structure

6bed4 embeds two combinations of an IPv4 address and UDP port
(together acting as a "6bed4 address") in the IPv6 address; the address. The
first address is for a tunnel server that everyone is certain to reach,
reach; the other is for the direct address that most peers should be
able to reach directly. The tunnel server server, however, is the only one
with guaranteed access to the direct address.

| 64 32 bits | 32 | 50 | 14 |
+--------+-----------------------+-------------------------+-------+
+----------+---------------------+-------------------------+-------+
| prefix | general |general 6bed4 address | address| direct 6bed4 address | lanIP |
+--------+-----------------------+-------------------------+-------+
+----------+---------------------+-------------------------+-------+

The 6bed4 Address Structure

The general 6bed4 address structure

Some details of field conceals the well-known UDP port for
the 6bed4 service. The direct 6bed4 address format are still work in progress
at field includes two extra
bits to adhere to the time of this writing. EUI-64 address format. The lanIP bits are free
for local purposes, such as creating a DHCPv6 range.

6. Evaluation of Tunnel Mechanisms

The following subsections deal with the various aspects of tunnels that
guide their selection.

6.1. Efficiency of IPv4 Address Use

With the depletion of the IPv4 address space, the ability to deploy a
tunnel mechanism behind NAT as well as the number of IPv6
subscribers, subnets subnets, and individual hosts that can be supported
behind a single IPv4 address have become important considerations.

These issues are irrelevant to tunnel mechanisms that provide IPv6
connectivity between hosts within the same administrative domain,
such as ISATAP or 6over4, as they can use private IPv4 addresses.
This is also true for 6rd, which 6rd; it is used between an ISP and its
customers' home gateways when the ISP has implemented NAT.

6to4 cannot work behind any kind of NAT. Most other mechanisms based
on protocol 41 can work behind NAT, at least in principle. In
practice
practice, this difference is not as big as because the protocol 41
encapsulation doesn't provide any fields that allow a NAT to
demultiplex tunneled packets. This means that only a single protocol
41 tunnel endpoint can be supported for each public IPv4 address.

This makes configured tunnels (as well as 6to4) incompatible with
service provider operated
service-provider-operated NATs, where multiple subscribers share an
IPv4 address.

Teredo, 6a44, 6bed4, AYIYA, SEAL SEAL, and TSP are designed to work
through NATs and use a UDP header, so multiple tunnel endpoints can
be hosted behind a single IPv4 address. On the other hand, Teredo
only provides IPv6 connectivity to a single host.

The following table shows how many IPv4 addresses each tunnel
mechanism requires and how many IPv6 hosts it can connect. The
mechanisms are listed in order of increasing numbers of supported
IPv6 hosts per IPv4 address.

Tunneled IPv6 hosts Hosts per IPv4 address Address

(*) Although Teredo is designed for NAT compatibility, it doesn't
work through all existing NATs.

6.2. Supported Network Topologies

There are two ways to use an IPv6-in-IPv4 tunnel to connect to the
IPv6 internet: Internet: using a point-to-point tunnel to a tunnel broker or an
ISP-operated gateway, or using a non-broadcast multiple access Non-Broadcast Multi-Access (NBMA)
tunnel and anycasted public gateways or relays.

The advantages of the point-to-point model are predictable
performance and flexibility regarding the IPv6 addresses used. The
advantage of the NBMA model is that traffic between two hosts or
networks that both use the mechanism can flow directly without
passing through a gateway (direct peer-to-peer communication.). communication). An
extra advantage of the NBMA model with public gateways is automatic
configuration and no involvement from an ISP.

Unfortunately, the advantages of this NBMA public anycast model come
at a price: both the peer-to-peer connectivity between tunnel users
and the connectivity towards the native IPv6 internet Internet may suffer from
reliability and performance issues.

The anycast mechanism allows tunnel users to utilise the nearest
gateway to connect to the IPv6 internet Internet by simply giving each gateway
the same address. Routing protocols then select the lowest-cost (and
presumably, shortest) path towards a gateway. However, this makes
the path taken by tunneled packets hard to predict or influence. It
is common for traffic in two directions to use different gateways,
complicating debugging even further. Because nobody is in charge or
gets paid for operating a gateway, the number of public gateways is
lower than would be ideal. This increases the distance to the
nearest gateway for some users. There is also the possibility that
gateways encounter more traffic than they can handle.

The advantage of a tunnel provided by an ISP or tunnelbroker tunnel broker is that
there is a clear responsibility for providing a good service with
well maintained
well-maintained gateways.

Topologies Supported per Tunnel Mechanism

6.3. Robustness

Tunnels may fail for three main reasons: when tunneled packets are
filtered, typically by a firewall, firewall; when a tunnel endpoint IPv4
address changes changes; or when tunneled packets are filtered or because of
NAT issues.

If a tunnel endpoint gets a new address, the other side of the tunnel
needs to know to send packets to the new address. With mechanisms
that derive IPv6 addresses from the IPv4 address, the previous IPv6
addresses become unreachable unreachable, and new IPv6 addresses must be
configured.

Some tunnel mechanisms don't work through NAT, or are limited when
working through NAT. NAT mappings can typically only be created by
traffic from the "inside" to the "outside", not by traffic from
outside the NAT to the network behind the NAT.

Point-to-point tunnel mechanisms either work consistently or they
always fail. As such, a simple ping to the other side of the tunnel
is sufficient to learn its state. Also, point-to-point tunnels may
support routing protocols, which can automatically reroute traffic
around a failed tunnel.

Some tunnel mechanisms use a public gateway to reach the native IPv6
internet.
Internet. Public gateways may or may not be operational and/or
reachable, and they may have limited performance, depending on
distance and usage.

Tunnel mechanisms that use a broadcast or non-broadcast multiple
access Non-Broadcast Multi-Access
(NBMA) communication model may experience failures between some
combinations of tunnel endpoints and not others.

The following table lists tunnel mechanisms that provide connectivity
to the IPv6 internet Internet in order of decreasing robustness. (However,
even less-robust mechanisms may function well in suitable
environments.)

Susceptibility of tunnel mechanisms Tunnel Mechanisms to problems Problems
Notes:

(1): only Only one protocol 41 tunnel endpoint can receive a NAT mapping
behind a NAT using a single public IPv4 address. Additional
endpoints will not receive incoming packets. When a tunnel
endpoint changes its internal address, the old NAT mapping
needs to time out before a new one can be created.

(2): 6to4 implementations automatically disable the mechanism when
the system has an RFC 1918 address. However, 6to4 may remain
enabled and be non-operational when ISPs apply NAT using non-RFC
1918
addresses that are not as defined in RFC 1918 [RFC6598].

(3): whether Whether Teredo can obtain an address depends on the type of NAT
it detects. Whether Teredo functions at such an address
depends on the accuracy of that determination, which is founded
on an incomplete model of NAT.

On some widely used implementations, 6to4 has been enabled by default
without checking whether there was connectivity to the anycasted
public gateway address. As a result, 6to4-derived connectivity to
the IPv6 internet Internet was often found to be broken because of protocol 41
filtering. Because of this, many operating systems now try to avoid
using IPv6 over 6to4. See [RFC6343].

Also see [TERTST] for more information about the robustness of
Teredo.

There is not a single tunnel mechanism that is more robust in all
possible ways than every other tunnel mechanism. However, in general
general, mechanisms that use public gateways and peer-to-peer
tunneling tend to have the most issues. Configured tunnels tunnels, on the
other hand, often work very well, especially if there is no NAT on
the path, but they may need administrative intervention when a tunnel
endpoint address changes.

6.4. Gateway State

There is an additional consideration that is important to operators
of gateways that connect IPv6-in-IPv4 tunnels to the IPv6 internet: Internet:
how much state a tunnel mechanism requires.

6to4

6to4, 6rd, 6a44 and 6rd 6bed4 require no state at all: when encapsulating
IPv6 packets inside an IPv4 packet, the IPv4 destination address is
directly copied from bits in the IPv6 destination address. This
makes all possible tunneled destinations directly reachable through a
single virtual interface.

Teredo, 6a44

Teredo relays maintain a list of peers and 6bed4 require additional logic to work through NATs,
which requires them are intended to keep track of relatively volatile state. They
also work on a per-host basis rather than allowing service a
limited number of hosts
to make use of hosts. The Teredo server, however, is a single tunnel. stateless
gateway component.

With configured tunnels, GRE, AYIYA AYIYA, and SEAL SEAL, there is no direct
mapping from (part of) the IPv6 destination address to the IPv4
destination address. A typical implementation of these mechanisms is
by having
has a virtual tunnel interface for each tunnel. Packets are
forwarded to the correct virtual interface through a routing table
lookup. Routing tables can grow very large and remain fast, so the
number of virtual interfaces tends to be the limiting factor for
tunnel gateways. AYIYA and the SixXS Heartbeat Protocol also keep
track of the reachability status of each tunnel.

6.5. Performance

There are several reasons why tunneled connectivity may perform
inferior to native, un-tunneled untunneled connectivity. Inherently, tunnels add
one or more extra headers, and therefore increase overhead. However,
for a an Ethernet packet of maximum size (1500 bytes) Ethernet packet bytes), the additional
overhead of an IPv4 header is only 1.3%.

The process of encapsulation is not inherently slow, but in some
implementations, it may be. Larger routers that normally forward
packets using special purpose hardware, special-purpose hardware often don't have high high-
performance CPUs. If then tunnel encapsulation must then be done by that
relatively slow CPU, performance will be worse than regular hardware-
based packet forwarding.

The path that tunneled packets take can be longer than the path that
untunneled packets would take. (Increased take (i.e., increased path stretch.) stretch can
occur). This may or may not lead to decreased performance.

+------------+-----------------+----------------------+-------------+
| Mechanism | Overhead | Increased path | Variability |
| | (bytes) | stretch | |
+------------+-----------------+----------------------+-------------+
| Conf. tun. | 20 | may be large | none |
| Auto. tun. | 20 | none | none |
| 6over4 | 20 | none | none |
| GRE | 28 - 36 | may be large | none |
| 6to4 | 20 | may be large | high |
| AYIYA | 72 | may be large | low |
| ISATAP | 20 | none | none |
| Teredo | 28 - 36 | may be large | high |
| 6rd | 20 | small | low |
| 6a44 | 20 - 28 | small | low |
| 6bed4 | 28 | may be large | high |
| LISP | 36 | small | low |
| SEAL | 24 - variable | small | low |
+------------+-----------------+----------------------+-------------+

Typical tunnel performance Tunnel Performance

7. IANA considerations

None.

8. Security considerations Considerations

There are many security considerations with tunneling. An important
one is that through a tunnel, connectivity to the IPv6 internet Internet may
exist even though network administrators did not intend for it to be
there. "Security Concerns with IP Tunneling" [RFC6169] discusses
this issue in detail.

Although

Although, in principle, ingress filtering (BCP 38, [RFC2827]) is
possible with tunnels, in practice, it is relatively easy for spoofed
packets to make their way through a tunnel. Not only is it often
easy to spoof the outer IPv4 header and make false IPv6 packets seem
to originate from a tunnel broker or gateway, it may also be possible
for an attacker to route false IPv6 packets through a legitimate
tunnel broker or gateway. Many tunneling protocols have various
means of detecting and rejecting such packets, while others have
limited or no such provisions. For instance, see [RFC3964] for how
this can be addressed with 6to4.

So it is important to recognise that unless special measures are
taken (like [RFC4301]), both IPv4 and IPv6 addresses in tunnel
packets may be spoofed and cannot be relied upon for access controls.
Such spoofing was used successfully to discover IPv6-in-IPv4 tunnels
in [TUNDISC].

Tunnels may also be used by third parties to obfuscate their
activities or perform amplification attacks. To avoid contributing
to this problem, it is important to make sure only locally generated
packets with legitimate addresses are sent out over tunnels.

8. Contributors

Job Snijders contributed text to the points of comparison. Fred
Templin provided the text for SEAL and contributed to the security
considerations. Jeroen Massar, Brian Carpenter, Tina Tsou, John
Mann, Suresh Krishnan, Victor Kuarsingh, Dan Jones, Nejc Skoberne Skoberne,
and Fred Baker reviewed the document and/or offered suggestions for
improvement.

10.

9. Acknowledgements

We wish to thank SURFnet and Rogier Spoor for commissioning this
work; both their initiative and funding has have helped this document to
be written.

11.

10. Informative References

[6BED4] Van Rein, R., "6bed4: Peer-to-Peer IPv6 on Any
Internetwork", <http://devel.0cpm.org/6bed4/>. Work in Progress, July 2013.

[AICCU] SixXS, "Automatic IPv6 Connectivity Client Utility
(AICCU)", <http://www.sixxs.net/tools/aiccu/>.

[AYIYA] SixXS, "Anything In Anything (AYIYA)",
<http://www.sixxs.net/tools/ayiya/>.

[GOGO6] gogo6, "Freenet6: Free and Easy IPv6 Connectivity",
<http://www.gogo6.com/freenet6>.

[I-D.ietf-softwire-map]

[HEARTBEAT] Massar, J., "SixXS Heartbeat Protocol", Work in Progress,
June 2005.

[LISPBETA] LISP4/LISP6.net, "LISP Beta Network",
<http://www.lisp4.net/beta-network/>.

[MAP] Troan, O., Dec, W., Li, X., Bao, C., Matsushima, S.,
Murakami, T., and T. Taylor, "Mapping of Address and Port
with Encapsulation (MAP)", draft-ietf-softwire-map-07
(work Work in progress), May Progress, August 2013.

[I-D.massar-v6ops-ayiya]

[MASSAR] Massar, J., "AYIYA: Anything In Anything",
draft-massar-v6ops-ayiya-02 (work Work in progress),
Progress, July 2004.

[I-D.massar-v6ops-heartbeat]
Massar, J., "SixXS Heartbeat Protocol",
draft-massar-v6ops-heartbeat-01 (work in progress),
June 2005.

[I-D.templin-intarea-seal]
Templin, F., "The Subnetwork Encapsulation and Adaptation
Layer (SEAL)", draft-templin-intarea-seal-55 (work in
progress), May 2013.

[LISPBETA]
"LISP Beta Network", <http://www.lisp4.net/beta-network/>.

[RFC1191] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191,
November 1990.

[RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G.,
and E. Lear, "Address Allocation for Private Internets",
BCP 5, RFC 1918, February 1996.

[RFC1933] Gilligan, R. and E. Nordmark, "Transition Mechanisms for
IPv6 Hosts and Routers", RFC 1933, April 1996.

[RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU
Discovery for IP version 6", RFC 1981, August 1996.

[RFC2516] Mamakos, L., Lidl, K., Evarts, J., Carrel, D., Simone,
D., and R. Wheeler, "A Method for Transmitting PPP Over
Ethernet (PPPoE)", RFC 2516, February 1999.

[RFC2529] Carpenter, B. and C. Jung, "Transmission of IPv6 over
IPv4 Domains without Explicit Tunnels", RFC 2529,
March 1999.

[RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address
Translator (NAT) Terminology and Considerations",
RFC 2663, August 1999.

[RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P.
Traina, "Generic Routing Encapsulation (GRE)", RFC 2784,
March 2000.

[RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering:
Defeating Denial of Service Attacks which employ IP
Source Address Spoofing", BCP 38, RFC 2827, May 2000.

[RFC2893] Gilligan, R. and E. Nordmark, "Transition Mechanisms for
IPv6 Hosts and Routers", RFC 2893, August 2000.

[RFC3056] Carpenter, B. and K. Moore, "Connection of IPv6 Domains
via IPv4 Clouds", RFC 3056, February 2001.

[RFC3068] Huitema, C., "An Anycast Prefix for 6to4 Relay Routers",
RFC 3068, June 2001.

[RFC3489] Rosenberg, J., Weinberger, J., Huitema, C., and R. Mahy,
"STUN - Simple Traversal of User Datagram Protocol (UDP)
Through Network Address Translators (NATs)", RFC 3489,
March 2003.

[RFC3964] Savola, P. and C. Patel, "Security Considerations for
6to4", RFC 3964, December 2004.

[RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition
Mechanisms for IPv6 Hosts and Routers", RFC 4213,
October 2005.

[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.

[RFC4380] Huitema, C., "Teredo: Tunneling IPv6 over UDP through
Network Address Translations (NATs)", RFC 4380,
February 2006.

[RFC4787] Audet, F. and C. Jennings, "Network Address Translation
(NAT) Behavioral Requirements for Unicast UDP", BCP 127,
RFC 4787, January 2007.

[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
September 2007.

[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862, September 2007.

[RFC4891] Graveman, R., Parthasarathy, M., Savola, P., and H.
Tschofenig, "Using IPsec to Secure IPv6-in-IPv4 Tunnels",
RFC 4891, May 2007.

[RFC5214] Templin, F., Gleeson, T., and D. Thaler, "Intra-Site
Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214,
March 2008.

[RFC5389] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing,
"Session Traversal Utilities for NAT (STUN)", RFC 5389,
October 2008.

[RFC5572] Blanchet, M. and F. Parent, "IPv6 Tunnel Broker with the
Tunnel Setup Protocol (TSP)", RFC 5572, February 2010.

[RFC5969] Townsley, W. and O. Troan, "IPv6 Rapid Deployment on IPv4
Infrastructures (6rd) -- Protocol Specification",
RFC 5969, August 2010.

[RFC6145] Li, X., Bao, C., and F. Baker, "IP/ICMP Translation
Algorithm", RFC 6145, April 2011.

[RFC6169] Krishnan, S., Thaler, D., and J. Hoagland, "Security
Concerns with IP Tunneling", RFC 6169, April 2011.

[RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual-
Stack Lite Broadband Deployments Following IPv4
Exhaustion", RFC 6333, August 2011.

[RFC6343] Carpenter, B., "Advisory Guidelines for 6to4 Deployment",
RFC 6343, August 2011.

[RFC6598] Weil, J., Kuarsingh, V., Donley, C., Liljenstolpe, C.,
and M. Azinger, "IANA-Reserved IPv4 Prefix for Shared
Address Space", BCP 153, RFC 6598, April 2012.

[RFC6724] Thaler, D., Draves, R., Matsumoto, A., and T. Chown,
"Default Address Selection for Internet Protocol Version
6 (IPv6)", RFC 6724, September 2012.

[RFC6732] Kuarsingh, V., Lee, Y., and O. Vautrin, "6to4 Provider
Managed Tunnels", RFC 6732, September 2012.

[RFC6751] Despres, R., Carpenter, B., Wing, D., and S. Jiang,
"Native IPv6 behind IPv4-to-IPv4 NAT Customer Premises
Equipment (6a44)", RFC 6751, October 2012.

[RFC6830] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis, "The
Locator/ID Separation Protocol (LISP)", RFC 6830,
January 2013.

[RFC6832] Lewis, D., Meyer, D., Farinacci, D., and V. Fuller,
"Interworking between Locator/ID Separation Protocol
(LISP) and Non-LISP Sites", RFC 6832, January 2013.

[RFC6833] Fuller, V. and D. Farinacci, "Locator/ID Separation
Protocol (LISP) Map-Server Interface", RFC 6833,
January 2013.

[SEAL] Templin, F., "The Subnetwork Encapsulation and Adaptation
Layer (SEAL)", Work in Progress, October 2013.

[SIXXS] Massar, J. and P. van Pelt, "IPv6 Deployment & Tunnel
Broker", <http://www.sixxs.net/>.

[TERTST] Huston, G., "Testing Teredo", April 2011,
<http://www.potaroo.net/ispcol/2011-04/teredo.html>.

[TIC] SixXS, "Tunnel Information and Control protocol (TIC)",
<http://www.sixxs.net/tools/tic/>.

[TR-069] The Broadband Forum, "CPE WAN Management Protocol",
July 2011, <http://www.broadband-forum.org/technical/
download/TR-069_Amendment-4.pdf>.

[TUNBROKER] Hurricane Electric, "Hurricane Electric Free IPv6 Tunnel
Broker", <http://www.tunnelbroker.net/>.

[TUNDISC] Colitti, L., Di Battista, G., and M. Patrignani,
"IPv6-in- IPv4 tunnel discovery: methods and experimental
results", IEEE eTransactions on Network and Service
Management
(eTNSM) (eTNSM), vol. 1, no. 1, pag. p. 2-10, April 2004.

Appendix A. Evaluation Criteria

Each type of tunnel has specific advantages and disadvantages. We
have considered the following points when evaluating the different
protocols. Not every point is mentioned in each section where a
protocol is described, only those that are specifically relevant to
that protocol.

Protocol overhead: How much overhead does the tunneling protocol
cause? There are two factors that play a role: the number of
interactions to set up the tunnel and the packet header size
causing a lower MTU and/or fragmentation.

Automatic configuration: Does this protocol require manual
configuration at the endpoints?

Predictability: How predictable is the functioning of the protocol?

Single host or network: Is this protocol intended to be used by a
single host or by a router that then provides IPv6 connectivity to
multiple hosts?

Load balancing: Does the tunnel traffic have enough entropy and/or
hashability
"hashability" to be able to be load-balanced over multiple links,
or do all tunnel packets have the same outer 5-tuple?

Path stretch: Does the tunnel optimise the route, or is there a big
potential for a much longer path when using the tunnel?

NAT traversal: Can the tunnel pass through a NAT gateway, and does
it require configuration on that NAT gateway?

Tunnel endpoint mobility: Are the IPv4 addresses of the tunnel fixed
fixed, or do they adjust automatically when an endpoint moves. moves?

State: Are the endpoints required to keep state for the tunnel tunnel, or
is the tunnel stateless?

Network type: Is this network a point-to-point or NBMA type of
network?

Purpose: What is the intended purpose of this tunnel protocol?

Related protocols: To which protocols is this tunnel protocol
related? Are there alternatives?

Implementations: Is this protocol supported on the major operating
systems, routers routers, and firewalls?
Limitations: What are the known limitations of this protocol?

Authors' Addresses

Sander Steffann
S.J.M. Steffann Consultancy
Tienwoningenweg 46
Apeldoorn, Gelderland 7312 DN
The Netherlands

Email:

EMail: sander@steffann.nl

Iljitsch van Beijnum
Institute IMDEA Networks
Avda. del Mar Mediterraneo, 22
Leganes, Madrid 28918
Spain

Email:

EMail: iljitsch@muada.com

Rick van Rein
OpenFortress
Haarlebrink 5
Enschede, Overijssel 7544 WP
The Netherlands

Email:

EMail: rick@openfortress.nl