wdiff rfc7086.original rfc7086.txt

HIP Working Group
Internet Engineering Task Force (IETF) A. Keranen
Internet-Draft
Request for Comments: 7086 G. Camarillo
Intended status:
Category: Experimental J. Maenpaa
Expires: April 14, 2014
ISSN: 2070-1721 Ericsson
October 11, 2013
January 2014

Host Identity Protocol-Based Overlay Networking Environment (HIP BONE)
Instance Specification for REsource LOcation And Discovery (RELOAD)
draft-ietf-hip-reload-instance-10

Abstract

This document is the Host Identity Protocol-Based HIP-Based Overlay Networking Environment (HIP
BONE) instance specification for the REsource LOcation And Discovery
(RELOAD) protocol. The document provides the details needed to build
a RELOAD-based overlay that uses HIP.

Status of This Memo

This Internet-Draft document is submitted in full conformance with the
provisions of BCP 78 not an Internet Standards Track specification; it is
published for examination, experimental implementation, and BCP 79.

Internet-Drafts are working documents
evaluation.

This document defines an Experimental Protocol for the Internet
community. This document is a product of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF
community. It has received public review and has been approved for
publication by the Internet Engineering Steering Group (IESG). Not
all documents approved by the IESG are a maximum candidate for any level of six months
Internet Standard; see Section 2 of RFC 5741.

Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on April 14, 2014.
http://www.rfc-editor.org/info/rfc7086.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Peer Protocol . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Node ID Generation . . . . . . . . . . . . . . . . . . . . . 3
5. Mapping between Protocol Primitives and HIP Messages . . . . 3
5.1. Forwarding Header . . . . . . . . . . . . . . . . . . . . 4
5.2. Security Block . . . . . . . . . . . . . . . . . . . . . 4
5.3. Replaced RELOAD Messages . . . . . . . . . . . . . . . . 5
6. Securing Communication . . . . . . . . . . . . . . . . . . . 5
7. Routing HIP Messages via the Overlay . . . . . . . . . . . . 6 5
8. Enrollment and Bootstrapping . . . . . . . . . . . . . . . . 6
9. NAT Traversal . . . . . . . . . . . . . . . . . . . . . . . . 7
10. RELOAD Overlay Configuration Document Extension . . . . . . . 7
11. Security Considerations . . . . . . . . . . . . . . . . . . . 8
12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
13. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 8
14. References . . . . . . . . . . . . . . . . . . . . . . . . . 8
14.1. Normative References . . . . . . . . . . . . . . . . . . 8
14.2. Informational Informative References . . . . . . . . . . . . . . . . 9
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 9

1. Introduction

The Host Identify Protocol-Based HIP-Based Overlay Networking Environment (HIP BONE) specification
[RFC6079] provides a high-level framework for building HIP-based
[RFC5201] overlays. The HIP BONE framework leaves does not address the
specification of the details on how to combine a particular peer
protocol with HIP to build an overlay overlay. It leaves this up to
documents referred to as HIP BONE instance specifications. As
discussed in [RFC6079], a HIP BONE instance specification needs to
define, minimally:

o the peer protocol to be used.

o what kind of Node IDs are used and how they are derived.

o which peer protocol primitives trigger HIP messages.

o how the overlay identifier is generated.

This document addresses all the previous items and provides
additional details needed to build RELOAD-based HIP BONEs, referred
to here as RELOAD HIP BONEs. The details on how different RELOAD
modules would be integrated to a HIP implementation and what kind of
APIs are used between them are left as implementation details or to
be defined by other documents.

2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119]. In
addition, this document uses the terms defined in [RFC5201],
[RFC6079], [RFC6028], and [I-D.ietf-p2psip-base]. [RFC6940].

3. Peer Protocol

The peer protocol to be used is REsource LOcation And Discovery
(RELOAD) [I-D.ietf-p2psip-base]. [RFC6940]. When used with RELOAD, HIP replaces the RELOAD's
Forwarding and Link Management Layer (described in Section 6.5 of [I-D.ietf-p2psip-base]).
[RFC6940]).

4. Node ID Generation

This document specifies two modes for generating Node and Resource
IDs. Which mode is used in an actual overlay is defined by the
overlay configuration. Both of the modes are based on 16-byte ID
mode of RELOAD, and hence RELOAD; hence, only 16-byte RELOAD Node and Resource IDs MUST
be used in a RELOAD HIP BONE.

HIP uses 128-bit Overlay Routable Cryptographic Hash Identifiers
(ORCHIDs) [RFC4843] as identifiers. In a RELOAD HIP BONE BONE, a peer's
ORCHID can be used as such as a RELOAD Node ID (the "ORCHID" mode). In this mode
mode, all the RELOAD IDs, including Resource IDs, are prefixed with
the ORCHID prefix prefix, and the lower 100 bits of the IDs defined by
RELOAD usage documents are used after the prefix.

In the other Node ID mode, namely "RELOAD", all 128 bits are
generated as defined in [I-D.ietf-p2psip-base]. [RFC6940]. This results in a larger usable
address space than using the ORCHID mode, but the resulting Node IDs
cannot be used with legacy applications and APIs, as discussed in
Section 5.1 of [RFC6079].

5. Mapping between Protocol Primitives and HIP Messages

RELOAD HIP BONE replaces the RELOAD protocol primitives taking care
of connection establishment with the HIP base exchange, whereas the
rest of the RELOAD messages are conveyed within HIP messages. The
Forwarding and Link Management Layer functionality of RELOAD,
including all the NAT traversal functionality, is replaced by HIP,
existing extensions of HIP, and the extensions defined in this
document.

The standard RELOAD messages consist of three parts: Forwarding
Header, Message Contents the forwarding
header, the message contents, and the Security Block. security block. When RELOAD
messages are sent in a RELOAD HIP BONE overlay, the RELOAD Message
Contents message
contents are used as such within HIP DATA [RFC6078] messages, but the
functionality of the Forwarding Header forwarding header and Security Block security block are
replaced with the HIP header, HIP Destination and Via lists
[RFC6028],
and CERT [RFC6253], TRANSACTION_ID [RFC6078], and the
OVERLAY_ID and OVERLAY_TTL [RFC6079] parameters, as defined in the
following sections.

5.1. Forwarding Header

The RELOAD Forwarding Header forwarding header is used for forwarding messages between
peers and to their final destination. The Forwarding Header's forwarding header's
overlay field value MUST be used as such in an OVERLAY_ID parameter
and the transaction_id field in a TRANSACTION_ID parameter. That is,
all RELOAD HIP BONE messages MUST contain these parameters and parameters; and, the
length of the OVERLAY_ID parameter's identifier field is 4 4, and the
length of the TRANSACTION_ID parameter is 8 octets. HIP Destination
and Via lists are used for the same purpose as the destination_list
and via_list in the Forwarding Header, forwarding header, with the exception that all
Resource IDs MUST be of the same length as Node IDs IDs, and compressed
IDs MUST NOT be used. The TTL Time to Live (TTL) value in the
OVERLAY_TTL parameter is used like the ttl field in the Forwarding Header. forwarding
header.

The functionality of the fragment and length fields are provided by
the HIP headers. The relo_token, version, and max_response_length
are not needed with HIP and HIP. The forwarding header's options field, if
needed eventually for some extensions, can be replaced substituted with
additional HIP parameters.

5.2. Security Block

The RELOAD Security Block security block contains certificates and digital
signatures of the message. All the HIP DATA messages are digitally
signed by the originator of the message and contain the HOST_ID
parameter with the identifier that can be used for verifying the
signature. Certificates are delivered in a HIP CERT parameter as
defined in [RFC6253] or stored to the overlay using the RELOAD
Certificate Storage Usage.

Note that when the RELOAD mode for Node ID generation is used, the
certificate certifying that a host is allowed to use a certain Node
ID MUST contain the host's Node ID instead of HIT the Host Identity Tag
(HIT) in the "Subject
Alternative Name" "subjectAltName" field of the certificate as described
in Section 11.3 of
[I-D.ietf-p2psip-base] [RFC6940], while the "Subject" field contains the
HIT calculated from the Host Identity.

5.3. Replaced RELOAD Messages

The Attach procedure in RELOAD establishes a connection between two
peers. This procedure is performed using the AttachReq and AttachAns
messages. When HIP is used, the Attach procedure is performed by
using a HIP base exchange. That is, peers send HIP I1 first Initiator
(I1) messages instead of RELOAD AttachReq messages. This behavior
replaces the one described in Section 6.5 of [I-D.ietf-p2psip-base]. [RFC6940].

The AppAttach procedure in RELOAD is used for creating a connection
for other applications than RELOAD. Also Also, the AppAttach procedure is
replaced with the HIP base exchange and, exchange, and after the base exchange,
peers can exchange any application layer data using the normal
transport layer ports over the NAT traversing IPsec connection.

This specification does not support flooding of configuration files,
so ConfigUpdate requests and responses (Section 6.5.4 of
[I-D.ietf-p2psip-base]) [RFC6940])
MUST NOT be sent in the overlay. RELOAD Ping messages (Section 6.5.3
of [I-D.ietf-p2psip-base]) [RFC6940]) MAY be used.

For all other RELOAD messages messages, the Message Contents message contents are used as such
within HIP DATA messages.

6. Securing Communication

RELOAD uses TLS Transport Layer Security (TLS) [RFC5246] connections for
securing the hop-by-hop messaging and certificates and signatures for
providing integrity protection for the overlay messages and for the
data stored in the overlay.

With a RELOAD HIP BONE, instead of using TLS connections as defined
in [I-D.ietf-p2psip-base], [RFC6940], all HIP overlay messages MUST be sent using encrypted
connections [RFC6261].

The data objects stored in the RELOAD HIP BONE overlay are signed signed,
and the signatures are stored as defined in [I-D.ietf-p2psip-base] [RFC6940] with the
exception that SignerIdentity is carried in the HIP DATA message's
HOST_ID parameter instead of using the RELOAD
SecurityBlock. security block. Where
certificates are needed, they are sent using the HIP CERT parameter.

7. Routing HIP Messages via the Overlay

If a host has no valid locator for the receiver of a new HIP packet,
and the receiver is part of a RELOAD HIP BONE overlay the host is
participating in, the host can send the HIP packet to the receiver
using the overlay routing.

When sending a HIP packet via the overlay, the host MUST add an empty
ROUTE_VIA parameter [RFC6028] to the packet with the SYMMETRIC and
MUST_FOLLOW flags set and an OVERLAY_ID parameter containing the
identifier of the right overlay network. The host consults the
RELOAD Topology Plugin for the next hop and sends the HIP packet to
that host.

An intermediate host receiving a HIP packet with the OVERLAY_ID
parameter checks if it is participating in that overlay, overlay and SHOULD
drop packets sent to unknown overlays. If the host is not the final
destination of the packet (i.e., the Receiver HIT in the HIP header
does not match to any of its HITs), it checks if the packet contains
a ROUTE_DST parameter. Such packets are forwarded to the next hop as
specified in [RFC6028]. If the packet does not contain a ROUTE_DST
parameter, the host finds the next hop from the RELOAD Topology
Plugin and forwards the packet there. As specified in [RFC6028], the
host adds the HIT it uses on the HIP association with the next hop next-hop
host to the end of the ROUTE_VIA parameter, if present.

When the final destination host receives the HIP packet, the host
processes it as specified in [RFC5201] and in case of [RFC5201]; and, if the packet is a HIP
DATA packet, the contents are processed as specified in
[I-D.ietf-p2psip-base]. [RFC6940].
If the HIP packet generates a response, the response is routed back
on the same path using the ROUTE_DST parameter as specified in
[RFC6028].

8. Enrollment and Bootstrapping

The RELOAD HIP BONE instance uses the enrollment and bootstrap
procedure defined by RELOAD [I-D.ietf-p2psip-base] [RFC6940] with the exceptions listed
below.

o In RELOAD, a node wishing to enroll in an overlay starts with
obtaining a configuration document as explained in
[I-D.ietf-p2psip-base]. [RFC6940].
This specification extends the RELOAD overlay configuration
document as defined in Section 10.

o The X.509 certificates used by the RELOAD HIP BONE instance are
similar to those of RELOAD except that they contain HITs instead
of RELOAD URIs. The HITs are included in the SubjectAltName field
of the certificate as described in [RFC6253].

o When contacting a bootstrap node, instead of forming a DTLS Datagram
Transport Layer Security (DTLS) or TLS connection, the host MUST
perform a HIP base exchange with the bootstrap node. The base
exchange MAY be performed using a HIP rendezvous or relay server.

9. NAT Traversal

RELOAD relies on the Forwarding and Link Management Layer providing
NAT traversal capabilities. Thus, the RELOAD HIP BONE instance
implementations MUST implement some reliable NAT traversal mechanism.
To maximize interoperability, all implementations SHOULD implement at
least [RFC5770].

HIP relay servers are not necessarily needed with this HIP BONE
instance since the overlay network can be used for relaying the Base
Exchange base
exchange, and further HIP signaling can be done directly between the
peers. However, if it is possible that a bootstrap peer is behind a
NAT, it MUST register with a HIP relay so that there is a reliable
way to connect to it.

10. RELOAD Overlay Configuration Document Extension

This document modifies the bootstrap-node element of the RELOAD
overlay configuration document. The modified bootstrap-node element
contains the following attributes:

address: The locator of the bootstrap node.

port: The HIP port of the bootstrap node.

hit: The HIT of the bootstrap node.

If the bootstrap-node element does not contain a HIT, the
opportunistic mode (as specified in [RFC5201]) SHOULD be used for
contacting the bootstrap node. If the element does not contain a
port number, the bootstrap node SHOULD be contacted by starting the
base exchange as defined in [RFC5201]. Otherwise, the base exchange
MUST be started UDP-encapsulated with UDP encapsulation, as defined in [RFC5770] [RFC5770],
using the given port as the destination port number.

A RELOAD HIP BONE overlay MUST use the Overlay Link Protocol type
"HIP" in the configuration document's overlay-link-protocol element.
The enrolling node MUST check the overlay-link-protocol element and
proceed with procedures defined in this document only if the "HIP"
link type is found.

This document also adds a new element inside the configuration
element that defines which mode (see Section 4) is used for
generating the Node and Resource IDs. The name of the element is
"hipbone-id-mode" and the content is the identifier of the mode:
"ORCHID" for the ORCHID prefixed IDs and "RELOAD" for the IDs that
use the whole 128 bits as defined by the RELOAD specification. The
NodeIdLength MUST be set to 16 in the configuration document document, and the
16 bytes are used, depending on the generation mode, as defined in
Section 4.

11. Security Considerations

The security considerations of RELOAD (Section 13 of
[I-D.ietf-p2psip-base]), [RFC6940]), with
the exception of TLS specific TLS-specific features,
apply also apply to RELOAD HIP BONE
instances.

Limiting the Node ID and Resource ID space into 128 bits (or 100 bits
with ORCHID prefixes) results in a higher probability for ID
collisions, both unintentional and intentional, than using larger
address spaces.

12. IANA Considerations

This section is to be interpreted according to [RFC5226].

IANA is requested to update has updated the "Overlay "RELOAD Overlay Link Protocol" registry
[I-D.ietf-p2psip-base] Protocol Registry"
[RFC6940] by assigning the new Overlay Link Protocol type "HIP" (see
Section 10).

13. Acknowledgements

Tom Henderson, Spencer Dawkins, and Christer Holmberg have provided
valuable reviews and comments on the draft. document.

14. References

14.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.

[RFC4843] Nikander, P., Laganier, J., and F. Dupont, "An IPv6 Prefix
for Overlay Routable Cryptographic Hash Identifiers
(ORCHID)", RFC 4843, April 2007.

[RFC5201] Moskowitz, R., Nikander, P., Jokela, P., and T. Henderson,
"Host Identity Protocol", RFC 5201, April 2008.

[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.

[RFC5770] Komu, M., Henderson, T., Tschofenig, H., Melen, J., and A.
Keranen, "Basic Host Identity Protocol (HIP) Extensions
for Traversal of Network Address Translators", RFC 5770,
April 2010.

[RFC6028] Camarillo, G. and A. Keranen, "Host Identity Protocol
(HIP) Multi-Hop Routing Extension", RFC 6028, October
2010.

[RFC6078] Camarillo, G. and J. Melen, "Host Identity Protocol (HIP)
Immediate Carriage and Conveyance of Upper-Layer Protocol
Signaling (HICCUPS)", RFC 6078, January 2011.

[RFC6079] Camarillo, G., Nikander, P., Hautakorpi, J., Keranen, A.,
and A. Johnston, "HIP BONE: Host Identity Protocol (HIP)
Based Overlay Networking Environment (BONE)", RFC 6079,
January 2011.

[RFC6253] Heer, T. and S. Varjonen, "Host Identity Protocol
Certificates", RFC 6253, May 2011.

[RFC6261] Keranen, A., "Encrypted Signaling Transport Modes for the
Host Identity Protocol", RFC 6261, May 2011.

[I-D.ietf-p2psip-base]

[RFC6940] Jennings, C., Lowekamp, B., Rescorla, E., Baset, S., and
H. Schulzrinne, "REsource LOcation And Discovery (RELOAD)
Base Protocol", draft-ietf-p2psip-base-26 (work in
progress), February 2013. January 2014.

14.2. Informational Informative References

[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, August 2008.

Authors' Addresses

Ari Keranen
Ericsson
Hirsalantie 11
02420 Jorvas
Finland

Email:

EMail: Ari.Keranen@ericsson.com

Gonzalo Camarillo
Ericsson
Hirsalantie 11
Jorvas 02420
Finland

Email:

EMail: Gonzalo.Camarillo@ericsson.com

Jouni Maenpaa
Ericsson
Hirsalantie 11
Jorvas 02420
Finland

Email:

EMail: Jouni.Maenpaa@ericsson.com