wdiff rfc7576.original rfc7576.txt

Network Management
Internet Research Group Task Force (IRTF) S. Jiang
Internet-Draft
Request for Comments: 7576 Huawei Technologies Co., Ltd
Intended status:
Category: Informational B. Carpenter
Expires: November 2, 2015
ISSN: 2070-1721 Univ. of Auckland
M. Behringer
Cisco Systems
May 1,
June 2015

General Gap Analysis for Autonomic Networking
draft-irtf-nmrg-an-gap-analysis-06

Abstract

This document is a product of the IRTF's Network Management Research
Group. It provides a problem statement and general gap analysis
for an IP-based Autonomic Network that is mainly based on distributed
network devices. The document provides a background by reviewing the
current status of autonomic aspects of IP networks and the extent to
which current network management depends on centralisation centralization and human
administrators. Finally Finally, the document outlines the general features
that are missing from current network abilities that and are needed in the
ideal Autonomic Network concept.

This document is a product of the IRTF's Network Management Research
Group.

Status of This Memo

This Internet-Draft document is submitted in full conformance with not an Internet Standards Track specification; it is
published for informational purposes.

This document is a product of the Internet Research Task Force
(IRTF). The IRTF publishes the
provisions results of BCP 78 Internet-related research
and BCP 79.

Internet-Drafts are working documents development activities. These results might not be suitable for
deployment. This RFC represents the consensus of the Network
Management Research Group of the Internet Engineering Research Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid (IRTF).
Documents approved for publication by the IRSG are not a maximum candidate
for any level of Internet Standard; see Section 2 of six months RFC 5741.

Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on November 2, 2015.
http://www.rfc-editor.org/info/rfc7576.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Automatic and Autonomic Aspects of Current IP Networks . . . 3
3.1. IP Address Management and DNS . . . . . . . . . . . . . . 3
3.2. Routing . . . . . . . . . . . . . . . . . . . . . . . . . 4 5
3.3. Configuration of Default Router in a Host . . . . . . . . 5
3.4. Hostname Lookup . . . . . . . . . . . . . . . . . . . . . 5
3.5. User Authentication and Accounting . . . . . . . . . . . 6
3.6. Security . . . . . . . . . . . . . . . . . . . . . . . . 6
3.7. State Synchronization . . . . . . . . . . . . . . . . . . 7
4. Current Non-Autonomic Non-autonomic Behaviors . . . . . . . . . . . . . . . 7
4.1. Building a New Network . . . . . . . . . . . . . . . . . 7
4.2. Network Maintenance and Management . . . . . . . . . . . 8
4.3. Security Setup . . . . . . . . . . . . . . . . . . . . . 9
4.4. Troubleshooting and Recovery . . . . . . . . . . . . . . 9
5. Features Needed by Autonomic Networks . . . . . . . . . . . . 10
5.1. More Coordination among Devices or Network Partitions . . 11
5.2. Reusable Common Components . . . . . . . . . . . . . . . 11
5.3. Secure Control Plane . . . . . . . . . . . . . . . . . . 12
5.4. Less Configuration . . . . . . . . . . . . . . . . . . . 12
5.5. Forecasting and Dry Runs . . . . . . . . . . . . . . . . 13
5.6. Benefit from Knowledge . . . . . . . . . . . . . . . . . 13
6. Security Considerations . . . . . . . . . . . . . . . . . . . 14
7. IANA Considerations . . Informative References . . . . . . . . . . . . . . . . . . . 14
8.
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 14
9. Change log [RFC Editor: Please remove] . . . . . . . . . . . 14
10. Informative References . . . . . . . . . . . . . . . . . . . 15 17
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 17

1. Introduction

The general goals and relevant definitions for Autonomic Networking
are discussed in [I-D.irtf-nmrg-autonomic-network-definitions]. [RFC7575]. In summary, the fundamental goal of an
Autonomic Network is self-
management, self-management, including self-configuration,
self-optimization, self-
healing self-healing, and self-protection. Whereas
interior gateway routing protocols such as OSPF and IS-IS largely
exhibit these properties, most other aspects of networking require
top-down configuration, often involving human administrators and a
considerable degree of
centralisation. centralization. In essence essence, Autonomic
Networking is putting all network configurations onto the same
footing as routing, limiting manual or database-driven configuration
to an essential minimum. It should be noted that this is highly
unlikely to eliminate the need for human administrators, because many
of their essential tasks will remain. The idea is to eliminate
tedious and error-prone tasks, for
example example, manual calculations,
cross-checking between two different configuration files, or tedious
data entry. Higher level Higher-level operational tasks, and complex trouble-shooting,
troubleshooting, will remain to be done by humans.

This document represents the consensus of the IRTF's network
management research group Network
Management Research Group (NMRG). It first provides background by
identifying examples of partial autonomic behavior in the Internet, Internet
and by describing important areas of non-autonomic behavior. Based
on these observations, it then describes missing general mechanisms
which
that would allow autonomic behaviours behaviors to be added throughout the
Internet.

2. Terminology

The terminology defined in
[I-D.irtf-nmrg-autonomic-network-definitions] [RFC7575] is used in this document.

3. Automatic and Autonomic Aspects of Current IP Networks

This section discusses the history and current status of automatic or
autonomic operations in various aspects of network configuration, in
order to establish a baseline for the gap analysis. In particular,
routing protocols already contain elements of autonomic processes,
such as information exchange and state synchronization.

3.1. IP Address Management and DNS

For many years, there was no alternative to completely manual and
static management of IP addresses and their prefixes. Once a site
had received an IPv4 address assignment (usually a Class C /24 or
Class B /16, and rarely a Class A /8) /8), it was a matter of paper-and-
pencil design of the subnet plan (if relevant) and the addressing
plan itself. Subnet prefixes were manually configured into routers,
and /32 addresses were assigned administratively to individual host
computers,
computers and configured manually by system administrators. Records
were typically kept in a plain text file or a simple spreadsheet.

Clearly

Clearly, this method was clumsy and error-prone as soon as a site had
more than a few tens of hosts, but it had to be used until DHCP
[RFC2131] became a viable solution during the second half of the
1990s. DHCP made it possible to avoid manual configuration of
individual hosts (except, in many deployments, for a small number of
servers configured with static addresses). Even so, prefixes had to
be manually assigned to subnets and their routers, and DHCP servers
had to be configured accordingly.

In terms of management, there is a linkage between IP address
management and DNS management, because DNS mappings typically need to
be appropriately synchronized with IP address assignments. At
roughly the same time as DHCP came into widespread use, it became
very laborious to manually maintain DNS source files in step with IP
address assignments. Because of reverse DNS lookup, it also became
necessary to synthesise synthesize DNS names even for hosts that only played the
role of clients. Therefore, it became necessary to synchronise synchronize DHCP
server tables with forward and reverse DNS. For this reason,
Internet Protocol IP
address management tools emerged, as discussed for the case of
renumbering in [RFC7010]. These are, however,
centralised centralized solutions
that do not exhibit autonomic properties as defined in [I-D.irtf-nmrg-autonomic-network-definitions]. [RFC7575].

A related issue is prefix delegation, especially in IPv6 when more
than one prefix may be delegated to the same physical subnet. DHCPv6
Prefix Delegation [RFC3633] is a useful solution, but it requires
specific configuration so cannot be considered autonomic. How this
topic is to be handled in home networks is still in discussion
[I-D.ietf-homenet-prefix-assignment].
[Pfister]. Still further away is autonomic assignment and delegation
of routeable routable IPv4 subnet prefixes.

An IPv6 network needs several aspects of host address assignments to
be configured. The network might use stateless address
autoconfiguration [RFC4862] or DHCPv6 [RFC3315] in stateless or
stateful modes, and there are various alternative forms of Interface
Identifier [RFC7136].

Another feature is the possibility of Dynamic DNS Update [RFC2136].
With appropriate security, this is an automatic approach, where no
human intervention is required to create the DNS records for a host
after it acquires a new address. However, there are coexistence
issues with a traditional DNS setup, as described in [RFC7010].

3.2. Routing

Since a very early stage, it has been a goal that Internet routing
should be self-healing when there is a failure of some kind in the
routing system (i.e. (i.e., a link or a router goes wrong). Also, the
problem of finding optimal routes through a network was identified
many years ago as a problem in mathematical graph theory, for which
well known algorithms were discovered (the Dijkstra and Bellman-Ford
algorithms). Thus Thus, routing protocols became largely autonomic from
the start, as it was clear that manual configuration of routing
tables for a large network was impractical.

IGP routers do need some initial configuration data to start up the
autonomic routing protocol. Also, BGP-4 routers need detailed static
configuration of routing policy data.

3.3. Configuration of Default Router in a Host

Originally this

Originally, the configuration of a default router in a host was a
manual operation. Since the deployment of DHCP, this has been
automatic as far as most IPv4 hosts are concerned, but the DHCP
server must be appropriately configured. In simple environments such
as a home network, the DHCP server resides in the same box as the
default router, so this configuration is also automatic. In more
complex environments, where an independent DHCP server or a local
DHCP relay is used, DHCP configuration is more complex and not
automatic.

In IPv6 networks, the default router is provided by Router
Advertisement messages [RFC4861] from the router itself, and all IPv6
hosts make use of it. The router may also provide more complex Route
Information Options. The process is essentially autonomic as far as
all IPv6 hosts are concerned, and DHCPv6 is not involved. However,
there are still open issues when more than one prefix is in use on a
subnet
subnet, and more than one first-hop router may be available as a
result (see (see, for example example, [RFC6418]).

3.4. Hostname Lookup

Originally host names

Originally, hostnames were looked up in a static table, often
referred to as "hosts.txt" from its traditional file name. When the
DNS was deployed during the 1980s, all hosts needed DNS resolver
code, code
and needed to be configured with the IP addresses (not the names) of
suitable DNS servers. Like the default router, these were originally
manually configured. Today, they are provided automatically via DHCP
or DHCPv6 [RFC3315]. For IPv6 end systems, there is also a way for
them to be provided automatically via a Router Advertisement option.
However, the DHCP or DHCPv6 server, or the IPv6 router, need needs to be
configured with the appropriate DNS server addresses. Additionally,
some networks deploy Multicast DNS [RFC6762] locally to provide
additional automation of the name space.

3.5. User Authentication and Accounting

Originally, user authentication and accounting was mainly based on
physical connectivity and the degree of trust that follows from
direct connectivity. Network operators charged based on the set up setup of
dedicated physical links with users. Automated user authentication
was introduced by the Point-to-Point Protocol [RFC1661], [RFC1994]
and RADIUS protocol [RFC2865], [RFC2865] [RFC2866] in the early 1990s. As long
as a user completes online authentication through the RADIUS
protocol, the accounting for that user starts on the corresponding AAA
Authentication, Authorization, and Accounting (AAA) server
automatically. This mechanism enables business models with charging
based on the amount of traffic based or time based
usage. time. However, the management of user authentication
information
remains manual continues to be manually managed by network
administrators. It also becomes complex in the case of mobile users
who roam between operators, since prior relationships between the
operators are needed.

3.6. Security

Security has many aspects that need configuration and are therefore
candidates to become autonomic. On the other hand, it is essential
that a network's central policy should be applied strictly for all security
configurations. As a result result, security has largely been based on
centrally imposed configurations.

Many aspects of security depend on policy, for example example, password
rules, privacy rules, firewall rulesets, intrusion detection and
prevention settings, VPN configurations, and the choice of
cryptographic algorithms. Policies are are, by definition definition, human made
and will therefore also persist in an autonomic environment.
However, policies are becoming more high-level, abstracting addressing
addressing, for example, and focusing on the user or application.
The methods to manage, distribute distribute, and apply policy, policy and to monitor
compliance and violations could be autonomic.

Today, many security mechanisms show some autonomic properties. For
example user authentication via IEEE 802.1x allows automatic mapping
of users after authentication into logical contexts (typically
VLANs). While today configuration is still very important, the
overall mechanism displays signs of self-adaption to changing
situations.

BGP Flowspec [RFC5575] allows a partially autonomic threat defense threat-defense
mechanism, where threats are identified, the flow information is
automatically distributed, and counter-actions can be applied. Today
Today, typically a human operator is still in the loop to check
correctness, but over time such mechanisms can become more autonomic.

Negotiation capabilities, present in many security protocols, also
display simple autonomic behaviours. behaviors. In this case case, a security policy
about algorithm strength can be configured into servers but will
propagate automatically to clients.

3.7. State Synchronization

Another area where autonomic processes between peers are involved is
state synchronization. In this case, several devices start out with
inconsistent state and go through a peer-to-peer procedure after
which their states are consistent. Many autonomic or automatic
processes include some degree of implicit state synchronization.
Network time synchronization [RFC5905] is a well-established explicit
example, guaranteeing that a participating node's clock state is
synchronized with reliable time servers within a defined margin of
error, without any overall point of control of the synchronization
process.

4. Current Non-Autonomic Non-autonomic Behaviors

In current networks, many operations are still heavily dependent on
human intelligence and decision, or on centralised centralized top-down network
management systems. These operations are the targets of Autonomic
Networking technologies. The ultimate goal of Autonomic Networking
is to replace human and automated operations by autonomic functions,
so that the networks can run independently without depending on a
human or NMS system Network Management System (NMS) for routine details, while
maintaining central control where required. Of course, there would
still be the absolute minimum of human input required, particularly
during the network
building network-building stage, and during emergencies emergencies, and difficult trouble-
shooting.
troubleshooting.

This section analyzes the existing human and central dependencies in
typical current networks and suggests cases where they could could, in
principle principle,
be replaced by autonomic behaviors.

4.1. Building a New Network

Building a network requires the operator to analyze the requirements
of the new network, design a deployment architecture and topology,
decide device locations and capacities, set up hardware, design
network services, choose and enable required protocols, configure
each device and each protocol, set up central user authentication and
accounting policies and databases, design and deploy security
mechanisms, etc.

Overall, these jobs are quite complex work that cannot become fully
autonomic in the foreseeable future. However, part of these jobs may
be able to become autonomic, such as detailed device and protocol
configurations and database population. The initial network
management policies/behaviors may also be transplanted from other
networks and automatically localized.

4.2. Network Maintenance and Management

Network maintenance and management are very different for ISP
networks and enterprise networks. ISP networks have to change much
more frequently than enterprise networks, given the fact that ISP
networks have to serve a large number of customers who have very
diversified requirements. The current rigid model is that network
administrators design a limited number of services for customers to
order. New requirements of network services may not be able to be
met quickly by human management. Given a real-time request, the
response must be autonomic, in order to be flexible and quickly
deployed. However, behind the interface, describing abstracted
network information and user authorization management may have to
depend on human intelligence from network administrators in the
foreseeable future. User identification integration/consolidation
among networks or network services is another challenge for Autonomic
Network access. Currently, many end users have to manually manage
their user accounts and authentication information when they switch
among networks or network services.

Classical network maintenance and management mainly manages handle the
configuration of network devices. Tools have been developed to
enable remote management and make such management easier. However,
the decision about each configuration detail depends either on human
intelligence or rigid templates. One or the other of Therefore, these is
therefore are the source sources of
all network configuration errors - either -- the human was wrong, or the template
was wrong (or both). wrong, or both were wrong. This is also a barrier to increasing
the utility of network resources, because the human managers cannot
respond quickly enough to network events, such as traffic bursts,
that were not foreseen in the template. For example, currently, a
light load is often assumed in network design because there is no
mechanism to properly handle a sudden traffic flood. It is therefore
common to avoid performance collapses caused by traffic overload by
configuring idle resources, with an overprovisioning ratio of at
least 2 being normal [Xiao02].

There are grounds for concern that the introduction of new, more
flexible, methods of network configuration, typified by software-
defined networking Software-
Defined Networking (SDN), will only make the management problem more
complex unless the details are managed automatically or
autonomically. There is no doubt that SDN creates both the necessity
and the opportunity for automation of configuration management, e.g.,
[Kim13]. This topic is discussed from a service provider viewpoint
in [RFC7149].

Autonomic decision processes for configuration would enable dynamic
management of network resources (by managing resource-relevant
configuration). Self-adapting network configuration would adjust the
network into the best possible situation, which also prevents situation; this would prevent
configuration errors from having lasting impact.

4.3. Security Setup

Setting up security for a network generally requires very detailed
human intervention, intervention or relies entirely on default configurations that
may be too strict or too risky for the particular situation of the
network. While some aspects of security are intrinsically top-down
in nature (e.g. (e.g., broadcasting a specific security policy to all
hosts), others could be self-managed within the network.

In an Autonomic Network, where nodes within a domain have a mutually
verifiable domain identity, security processes could run entirely
automatically. Nodes could identify each other securely, negotiating
required security settings and even shared keys if needed. The
location
locations of the trust anchors (certificate authority, registration
authority), certificate revocation lists, policy server, etc., can be
found by service discovery. Transactions such as a download of a
certificate revocation list download can be authenticated via a common trust
anchor. Policy distribution can also be entirely automated, automated and
secured via a common trust anchor.

These concepts lead to a network where the intrinsic security is
automatic and applied by default, i.e., a "self-protecting" network.
For further discussion, see [I-D.behringer-default-secure] [Behringer].

4.4. Troubleshooting and Recovery

Current networks suffer difficulties in locating the cause of network
failures. Although network devices may issue many warnings while
running, most of them are not sufficiently precise to be identified
as errors. Some of them are early warnings that would not develop
into real errors. Others are are, in effect effect, random noise. During a
major failure, many different devices will issue multiple warnings
within a short time, causing overload for the NMS and the operators.

However, for many scenarios, human experience is still vital to
identify real issues and locate them. This situation may be improved
by automatically associating warnings from multiple network devices
together. Also, introducing automated learning techniques (comparing
current warnings with historical relationships between warnings and
actual faults) could increase the possibility and success rate of
Autonomic Network diagnoses and troubleshooting.

Depending on the network errors, some of them (particularly hardware
failures) may always require human interventions, particularly for hardware failures. intervention. However,
autonomic network Autonomic
Network management behavior may help to reduce the impact of errors,
for example example, by switching traffic flows around. Today Today, this is
usually manual (except for classical routing updates). Fixing
software failures and configuration errors currently depends on
humans,
humans and may even involve rolling back software versions and
rebooting hardware. Such problems could be autonomically corrected
if there were diagnostics and recovery functions defined in advance
for them. This would fulfill the concept of self-healing.

Another possible autonomic function is predicting device failures or
overloads before they occur. A device could predict its own failure
and warn its neighbors; neighbors, or a device could predict its neighbor's
failure. In either case, an Autonomic Network could respond as if
the failure had already occurred by routing around the problem and
reporting the failure, with no disturbance to users. The criteria
for predicting failure could be temperature, battery status, bit
error rates, etc. The criteria for predicting overload could be
increasing load factor, latency, jitter, congestion loss, etc.

5. Features Needed by Autonomic Networks

There are innumerable properties of network devices and end systems
that today need to be configured either manually, by scripting, or by
using a management protocol such as NETCONF the Network Configuration
Protocol (NETCONF) [RFC6241]. In an Autonomic Network, all of these
would need to either have satisfactory default values or be
configured automatically. Some examples are parameters for tunnels
of various kinds, flows (in an SDN context), quality of service,
service function chaining, energy management, system identification identification,
and NTP configuration, but the list is endless.

The task of Autonomic Networking is to incrementally build up
individual autonomic processes that could progressively be combined
to respond to every type of network event. Building on the preceding
background information, and on the reference model in
[I-D.irtf-nmrg-autonomic-network-definitions], [RFC7575], this
section outlines the gaps and missing features in general terms, and terms and,
in some cases cases, mentions general design principles that should apply.

5.1. More Coordination among Devices or Network Partitions

Network services are dependent on a number of devices and parameters
to be in place in a certain order. For example example, after a power failure
failure, a coordinated sequence of "return to normal" operations is
desirable (e.g., switches and routers first, DNS servers second,
etc.). Today, the correct sequence of events is either known only by
a human
administrator, administrator or automated in a central script. In a truly
Autonomic Network, elements should understand their dependencies, dependencies and
be able to resolve them locally.

In order to make right or good decisions autonomically, the network
devices need to know more information than just reachability
(routing) information from the relevant or neighbor devices. There
are dependencies between such information and configurations, which
devices Devices
must be able to derive derive, for themselves. themselves, the dependencies between such
information and configurations.

There are therefore increased requirements for horizontal information
exchange in the networks. Particularly, three types of interaction
among peer network devices are needed for autonomic decisions:
discovery (to find neighbours neighbors and peers), synchronization (to agree on
network status) status), and negotiation (when things need to be changed).
Thus
Thus, there is a need for reusable discovery, synchronization synchronization, and
negotiation mechanisms, which mechanisms that would support the discovery of many
different types of device, the synchronization of many types of
parameter
parameter, and the negotiation of many different types of objective.

5.2. Reusable Common Components

Elements of autonomic functions already exist today, within many
different protocols. However, all such functions have their own
discovery, transport, messaging messaging, and security mechanisms as well as
non-autonomic management interfaces. Each protocol has its own
version of the above-mentioned functions to serve specific and narrow
purposes. It is often difficult to extend an existing protocol to
serve different purposes. Therefore, in order to provide the
reusable discovery, synchronization synchronization, and negotiation mechanism mechanisms
mentioned above, it is desirable to develop a set of reusable common
protocol components for Autonomic Networking. These components
should be:

o Able to identify other devices, users users, and processes securely.

o Able to automatically secure operations, based on the above
identity scheme.

o Able to manage any type of information and information flows.

o Able to discover peer devices and services for various autonomic
service agents Autonomic
Service Agents (or autonomic functions).

o Able to support closed-loop operations when needed to provide
self-managing functions involving more than one device.

o Separable from the specific autonomic service agents Autonomic Service Agents (or autonomic
functions).

o Reusable by other autonomic functions.

5.3. Secure Control Plane

The common components will will, in effect effect, act as a control plane for
autonomic operations. This control plane might be implemented in-
band as functions of the target network, in an overlay network, or
even out-of-band in a separate network. Autonomic operations will be
capable of changing how the network operates and allocating resources
without human intervention or knowledge, so it is essential that they
are secure. Therefore Therefore, the control plane must be designed to be
secure against forged autonomic operations and man-in-the middle
attacks,
attacks and as secure as reasonably possible against denial of denial-of-
service attacks. It must be decided whether the control plane needs
to be resistant to unwanted monitoring, i.e., whether encryption is
required.

5.4. Less Configuration

Many existing protocols have been defined to be as flexible as
possible. Consequently, these protocols need numerous initial
configurations to start operations. There are choices and options
that are irrelevant in any particular case, some of which target
corner cases. Furthermore, in protocols that have existed for years,
some design considerations are no longer relevant, since the
underlying hardware technologies have evolved meanwhile. To
appreciate the scale of this problem, consider that more than 160
DHCP otions options have been defined for IPv4. Even sample router
configuration files readily available on line online contain more than 200
lines of commands. There is therefore considerable scope for
simplifying the operational tools for configuration of common
protocols, even if the underlying protocols themselves cannot be
simplified.

From another perspective, the deep reason why human decisions are
often needed mainly result results from the lack of information. When a
device can collect enough information horizontally from other
devices, it should be able to decide many parameters by itself,
instead of receiving them from top-down configuration.

It is desired that top-down management is reduced in Autonomic
Networking. Ideally, only the abstract Intent is needed from the
human administrators. Neither users nor administrators should need
to create and maintain detailed policies and profiles; if they are
needed, they should be built autonomically. The local parameters
should be decided by distributed Autonomic Nodes themselves, either
from historic knowledge, analytics of current conditions, closed
logical decision loops, or a combination of all.

5.5. Forecasting and Dry Runs

In a conventional network, there is no mechanism for trying something
out safely. That safely, which means that configuration changes have to be
designed in the abstract and their probable effects have to be
estimated theoretically. In principle, an alternative to this would
be to test the changes on a complete and realistic network simulator.
However, this is a practical impossibility for a large network which that
is constantly changing, even if an accurate simulation could be
performed. There is therefore a risk that applying changes to a
running network will cause a failure of some kind. An autonomic
network could fill this gap by supporting a closed loop "dry run"
mode in which each configuration change could be tested out
dynamically in the control plane without actually affecting the data
plane. If the results are satisfactory, the change could be made
live on the running network. If there is a consistency problem such
as over-commitment overcommitment of resources or incompatibility with another
configuration setting, the change could be rolled back dynamically
with no impact on traffic or users.

5.6. Benefit from Knowledge

The more knowledge and experience we have, the better decisions we
can take. make. It is the same for networks and network management. When
one component in the network lacks knowledge that affects what it
should do, and another component has that knowledge, we usually rely
on a human operator or a centralised centralized management tool to convey the
knowledge.

Up to now, the only available network knowledge is usually the
current network status inside a given device or relevant current
status from other devices.

However, historic knowledge is very helpful to make correct
decisions, in particular particular, to reduce network oscillation or to manage
network resources over time. Transplantable knowledge from other
networks can be helpful to initially set up a new network or new
network devices. Knowledge of relationships between network events
and network configuration may help a network to decide the best
parameters according to real performance feedback.

In addition to such historic knowledge, powerful data analytics of
current network conditions may also be a valuable source of knowledge
that can be exploited directly by Autonomic Nodes.

6. Security Considerations

This document is focused on what is missing to allow autonomic
network configuration, including of course security settings. settings, of course.
Therefore, it does not itself create any new security issues. It is
worth underlining that autonomic technology must be designed with
strong security properties from the start, since a network with
vulnerable autonomic functions would be at great risk.

7. IANA Considerations

This memo includes no request to IANA.

8. Acknowledgements

The authors would like to acknowledge the valuable comments made by
participants in the IRTF Network Management Research Group. Reviews
by Kevin Fall and Rene Struik were especially helpful.

This document was produced using the xml2rfc tool [RFC2629].

9. Change log [RFC Editor: Please remove]

draft-irtf-nmrg-an-gap-analysis-06: RFC Editor comments actioned,
2015-05-01.

draft-irtf-nmrg-an-gap-analysis-05: IESG Review comments actioned,
2015-03-23.

draft-irtf-nmrg-an-gap-analysis-04: Additional IRSG Review comments
actioned, 2015-03-04.

draft-irtf-nmrg-an-gap-analysis-03: IRSG Review comments actioned,
2014-12-11.

draft-irtf-nmrg-an-gap-analysis-02: Review comments actioned,
2014-10-02.

draft-irtf-nmrg-an-gap-analysis-01: RG comments added and more
content in "Approach toward Autonomy" section, 2014-08-30.

draft-irtf-nmrg-an-gap-analysis-00: RG comments added, 2014-04-02.

draft-jiang-nmrg-an-gap-analysis-00: original version, 2014-02-14.

10. Informative References

[I-D.behringer-default-secure]

[Behringer]
Behringer, M., Pritikin, M., and S. Bjarnason, "Making The
Internet Secure By Default", draft-behringer-default-
secure-00 (work Work in progress), Progress,
draft-behringer-default-secure-00, January 2014.

[I-D.ietf-homenet-prefix-assignment]
Pfister, P., Paterson, B., and J. Arkko, "Distributed
Prefix Assignment Algorithm", draft-ietf-homenet-prefix-
assignment-05 (work in progress), April 2015.

[I-D.irtf-nmrg-autonomic-network-definitions]
Behringer, M., Pritikin, M., Bjarnason, S., Clemm, A.,
Carpenter, B., Jiang, S., and L. Ciavaglia, "Autonomic
Networking - Definitions and Design Goals", draft-irtf-
nmrg-autonomic-network-definitions-07 (work in progress),
March 2015.

[Kim13] Kim, H. and N. Feamster, "Improving Network Management
with Software Defined Networking", IEEE Communications
Magazine, Pages pages 114-119, February 2013.

[Pfister] Pfister, P., Paterson, B., and J. Arkko, "Distributed
Prefix Assignment Algorithm", Work in Progress,
draft-ietf-homenet-prefix-assignment-07, June 2015.

[RFC1661] Simpson, W., Ed., "The Point-to-Point Protocol (PPP)",
STD 51, RFC 1661, DOI 10.17487/RFC1661, July 1994. 1994,
<http://www.rfc-editor.org/info/rfc1661>.

[RFC1994] Simpson, W., "PPP Challenge Handshake Authentication
Protocol (CHAP)", RFC 1994, DOI 10.17487/RFC1994, August 1996.
1996, <http://www.rfc-editor.org/info/rfc1994>.

[RFC2131] Droms, R., "Dynamic Host Configuration Protocol",
RFC 2131, DOI 10.17487/RFC2131, March 1997. 1997,
<http://www.rfc-editor.org/info/rfc2131>.

[RFC2136] Vixie, P., Ed., Thomson, S., Rekhter, Y., and J. Bound,
"Dynamic Updates in the Domain Name System (DNS UPDATE)",
RFC 2136, DOI 10.17487/RFC2136, April 1997.

[RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629,
June 1999. 1997,
<http://www.rfc-editor.org/info/rfc2136>.

[RFC2865] Rigney, C., Willens, S., Rubens, A., and W. Simpson,
"Remote Authentication Dial In User Service (RADIUS)",
RFC 2865, DOI 10.17487/RFC2865, June 2000. 2000,
<http://www.rfc-editor.org/info/rfc2865>.

[RFC2866] Rigney, C., "RADIUS Accounting", RFC 2866,
DOI 10.17487/RFC2866, June 2000. 2000,
<http://www.rfc-editor.org/info/rfc2866>.

[RFC3315] Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins,
C., and M. Carney, "Dynamic Host Configuration Protocol
for IPv6 (DHCPv6)", RFC 3315, DOI 10.17487/RFC3315, July 2003.
2003, <http://www.rfc-editor.org/info/rfc3315>.

[RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic
Host Configuration Protocol (DHCP) version 6", RFC 3633,
DOI 10.17487/RFC3633, December 2003. 2003,
<http://www.rfc-editor.org/info/rfc3633>.

[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
DOI 10.17487/RFC4861, September 2007. 2007,
<http://www.rfc-editor.org/info/rfc4861>.

[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862,
DOI 10.17487/RFC4862, September 2007. 2007,
<http://www.rfc-editor.org/info/rfc4862>.

[RFC5575] Marques, P., Sheth, N., Raszuk, R., Greene, B., Mauch, J.,
and D. McPherson, "Dissemination of Flow Specification
Rules", RFC 5575, DOI 10.17487/RFC5575, August 2009. 2009,
<http://www.rfc-editor.org/info/rfc5575>.

[RFC5905] Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch,
"Network Time Protocol Version 4: Protocol and Algorithms
Specification", RFC 5905, DOI 10.17487/RFC5905, June 2010. 2010,
<http://www.rfc-editor.org/info/rfc5905>.

[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011. 2011,
<http://www.rfc-editor.org/info/rfc6241>.

[RFC6418] Blanchet, M. and P. Seite, "Multiple Interfaces and
Provisioning Domains Problem Statement", RFC 6418,
DOI 10.17487/RFC6418, November 2011. 2011,
<http://www.rfc-editor.org/info/rfc6418>.

[RFC6762] Cheshire, S. and M. Krochmal, "Multicast DNS", RFC 6762,
DOI 10.17487/RFC6762, February 2013. 2013,
<http://www.rfc-editor.org/info/rfc6762>.

[RFC7010] Liu, B., Jiang, S., Carpenter, B., Venaas, S., and W.
George, "IPv6 Site Renumbering Gap Analysis", RFC 7010,
DOI 10.17487/RFC7010, September 2013. 2013,
<http://www.rfc-editor.org/info/rfc7010>.

[RFC7136] Carpenter, B. and S. Jiang, "Significance of IPv6
Interface Identifiers", RFC 7136, DOI 10.17487/RFC7136,
February 2014. 2014, <http://www.rfc-editor.org/info/rfc7136>.

[RFC7149] Boucadair, M. and C. Jacquenet, "Software-Defined
Networking: A Perspective from within a Service Provider
Environment", RFC 7149, DOI 10.17487/RFC7149, March 2014. 2014,
<http://www.rfc-editor.org/info/rfc7149>.

[RFC7575] Behringer, M., Pritikin, M., Bjarnason, S., Clemm, A.,
Carpenter, B., Jiang, S., and L. Ciavaglia, "Autonomic
Networking: Definitions and Design Goals", RFC 7575,
DOI 10.17487/RFC7575, June 2015,
<http://www.rfc-editor.org/info/rfc7575>.

[Xiao02] Xiao, X. X., Telkamp, T., Fineberg, V., Chen, C., and others, L. Ni,
"A Practical Approach for Providing QoS in the Internet
Backbone", IEEE Communications Magazine, Pages 56-59, pages 56-62,
December 2002.

Acknowledgements

The authors would like to acknowledge the valuable comments made by
participants in the IRTF Network Management Research Group. Reviews
by Kevin Fall and Rene Struik were especially helpful.

Authors' Addresses

Sheng Jiang
Huawei Technologies Co., Ltd
Q14, Huawei Campus, No.156 Beiqing Road
Hai-Dian District, Beijing, 100095
P.R.
China

Email:

EMail: jiangsheng@huawei.com

Brian Carpenter
Department of Computer Science
University of Auckland
PB 92019
Auckland 1142
New Zealand

Email:

EMail: brian.e.carpenter@gmail.com

Michael H. Behringer
Cisco Systems
Building D, 45 Allee des Ormes
Mougins 06250
France

Email:

EMail: mbehring@cisco.com