wdiff rfc7604.original rfc7604.txt

Network Working Group
Internet Engineering Task Force (IETF) M. Westerlund
Internet-Draft
Request for Comments: 7604 Ericsson
Intended status:
Category: Informational T. Zeng
Expires: November 20, 2015 May 19,
ISSN: 2070-1721 PacketVideo Corp
August 2015

The

Comparison of Different Network Address Translator (NAT) NAT Traversal Techniques
for Media Controlled by Real-time the Real-Time Streaming Protocol (RTSP)
draft-ietf-mmusic-rtsp-nat-evaluation-16

Abstract

This document describes several Network Address Translator (NAT)
traversal techniques that were considered to be used for establishing
the RTP media flows controlled by the Real-time Real-Time Streaming Protocol
(RTSP). Each technique includes a description of how it would be
used, the security implications of using it it, and any other deployment
considerations it has. There are also discussions on how NAT
traversal techniques relate to firewalls and how each technique can
be applied in different use cases. These findings were used when
selecting the NAT traversal for RTSP 2.0, which is specified in a
separate document.

Status of This Memo

This Internet-Draft document is submitted in full conformance with the
provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents not an Internet Standards Track specification; it is
published for informational purposes.

This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a maximum candidate for any level of Internet
Standard; see Section 2 of six months RFC 5741.

Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on November 20, 2015.
http://www.rfc-editor.org/info/rfc7604.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Network Address Translators . . . . . . . . . . . . . . . 5
1.2. Firewalls . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3. Glossary . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Detecting the loss Loss of NAT mappings Mappings . . . . . . . . . . . . . 7
3. Requirements on Solutions . . . . . . . . . . . . . . . . . . 8
4. NAT Traversal NAT-Traversal Techniques . . . . . . . . . . . . . . . . . . 10
4.1. Stand-Alone STUN . . . . . . . . . . . . . . . . . . . . 10
4.1.1. Introduction . . . . . . . . . . . . . . . . . . . . 10
4.1.2. Using STUN to traverse Traverse NAT without server
modifications Server
Modifications . . . . . . . . . . . . . . . . . . . . 11
4.1.3. ALG considerations Considerations . . . . . . . . . . . . . . . . . 13
4.1.4. Deployment Considerations . . . . . . . . . . . . . . 14
4.1.5. Security Considerations . . . . . . . . . . . . . . . 15
4.2. Server Embedded STUN . . . . . . . . . . . . . . . . . . 15
4.2.1. Introduction . . . . . . . . . . . . . . . . . . . . 15
4.2.2. Embedding STUN in RTSP . . . . . . . . . . . . . . . 15
4.2.3. Discussion On on Co-located STUN Server . . . . . . . . 17
4.2.4. ALG considerations Considerations . . . . . . . . . . . . . . . . . 17
4.2.5. Deployment Considerations . . . . . . . . . . . . . . 17
4.2.6. Security Considerations . . . . . . . . . . . . . . . 18
4.3. ICE . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.3.1. Introduction . . . . . . . . . . . . . . . . . . . . 18
4.3.2. Using ICE in RTSP . . . . . . . . . . . . . . . . . . 19
4.3.3. Implementation burden Burden of ICE . . . . . . . . . . . . 21
4.3.4. ALG Considerations . . . . . . . . . . . . . . . . . 21
4.3.5. Deployment Considerations . . . . . . . . . . . . . . 22
4.3.6. Security Consideration Considerations . . . . . . . . . . . . . . . 22
4.4. Latching . . . . . . . . . . . . . . . . . . . . . . . . 23
4.4.1. Introduction . . . . . . . . . . . . . . . . . . . . 23
4.4.2. Necessary RTSP extensions Extensions . . . . . . . . . . . . . . 23
4.4.3. ALG Considerations . . . . . . . . . . . . . . . . . 24
4.4.4. Deployment Considerations . . . . . . . . . . . . . . 24
4.4.5. Security Consideration Considerations . . . . . . . . . . . . . . . 25
4.5. A Variation to Latching . . . . . . . . . . . . . . . . . 26 27
4.5.1. Introduction . . . . . . . . . . . . . . . . . . . . 27
4.5.2. Necessary RTSP extensions Extensions . . . . . . . . . . . . . . 27
4.5.3. ALG Considerations . . . . . . . . . . . . . . . . . 28
4.5.4. Deployment Considerations . . . . . . . . . . . . . . 28
4.5.5. Security Considerations . . . . . . . . . . . . . . . 28
4.6. Three Way Three-Way Latching . . . . . . . . . . . . . . . . . . . 28 29
4.6.1. Introduction . . . . . . . . . . . . . . . . . . . . 28 29
4.6.2. Necessary RTSP extensions Extensions . . . . . . . . . . . . . . 29
4.6.3. ALG Considerations . . . . . . . . . . . . . . . . . 29
4.6.4. Deployment Considerations . . . . . . . . . . . . . . 29
4.6.5. Security Considerations . . . . . . . . . . . . . . . 29 30
4.7. Application Level Gateways . . . . . . . . . . . . . . . 30
4.7.1. Introduction . . . . . . . . . . . . . . . . . . . . 30
4.7.2. Outline On how on How ALGs for RTSP work Work . . . . . . . . . . 31
4.7.3. Deployment Considerations . . . . . . . . . . . . . . 32
4.7.4. Security Considerations . . . . . . . . . . . . . . . 32
4.8. TCP Tunneling . . . . . . . . . . . . . . . . . . . . . . 33
4.8.1. Introduction . . . . . . . . . . . . . . . . . . . . 33
4.8.2. Usage of TCP tunneling Tunneling in RTSP . . . . . . . . . . . 33
4.8.3. ALG Considerations . . . . . . . . . . . . . . . . . 33
4.8.4. Deployment Considerations . . . . . . . . . . . . . . 34
4.8.5. Security Considerations . . . . . . . . . . . . . . . 34
4.9. TURN (Traversal Traversal Using Relay NAT) . . . . Relays around NAT (TURN) . . . . . . . . 34 35
4.9.1. Introduction . . . . . . . . . . . . . . . . . . . . 34 35
4.9.2. Usage of TURN with RTSP . . . . . . . . . . . . . . . 35
4.9.3. ALG Considerations . . . . . . . . . . . . . . . . . 36
4.9.4. Deployment Considerations . . . . . . . . . . . . . . 36
4.9.5. Security Considerations . . . . . . . . . . . . . . . 37
5. Firewalls . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6. Comparison of NAT traversal techniques Traversal Techniques . . . . . . . . . . . 38
7. IANA Security Considerations . . . . . . . . . . . . . . . . . . . . . 40
8. Security Considerations Informative References . . . . . . . . . . . . . . . . . . . 40
9. 41
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 41
10. Informative References . . . . . . . . . . . . . . . . . . . 42 44
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 44 45

1. Introduction

Today there is a proliferating deployment of different types of
Network Address Translator (NAT) boxes that in many cases only
loosely follow standards
[RFC3022][RFC2663][RFC3424][RFC4787][RFC5382]. [RFC3022] [RFC2663] [RFC3424] [RFC4787]
[RFC5382]. NATs cause discontinuity in address realms [RFC3424], therefore [RFC3424];
therefore, an application protocol, such as Real-time the Real-Time Streaming
Protocol (RTSP)
[RFC2326][I-D.ietf-mmusic-rfc2326bis], [RFC2326] [RTSP], needs to deal with such
discontinuities caused by NATs. The problem is that, being a media
control protocol managing one or more media streams, RTSP carries
network address and port information within its protocol messages.
Because of this, even if RTSP itself, when carried over the
Transmission Control Protocol (TCP) [RFC0793] [RFC0793], for example, is not
blocked by NATs, its media streams may be blocked by NATs. This will
occur unless special protocol provisions are added to support NAT-traversal. NAT
traversal.

Like NATs, firewalls are also middle boxes middleboxes that need to be considered.
Firewalls help prevent unwanted traffic from getting in or out of the
protected network. RTSP is designed such that a firewall can be
configured to let RTSP controlled RTSP-controlled media streams go through with
limited implementation effort. The effort needed is to implement an
Application Level Gateway (ALG) to interpret RTSP parameters. There
is also a large class of firewalls, commonly home firewalls, that uses use
a filtering behavior that appear appears to be the same to as what NATs have.
This type of firewall will be successfully traversed using the same
solution as employed for NAT traversal, instead of relying on a an RTSP
ALG. Therefore Therefore, firewalls will also be discussed and some important
differences highlighted.

This document describes several NAT-traversal NAT traversal mechanisms for RTSP RTSP-
controlled media streaming. Many of these NAT solutions fall into
the category of "UNilateral Self-Address Fixing (UNSAF)" as defined
in [RFC3424] and quoted below:

"UNSAF

[UNSAF] is a process whereby some originating process attempts to
determine or fix the address (and port) by which it is known -
e.g. to be able to use address data in the protocol exchange, or
to advertise a public address from which it will receive connections."
connections.

Following the guidelines spelled out in RFC 3424, we describe the
required RTSP protocol extensions for each method, transition strategies, and
security concerns. The transition strategies are a discussion of how
and if the method encourage encourages a move towards not having any NATs on
the path.

This document is capturing the evaluation done in the process to
recommend firewall/NAT traversal methods for RTSP streaming servers
based on RFC 2326 [RFC2326] as well as the RTSP 2.0 core spec
[I-D.ietf-mmusic-rfc2326bis]. specification [RTSP].
The evaluation is focused on NAT traversal for the media streams
carried over the User Datagram Protocol (UDP) [RFC0768] with Real-time Transport Protocol (RTP) RTP
[RFC3550] over UDP being the main case for such usage. The findings
should be applicable to other protocols as long as they have similar
properties.

At the time when the bulk of work on this document was done, a single
level of NAT was the dominant deployment for NATs, and multiple level
levels of NATs, including Carrier Grade Carrier-Grade NATs (CGNs) was (CGNs), were not
considered. Thus, any characterizations or findings may not be
applicable in such scenarios, unless CGN or multiple level levels of NATs
are explicitly noted.

An ICE-based RTSP NAT traversal mechanism based on Interactive Connectivity
Establishment (ICE) is specified in "A Network Address Translator
(NAT) Traversal mechanism Mechanism for media controlled Media Controlled by Real-Time Streaming
Protocol (RTSP)" [I-D.ietf-mmusic-rtsp-nat]. [RTSP-NAT].

1.1. Network Address Translators

We begin by reviewing two quotes from Section 3 in "Network Address
Translation (NAT) Behavioral Requirements for Unicast UDP" [RFC4787]
concerning NATs and their terminology:

"Readers

Readers are urged to refer to [RFC2663] for information on NAT
taxonomy and terminology. Traditional NAT is the most common type
of NAT device deployed. Readers may refer to [RFC3022] for
detailed information on traditional NAT. Traditional NAT has two
main varieties -- Basic NAT and Network Address/Port Translator
(NAPT).

NAPT is by far the most commonly deployed NAT device. NAPT allows
multiple internal hosts to share a single public IP address
simultaneously. When an internal host opens an outgoing TCP or
UDP session through a NAPT, the NAPT assigns the session a public
IP address and port number, so that subsequent response packets
from the external endpoint can be received by the NAPT,
translated, and forwarded to the internal host. The effect is
that the NAPT establishes a NAT session to translate the (private
IP address, private port number) tuple to a (public IP address,
public port number) tuple, and vice versa, for the duration of the
session. An issue of relevance to peer-to-peer applications is
how the NAT behaves when an internal host initiates multiple
simultaneous sessions from a single (private IP, private port)
endpoint to multiple distinct endpoints on the external network.
In this specification, the term "NAT" refers to both "Basic NAT"
and "Network Address/Port Translator (NAPT)"."

"This (NAPT)".

This document uses the term "address "Address and port mapping" Port Mapping" as the
translation between an external address and port and an internal
address and port. Note that this is not the same as an "address
binding" as defined in RFC 2663." 2663.

Note: In the above text, it would be more correct to use an
external IP address instead of a public IP address in the above text. address. The external
IP address is commonly a public one, but it might be of
other another
type if the NAT's external side is in a private address domain.

In addition to the above quote quote, there exists a number of address and
port mapping behaviors described in more detail in Section 4.1 of
"Network Address Translation (NAT) Behavioral Requirements for
Unicast UDP"
[RFC4787] that are highly relevant to the discussion in this
document.

NATs also have a filtering behavior on traffic arriving on the
external side. Such behavior affects how well different methods for
NAT traversal works through these NATs. See Section 5 of "Network
Address Translation (NAT) Behavioral Requirements for Unicast UDP" [RFC4787]
for more information on the different types of filtering that have
been identified.

1.2. Firewalls

A firewall is a security gateway that enforces certain access control
policies between two network administrative domains: a private domain
(intranet) and a an external domain, e.g. e.g., the Internet. Many
organizations use firewalls to prevent intrusions and an malicious
attacks on computing resources in the private intranet [RFC2588].

A comparison between NAT and a firewall is given below:

1. A firewall sits at security enforcement/protection points, while
NAT sits at borders between two address domains.

2. NAT does not in itself provide security, although some access
control policies can be implemented using address translation
schemes. The inherent filtering behaviours behaviors are commonly mistaken
for real security policies.

It should be noted that many NAT devices intended for Residential or
small office/home office
Small Office, Home Office (SOHO) use include both NATs and firewall
functionality.

1.3. Glossary

Address-Dependent Mapping: The NAT reuses the port mapping for
subsequent packets sent from the same internal IP address and
port to the same external IP address, regardless of the
external port. See port; see [RFC4787].

Address and Port-Dependent Mapping: The NAT reuses the port mapping
for subsequent packets sent from the same internal IP address
and port to the same external IP address and port while the
mapping is still active. See active; see [RFC4787].

ALG: Application Level Gateway, Gateway is an entity that can be embedded in
a NAT or other middlebox to perform the application layer
functions required for a particular protocol to traverse the
NAT/middlebox.

Endpoint-Independent Mapping: The NAT reuses the port mapping for
subsequent packets sent from the same internal IP address and
port to any external IP address and port. See port; see [RFC4787].

ICE: Interactive Connectivity Establishment, Establishment; see [RFC5245].

DNS: Domain Name Service

DoS: Denial of Service

DDoS: Distributed Denial of Service

NAT: Network Address Translator, Translator; see [RFC3022].

NAPT: Network Address/Port Translator, Translator; see [RFC3022].

RTP: Real-time Real-Time Transport Protocol, Protocol; see [RFC3550].

RTSP: Real-Time Streaming Protocol, Protocol; see [RFC2326] and
[I-D.ietf-mmusic-rfc2326bis]. [RTSP].

RTT: Round Trip Times. Times

SDP: Session Description Protocol, Protocol; see [RFC4566].

SSRC: Synchronization source in RTP, RTP; see [RFC3550].

2. Detecting the loss Loss of NAT mappings Mappings

Several NAT traversal techniques in the next chapter make use of the
fact that the NAT UDP mapping's external address and port can be
discovered. This information is then utilized to traverse the NAT
box. However However, any such information is only good while the mapping is
still valid. As the IAB's UNSAF document [RFC3424] points out, the
mapping can either timeout or change its properties. It is therefore
important for the NAT traversal solutions to handle the loss or
change of NAT mappings, according to RFC3424. RFC 3424.

First, since NATs may also dynamically reclaim or readjust address/
port translations, "keep-alive" and periodic re-polling repolling may be
required according to RFC 3424. Secondly, Second, it is possible to detect and
recover from the situation where the mapping has been changed or
removed. The loss of a mapping can be detected when no traffic
arrives for a while. Below we will give some recommendation recommendations on how
to detect the loss of NAT mappings when using RTP/RTCP under RTSP
control.

An RTP session normally has both RTP and RTCP streams. The loss of a
an RTP mapping can only be detected when expected traffic does not
arrive. If a client does not receive media data within a few seconds
after having received the "200 OK" response to a an RTSP PLAY request
which
that starts the media delivery, it may be the result of a middlebox
blocking the traffic. However, for a receiver to be more certain to
detect the case where no RTP traffic was delivered due to NAT
trouble, one should monitor the RTCP Sender reports if they are
received and not also blocked. The sender report carries a field
telling how many packets the server has sent. If that has increased
and no RTP packets has have arrived for a few seconds seconds, it is likely the
mapping for the RTP stream has been removed.

The loss of mapping for RTCP is simpler to detect. RTCP is normally
sent periodically in each direction, even during the RTSP ready
state. If RTCP packets are missing for several RTCP intervals, the
mapping is likely lost. Note that if neither RTCP packets nor RTSP
messages are received by the RTSP server for a while (default 60
seconds), the RTSP server has the option to delete the corresponding
RTP session, SSRC and RTSP session ID, because either the client can
not get through a middle box middlebox NAT/firewall, or the client is mal-
functioning.
malfunctioning.

3. Requirements on Solutions

This section considers the set of requirements for the evaluation of
RTSP NAT traversal solutions.

RTSP is a client-server protocol. Typically Typically, service providers
deploy RTSP servers on the public Internet or otherwise other reachable address
realm. However, there are use cases where the reverse is true: RTSP
clients are connecting from any address realm to RTSP servers behind
NATs,
e.g. e.g., in a home. This is the case case, for instance instance, when home
surveillance cameras running as RTSP servers intend to stream video
to cell phone users in the public address realm through a home NAT.
In terms of requirements, the primary issue to solve is the RTSP NAT
traversal problem for RTSP servers deployed in a network where the
server is on the external side of any NAT, i.e. i.e., the server is not
behind a NAT. The server behind a NAT is desirable, desirable but of much lower
priority.

An important consideration

Important considerations for any NAT traversal technique is are whether
any protocol modification needs occur, modifications are needed and where the implementation
burden occur, resides (e.g., server, client client, or middlebox. middlebox). If the incitement
incentive to get RTSP to work over a NAT is sufficient to sufficient, it will
motivate the owner of the server, client client, or middlebox to update or configure update,
configure, or otherwise perform changes to the device and its
software in order to support the NAT traversal. Thus, the question questions of
who this burden falls on and how big it is is are highly relevant.

The list of feature requirements for RTSP NAT solutions are given
below:

1. Must work for all flavors of NATs, including NATs with Address
and Port-Dependent Filtering.

2. Must work for firewalls (subject to pertinent firewall
administrative policies), including those with ALGs.

3. Should have minimal impact on clients not behind NATs and which that
are not dual-hosted. dual hosted. RTSP dual-hosting dual hosting means that the RTSP
signalling
signaling protocol and the media protocol (e.g. (e.g., RTP) are
implemented on different computers with different IP addresses.

* For instance, no extra protocol RTT before arrival of media.

4. Should be simple to use/implement/administer so people actually
turn them on on.

* Discovery of the address(es) assigned by NAT should happen
automatically, if possible possible.

5. Should authenticate dual-hosted client's media transport receiver
to prevent usage of RTSP servers for DDoS attacks.

The last requirement addresses the Distributed Denial-of-Service
(DDoS) threat, which relates to NAT traversal as explained below.

During NAT traversal, when the RTSP server determines the media
destination (address and port) for the client, the result may be that
the IP address of the RTP receiver host is different than the IP
address of the RTSP client host. This posts poses a DDoS threat that has
significant amplification potentials because the RTP media streams in
general consist of a large number of IP packets. DDoS attacks can occur
if the attacker can fake the messages in the NAT traversal mechanism
to trick the RTSP server into believing that the client's RTP
receiver is located on a host to be attacked. For example, user A
may use his RTSP client to direct the RTSP server to send video RTP
streams to target.example.com in order to degrade the services
provided by target.example.com.

Note that a simple mitigation is for the RTSP server to disallow the
cases where the client's RTP receiver has a different IP address than
that of the RTSP client. This is recommended behavior in RTSP 2.0
unless other solutions to prevent this attack is present, See are present; see
Section 21.2.1 in
[I-D.ietf-mmusic-rfc2326bis]. [RTSP]. With the increased deployment of NAT
middleboxes by operators, i.e. carrier grade NAT (CGN), i.e., CGN, the reuse of an IP address on
the NAT's external side by many customers reduces the protection
provided. Also in some applications (e.g., centralized
conferencing), dual-hosted RTSP/RTP clients have valid use cases.

The key is how to authenticate the messages exchanged during the NAT
traversal process.

4. NAT Traversal NAT-Traversal Techniques

There exists a number of potential NAT traversal techniques that can
be used to allow RTSP to traverse NATs. They have different features
and are applicable to different topologies; their costs are also
different. They also vary in security levels. In the following
sections, each technique is outlined with discussions on the
corresponding advantages and disadvantages.

The survey of traversal techniques was done prior to 2007 and is
based on what was available then. This section includes NAT
traversal techniques that have not been formally specified anywhere
else. This document may be the only publicly available specification
of some of the NAT traversal techniques. However However, that is not a real
barrier against doing an evaluation of the NAT traversal techniques.
Some techniques used as part of some of the traversal solutions have
been recommended against or are no longer possible due to
standardization works' the outcome
of standardization work or their failure to progress within IETF
after the initial evaluation in this document. For example example, RTP
No-Op [I-D.ietf-avt-rtp-no-op] [RTP-NO-OP] was a proposed RTP payload format that failed to be specified, thus IETF
approval; thus, it is not available for use today. In each such
case, the missing parts will be noted and some basic reasons will be
given.

4.1. Stand-Alone STUN

4.1.1. Introduction

Session Traversal Utilities for NAT (STUN) [RFC5389] is a
standardized protocol that allows a client to use secure means to
discover the presence of a NAT between itself and the STUN server.
The client uses the STUN server to discover the address and port
mappings assigned by the NAT. Then using the knowledge of these NAT mappings
use
mappings, it uses the external addresses to directly connect to the
independent RTSP server. However, this is only possible if the NAT
address and port mapping behavior is such that the STUN server and
RTSP server will see the same external address and port for the same
internal address and port.

STUN is a client-server protocol. The STUN client sends a request to
a STUN server and the server returns a response. There are two types
of STUN messages - -- Binding Requests and Indications. Binding
requests
Requests are used when determining a client's external address and
solicits
soliciting a response from the STUN server with the seen address.

Indications are used by the client for keep-alive messages towards
the server and requires no response from the server.

The first version of STUN [RFC3489] included categorization and
parameterization of NATs. This was abandoned in the updated version
[RFC5389] due to it being unreliable and brittle. This particular
traversal method uses the removed RFC3489 functionality described in RFC 3489
to detect the NAT type to give an early failure indication when the
NAT is showing the behavior that this method can't support. This
method also
suggest suggests using the RTP NO-OP No-Op payload format [I-D.ietf-avt-rtp-no-op] [RTP-NO-OP]
for key-alives keep-alives of the RTP traffic in the client to server client-to-server direction.
This can be replaced with another form of UDP packet as will be
further discussed below.

4.1.2. Using STUN to traverse Traverse NAT without server modifications Server Modifications

This section describes how a client can use STUN to traverse NATs to
RTSP servers without requiring server modifications. Note that this
method has limited applicability and requires the server to be
available in the external/public address realm in regards to the
client located behind a NAT(s).

Limitations:

o The server must be located in either a public address realm or the
next hop
next-hop external address realm in regards to the client.

o The client may only be located behind NATs that perform "Endpoint-
Independent" Endpoint-
Independent or "Address-Dependent" Address-Dependent Mappings (STUN (the STUN server and
RTSP server on the same IP address). Clients behind NATs that do "Address
Address and Port-Dependent" Port-Dependent Mappings cannot use this method. See
[RFC4787] for the full definition of these terms.

o Based on the discontinued middlebox classification of the replaced
STUN specification [RFC3489]. Thus [RFC3489]; thus, it is brittle and unreliable.

Method:

An RTSP client using RTP transport over UDP can use STUN to traverse
a NAT(s) in the following way:

1. Use STUN to try to discover the type of NAT, NAT and the timeout
period for any UDP mapping on the NAT. This is recommended to be
performed in the background as soon as IP connectivity is
established. If this is performed prior to establishing a
streaming session session, the delays in the session establishment will
be reduced. If no NAT is detected, normal SETUP should be used.

2. The RTSP client determines the number of UDP ports needed by
counting the number of needed media transport protocols sessions
in the multi-media multimedia presentation. This information is available in
the media description protocol, e.g. e.g., SDP [RFC4566]. For
example, each RTP session will in general require two UDP ports, ports:
one for RTP, and one for RTCP.

3. For each UDP port required, establish a mapping and discover the
public/external IP address and port number with the help of the
STUN server. A successful mapping looks like: client's local
address/port <-> public address/port.

4. Perform the RTSP SETUP for each media. In the transport header Transport header,
the following parameter should be included with the given values:
"dest_addr" [I-D.ietf-mmusic-rfc2326bis] [RTSP] or "destination" + "client_port" [RFC2326]
with the public/external IP address and port pair for both RTP
and RTCP. To be certain that this works works, servers must allow a
client to setup set up the RTP stream on any port, not only even ports
and with non-contiguous port numbers for RTP and RTCP. This
requires the new feature provided in RTSP 2.0
[I-D.ietf-mmusic-rfc2326bis]. [RTSP]. The server
should respond with a
transport Transport header containing an "src_addr"
or "source" + "server_port" parameters with the RTP and RTCP
source IP address and port of the media stream.

5. To keep the mappings alive, the client should periodically send
UDP traffic over all mappings needed for the session. For the
mapping carrying RTCP traffic traffic, the periodic RTCP traffic are is
likely enough. For mappings carrying RTP traffic and for
mappings carrying RTCP packets at too low of a frequency, keep-alive keep-
alive messages should be sent.

If a UDP mapping is lost, the above discovery process must be
repeated. The media stream also needs to be SETUP again to change
the transport parameters to the new ones. This will cause a glitch
in media playback.

To allow UDP packets to arrive from the server to a client behind a
"Address Dependent" an
Address-Dependent or "Address Address and Port Dependent" filtering Port-Dependent Filtering NAT, the
client must first send a UDP packet to establish the filtering state
in the NAT. The client, before sending a an RTSP PLAY request, must
send a so called so-called hole-punching packet on each mapping, mapping to the IP
address and port given as the server's source address and port. For
a NAT that only is "Address Dependent" filtering, Address-Dependent Filtering, the hole-punching
packet could be sent to the server's discard port (port number 9).
For "Address Address and Port Dependent" filtering NATs Port-Dependent Filtering NATs, the hole-punching
packet must go to the port used for sending UDP packets to the
client. To be able to do that that, the server need needs to include the
"src_addr" in the "Transport" Transport header (which is the "source" transport
parameter in RFC2326). Since UDP packets are inherently unreliable,
to ensure that at least one UDP message passes the NAT, hole-punching
packets should be retransmitted a reasonable number of times.

As hole-punching and keep-alive messages, one

One could have used the RTP No-Op packet [I-D.ietf-avt-rtp-no-op] packets [RTP-NO-OP] as hole-punching
and keep-alive messages had they been defined. That would have
ensured that the traffic would look like RTP and thus would likely
have the least risk of being dropped by any firewall. The drawback
of using RTP No-Op is that the payload type number must be
dynamically assigned through RTSP first. Other options are STUN, a an
RTP packet without any payload, or an a UDP packet without any payload.
For RTCP it is most suitable to use correctly generated RTCP packets.
In general general, sending unsolicited traffic to the RTSP server may
trigger security functions resulting in the blocking of the keep-alive keep-
alive messages or termination of the RTSP session itself.

This method is further brittle as it doesn't support address Address and port
dependent mappings.
Port-Dependent Mappings. Thus, it proposes to use the old STUN
methods to classify the NAT behavior, thus enabling early error
indication. This is strictly not required but will lead to failures
during setup when the NAT has the wrong behavior. This failure can
also occur If if the NAT changes the properties of the existing mapping
and filtering state or between the classification message exchange
and the actual RTSP session setup. setup, for example example, due to load.

4.1.3. ALG considerations Considerations

If a NAT supports RTSP ALG (Application Level Gateway) and is not
aware of the STUN traversal option, service failure may happen,
because a client discovers its NAT external IP address and port
numbers,
numbers and inserts them in its SETUP requests. When the RTSP ALG
processes the SETUP request request, it may change the destination and port
number, resulting in unpredictable behavior. An ALG should not
update address fields which contains that contain addresses other than the NATs NAT's
internal address domain. In cases where the ALG modifies fields
unnecessarily
unnecessarily, two alternatives exist:

1. Use TLS Transport Layer Security (TLS) to encrypt the data over the
RTSP TCP connection to prevent the ALG from reading and modifying
the RTSP messages.

2. Turn off the STUN based STUN-based NAT traversal mechanism mechanism.

As it may be difficult to determine why the failure occurs, the usage
of TLS protected TLS-protected RTSP message exchange at all times would avoid this
issue.

4.1.4. Deployment Considerations

For the Stand-Alone stand-alone usage of STUN STUN, the following applies:

Advantages:

o STUN is a solution first used by applications based on SIP
[RFC3261] based applications
(See section (see Sections 1 and 2 of [RFC5389]). As shown above,
with little or no changes, the RTSP application can re-use reuse STUN as
a NAT traversal solution, avoiding the pit-fall pitfall of solving a
problem twice.

o Using STUN does not require RTSP server modifications, assuming it
is a RTSP 2.0 server that is compliant server; with RTSP 2.0; it only affects the
client implementation.

Disadvantages:

o Requires a STUN server deployed in the same address domain as the
server.

o Only works with NATs that perform endpoint independent Endpoint-Independent and address
dependent mappings.
Address-Dependent Mappings. Address and Port-Dependent filtering Filtering
NATs create some issues.

o Brittle to NATs changing the properties of the NAT mapping and
filtering.

o Does not work with port Address and address dependent mapping Port-Dependent Mapping NATs without
server modifications.

o Will not work if a NAT uses multiple IP addresses, since RTSP
servers generally require all media streams to use the same IP as
used in the RTSP connection to prevent becoming a DDoS tool.

o Interaction problems exist when a an RTSP-aware ALG interferes with
the use of STUN for NAT traversal unless TLS secured TLS-secured RTSP message
exchange is used.

o Using STUN requires that RTSP servers and clients support the
updated RTSP specification [I-D.ietf-mmusic-rfc2326bis], [RTSP], because it is no longer
possible to guarantee that RTP and RTCP ports are adjacent to each
other, as required by the "client_port" and "server_port"
parameters in RFC2326. RFC 2326.

Transition:

The usage of STUN can be phased out gradually as the first step of a
STUN capable
STUN-capable server or client should be to check the presence of
NATs. The removal of STUN capability in the client implementations
will have to wait until there is absolutely no need to use STUN.

4.1.5. Security Considerations

To prevent the RTSP server from being used as Denial of Service Denial-of-Service (DoS)
attack tools tools, the RTSP Transport header parameter parameters "destination" and
"dest_addr" are generally not allowed to point to any IP address
other than the one the RTSP message originates from. The RTSP server
is only prepared to make an exception to this rule when the client is
trusted (e.g., through the use of a secure authentication process, process or
through some secure method of challenging the destination to verify
its willingness to accept the RTP traffic). Such a restriction means
that STUN in general does not work for use cases where RTSP and media
transport go to different addresses.

STUN combined with RTSP that is restricted by destination address restricted RTSP has
the same security properties as the core RTSP. It is protected from
being used as a DoS attack tool unless the attacker has the ability
to spoof the TCP connection carrying RTSP messages.

Using STUN's support for message authentication and the secure
transport of RTSP messages, attackers cannot modify STUN responses or
RTSP messages (TLS) to change the media destination. This protects
against
hijacking, however hijacking; however, as a client can be the initiator of an
attack, these mechanisms cannot securely prevent RTSP servers from
being used as DoS attack tools.

4.2. Server Embedded STUN

4.2.1. Introduction

This Section section describes an alternative to the stand-alone STUN usage
in the previous section that has quite significantly different
behavior.

4.2.2. Embedding STUN in RTSP

This section outlines the adaptation and embedding of STUN within
RTSP. This enables STUN to be used to traverse any type of NAT,
including address Address and Port-Dependent mapping Mapping NATs. This would
require RTSP level RTSP-level protocol changes.

This NAT traversal solution has limitations:

1. It does not work if both the RTSP client and RTSP server are
behind separate NATs.

2. The RTSP server may, for security reasons, refuse to send media
streams to an IP that is different from the IP in the client RTSP
requests.

Deviations from STUN as defined in RFC 5389:

1. The RTSP application must provision the client with an identity
and shared secret to use in the STUN authentication;

2. We require the STUN server to be co-located on the RTSP server's
media source ports.

If the STUN server is co-located with the RTSP server's media source
port, an RTSP client using RTP transport over UDP can use STUN to
traverse ALL types of NATs. In the case of port Address and address dependent mapping Port-
Dependent Mapping NATs, the party on the inside of the NAT must
initiate UDP traffic. The STUN Binding Request, being a UDP packet
itself, can serve as the traffic initiating packet. Subsequently,
both the STUN Binding Response packets and the RTP/RTCP packets can
traverse the NAT, regardless of whether the RTSP server or the RTSP
client is behind NAT (however (however, only one of the them can be behind a NAT).

Likewise, if an RTSP server is behind a NAT, then an embedded STUN
server must be co-located on the RTSP client's RTCP port. Also Also, it
will become the client that needs to disclose his destination address
rather than the server, so the server can correctly determine its NAT
external source address for the media streams. In this case, we
assume that the client has some means of establishing a TCP
connection to the RTSP server behind NAT so as to exchange RTSP
messages with the RTSP server, potentially using a proxy or static
rules.

To minimize delay, we require that the RTSP server supporting this
option must inform the client about the RTP and RTCP ports from where
the server will send out RTP and RTCP packets, respectively. This
can be done by using the "server_port" parameter in RFC2326, RFC 2326 and the
"src_addr" parameter in [I-D.ietf-mmusic-rfc2326bis]. [RTSP]. Both are in the RTSP Transport
header. But in general general, this strategy will require that one first do
does one SETUP request per media to learn the server ports, then
perform the STUN checks, followed by a subsequent SETUP to change the
client port and destination address to what was learned during the
STUN checks.

To be certain that RTCP works correctly correctly, the RTSP end-point endpoint (server or
client) will be required to send and receive RTCP packets from the
same port.

4.2.3. Discussion On on Co-located STUN Server

In order to use STUN to traverse "address Address and port dependent"
filtering Port-Dependent Filtering
or mapping NATs Mapping NATs, the STUN server needs to be co-located with the
streaming server media output ports. This creates a de-
multiplexing demultiplexing
problem: we must be able to differentiate a STUN packet from a media
packet. This will be done based on heuristics. The existing STUN
heuristics is the first byte in the packet and the Magic Cookie field
(added in RFC5389), RFC 5389), which works fine between STUN and RTP or RTCP
where the first byte happens to be different. Thanks to the magic cookie field Magic
Cookie field, it is unlikely that other protocols would be mistaken
for a STUN packet, but this is not assured. For more discussion of
this, please see Section 5.1.2 of [RFC5764].

4.2.4. ALG considerations Considerations

The same ALG traversal considerations as for Stand-Alone stand-alone STUN applies
(Section 4.1.3).

4.2.5. Deployment Considerations

For the "Embedded STUN" method the following applies:

Advantages:

o STUN is a solution first used by SIP applications. As shown
above, with little or no changes, the RTSP application can re-use reuse
STUN as a NAT traversal solution, avoiding the pit-fall pitfall of solving
a problem twice.

o STUN has built-in message authentication features, which makes it
more secure against hi-jacking hijacking attacks. See the next section for
an in-depth security discussion.

o This solution works as long as there is only one RTSP endpoint in
the private address realm, regardless of the NAT's type. There
may even be multiple NATs (see Figure 1 in [RFC5389]).

o Compared to other UDP based UDP-based NAT traversal methods in this
document, STUN requires little new protocol development (since
STUN is already a an IETF standard), and most likely less
implementation effort, since open source STUN server and client
implementations are available [STUN-IMPL][PJNATH]. [STUN-IMPL] [PJNATH].

Disadvantages:

o Some extensions to the RTSP core protocol, likely signaled by RTSP
feature tags, must be introduced.

o Requires an embedded STUN server to be co-located on each of the
RTSP server's media protocol's ports (e.g. (e.g., RTP and RTCP ports),
which means more processing is required to de-multiplex demultiplex STUN
packets from media packets. For example, the de-multiplexer demultiplexer must
be able to differentiate a an RTCP RR packet from a STUN packet, packet and
forward the former to the streaming server, server and the latter to the
STUN server.

o Does not support use cases that require the RTSP connection and
the media reception to happen at different addresses, unless the
server's security policy is relaxed.

o Interaction problems exist when a an RTSP ALG is not aware of STUN
unless TLS is used to protect the RTSP messages.

o Using STUN requires that RTSP servers and clients support the
updated RTSP specification [I-D.ietf-mmusic-rfc2326bis], [RTSP], and they both agree to support
the NAT traversal feature.

o Increases the setup delay with at least the amount of time it
takes to perform STUN message exchanges. Most likely an extra
SETUP sequence will be required.

Transition:

The usage of STUN can be phased out gradually as the first step of a
STUN capable
STUN-capable machine can be used to check the presence of NATs for
the presently used network connection. The removal of STUN
capability in the client implementations will have to wait until
there is absolutely no need to use STUN, i.e. i.e., no NATs or firewalls.

4.2.6. Security Considerations

See Stand-Alone STUN (Section 4.1.5).

4.3. ICE

4.3.1. Introduction

ICE (Interactive

Interactive Connectivity Establishment) Establishment (ICE) [RFC5245] is a
methodology for NAT traversal that has been developed for SIP using
SDP offer/answer. The basic idea is to try, in a staggered parallel
fashion, all possible connection addresses that in which an endpoint may
be
reachable by. reached. This allows the endpoint to use the best available UDP
"connection" (meaning two UDP end-points endpoints capable of reaching each
other). The methodology has very nice properties in that basically
all NAT topologies are possible to traverse.

Here is how ICE works at a high level. End point Endpoint A collects all
possible addresses that can be used, including local IP addresses,
STUN derived
STUN-derived addresses, TURN Traversal Using Relay NAT (TURN) addresses,
etc. On each local port that any of these address and port pairs
lead to, a STUN server is installed. This STUN server only accepts
STUN requests using the correct authentication through the use of a
username and password.

End-point

Endpoint A then sends a request to establish connectivity with end-
point
endpoint B, which includes all possible "destinations" [RFC5245] to
get the media through to A. Note that each of A's local address/port
pairs (host candidates and server reflexive base) has a co-located
STUN server
co-located. server. B in turn provides A with all its possible destinations
for the different media streams. A and B then uses a STUN client to
try to reach all the address and port pairs specified by A from its
corresponding destination ports. The destinations for which the STUN
requests successfully complete are then indicated and one is
selected.

If B fails to get any STUN response from A, all hope is not lost.
Certain NAT topologies require multiple tries from both ends before
successful connectivity is accomplished and therefore accomplished; therefore, requests are
retransmitted multiple times. The STUN requests may also result in
that
more connectivity alternatives (destinations) are being discovered and
conveyed in the STUN responses.

4.3.2. Using ICE in RTSP

The usage of ICE for RTSP requires that both client and server be
updated to include the ICE functionality. If both parties implement
the necessary functionality functionality, the following steps could provide ICE
support for RTSP.

This assumes that it is possible to establish a TCP connection for
the RTSP messages between the client and the server. This is not
trivial in scenarios where the server is located behind a NAT, and
may require some TCP ports be opened, or the deployment of proxies, proxies are deployed, etc.

The negotiation of ICE in RTSP of necessity will work different than
in SIP with SDP offer/answer. The protocol interactions are
different
different, and thus the possibilities for transfer of states are also
somewhat different. The goal is also to avoid introducing extra
delay in the setup process at least for when the server is not behind
a NAT in regards to the client, and the client is either having an
address in the same address domain, domain or is behind NAT(s) the NAT(s), which can
address the address domain of the server. This process is only
intended to support PLAY mode, i.e. i.e., media traffic flows from server
to client.

1. The ICE usage begins in the SDP. The SDP for the service indicates
that ICE is supported at the server. No candidates can be given
here as that would not work with the on demand, DNS load balancing,
etc., that which have the SDP indicate a resource on a server park
rather than a specific machine.

2. The client gathers addresses and puts together its candidates for
each media stream indicated in the session description.

3. In each SETUP request request, the client includes its candidates in an
ICE specific
ICE-specific transport specification. This indicates for For the
server server, this
indicates the ICE support by the client. One candidate is the
most prioritized candidate and here the prioritization for this
address should be somewhat different compared to SIP. High High-
performance candidates is are recommended rather than candidates
with the highest likellihood likelihood of success, as it is more likely that
a server is not behind a NAT compared to a SIP user-agent. user agent.

4. The server responds to the SETUP (200 OK) for each media stream
with its candidates. A server not behind a NAT usually only
provides a single ICE candidate. Also Also, here one candidate is the
server primary address.

5. The connectivity checks are performed. For the server server, the
connectivity checks from the server to the clients have an
additional usage. They verify that there is someone willing to
receive the media, thus preventing the server from unknowingly
performing a DoS attack.

6. Connectivity checks from the client promoting a candidate pair
were successful. Thus Thus, no further SETUP requests are necessary
and processing can proceed with step 7. If another an address other than
the primary has been verified by the client to work, that address
may then be promoted for usage in a SETUP request (Go (go to step 7).
If the checks for the available candidates failed and if further
candidates have been derived during the connectivity checks, then
those can be signalled signaled in new candidate lines in a SETUP request
updating the list (Go (go to step 5).

7. Client issues the PLAY request. If the server also has completed
its connectivity checks for the promoted candidate pair (based on
the username as it may be derived addresses if the client was
behind
NAT) NAT), then it can directly answer 200 OK (Go (go to step 8).
If the connectivity check has not yet completed completed, it responds with
a 1xx code to indicate that it is verifying the connectivity. If
that fails within the set timeout, an error is reported back. Client
The client needs to go back to step 6.

8. Process completed and media can be delivered. ICE candidates not
used may be released.

To keep media paths alive alive, the client needs to periodically send data
to the server. This will be realized with STUN. RTCP sent by the
client should be able to keep RTCP open open, but STUN will also be used
for SIP based on the same motivations as for ICE for SIP. ICE.

4.3.3. Implementation burden Burden of ICE

The usage of ICE will require that a number of new protocols and new
RTSP/SDP features be implemented. This makes ICE the solution that
has the largest impact on client and server implementations among all
the NAT/firewall traversal methods in this document.

RTSP server implementation requirements are:

o STUN server features

o Limited STUN client features

o SDP generation with more parameters. parameters

o RTSP error code for ICE extension

RTSP client implementation requirements are:

o Limited STUN server features

o Limited STUN client features

o RTSP error code and ICE extension

4.3.4. ALG Considerations

If there is an RTSP ALG that doesn't support the NAT traversal
method, it may interfere with the NAT traversal. As the usage of ICE
for the traversal manifest manifests itself in the RTSP message primarily as a
new transport specification, an ALG that passes through unknown will
not prevent the traversal. An ALG that discards unknown
specifications will however will, however, prevent the NAT traversal. These
issues can be avoided by preventing the ALG to interfere with the signalling
signaling by using TLS for the RTSP message transport.

An ALG that supports this traversal method, can method can, on the most basic
level
level, just pass the transport specifications through. ALGs in NATs
and Firewalls firewalls could use the ICE candidates to establish a filtering
state that would allow incoming STUN messages prior to any outgoing
hole-punching packets, and in that way it could speed up the
connectivity checks and reduce the risk of failures.

4.3.5. Deployment Considerations

Advantages:

o Solves NAT connectivity discovery for basically all cases as long
as a TCP connection between the client and server can be
established. This includes servers behind NATs. (Note that a
proxy between address domains may be required to get TCP through). through.)

o Improves defenses against DDoS attacks, since a media receiving media-receiving
client requires authentications, authentications via STUN on its media reception
ports.

Disadvantages:

o Increases the setup delay with at least the amount of time it
takes for the server to perform its STUN requests.

o Assumes that it is possible to de-multiplex demultiplex between the packets of
the media protocol and STUN packets. This is possible for RTP as
discussed
discussed, for example example, in Section 5.1.2 of [RFC5764].

o Has a fairly high implementation burden put on both the RTSP
server and client. However, several Open Source open source ICE
implementations do exist, such as [NICE][PJNATH]. [NICE] and [PJNATH].

4.3.6. Security Consideration Considerations

One should review the security consideration Security Considerations section of ICE and STUN
to understand that ICE contains some potential issues. However However,
these can be avoided by correctly using ICE in RTSP. An important
factor is to secure the signalling, i.e. signaling, i.e., use TLS between the RTSP
client and server. In fact ICE does help avoid the DDoS attack issue
with RTSP substantially as it reduces the possibility for a DDoS
using RTSP servers to on attackers that are on-path on path between the RTSP
server and the target and capable of intercepting the STUN
connectivity check packets and correctly send sending a response to the
server. The ICE connectivity checks with their random transaction
IDs from the server to the client serves as a return-routability
check and prevents off-
path attacker off-path attackers to succeed with address
spoofing. Similar This is similar to Mobile
IPV6's IPv6's return routability
procedure (Section 5.2.5 of [RFC6275]).

4.4. Latching

4.4.1. Introduction

Latching is a NAT traversal solution that is based on requiring RTSP
clients to send UDP packets to the server's media output ports.
Conventionally, RTSP servers send RTP packets in one direction: from
server to client. Latching is similar to connection-oriented
traffic, where one side (e.g., the RTSP client) first "connects" by
sending a an RTP packet to the other side's RTP port, port; the recipient
then replies to the originating IP and port. Port. This method is also
referred to as "Late "late binding". It requires that all RTP/RTCP
transport is be done symmetrical, i.e. symmetrically. This in effect requires Symmetric
RTP [RFC4961]. There exist Refer to [RFC7362] for a description for latching of SIP negotiated the Latching
of SIP-negotiated media streams in Session Border Controllers [RFC7362]. Controllers.

Specifically, when the RTSP server receives the latching Latching packet
(a.k.a. hole-punching packet, since it is used to punch a hole in the
firewall/NAT and to aid the server for port binding and address
mapping)
firewall/NAT) from its client, it copies the source IP and Port
number and uses them as the delivery address for media packets. By
having the server send media traffic back the same way as the
client's packet packets are sent to the server, address and port mappings
will be honored. Therefore Therefore, this technique works for all types of
NATs, given that the server is not behind a NAT. However, it does
require server modifications. The format of the latching Latching packet will
have to be defined.

Latching is very vulnerable to both hijacking and becoming a tool in
Distributed Denial of Service (DDoS)
DDoS attacks (See (see Security Considerations of [RFC7362]), in [RFC7362]) because
attackers can simply forge the source IP & and Port of the latching Latching
packet. Using the The rule for restricting IP address addresses to the one of the
signaling connection connections will need to be applied here also. However,
that does not protect against hijacking from another client behind
the same NAT. This can become a serious issue in deployments with
CGNs.

4.4.2. Necessary RTSP extensions Extensions

To support Latching, the RTSP signaling must be extended to allow the
RTSP client to indicate that it will use Latching. The client also
needs to be able to signal its RTP SSRC to the server in its SETUP
request. The RTP SSRC is used to establish some basic level of
security against hijacking attacks or simply to avoid mis-association
when multiple clients are behind the same NAT. Care must be taken in
choosing clients' RTP SSRC. First, it must be unique within all the
RTP sessions belonging to the same RTSP session. Secondly, Second, if the RTSP
server is sending out media packets to multiple clients from the same
send port, the RTP SSRC needs to be unique among those clients' RTP
sessions. Recognizing that there is a potential that RTP SSRC
collisions may occur, the RTSP server must be able to signal to a
client that a collision has occurred and that it wants the client to
use a different RTP SSRC carried in the SETUP response or use unique
ports per RTSP session. Using unique ports limits an RTSP server in
the number of sessions it can simultaneously handle per interface IP
addresses.

The latching Latching packet as discussed above should have a field which that can
contain an a client and RTP session identifier to correctly associate
the latching Latching packet with the correct context. If an RTP packet is to
be used, there would have been be a benefit to use using a well defined well-defined RTP payload
format for this purpose as the No-Op payload format proposed
[I-D.ietf-avt-rtp-no-op].
[RTP-NO-OP]. However, in the absence of such a
specification specification, an RTP
packet without a payload could be used. Using SSRC has the benefit that is beneficial
because RTP and RTCP both would work as is. However, also other packet
formats could be used that carry the necessary identification of the
context, and such a solution is discussed in Section 4.5.

4.4.3. ALG Considerations

An RTSP ALG not supporting this method could interfer interfere with the
methods used to indicate that latching Latching is to be done, as well as the
SSRC signalling. Thus signaling, thus preventing the method from working. However, if
the RTSP ALG instead opens the corresponding pinholes and create creates the
necessary mapping in the NAT, traversal will still work. Securing
the RTSP message transport using TLS will avoid this issue.

An RTSP ALG that support supports this traversal method can for basic
functionality simply pass the related signalling signaling parameters
transparently. Due to the security considerations for latching it Latching,
there might exist a benefit for an RTSP ALG that will enable NAT
traversal to negotiate with the path and turn off the latching Latching
procedures when the ALG handles this. However, this opens up to
failure modes when there are multiple levels of NAT and only one
supports an RTSP ALG.

4.4.4. Deployment Considerations

Advantages:

o Works for all types of client-facing NATs. (Requirement NATs (requirement 1 in
Section 3).

o Has little interaction problems with any RTSP ALG changing the
client's information in the transport Transport header.

Disadvantages:

o Requires modifications to both the RTSP server and client.

o Limited to work working with servers that are not behind a NAT.

o The format of the packet for "connection setup" (a.k.a Latching
packet) is not defined.

o SSRC management if RTP is used for latching Latching due to risk for mis-
association of clients to RTSP sessions at the server if SSRC
collision occurs.

o Has significant security considerations (See Section 4.4.5), due
to the lack of a strong authentication mechanism and will need to
use address restrictions.

4.4.5. Security Consideration Considerations

Latching's major security issue is that RTP streams can be hijacked
and directed towards any target that the attacker desires unless
address restrictions are used. In the case of NATs with multiple
clients on the inside of them, hijacking can still occur. This
becomes a significant threat in the context of carrier grade NATs
(CGN). CGNs.

The most serious security problem is the deliberate attack with the
use of a an RTSP client and Latching. The attacker uses RTSP to setup set up
a media session. Then it uses Latching with a spoofed source address
of the intended target of the attack. There is no defense against
this attack other than restricting the possible address a latching Latching
packet can come from to the same address as the RTSP TCP connection are
is from. This prevents Latching to be used in use cases that require
different addresses for media destination and signalling. signaling. Even
allowing only a limited address range containing the signalling signaling
address from where
latching Latching is allowed opens up a significant
vulnerability as it is difficult to determine the address usage for
the network the client connects from.

A hijack attack can also be performed in various ways. The basic
attack is based on the ability to read the RTSP signaling packets in
order to learn the address and port the server will send from and
also the SSRC the client will use. Having this information information, the
attacker can send its own Latching packets containing the correct RTP
SSRC to the correct address and port on the server. The RTSP server
will then use the source IP and port Port from the Latching packet as the
destination for the media packets it sends.

Another variation of this attack is for a man in the middle to modify
the RTP latching Latching packet being sent by a client to the server by
simply changing the source IP and port Port to the target one desires to
attack.

One can fend off the snooping based snooping-based attack by applying encryption to
the RTSP signaling transport. However, if the attacker is a man in
the middle modifying latching Latching packets, the attack is impossible to
defend against other than through address restrictions. As a NAT re-
writes
rewrites the source IP and (possibly) port port, this cannot be
authenticated, but authentication is required in order to protect
against this type of DoS attack.

Yet another issue is that these attacks also can be used to deny the
client the service it desires from the RTSP server completely. The
attacker modifies or originates its own latching Latching packets with another a port
other than what the legit latching Latching packets uses, use, which results in that the
media server sends sending the RTP/RTCP traffic to ports the client isn't
listening for RTP/RTCP on.

The amount of random non-guessable material in the latching Latching packet
determines how well Latching can fend off stream-hijacking stream hijacking performed
by parties that are off the client to server client-to-server network path, i.e. i.e., it
lacks the capability to see the client's latching Latching packets. The
proposal above uses the 32-bit RTP SSRC field to this effect. Therefore
Therefore, it is important that this field is derived with a non-predictable non-
predictable random number generator. It should not be possible by
knowing the algorithm used and a couple of basic facts, facts to derive what
random number a certain client will use.

An attacker not knowing the SSRC but aware of which port numbers that
a server sends from can deploy a brute force brute-force attack on the server by
testing a lot of different SSRCs until it finds a matching one.
Therefore
Therefore, a server could implement functionality that blocks packets
to ports or from sources that receive or send multiple Latching
packets with different invalid SSRCs, especially when they are coming
from the same IP/Port. IP and Port. Note that this mitigation in itself opens
up a new venue for DoS attacks against legit users trying to latch.

To improve the security against attackers attackers, the amount of random
material could be increased. To achieve a longer random tag while
still using RTP and RTCP, it will be necessary to develop RTP and
RTCP payload formats for carrying the random material.

4.5. A Variation to Latching

4.5.1. Introduction

Latching as described above requires the usage of a valid RTP format
as the Latching packet, i.e. i.e., the first packet that the client sends
to the server to establish a bi-directional bidirectional transport flow for RTP
streams. There is currently no appropriate RTP packet format for
this purpose, although the RTP No-Op format was a proposal to fix the
problem [I-D.ietf-avt-rtp-no-op], [RTP-NO-OP]; however, that work was abandoned.
There exists a RFC that [RFC6263]
discusses the implication of different type types of packets as keep-alives keep-
alives for RTP [RFC6263] RTP, and its findings are very relevant to the format of
the Latching packet.

Meanwhile, there has have been NAT/firewall traversal techniques deployed
in the wireless streaming market place that use non-RTP messages as
Latching packets. This section describes a variant based on a subset
of those solutions that alters the previously described Latching
solution.

4.5.2. Necessary RTSP extensions Extensions

In this variation of Latching, the Latching packet is a small UDP
packet that does not contain an RTP header. In response to the
client's Latching packet, the RTSP server sends back a similar
Latching packet as a confirmation so the client can stop the so so-
called "connection phase" of this NAT traversal technique.
Afterwards, the client only has to periodically send Latching packets
as keep-alive messages for the NAT mappings.

The server listens on its RTP-media output port, port and tries to decode
any received UDP packet as the Latching packet. This is valid since
an RTSP server is not expecting RTP traffic from the RTSP client.
Then, it can correlate the Latching packet with the RTSP client's
session ID or the client's SSRC, SSRC and record the NAT bindings
accordingly. The server then sends a Latching packet as the response
to the client.

The Latching packet can contain the SSRC to identify the RTP stream,
and care must be taken if the packet is bigger than 12 bytes,
ensuring that it is distinctively different from RTP packets, whose
header size is 12 bytes.

RTSP signaling can be added to do the following:

1. Enable or disable such Latching message exchanges. When the
firewall/NAT has an RTSP-aware ALG, it is possible to disable
Latching message exchange and let the ALG work out the address
and port mappings.

2. Configure the number of re-tries retries and the re-try retry interval of the
Latching message exchanges.

4.5.3. ALG Considerations

See Latching ALG consideration considerations in Section 4.4.3.

4.5.4. Deployment Considerations

This approach has the following advantages when compared with the
Latching approach (Section 4.4):

1. There is no need to define an RTP payload format for firewall
traversal, therefore
traversal; therefore, it is more simple to use, implement implement, and
administer (Requirement (requirement 4 in Section 3), instead 3) than a Latching
protocol protocol,
which must be defined.

2. When properly defined, this kind of Latching packet exchange can
also authenticate RTP receivers, to prevent hijacking attacks.

This approach has the following disadvantages disadvantage when compared with the
Latching approach:

1. The server's sender SSRC for the RTP stream or other session
Identity information must be signaled in the RTSP's SETUP
response, in the Transport header of the RTSP SETUP response.

4.5.5. Security Considerations

Compared to the security properties of Latching Latching, this variant is
slightly improved. First of all it allows for a larger random field
in the Latching packets packets, which makes it more unlikely for an off-path
attacker to succeed in a hi-jack hijack attack. Secondly Second, the confirmation
allows the client to know when Latching works and when it didn't doesn't and
thus when to restart the Latching process by updating the SSRC.

Still

Still, the main security issue remain remaining is that the RTSP server
can't know that the source address in the latching Latching packet was coming
from a an RTSP client wanting to receive media and not from one that
likes to direct the media traffic to an a DoS target.

4.6. Three Way Three-Way Latching

4.6.1. Introduction

The three way latching

Three-Way Latching is an attempt to try to resolve the most
significant security issues for both previously discussed variants of
Latching. By adding a server request response exchange directly
after the initial latching Latching, the server can verify that the target
address present in the latching Latching packet is an active listener and
confirm its desire to establish a media flow.

4.6.2. Necessary RTSP extensions Extensions

Uses the same RTSP extensions as the alternative latching Alternative Latching method
(Section 4.5) uses. The extensions for this variant are only in the
format and transmission of the Latching packets.

The client to server latching client-to-server Latching packet is similar to the Alternative
Latching (Section 4.5), i.e. an i.e., a UDP packet with some session
identifier
identifiers and a random value. When the server responds to the
Latching packet with a Latching confirmation, it includes a random
value (Nonce) (nonce) of its own in addition to echoing back the one the
client sent. Then a third message is added to the exchange. The
client acknowledges the reception of the Latching confirmation
message and echoes back the server's nonce. Thus nonce, thus confirming that the
Latched address goes to a an RTSP client that initiated the latching Latching
and is actually present at that address. The RTSP server will refuse
to send any media until the Latching Acknowledgement has been
received with a valid nonce.

4.6.3. ALG Considerations

See Latching ALG consideration considerations in Section 4.4.3.

4.6.4. Deployment Considerations

A solution with a 3-way three-way handshake and its own Latching packets
can be compared with the ICE-based solution (Section 4.3) and have
the following differences:

o Only works for servers that are not behind a NAT.

o May be simpler to implement due to the avoidance of the ICE
prioritization and check-board mechanisms.

However, a 3-way Three-Way Latching protocol is very similar to using STUN
in both directions as a Latching and verification protocol. Using
STUN would remove the need for implementing a new protocol.

4.6.5. Security Considerations

Three way latching

Three-Way Latching is significantly more secure than its simpler
versions discussed above. The client to server nonce client-to-server nonce, which is
included in signalling signaling and also can be bigger than the 32-bits 32 bits of
random data that the SSRC field supports supports, makes it very difficult for
an off-path attacker to perform an denial of service a DoS attack by diverting the media.

The client to server client-to-server nonce and its echoing back does not protect
against on-patch attacker, on-path attackers, including malicious clients. However, the
server to client
server-to-client nonce and its echoing back prevents malicious
clients to divert the media stream by spoofing the source address and
port, as it can't echo back the nonce in these cases. Similar This is
similar to the Mobile IPv6 return routability procedure
(Section 5.2.5 of [RFC6275])

Three way latching [RFC6275]).

Three-Way Latching is really only vulnerable to an on-path attacker
that is quite capable. First First, the attacker can either learn the
client to server nonce, client-
to-server nonce either by intercepting the signalling, signaling or by modifying
the source information (target destination) of a client's latching Latching
packet. Secondly, Second, it is also on-path between the server and target
destination and can generate a response using the server's nonce. An
adversary that has these capabilities are is commonly capable of causing
significantly worse damage than this using other methods.

Three-way latching do

Three-Way Latching results in that the server to client server-to-client packet is being
bigger than the client to server client-to-server packet, due to the inclusion of the
server to client
server-to-client nonce in addition to the client to server client-to-server nonce.
Thus
Thus, an amplification effect do exist, does exist; however, to achieve this
amplification effect effect, the attacker has to create a session state on
the RTSP server. The RTSP server can also limit the number of
response
responses it will generate before considering the latching Latching to be
failed.

4.7. Application Level Gateways

4.7.1. Introduction

An Application Level Gateway (ALG) ALG reads the application level messages and performs necessary
changes to allow the protocol to work through the middle box. However middlebox.
However, this behavior has some problems in regards to RTSP:

1. It does not work when the RTSP protocol is used with end-to-end security. As
the ALG can't inspect and change the application level messages messages,
the protocol will fail due to the middle box. middlebox.

2. ALGs need to be updated if extensions to the protocol are added.
Due to deployment issues with changing ALGs ALGs, this may also break
the end-to-end functionality of RTSP.

Due to the above reasons reasons, it is not recommended to use an RTSP ALG in
NATs. This is especially important for NATs targeted to home users
and small office environments, since it is very hard to upgrade NATs
deployed in home or SOHO (small office/home office) environment. environments.

4.7.2. Outline On how on How ALGs for RTSP work Work

In this section, we provide a step-by-step outline on how one could
go about writing an ALG to enable RTSP to traverse a NAT.

1. Detect any SETUP request.

2. Try to detect the usage of any of the NAT traversal methods that
replace the address and port of the Transport header parameters
"destination" or "dest_addr". If any of these methods are used,
then the ALG should not change the address. Ways to detect that
these methods are used are:

* For embedded STUN, it would be to watch for a feature tag,
like "nat.stun". If "nat.stun", and to see if any of those exists exist in the
"supported", "proxy-require", or "require" headers of the RTSP
exchange.

* For stand alone stand-alone STUN and TURN based TURN-based solutions: This can be
detected by inspecting the "destination" or "dest_addr"
parameter. If it contains either one of the NAT's external IP
addresses or a public IP address address, then such a solution is in
use. However However, if multiple NATs are used used, this detection may
fail. Remapping should only be done for addresses belonging
to the NAT's own private address space.

Otherwise

Otherwise, continue to the next step.

3. Create UDP mappings (client given IP/port IP and Port <-> external IP/port) IP and
Port) where needed for all possible transport specifications in
the
transport Transport header of the request found in (1). (step 1). Enter the
external address and port(s) of these mappings in transport the Transport
header. Mappings shall be created with consecutive external port
numbers starting on an even number for RTP for each media stream.
Mappings should also be given a long timeout period, at least 5
minutes.

4. When the SETUP response is received from the server, the ALG may
remove the unused UDP mappings, i.e. i.e., the ones not present in the
transport
Transport header. The session ID should also be bound to the UDP
mappings part of that session.

5. If the SETUP response settles on RTP over TCP or RTP over RTSP as
lower transport, do nothing: let TCP tunneling take care of NAT
traversal. Otherwise Otherwise, go to the next step.

6. The ALG should keep the UDP mappings belonging to the RTSP
session as long as: an RTSP message with the session's ID has
been sent in the last timeout interval, or a UDP message has been
sent on any of the UDP mappings during the last timeout interval.

7. The ALG may remove a mapping as soon as a TEARDOWN response has
been received for that media stream.

4.7.3. Deployment Considerations

Advantage:

Advantages:

o No impact on either client or server server.

o Can work for any type of NATs

Disadvantage: NATs.

Disadvantages:

o When deployed deployed, they are hard to update to reflect protocol
modifications and extensions. If not updated updated, they will break the
functionality.

o When end-to-end security is used, the ALG functionality will fail.

o Can interfere with other types of traversal mechanisms, such as
STUN.

Transition:

An RTSP ALG will not be phased out in any automatic way. It must be
removed, probably through the removal or update of the NAT it is
associated with.

4.7.4. Security Considerations

An ALG will not work with deployment of end-to-end RTSP signaling
security, however
security; however, it will work with the hop-by-hop security method
defined in Section 19.3 of RTSP 2.0 [I-D.ietf-mmusic-rfc2326bis].
Therefore [RTSP]. Therefore, deployment of
ALG may result in clients located behind NATs not using end-to-end
security, or more likely the selection of a NAT traversal solution
that allow allows for security.

The creation of an a UDP mapping based on the signalling signaling message has some
potential security implications. First of all all, if the RTSP client
releases its ports and another application are is assigned these
instead instead,
it could receive RTP media as long as the mappings exist and the RTSP
server has failed to be signalled signaled or notice the lack of client
response.

A NAT with RTSP ALG that assigns mappings based on SETUP requests
could potentially become the victim of a resource exhaustion attack.
If an attacker creates a lot of RTSP sessions, even without starting
media transmission transmission, this could exhaust the pool of available UDP
ports on the NAT. Thus Thus, only a limited number of UDP mappings should
be allowed to be created by the RTSP ALG.

4.8. TCP Tunneling

4.8.1. Introduction

Using a TCP connection that is established from the client to the
server ensures that the server can send data to the client. The
connection opened from the private domain ensures that the server can
send data back to the client. To send data originally intended to be
transported over UDP requires the TCP connection to support some type
of framing of the media data packets. Using TCP also results in the
client having to accept that real-time performance can be impacted.
TCP's problem of ensuring timely delivery was one of the reasons why
RTP was developed. Problems that arise with TCP are: head-of-line
blocking, delay introduced by retransmissions, and a highly varying
rate due to the congestion control algorithm. If a sufficient amount
of buffering (several seconds) in the receiving client can be tolerated
tolerated, then TCP will clearly work.

4.8.2. Usage of TCP tunneling Tunneling in RTSP

The RTSP core specification [I-D.ietf-mmusic-rfc2326bis] [RTSP] supports interleaving of media
data on the TCP connection that carries RTSP signaling. See section
Section 14 in [I-D.ietf-mmusic-rfc2326bis] [RTSP] for how to perform this type of TCP tunneling.
There also exists another way of transporting RTP over TCP TCP, which is
defined in Appendix C.2 in
[I-D.ietf-mmusic-rfc2326bis]. [RTSP]. For signaling and rules on how to
establish the TCP connection in lieu of UDP, see appendix Appendix C.2 in
[I-D.ietf-mmusic-rfc2326bis].
[RTSP]. This is based on the framing of RTP over the TCP connection
as described in RFC 4571 [RFC4571].

4.8.3. ALG Considerations

An RTSP ALG will face a different issue with TCP tunneling, at least
the Interleaved interleaved version. Now the full data stream will flow can end up flowing
through the ALG implementation. Thus Thus, it is important that the ALG
is efficient in dealing with the interleaved media data frames to
avoid consuming to much resource many resources and thus creating performance
issues.

The RTSP ALG can also effect affect the transport specifications that
indicate that TCP tunneling can be done and its priortization, prioritization,
including removing the transport specification, thus preventing TCP
tunneling.

4.8.4. Deployment Considerations

Advantage:

o Works through all types of NATs where the RTSP server in is not NATed
or is at least reachable like it was not.

Disadvantage:

Disadvantages:

o Functionality needs to be implemented on both server and client.

o Will not always meet multimedia stream's real-time requirements.

Transition:

The tunneling over RTSP's TCP connection is not planned to be phased- phased
out. It is intended to be a fallback mechanism and for usage when
total media reliability is desired, even at the potential price of
loss of real-time properties.

4.8.5. Security Considerations

The TCP tunneling of RTP has no known significant security problems
besides those already presented in the RTSP specification. It is
difficult to get any amplification effect for denial of service DoS attacks due to
TCP's flow control. The RTSP server server's TCP socket,
independently if independently
used for media tunneling or only RTSP messages messages, can be used for a
redirected syn attack. By spoofing the source address of any TCP
init packets, the TCP SYNs from the server can be directed towards a
target.

A possible security consideration, when session media data is
interleaved with RTSP, would be the performance bottleneck when RTSP
encryption is applied, since all session media data also needs to be
encrypted.

4.9. TURN (Traversal Using Relay NAT)

4.9.1. Introduction Traversal Using Relay Relays around NAT (TURN)

4.9.1. Introduction

TURN [RFC5766] is a protocol for setting up traffic relays that allow
clients behind NATs and firewalls to receive incoming traffic for
both UDP and TCP. These relays are controlled and have limited
resources. They need to be allocated before usage. TURN allows a
client to temporarily bind an address/
port address/port pair on the relay (TURN
server) to its local source address/port pair, which is used to
contact the TURN server. The TURN server will then forward packets
between the two sides of the relay.

To prevent DoS attacks on either recipient, the packets forwarded are
restricted to the specific source address. On the client side side, it is
restricted to the source setting up the allocation. On the external
side this
side, it is limited to the source address/port pair that have been
given permission by the TURN client creating the allocation. Packets
from any other source on this address will be discarded.

Using a TURN server makes it possible for a an RTSP client to receive
media streams from even an unmodified RTSP server. However However, the
problem is those RTSP servers most likely restrict media destinations
to no other IP address than the one the RTSP message arrives from.
This means that TURN could only be used if the server knows and
accepts that the IP belongs to a TURN server server, and the TURN server
can't be targeted at an unknown address. Alternatively, both the
RTSP TCP connection as well as the RTP media is relayed through the
same TURN server.

4.9.2. Usage of TURN with RTSP

To use a TURN server for NAT traversal, the following steps should be
performed.

1. The RTSP client connects with the RTSP server. The client
retrieves the session description to determine the number of
media streams. To avoid the issue with of having the RTSP connection
and media traffic from different addresses also addresses, the TCP connection
must also be done through the same TURN server as the one in the
next step. This will require the usage of TURN for TCP
[RFC6062].

2. The client establishes the necessary bindings on the TURN server.
It must choose the local RTP and RTCP ports that it desires to
receive media packets. TURN supports requesting bindings of even
port numbers and contiguous ranges.

3. The RTSP client uses the acquired address and port allocations in
the RTSP SETUP request using the destination header.

4. The RTSP Server server sends the SETUP reply, which must include the
transport headers src_addr
Transport header's "src_addr" parameter (source and port in RTSP
1.0). Note that the server is required to have a mechanism to
verify that it is allowed to send media traffic to the given
address unless TCP relaying of the RTSP messages also is
performed.

5. The RTSP Client client uses the RTSP Server's server's response to create TURN
permissions for the server's media traffic.

6. The client requests that the server starts playing. The server
starts sending media packets to the given destination address and
ports.

7. Media packets arrive at the TURN server on the external port; If if
the packets match an established permission, the TURN server
forwards the media packets to the RTSP client.

8. If the client pauses and media is not sent for about 75% of the
mapping timeout timeout, the client should use TURN to refresh the
bindings.

4.9.3. ALG Considerations

As the RTSP client inserts the address information of the TURN
relay's external allocations in the SETUP messages, and the ALG that
replaces the address, without considering that the address do does not
belong to the internal address realm of the NAT, will prevent this
mechanism from working. This can be prevented by securing the RTSP
signalling.
signaling.

4.9.4. Deployment Considerations

Advantages:

o Does not require any server modifications given that the server
includes the src_addr "src_addr" header in the SETUP response.

o Works for any type of NAT as long as the RTSP server has a
reachable IP address that is not behind a NAT.

Disadvantage:

Disadvantages:

o Requires another network element, namely the TURN server.

o A TURN server for RTSP may not scale since the number of sessions
it must forward is proportional to the number of client media
sessions.

o The TURN server becomes a single point of failure.

o Since TURN forwards media packets, as a necessity it necessarily introduces
delay.

o An RTSP ALG may change the necessary destinations parameter. This
will cause the media traffic to be sent to the wrong address.

Transition:

TURN is not intended to be phased-out completely, phased out completely; see Section 19 of
[RFC5766]. However However, the usage of TURN could be reduced when the
demand for having NAT traversal is reduced.

4.9.5. Security Considerations

The TURN server can become part of a denial of service DoS attack towards any victim.
To perform this attack attack, the attacker must be able to eavesdrop on the
packets from the TURN server towards a target for the DoS attack.
The attacker uses the TURN server to setup a set up an RTSP session with
media flows going through the TURN server. The attacker is in fact
creating TURN mappings towards a target by spoofing the source
address of TURN requests. As the attacker will need the address of
these mappings mappings, he must be able to eavesdrop or intercept the TURN
responses going from the TURN server to the target. Having these
addresses, he can set up a an RTSP session and start delivery of the
media. The attacker must be able to create these mappings. The
attacker in this case may be traced by the TURN username in the
mapping requests.

This attack requires that the attacker has access to a user account
on the TURN server to be able to set up the TURN mappings. To
prevent this attack attack, the RTSP server needs to verify that the
ultimate target destination accept accepts this media stream. Which stream, which would
require something like ICE's connectivity checks being run between
the RTSP server and the RTSP client.

5. Firewalls

Firewalls exist for the purpose of protecting a network from traffic
not desired by the firewall owner. Therefore Therefore, it is a policy
decision if a firewall will let RTSP and its media streams through or
not. RTSP is designed to be firewall friendly in that it should be
easy to design firewall policies to permit passage of RTSP traffic
and its media streams.

The firewall will need to allow the media streams associated with a an
RTSP session to pass through it. Therefore Therefore, the firewall will need
an ALG that reads RTSP SETUP and TEARDOWN messages. By reading the
SETUP message message, the firewall can determine what type of transport and
from where, where the media stream packets will be sent. Commonly Commonly, there
will be the need to open UDP ports for RTP/RTCP. By looking at the
source and destination addresses and ports ports, the opening in the
firewall can be minimized to the least necessary. The opening in the
firewall can be closed after a TEARDOWN message for that session or
the session itself times out.

The above possibilities for firewalls to inspect and respond to the
signalling
signaling are prevented if end-to-end confidentiality protection is
used for the RTSP signalling, e.g. signaling, e.g., using the specified RTSP over TLS.
This results in that
As a result, firewalls can't be actively opening pinholes for the
media streams based on the signalling. signaling. To enable an RTSP ALG in the
firewall to correctly function function, the hop-by-hop signalling signaling security
(See Section 19.3) in
RTSP 2.0 [I-D.ietf-mmusic-rfc2326bis] can be
used. used (see Section 19.3 of [RTSP]). If not, other
methods have to be used to enable the transport flows for the media.

Simpler firewalls do allow a client to receive media as long as it
has sent packets to the target. Depending on the security level level,
this can have the same behavior as a NAT. The only difference is
that no address translation is done. To use such a firewall firewall, a
client would need to implement one of the above described NAT
traversal methods that include sending packets to the server to open up
create the mappings. necessary filtering state.

6. Comparison of NAT traversal techniques Traversal Techniques

This section evaluates the techniques described above against the
requirements listed in Section 3.

In the following table, the columns correspond to the numbered
requirements. For instance, the column under R1 corresponds to the
first requirement in Section 3: must work for all flavors of NATs.
The rows represent the different NAT/firewall traversal techniques.
Latch is short for Latching, "V. Latch" is short for "variation of
Latching" as described in Section 4.5. 4.5, and "3-W Latch" is short for
the
Three Way Three-Way Latching described in Section 4.6.

A Summary summary of the requirements are:

R1: Work for all flavors of NATs
R2: Must work with firewalls, including those with ALGs

R3: Should have minimal impact on clients not behind NATs, counted in
minimal number of additional RTTs

R4: Should be simple to use, Implement implement, and administer. administer

R5: Should provide mitigation against DDoS attacks

The following considerations are also added to the requirements:

C1: Will the solution support both Clients clients and Servers servers behind NAT NAT?

C2: Is the solution robust to changing as NAT behaviors change?

------------+------+------+------+------+------+------+------+
| R1 | R2 | R3 | R4 | R5 | C1 | C2 |
------------+------+------+------+------+------+------+------+
STUN | No | Yes | 1 | Maybe| No | No | No |
------------+------+------+------+------+------+------+------+
Emb. STUN | Yes | Yes | 2 | Maybe| No | No | Yes |
------------+------+------+------+------+------+------+------+
ICE | Yes | Yes | 2.5 | No | Yes | Yes | Yes |
------------+------+------+------+------+------+------+------+
Latch | Yes | Yes | 1 | Maybe| No | No | Yes |
------------+------+------+------+------+------+------+------+
V. Latch | Yes | Yes | 1 | Yes | No | No | Yes |
------------+------+------+------+------+------+------+------+
3-W Latch | Yes | Yes | 1.5 | Maybe| Yes | No | Yes |
------------+------+------+------+------+------+------+------+
ALG |(Yes) | Yes | 0 | No | Yes | No | Yes |
------------+------+------+------+------+------+------+------+
TCP Tunnel | Yes | Yes | 1.5 | Yes | Yes | No | Yes |
------------+------+------+------+------+------+------+------+
TURN | Yes | Yes | 1 | No | Yes |(Yes) | Yes |
------------+------+------+------+------+------+------+------+

Figure 1: Comparison of fulfillment Fulfillment of requirements Requirements

Looking at Figure 1 1, one would draw the conclusion that using TCP
Tunneling or Three-Way Latching is are the solutions that best fulfill
the requirements. The different techniques were discussed in the
MMUSIC WG. It was established that the WG would pursue an ICE based ICE-based
solution due to its generality and capability of handling also handling
servers delivering media from behind NATs. TCP Tunneling is likely
to be available as an alternative, due to its specification in the
main RTSP specification. Thus Thus, it can be used if desired desired, and the
potential downsides of using TCP is acceptable in particular
deployments. When it comes to Three-Way Latching Latching, it is a very
competitive technique given that you don't need support for RTSP
servers behind NATs. There were was some discussion in the WG about if
the increased implementation burden of ICE is sufficiently motivated
compared to a the Three-Way Latching solution for this generality.
In the end end, the authors believe believed that the reuse of ICE, the greater
flexibility
flexibility, and anyway need any way needed to deploy a new solution was were the
decisive factors.

The ICE based ICE-based RTSP NAT traversal solution is specified in "A Network
Address Translator (NAT) Traversal mechanism for media controlled by
Real-Time Streaming Protocol (RTSP)" [I-D.ietf-mmusic-rtsp-nat]. [RTSP-NAT].

7. IANA Considerations

This document makes no request of IANA.

Note to RFC Editor: this section may be removed on publication as an
RFC.

8. Security Considerations

In the preceding sections sections, we have discussed security merits of the
different NAT/firewall traversal methods for RTSP discussed here. RTSP. In summary, the
presence of NAT(s) is a security risk, as a client cannot perform
source authentication of its IP address. This prevents the
deployment of any future RTSP extensions providing security against
the hijacking of sessions by a man-in-the-middle. man in the middle.

Each of the proposed solutions has security implications. Using STUN
will provide the same level of security as RTSP without transport transport-
level security and source authentications, as long as the server does
not allow media to be sent to a different IP-address IP address than the RTSP
client request was sent from.

Using Latching will have a higher risk of session hijacking or denial
of service DoS
than normal RTSP. The reason is that there exists a probability that
an attacker is able to guess the random bits that the client uses to
prove its identity when creating the address bindings. This can be
solved in the variation of Latching (Section 4.5) with authentication
features. Still Still, both those variants of Latching are vulnerable
against a deliberate attack from the RTSP client to redirect the
media stream requested to any target assuming it can spoof the source
address. This security vulnerability is solved by performing a
Three-way Latching procedure as discussed in Section 4.6.

ICE resolves the binding vulnerability of latching Latching by using signed
STUN messages, as well as requiring that both sides perform
connectivity checks to verify that the target IP address in the
candidate pair is both reachable and willing to respond. ICE can
however can,
however, create a significant amount of traffic if the number of
candidate pairs are large. Thus Thus, pacing is required and
implementations should attempt to limit their number of candidates to
reduce the number of packets.

If the signalling signaling between the ICE peers (RTSP client and Server) server) is
not confidentiality and integrity protected protected, ICE is vulnerable to
attacks where the candidate list is manipulated. Lack The lack of signalling
signaling security will also simplify spoofing of STUN binding
messages by revealing the secret used in signing.

The usage of an RTSP ALG does not in itself increase the risk for
session hijacking. However However, the deployment of ALGs as the sole
mechanism for RTSP NAT traversal will prevent deployment of end-to-
end end-
to-end encrypted RTSP signaling.

The usage of TCP tunneling has no known security problems. However,
it might provide a bottleneck when it comes to end-to-end RTSP
signaling security if TCP tunneling is used on an interleaved RTSP
signaling connection.

The usage of TURN has severe risk of denial of service DoS attacks against a client.
The TURN server can also be used as a redirect point in a DDoS attack
unless the server has strict enough rules for who may create
bindings.

The latching

Since Latching and variant the variants of latching Latching have so such big security issues that
issues, they should not be used at all. The three way latching Three-Way Latching as well
as ICE mitigates these security issues and performs the important
return-routability checks that prevents prevent spoofed source addresses, and
they should be recommended for that reason. RTP ALG's is ALGs are a security
risk as they can create an incitement against using secure RTSP
signalling.
signaling. That can be avoided as ALGs requires require trust in the
middlebox, and that trust becomes explicit if one uses the hop-by-hop
security solution as specified in Section 19.3 of RTSP 2.0.
[I-D.ietf-mmusic-rfc2326bis]. [RTSP].
The remaining methods can be considered safe enough, assuming that
the appropriate security mechanisms are used and not ignored.

9. Acknowledgements

The author would also like to thank all persons on the MMUSIC working
group's mailing list that has commented on this document. Persons
having contributed in such way in no special order to this protocol
are: Jonathan Rosenberg, Philippe Gentric, Tom Marshall, David Yon,
Amir Wolf, Anders Klemets, Flemming Andreasen, Ari Keranen, Bill
Atwood, Alissa Cooper, Colin Perkins, Sarah Banks, David Black and
Alvaro Retana. Thomas Zeng would also like to give special thanks to
Greg Sherwood of PacketVideo for his input into this memo.

Section 1.1 contains text originally written for RFC 4787 by Francois
Audet and Cullen Jennings.

10.

8. Informative References

[I-D.ietf-avt-rtp-no-op]
Andreasen, F., "A No-Op Payload Format for RTP", draft-
ietf-avt-rtp-no-op-04 (work in progress), May 2007.

[I-D.ietf-mmusic-rfc2326bis]
Schulzrinne, H., Rao, A., Lanphier, R., Westerlund, M.,
and M. Stiemerling, "Real Time Streaming Protocol 2.0
(RTSP)", draft-ietf-mmusic-rfc2326bis-40 (work in
progress), February 2014.

[I-D.ietf-mmusic-rtsp-nat]
Goldberg, J., Westerlund, M., and T. Zeng, "A Network
Address Translator (NAT) Traversal Mechanism for Media
Controlled by Real-Time Streaming Protocol (RTSP)", draft-
ietf-mmusic-rtsp-nat-22 (work in progress), July 2014.

[NICE] "Libnice - The Libnice, "The GLib ICE implementation,
http://nice.freedesktop.org/wiki/", May 2013. implementation", June 2015,
<http://nice.freedesktop.org/wiki/>.

[PJNATH] "PJNATH - Open Source ICE, STUN, and TURN Library,
http://www.pjsip.org/pjnath/docs/html/", Library", May 2013.
2013, <http://www.pjsip.org/pjnath/docs/html/>.

[RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768, DOI
10.17487/RFC0768, August 1980. 1980,
<http://www.rfc-editor.org/info/rfc768>.

[RFC0793] Postel, J., "Transmission Control Protocol", STD 7, RFC
793, DOI 10.17487/RFC0793, September 1981. 1981,
<http://www.rfc-editor.org/info/rfc793>.

[RFC2326] Schulzrinne, H., Rao, A., and R. Lanphier, "Real Time
Streaming Protocol (RTSP)", RFC 2326, DOI 10.17487/
RFC2326, April 1998. 1998,
<http://www.rfc-editor.org/info/rfc2326>.

[RFC2588] Finlayson, R., "IP Multicast and Firewalls", RFC 2588, DOI
10.17487/RFC2588, May
1999. 1999,
<http://www.rfc-editor.org/info/rfc2588>.

[RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address
Translator (NAT) Terminology and Considerations", RFC
2663, DOI 10.17487/RFC2663, August 1999. 1999,
<http://www.rfc-editor.org/info/rfc2663>.

[RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP Network
Address Translator (Traditional NAT)", RFC 3022, DOI
10.17487/RFC3022, January
2001. 2001,
<http://www.rfc-editor.org/info/rfc3022>.

[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
DOI 10.17487/RFC3261, June 2002. 2002,
<http://www.rfc-editor.org/info/rfc3261>.

[RFC3424] Daigle, L. L., Ed. and IAB, "IAB Considerations for
UNilateral Self-Address Fixing (UNSAF) Across Network
Address Translation", RFC 3424, DOI 10.17487/RFC3424,
November 2002. 2002, <http://www.rfc-editor.org/info/rfc3424>.

[RFC3489] Rosenberg, J., Weinberger, J., Huitema, C., and R. Mahy,
"STUN - Simple Traversal of User Datagram Protocol (UDP)
Through Network Address Translators (NATs)", RFC 3489, DOI
10.17487/RFC3489, March 2003. 2003,
<http://www.rfc-editor.org/info/rfc3489>.

[RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V.
Jacobson, "RTP: A Transport Protocol for Real-Time
Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550,
July 2003. 2003, <http://www.rfc-editor.org/info/rfc3550>.

[RFC4566] Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
Description Protocol", RFC 4566, DOI 10.17487/RFC4566,
July 2006. 2006, <http://www.rfc-editor.org/info/rfc4566>.

[RFC4571] Lazzaro, J., "Framing Real-time Transport Protocol (RTP)
and RTP Control Protocol (RTCP) Packets over Connection-
Oriented Transport", RFC 4571, DOI 10.17487/RFC4571, July 2006.
2006, <http://www.rfc-editor.org/info/rfc4571>.

[RFC4787] Audet, F. F., Ed. and C. Jennings, "Network Address
Translation (NAT) Behavioral Requirements for Unicast
UDP", BCP 127, RFC 4787, DOI 10.17487/RFC4787, January 2007.
2007, <http://www.rfc-editor.org/info/rfc4787>.

[RFC4961] Wing, D., "Symmetric RTP / RTP Control Protocol (RTCP)",
BCP 131, RFC 4961, DOI 10.17487/RFC4961, July 2007. 2007,
<http://www.rfc-editor.org/info/rfc4961>.

[RFC5245] Rosenberg, J., "Interactive Connectivity Establishment
(ICE): A Protocol for Network Address Translator (NAT)
Traversal for Offer/Answer Protocols", RFC 5245, DOI
10.17487/RFC5245, April
2010. 2010,
<http://www.rfc-editor.org/info/rfc5245>.

[RFC5382] Guha, S., Ed., Biswas, K., Ford, B., Sivakumar, S., and P.
Srisuresh, "NAT Behavioral Requirements for TCP", BCP 142,
RFC 5382, DOI 10.17487/RFC5382, October 2008. 2008,
<http://www.rfc-editor.org/info/rfc5382>.

[RFC5389] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing,
"Session Traversal Utilities for NAT (STUN)", RFC 5389,
DOI 10.17487/RFC5389, October 2008. 2008,
<http://www.rfc-editor.org/info/rfc5389>.

[RFC5764] McGrew, D. and E. Rescorla, "Datagram Transport Layer
Security (DTLS) Extension to Establish Keys for the Secure
Real-time Transport Protocol (SRTP)", RFC 5764, DOI
10.17487/RFC5764, May 2010. 2010,
<http://www.rfc-editor.org/info/rfc5764>.

[RFC5766] Mahy, R., Matthews, P., and J. Rosenberg, "Traversal Using
Relays around NAT (TURN): Relay Extensions to Session
Traversal Utilities for NAT (STUN)", RFC 5766, DOI
10.17487/RFC5766, April 2010. 2010,
<http://www.rfc-editor.org/info/rfc5766>.

[RFC6062] Perreault, S. S., Ed. and J. Rosenberg, "Traversal Using
Relays around NAT (TURN) Extensions for TCP Allocations",
RFC 6062, DOI 10.17487/RFC6062, November 2010. 2010,
<http://www.rfc-editor.org/info/rfc6062>.

[RFC6263] Marjou, X. and A. Sollaud, "Application Mechanism for
Keeping Alive the NAT Mappings Associated with RTP / RTP
Control Protocol (RTCP) Flows", RFC 6263, DOI 10.17487/
RFC6263, June 2011. 2011,
<http://www.rfc-editor.org/info/rfc6263>.

[RFC6275] Perkins, C., Ed., Johnson, D., and J. Arkko, "Mobility
Support in IPv6", RFC 6275, DOI 10.17487/RFC6275, July 2011.
2011, <http://www.rfc-editor.org/info/rfc6275>.

[RFC7362] Ivov, E., Kaplan, H., and D. Wing, "Latching: Hosted NAT
Traversal (HNT) for Media in Real-Time Communication", RFC
7362, DOI 10.17487/RFC7362, September 2014,
<http://www.rfc-editor.org/info/rfc7362>.

[RTP-NO-OP]
Andreasen, F., "A No-Op Payload Format for RTP", Work in
Progress, draft-ietf-avt-rtp-no-op-04, May 2007.

[RTSP] Schulzrinne, H., Rao, A., Lanphier, R., Westerlund, M.,
and M. Stiemerling, "Real Time Streaming Protocol 2.0
(RTSP)", Work in Progress, draft-ietf-mmusic-rfc2326bis-
40, February 2014.

[RTSP-NAT]
Goldberg, J., Westerlund, M., and T. Zeng, "A Network
Address Translator (NAT) Traversal Mechanism for Media
Controlled by Real-Time Streaming Protocol (RTSP)", Work
in Progress, draft-ietf-mmusic-rtsp-nat-22, July 2014.

[STUN-IMPL]
"Open Source STUN Server Client and Client,
http://sourceforge.net/projects/stun/", Server", May 2013. 2013,
<http://sourceforge.net/projects/stun/>.

Acknowledgements

The authors would also like to thank all persons on the MMUSIC
working group's mailing list that have commented on this document.
Persons having contributed to this protocol, in no special order,
are: Jonathan Rosenberg, Philippe Gentric, Tom Marshall, David Yon,
Amir Wolf, Anders Klemets, Flemming Andreasen, Ari Keranen, Bill
Atwood, Alissa Cooper, Colin Perkins, Sarah Banks, David Black, and
Alvaro Retana. Thomas Zeng would also like to give special thanks to
Greg Sherwood of PacketVideo for his input into this memo.

Section 1.1 contains text originally written for RFC 4787 by Francois
Audet and Cullen Jennings.

Authors' Addresses

Magnus Westerlund
Ericsson
Farogatan 6
Stockholm SE-164 80
Sweden

Phone: +46 8 719 0000
Email: magnus.westerlund@ericsson.com

Thomas Zeng
PacketVideo Corp

Email: thomas.zeng@gmail.com