wdiff rfc7610.original rfc7610.txt

opsec
Internet Engineering Task Force (IETF) F. Gont
Internet-Draft
Request for Comments: 7610 SI6 Networks / UTN-FRH
Intended status:
BCP: 199 W. Liu
Category: Best Current Practice W. Liu
Expires: January 7, 2016 Huawei Technologies
ISSN: 2070-1721 G. Van de Velde
Alcatel-Lucent
July 6,
August 2015

DHCPv6-Shield: Protecting Against against Rogue DHCPv6 Servers
draft-ietf-opsec-dhcpv6-shield-08

Abstract

This document specifies a mechanism for protecting hosts connected to
a switched network against rogue DHCPv6 servers. It is based on
DHCPv6 packet-filtering packet filtering at the layer-2 layer 2 device at which the packets
are received. A similar mechanism has been widely deployed in IPv4
networks ('DHCP snooping'), and hence snooping'); hence, it is desirable that similar
functionality be provided for IPv6 networks. This document specifies
a Best Current Practice for the implementation of DHCPv6 Shield. DHCPv6-Shield.

Status of This Memo

This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.

Internet-Drafts are working memo documents an Internet Best Current Practice.

This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
BCPs is available in Section 2 of RFC 5741.

Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on January 7, 2016.
http://www.rfc-editor.org/info/rfc7610.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 ....................................................3
2. Requirements Language . . . . . . . . . . . . . . . . . . . . 3 ...........................................3
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3 .....................................................3
4. DHCPv6-Shield Configuration . . . . . . . . . . . . . . . . . 4 .....................................5
5. DHCPv6-Shield Implementation Requirements . . . . . . . . . . 4 .......................5
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7
7. Security Considerations . . . . . . . . . . . . . . . . . . . 7
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 8
9. .........................................7
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 9
9.1. ......................................................9
7.1. Normative References . . . . . . . . . . . . . . . . . . 9
9.2. .......................................9
7.2. Informative References . . . . . . . . . . . . . . . . . 9 ....................................10
Acknowledgements ..................................................11
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 10 ................................................12

1. Introduction

This document specifies DHCPv6-Shield: DHCPv6-Shield, a mechanism for protecting
hosts connected to a switched network against rogue DHCPv6 servers
[RFC3315]. The basic concept behind DHCPv6-Shield is that a layer-2 layer 2
device filters DHCPv6 messages intended for DHCPv6 clients
(henceforth
(henceforth, "DHCPv6-server messages"), according to a number of
different criteria. The most basic filtering criterion is that
DHCPv6-server messages are discarded by the layer-2 layer 2 device unless
they are received on specific ports of the layer-2 layer 2 device.

Before the DHCPv6-Shield device is deployed, the administrator
specifies the layer-2 layer 2 port(s) on which DHCPv6-server messages are to
be allowed. Only those ports to which a DHCPv6 server or relay is to
be connected should be specified as such. Once deployed, the
DHCPv6-Shield device inspects received packets, packets and allows (i.e. (i.e.,
passes) DHCPv6-server messages only if they are received on layer-2 layer 2
ports that have been explicitly configured for such purpose.

DHCPv6-Shield is analogous to the RA-Guard Router Advertisement Guard (RA-
Guard) mechanism [RFC6104] [RFC6105] [RFC7113], intended for
protection against rogue Router Advertisement [RFC4861] messages.

We note that DHCPv6-Shield mitigates only DHCPv6-based attacks
against hosts. Attack vectors based on other messages meant for
network configuration (such as ICMPv6 Router Advertisements) are not
addressed by DHCPv6-Shield itself. In a similar vein,
DHCPv6-Shielddoes DHCPv6-Shield
does not mitigate attacks against DHCPv6 servers (e.g., Denial of
Service).

2. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].

3. Terminology

DHCPv6-Shield:

the

The set of filtering rules specified in this document, meant to
mitigate attacks that employ DHCPv6-server packets.

DHCPv6-Shield device:

A layer-2 layer 2 device (typically a layer-2 layer 2 switch) that enforces the
filtering policy specified in this document.

For the purposes of this document, the terms "IPv6 Extension Header, Header",
"First Fragment", "IPv6 Header
Chain, First Fragment, Chain", and Upper-layer Header "Upper-Layer Header" are
used as specified in [RFC7112]:

IPv6 Extension Header:

IPv6 Extension Headers are defined in Section 4 of [RFC2460]. As
a result of [RFC7045], [IANA-PROTO] provides a list of assigned
Internet Protocol Numbers and designates which of those protocol
numbers also represent extension headers. IPv6 Extension Headers.

First Fragment:

An IPv6 fragment with fragment offset a Fragment Offset equal to 0.

IPv6 Header Chain:

The header chain IPv6 Header Chain contains an initial IPv6 header, zero or
more IPv6 extension headers, Extension Headers, and optionally, a single upper-layer
header. Upper-Layer
Header. If an upper-layer header Upper-Layer Header is present, it terminates the
header chain; otherwise
IPv6 Header Chain; otherwise, the "No Next Header" value (Next
Header = 59) terminates it.

The first member of the header chain IPv6 Header Chain is always an IPv6
header. For a subsequent header to qualify as a member of the header
chain,
IPv6 Header Chain, it must be referenced by the "Next Header"
field of the previous member of the header chain. IPv6 Header Chain. However,
if a second IPv6 header appears in the header chain, IPv6 Header Chain, as is
the case when IPv6 is tunneled over IPv6, the second IPv6 header
is considered to be an
upper-layer header Upper-Layer Header and terminates the header chain. IPv6
Header Chain. Likewise, if an Encapsulating Security Payload
(ESP) header appears in the
header chain IPv6 Header Chain, it is considered to
be an upper-layer header Upper-Layer Header, and it terminates the header chain.

Upper-layer IPv6 Header Chain.

Upper-Layer Header:

In the general case, the upper-layer header Upper-Layer Header is the first member of
the header chain Header Chain that is neither an IPv6 header nor an IPv6
extension header.
Extension Header. However, if either an ESP header, header or a second
IPv6 header occur occurs in the header chain, they are IPv6 Header Chain, it is considered to
be
upper layer headers an Upper-Layer Header, and they terminate it terminates the header chain. IPv6 Header Chain.

Neither the upper-layer payload, payload nor any protocol data following
the upper-layer payload, payload is considered to be part of the header
chain. IPv6
Header Chain. In a simple example, if the upper-layer header Upper-Layer Header is a
TCP header, the TCP payload is not part of the header chain. IPv6 Header Chain.
In a more complex example, if the upper-layer header Upper-Layer Header is an ESP
header, neither the payload data, data nor any of the fields that follow
the payload data in the ESP header are part of the header chain. IPv6 Header
Chain.

4. DHCPv6-Shield Configuration

Before being deployed for production, the DHCPv6-Shield device is
explicitly configured with respect to which layer-2 layer 2 ports are allowed
to receive DHCPv6 packets destined to DHCPv6 clients (i.e. (i.e.,
DHCPv6-server messages). Only those layer-2 layer 2 ports explicitly
configured for such purpose will be are allowed to receive DHCPv6 packets to
pass to DHCPv6 clients.

5. DHCPv6-Shield Implementation Requirements

The following

Following are the filtering rules that are enforced as part of a
DHCPv6-Shield implementation on those ports that are not allowed to
receive DHCPv6 packets to DHCPv6 clients:

1. DHCPv6-Shield implementations MUST parse the entire IPv6 header
chain Header
Chain present in the packet, packet to identify whether or not it is a
DHCPv6 packet meant for a DHCPv6 client (i.e., a DHCPv6-server
message).

RATIONALE: DHCPv6-Shield implementations MUST NOT enforce a
limit on the number of bytes they can inspect (starting from
the beginning of the IPv6 packet), since this could introduce
false-negatives:
false negatives: DHCP6-server packets received on ports not
allowed to receive such packets could be allowed simply
because the DHCPv6-Shield device does not parse the entire
IPv6 header chain Header Chain present in the packet.

2. When parsing the IPv6 header chain, Header Chain, if the packet is a first-
fragment First
Fragment (i.e., a packet containing a Fragment Header with the
Fragment Offset set to 0) and it fails to contain the entire IPv6
header chain
Header Chain (i.e., all the headers starting from the IPv6 header
up to, and including, the upper-layer header), Upper-Layer Header), DHCPv6-Shield MUST
drop the packet, packet and ought to log the packet drop event in an
implementation-specific manner as a security fault.

RATIONALE: Packets that fail to contain the entire IPv6 header
chain Header
Chain could otherwise be leveraged for circumventing
DHCPv6-Shield. [RFC7112] requires that the first-fragment First Fragment
(i.e., the fragment with the Fragment Offset set to 0)
contains contain
the entire IPv6 header chain, and Header Chain. [RFC7112] also allows
intermediate systems such as routers to drop those packets that fail
to comply with this requirement.

NOTE: This rule should only be applied to IPv6 fragments with
a Fragment Offset of 0 (non-first fragments (non-First Fragments can be safely
passed, since they will never reassemble into a complete
datagram if they are part of a DHCPv6 packet meant for a
DHCPv6 client received on a port where such packets are not
allowed).

3. DHCPv6-Shield MUST provide a configuration knob that controls
whether or not packets with unrecognized Next Header values are
dropped; this configuration knob MUST default to "drop". When
parsing the IPv6 header chain, Header Chain, if the packet contains an
unrecognized Next Header value and the configuration knob is
configured to "drop", DHCPv6-Shield MUST drop the packet, packet and
ought to log the packet drop event in an implementation-specific
manner as a security fault.

RATIONALE: An unrecognized Next Header value could possibly
identify an IPv6 Extension Header, Header and thus be leveraged to
conceal a DHCPv6-server packet (since there is no way for
DHCPv6-Shield to parse past unrecognized Next Header values
[I-D.gont-6man-rfc6564bis]).
[IPV6-UEH]). [RFC7045] requires that nodes be configurable
with respect to whether or not packets with unrecognized
headers are forwarded, forwarded and allows the default behavior to be
that such packets be dropped.

4. When parsing the IPv6 header chain, Header Chain, if the packet is identified
to be a DHCPv6 packet meant for a DHCPv6 client, DHCPv6-Shield
MUST drop the packet, packet and SHOULD log the packet drop event in an
implementation-specific manner as a security alert.

RATIONALE: Ultimately, the goal of DHCPv6-Shield is to drop
DHCPv6 packets destined to DHCPv6 clients (i.e. (i.e., DHCPv6-server
messages) that are received on ports that have not been
explicitly configured to allow the receipt of such packets.

5. In all other cases, DHCPv6-Shield MUST pass the packet as usual.

NOTE: For the purpose of enforcing the DHCPv6-Shield filtering
policy, an ESP header [RFC4303] should be considered to be an
"upper-layer protocol" (that is, it should be considered the last
header in the IPv6 header chain). Header Chain). This means that packets
employing ESP would be passed by the DHCPv6-Shield device to the
intended destination. If the destination host does not have a
security association with the sender of the aforementioned IPv6
packet, the packet would be dropped. Otherwise, if the packet is
considered valid by the IPsec implementation at the receiving host
and encapsulates a DHCPv6 message, it is up to the receiving host what to do with such packet. a packet
is up to the receiving host.

The rules above indicates indicate that if a packet is dropped due to this
filtering policy, the packet drop event should be logged in an
implementation-specific manner as a security fault. It is useful for
the logging mechanism to include a per-port drop counter dedicated to
DHCPv6-Shield packet drops.

In order to protect current end-node IPv6 implementations, Rule #2
has been defined as a such that the default rule to drop is for packets that cannot be
positively identified as not being DHCPv6-server packets (because the
packet is a fragment that fails to include the entire IPv6 header
chain). Header
Chain) to be dropped. This means that, at least in theory,
DHCPv6-Shield could result in false-positive blocking of some
legitimate (non
DHCPv6-server) (non-DHCPv6-server) packets. However, as noted in
[RFC7112], IPv6 packets that fail to include the entire IPv6 header chain Header
Chain are virtually impossible to police with state-less stateless filters and firewalls, and hence
firewalls; hence, they are unlikely to survive in real networks.
[RFC7112] requires that hosts employing fragmentation include the
entire IPv6 header chain Header Chain in the first fragment First Fragment (the fragment with the
Fragment Offset set to 0), thus eliminating the aforementioned false
positives.

The aforementioned filtering rules implicitly handle the case of
fragmented packets: if the DHCPv6-Shield device fails to identify the
upper-layer protocol as a result of the use of fragmentation, the
corresponding packets would be dropped.

Finally, we note that IPv6 implementations that allow overlapping
fragments (i.e. (i.e., that do not comply with [RFC5722]) might still be
subject of DHCPv6-based attacks. However, a recent assessment of
IPv6 implementations [SI6-FRAG] with respect to their fragment
reassembly policy seems to indicate that most current implementations
comply with [RFC5722].

6. IANA Considerations

This document has no actions for IANA.

7. Security Considerations

The recommendations in this document represent the ideal behavior of
a DHCPv6 shield DHCPv6-Shield device. However, in order to implement DHCPv6 shield DHCPv6-Shield
on the fast path, it may be necessary to limit the depth into the
packet that can be scanned before giving up. In circumstances where
there is such a limitation, it is recommended that implementations
drop packets after attempting to find a protocol header up to that
limit, whatever it is. Ideally, such devices should be configurable
with a list of protocol header identifiers so that if new transport
protocols are standardized after the device is released, they can be
added to the list of protocol header types that the device
recognizes. Since any protocol header that is not a UDP header would
be passed by the DHCPv6 shield DHCPv6-Shield algorithm, this would allow such
devices to avoid blocking the use of new transport protocols. When
an implementation must stop searching for recognizable header types
in a packet due to such limitations, whether the device passes SHOULD be
configurable to either pass or drop that packet SHOULD be configurable. packet.

The mechanism specified in this document can be used to mitigate
DHCPv6-based attacks against hosts. Attack vectors based on other
messages meant for network configuration (such as ICMPv6 Router
Advertisements) are out of the scope of this document. Additionally,
the mechanism specified in this document does not mitigate attacks
against DHCPv6 servers (e.g., Denial of Service).

If deployed in layer-2 a layer 2 domain with several cascading switches,
there will be an ingress port on the host's local switch which that will
need to be enabled for receiving DHCPv6-server messages. However,
this local switch will be reliant on the upstream devices to have filtered filtering
out rogue DHCPv6-server messages, as the local switch has no way of
determining which upstream DHCP-server messages are valid.
Therefore, in order to be effective DHCPv6 Shield effective, DHCPv6-Shield should be deployed
and enabled on all layer-2 layer 2 switches of a given layer-2 layer 2 domain.

As noted in Section 5, IPv6 implementations that allow overlapping
fragments (i.e. (i.e., that do not comply with [RFC5722]) might still be
subject of to DHCPv6-based attacks. However, most current
implementations seem to comply with [RFC5722], [RFC5722] and hence forbid IPv6
overlapping fragments.

We note that if an attacker sends a fragmented DHCPv6 packet on a
port not allowed to receive such packets, the first-fragment First Fragment would be
dropped, and the rest of the fragments would be passed. This means
that the victim node would tie memory buffers for the aforementioned
fragments, which would never reassemble into a complete datagram. If
a large number of such packets were sent by an attacker, and the
victim node failed to implement proper resource management for the
fragment reassembly buffer, this could lead to a Denial of Service
(DoS). However, this does not really introduce a new attack vector,
since an attacker could always perform the same attack by sending a
forged fragmented datagram in which at least one of the fragments is
missing. [CPNI-IPv6] discusses some resource management strategies
that could be implemented for the fragment reassembly buffer.

Additionally, we note that the security of a site employing DHCPv6
Shield
DHCPv6-Shield could be further improved by deploying [I-D.ietf-savi-dhcp], [RFC7513] to
mitigate IPv6 address spoofing attacks.

Finally, we note that other mechanisms for mitigating attacks based
on DHCPv6-server messages are available that have different
deployment considerations. For example, [I-D.ietf-dhc-secure-dhcpv6] [SECURE-DHCPV6] allows for
authentication of DHCPv6-server packets if the IPv6 addresses of the
DHCPv6 servers can be pre-configured at the client nodes.

8. Acknowledgements

The authors would like to thank Mike Heard, who provided detailed
feedback on earlier versions of this document and helped a lot

7. References

7.1. Normative References

[RFC2119] Bradner, S., "Key words for use in
producing a technically-sound document throughout the whole
publication process.

The authors would like RFCs to thank (in alphabetical order) Ben Campbell,
Jean-Michel Combes, Sheng Jiang, Ted Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.

[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460,
December 1998, <http://www.rfc-editor.org/info/rfc2460>.

[RFC3315] Droms, R., Ed., Bound, J., Volz, B., Lemon, Pete Resnick, Juergen
Schoenwaelder, Carsten Schmoll, Robert Sleigh, Donald Smith, Mark
Smith, Hannes Tschofenig, Eric Vyncke, and Qin Wu, for providing
valuable comments on earlier versions of this document.

Part of Section 3 of this document was borrowed from [RFC7112],
authored by Fernando Gont, Vishwas Manral, and Ron Bonica.

This document is heavily based on the document [RFC7113] authored by
Fernando Gont. Thus, the authors would like to thank Ran Atkinson,
Karl Auer, Robert Downie, Washam Fan, David Farmer, Mike Heard, Marc
Heuse, Nick Hilliard, Ray Hunter, Joel Jaeggli, Simon Perreault,
Arturo Servin, Gunter van de Velde, James Woodyatt, and Bjoern A.
Zeeb, for providing valuable comments on [RFC7113], on which this
document is based.

The authors would like to thank Joel Jaeggli for his advice and
guidance throughout the IETF process.

9. References

9.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.

[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.

[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C., T., Perkins,
C., and M. Carney, "Dynamic Host Configuration Protocol
for IPv6 (DHCPv6)", RFC 3315, DOI 10.17487/RFC3315, July 2003.
2003, <http://www.rfc-editor.org/info/rfc3315>.

[RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)", RFC
4303, DOI 10.17487/RFC4303, December 2005. 2005,
<http://www.rfc-editor.org/info/rfc4303>.

[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
DOI 10.17487/RFC4861, September 2007. 2007,
<http://www.rfc-editor.org/info/rfc4861>.

[RFC5722] Krishnan, S., "Handling of Overlapping IPv6 Fragments",
RFC 5722, DOI 10.17487/RFC5722, December 2009. 2009,
<http://www.rfc-editor.org/info/rfc5722>.

[RFC7045] Carpenter, B. and S. Jiang, "Transmission and Processing
of IPv6 Extension Headers", RFC 7045,
DOI 10.17487/RFC7045, December 2013,
<http://www.rfc-editor.org/info/rfc7045>.

[RFC7112] Gont, F., Manral, V., and R. Bonica, "Implications of
Oversized IPv6 Header Chains", RFC 7112,
DOI 10.17487/RFC7112, January 2014.

[RFC7045] Carpenter, B. and S. Jiang, "Transmission and Processing
of IPv6 Extension Headers", RFC 7045, December 2013.

9.2. 2014,
<http://www.rfc-editor.org/info/rfc7112>.

7.2. Informative References

[I-D.ietf-dhc-secure-dhcpv6]
Jiang, S. and S. Shen, "Secure DHCPv6 Using CGAs", draft-
ietf-dhc-secure-dhcpv6-07 (work in progress), September
2012.

[I-D.gont-6man-rfc6564bis]

[CPNI-IPv6] Gont, F., "Security Assessment of the Internet Protocol
version 6 (IPv6)", UK Centre for the Protection of
National Infrastructure, (available on request).

[IANA-PROTO] IANA, "Protocol Numbers",
<http://www.iana.org/assignments/protocol-numbers/
protocol-numbers.txt>.

[IPV6-UEH] Gont, F., Will, Liu, W., Krishnan, S., and H. Pfeifer, "IPv6
Universal Extension Header", draft-gont-6man-rfc6564bis-00
(work Work in progress), Progress,
draft-gont- 6man-rfc6564bis-00, April 2014.

[RFC6104] Chown, T. and S. Venaas, "Rogue IPv6 Router
Advertisement Problem Statement", RFC 6104,
DOI 10.17487/RFC6104, February 2011. 2011,
<http://www.rfc-editor.org/info/rfc6104>.

[RFC6105] Levy-Abegnoli, E., Van de Velde, G., Popoviciu, C., and
J. Mohacsi, "IPv6 Router Advertisement Guard", RFC
6105, DOI 10.17487/RFC6105, February 2011. 2011,
<http://www.rfc-editor.org/info/rfc6105>.

[RFC7113] Gont, F., "Implementation Advice for IPv6 Router
Advertisement Guard (RA-Guard)", RFC 7113,
DOI 10.17487/RFC7113, February 2014.

[IANA-PROTO]
Internet Assigned Numbers Authority, "Protocol Numbers",
February 2013, <http://www.iana.org/assignments/protocol-
numbers/protocol-numbers.txt>. 2014,
<http://www.rfc-editor.org/info/rfc7113>.

[RFC7513] Bi, J., Wu, J., Yao, G., and F. Baker, "Source Address
Validation Improvement (SAVI) Solution for DHCP", RFC
7513, DOI 10.17487/RFC7513, May 2015,
<http://www.rfc-editor.org/info/rfc7513>.

[SECURE-DHCPV6]
Jiang, S. and S. Shen, "Secure DHCPv6 Using CGAs", Work
in Progress, draft-ietf-dhc-secure-dhcpv6-07, September
2012.

[SI6-FRAG] SI6 Networks, "IPv6 NIDS evasion and improvements in
IPv6 fragmentation/reassembly", 2012,
<http://blog.si6networks.com/2012/02/
ipv6-nids-evasion-and-improvements-in.html>.

[I-D.ietf-savi-dhcp]
Bi, J., Wu, J., Yao, G.,

Acknowledgements

The authors would like to thank Mike Heard, who provided detailed
feedback on earlier draft versions of this document and F. Baker, "SAVI Solution for
DHCP", draft-ietf-savi-dhcp-34 (work helped a lot
in progress),
February 2015.

[CPNI-IPv6]
Gont, F., "Security Assessment of producing a technically sound document throughout the Internet Protocol
version 6 (IPv6)", UK Centre whole
publication process.

The authors would like to thank (in alphabetical order) Ben Campbell,
Jean-Michel Combes, Sheng Jiang, Ted Lemon, Pete Resnick, Carsten
Schmoll, Juergen Schoenwaelder, Robert Sleigh, Donald Smith, Mark
Smith, Hannes Tschofenig, Eric Vyncke, and Qin Wu for the Protection providing
valuable comments on earlier draft versions of
National Infrastructure, (available this document.

Part of Section 3 of this document was borrowed from [RFC7112],
authored by Fernando Gont, Vishwas Manral, and Ron Bonica.

This document is heavily based on request). [RFC7113], authored by Fernando
Gont. Thus, the authors would like to thank the following
individuals for providing valuable comments on [RFC7113]: Ran
Atkinson, Karl Auer, Robert Downie, Washam Fan, David Farmer, Mike
Heard, Marc Heuse, Nick Hilliard, Ray Hunter, Joel Jaeggli, Simon
Perreault, Arturo Servin, Gunter Van de Velde, James Woodyatt, and
Bjoern A. Zeeb.

The authors would like to thank Joel Jaeggli for his advice and
guidance throughout the IETF process.

Fernando Gont would like to thank Diego Armando Maradona for his
magic and inspiration.

Authors' Addresses

Fernando Gont
SI6 Networks / UTN-FRH
Evaristo Carriego 2644
Haedo, Provincia de Buenos Aires 1706
Argentina

Phone: +54 11 4650 8472
Email: fgont@si6networks.com
URI: http://www.si6networks.com

Will (Shucheng) Liu
Huawei Technologies
Bantian, Longgang District
Shenzhen 518129
P.R.
China

Email: liushucheng@huawei.com

Gunter Van de Velde
Alcatel-Lucent
Copernicuslaan 50
Antwerp, Antwerp 2018
Belgium

Phone: +32 476 476 022
Email: gunter.van_de_velde@alcatel-lucent.com