wdiff rfc8289.original rfc8289.txt

AQM
Internet Engineering Task Force (IETF) K. Nichols
Internet-Draft
Request for Comments: 8289 Pollere, Inc.
Intended status:
Category: Experimental V. Jacobson
Expires: April 16, 2018
ISSN: 2070-1721 A. McGregor, ed. Ed.
J. Iyengar, ed. Ed.
Google
October 13, 2017
January 2018

Controlled Delay Active Queue Management
draft-ietf-aqm-codel-10

Abstract

This document describes a general framework called CoDel (Controlled Delay) -- a general
framework that controls bufferbloat-generated excess delay in modern
networking environments. CoDel consists of an estimator, a setpoint,
and a control loop. It requires no configuration in normal Internet
deployments.

Status of This Memo

This Internet-Draft document is submitted in full conformance with the
provisions of BCP 78 not an Internet Standards Track specification; it is
published for examination, experimental implementation, and BCP 79.

Internet-Drafts are working documents
evaluation.

This document defines an Experimental Protocol for the Internet
community. This document is a product of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF
community. It has received public review and has been approved for
publication by the Internet Engineering Steering Group (IESG). Not
all documents approved by the IESG are a maximum candidate for any level of
Internet Standard; see Section 2 of RFC 7841.

Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on April 16, 2018.
https://www.rfc-editor.org/info/rfc8289.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Conventions and terms used Terms Used in this document This Document . . . . . . . . . 4
3. Understanding the Building Blocks of Queue Management . . . . 5
3.1. Estimator . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2. Target Setpoint . . . . . . . . . . . . . . . . . . . . . 8
3.3. Control Loop . . . . . . . . . . . . . . . . . . . . . . 10 9
4. Overview of the Codel CoDel AQM . . . . . . . . . . . . . . . . . . 12
4.1. Non-starvation . . . . . . . . . . . . . . . . . . . . . 13
4.2. Setting INTERVAL . . . . . . . . . . . . . . . . . . . . 13
4.3. Setting TARGET . . . . . . . . . . . . . . . . . . . . . 14
4.4. Use with multiple queues Multiple Queues . . . . . . . . . . . . . . . . 15
4.5. Setting up Up CoDel . . . . . . . . . . . . . . . . . . . . 15
5. Annotated Pseudo-code Pseudocode for CoDel AQM . . . . . . . . . . . . . 16
5.1. Data Types . . . . . . . . . . . . . . . . . . . . . . . 16
5.2. Per-queue state Per-Queue State (codel_queue_t instance variables) Instance Variables) . . . 17
5.3. Constants . . . . . . . . . . . . . . . . . . . . . . . . 17
5.4. Enqueue routine Routine . . . . . . . . . . . . . . . . . . . . . 17
5.5. Dequeue routine Routine . . . . . . . . . . . . . . . . . . . . . 17
5.6. Helper routines Routines . . . . . . . . . . . . . . . . . . . . . 19
5.7. Implementation considerations Considerations . . . . . . . . . . . . . . 20
6. Further Experimentation . . . . . . . . . . . . . . . . . . . 21
7. Security Considerations . . . . . . . . . . . . . . . . . . . 21
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 21
9. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 21
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.1. 21
9.1. Normative References . . . . . . . . . . . . . . . . . . 22
10.2.
9.2. Informative References . . . . . . . . . . . . . . . . . 22
10.3. URIs . .
Appendix A. Applying CoDel in the Data Center . . . . . . . . . 23
Acknowledgments . . . . . . . . . . . . . . . 23
Appendix A. Applying CoDel in the datacenter . . . . . . . . . . 24
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 25

1. Introduction

The "persistently full buffer" problem has been discussed in the IETF
community since the early 80's [RFC896]. 80s [RFC0896]. The IRTF's End-to-End
Research Group called for the deployment of active queue management Active Queue Management
(AQM) to solve the problem in 1998 [RFC2309]. Despite this
awareness, the problem has only gotten worse as Moore's Law growth in memory
density per Moore's Law fueled an exponential increase in buffer pool
size. Efforts to deploy AQM have been frustrated by difficult
configuration and negative impact on network utilization. This
"bufferbloat" problem [TSV2011] [BB2011] [BLOAT] has become increasingly important
throughout the Internet but particularly at the consumer edge. Queue
management has become more critical due to increased consumer use of
the Internet, mixing large video transactions with time-critical VoIP
and gaming.

An effective AQM remediates bufferbloat at a bottleneck while "doing
no harm" at hops where buffers are not bloated. The However, the
development and deployment of AQM however is are frequently subject to
misconceptions about the cause of packet queues in network buffers.
Network buffers exist to absorb the packet bursts that occur
naturally in statistically multiplexed networks. Buffers helpfully
absorb the queues created by such reasonable packet network behavior such
as short-
term short-term mismatches in traffic arrival and departure rates that
arise from upstream resource contention, transport conversation
startup
transients transients, and/or changes in the number of conversations
sharing a link. Unfortunately, other less useful network behaviors
can cause queues to fill fill, and their effects are not nearly as benign.
Discussion of these issues and the reason why the solution is not
simply smaller buffers "smaller buffers" can be found in [RFC2309], [VANQ2006],
[REDL1998], and [CODEL2012]. To understand queue management, it is
critical to understand the difference between the necessary, useful
"good" queue, queue and the counterproductive "bad" queue.

Several approaches to AQM have been developed over the past two
decades
decades, but none has have been widely deployed due to performance
problems. When designed with the wrong conceptual model for queues,
AQMs have limited operational range, require a lot of configuration
tweaking, and frequently impair rather than improve performance.
Learning from this past history, the CoDel approach is designed to
meet the following goals:

o Making it Make AQM parameterless for normal operation, with no knobs for
operators, users, or implementers to adjust.

o Being Be able to distinguish "good queue" "good" queue from bad "bad" queue and treat
them differently, that is, keep delay low while permitting
necessary bursts of traffic.

o Controlling Control delay while insensitive (or nearly so) to round trip round-trip
delays, link rates rates, and traffic loads; this goal is to "do no
harm" to network traffic while controlling delay.

o Adapting Adapt to dynamically changing link rates with no negative impact
on utilization.

o Allowing Allow simple and efficient implementation (can easily span the
spectrum from low-end access points and home routers up to high-
end router silicon). hardware).

CoDel has five major differences from prior AQMs: use of the local
queue minimum to track congestion ("bad queue"), ("bad" queue), use of an efficient
single state variable representation of that tracked statistic, use
of packet sojourn time as the observed datum, rather datum (rather than packets,
bytes, or rates, rates), use of a mathematically determined setpoint derived
from maximizing network power [KLEIN81], and a modern state space state-space
controller.

CoDel configures itself based on a round-trip time metric which that can be
set to 100ms 100 ms for the normal, terrestrial Internet. With no changes
to parameters, CoDel is expected to work across a wide range of
conditions, with varying links and the full range of terrestrial
round trip
round-trip times.

CoDel is easily adapted to multiple queue systems as shown by [FQ-
CODEL-ID].
[RFC8290]. Implementers and users SHOULD use the fq_codel multiple-
queue approach as it deals with many problems beyond the reach of an
AQM on a single queue.

CoDel was first published in [CODEL2012] and has been implemented in
the Linux kernel.

Note that while this document refers to dropping packets when
indicated by CoDel, it is may be reasonable to ECN-mark packets instead as
well. instead.

2. Conventions and terms used Terms Used in this document This Document

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in [RFC2119].

In this document, these words will appear with that interpretation
BCP 14 [RFC2119] [RFC8174] when, and only when when, they appear in ALL CAPS. Lower case uses of these words are not to be
interpreted all
capitals, as carrying [RFC2119] significance. shown here.

The following terms are defined as used in this document: document and are defined as
follows:

sojourn time: the amount of time a packet has spent in a particular
buffer, i.e. i.e., the time a packet departs the buffer minus the
time the packet arrived at the buffer. A packet can depart a
buffer via transmission or drop.

standing queue: a queue (in packets, bytes, or time delay) in a
buffer that persists for a "long" time time, where "long" is on the
order of the longer round trip round-trip times through the buffer buffer, as
discussed in
section Section 4.2. A standing queue occurs when the
minimum queue over the "long" time is nonzero non-zero and is usually
tolerable and even desirable as long as it does not exceed some
target delay.

bottleneck bandwidth: the limiting bandwidth along a network path.

3. Understanding the Building Blocks of Queue Management

At the heart of queue management is the notion of "good queue" "good" queue and
"bad queue"
"bad" queue and the search for ways to get rid of the bad "bad" queue
(which only adds delay) while preserving the good "good" queue (which
provides for good utilization). This section explains queueing, both
good and bad, and covers the CoDel building blocks that can be used
to manage packet buffers to keep their queues in the "good" range.

Packet queues form in buffers facing bottleneck links, i.e., where
the line rate goes from high to low or where many links converge.
The well-known bandwidth-delay product (sometimes called "pipe size")
is the bottleneck's bandwidth multiplied by the sender-receiver-
sender round-trip delay, and delay; it is the amount of data that has to be in
transit between two hosts in order to run the bottleneck link at 100%
utilization. To explore how queues can form, consider a long-lived
TCP connection with a 25 packet 25-packet window sending through a connection
with a bandwidth-delay product of 20 packets. After an initial burst
of packets packets, the connection will settle into a five packet 5-packet (+/-1)
standing queue; this standing queue size is determined by the
mismatch between the window size and the pipe size, size and is unrelated
to the connection's sending rate. The connection has 25 packets in
flight at all times, but only 20 packets arrive at the destination
over a round trip round-trip time. If the TCP connection has a 30 packet 30-packet
window, the queue will be ten 10 packets with no change in sending rate.
Similarly, if the window is 20 packets, there will be no queue queue, but
the sending rate is the same. Nothing can be inferred about the
sending rate from the queue size, and any queue other than transient
bursts only creates delays in the network. The sender needs to
reduce the number of packets in flight rather than the sending rate.

In the above example, the five packet 5-packet standing queue can be seen to
contribute nothing but delay to the connection, connection and thus is clearly
"bad queue".
"bad" queue. If, in our example, there is a single bottleneck link
and it is much slower than the link that feeds it (say, a high-speed
ethernet
Ethernet link into a limited DSL uplink) uplink), then a 20 packet 20-packet buffer at
the bottleneck might be necessary to temporarily hold the 20 packets
in flight to keep the bottleneck link's utilization high. The burst
of packets should drain completely (to 0 or 1 packets) within a round
trip time
round-trip time, and this transient queue is "good queue" "good" queue because it
allows the connection to keep the 20 packets in flight and for the
bottleneck link to be fully utilized. In terms of the delay
experienced, the "good queue" "good" queue goes away in about a round trip round-trip time,
while "bad queue" "bad" queue hangs around for longer, causing delays.

Effective queue management detects "bad queue" "bad" queue while ignoring "good
queue" "good"
queue and takes action to get rid of the bad "bad" queue when it is
detected. The goal is a queue controller that accomplishes this
objective. To control a queue, we need three basic components components:

o Estimator - To figure out what we've got.

o Target setpoint - To know what we want.

o Control loop - if If what we've got isn't what we want, we need a way
to move it there.

3.1. Estimator

The estimator both observes the queue and detects when good "good" queue
turns to bad "bad" queue and vice versa. CoDel has two parts to its
estimator: what is observed as an indicator of queue and how the
observations are used to detect good/bad "good"/"bad" queue.

Queue length has been widely used as an observed indicator of
congestion and is frequently conflated with sending rate. Use of
queue length as a metric is sensitive to how and when the length is
observed. A high speed high-speed arrival link to a buffer serviced at a much
lower rate can rapidly build up a queue that might disperse
completely or down to a single packet before a round trip round-trip time has
elapsed. If the queue length is monitored at packet arrival (as in
original RED) Random Early Detection (RED)) or departure time, every
packet will see a queue with one possible exception. If the queue
length itself is time sampled (as recommended in [REDL1998], [REDL1998]), a truer
picture of the queue's occupancy can be gained at the expense of
considerable implementation complexity.

The use of queue length is further complicated in networks that are
subject to both short short- and long term long-term changes in available link rate
(as in WiFi). Link rate drops can result in a spike in queue length
that should be ignored unless it persists. It is not the queue
length that should be controlled but the amount of excess delay
packets experience due to a persistent or standing queue, which means
that the packet sojourn time in the buffer is exactly what we want to
track. Tracking the packet sojourn times in the buffer observes the
actual delay experienced by each packet. Sojourn time allows queue
management to be independent of link rate, gives superior performance
to use of buffer size, and is directly related to user-visible
performance. It works regardless of line rate changes or link
sharing by multiple queues (which the individual queues may
experience as changing rates).

Consider a link shared by two queues with different priorities.
Packets that arrive at the high priority high-priority queue are sent as soon as
the link is available available, while packets in the other queue have to wait
until the high priority high-priority queue is empty (i.e., a strict priority
scheduler). The number of packets in the high priority high-priority queue might
be large large, but the queue is emptied quickly quickly, and the amount of time
each packet spends enqueued (the sojourn time) is not large. The
other queue might have a smaller number of packets, but packet
sojourn times will include the waiting time for the high priority high-priority
packets to be sent. This makes the sojourn time a good sample of the
congestion that each separate queue is experiencing. This example
also shows how the metric of sojourn time is independent of the
number of queues or the service discipline used, used and is instead
indicative of congestion seen by the individual queues.

How can observed sojourn time be used to separate good "good" queue from bad
"bad" queue? Although averages, especially of queue length, have
previously been widely used as an indicator of bad "bad" queue, their
efficacy is questionable. Consider the burst that disperses every
round trip
round-trip time. The average queue will be one-half the burst size,
though this might vary depending on when the average is computed and
the timing of arrivals. The average queue sojourn time would be one-
half the time it takes to clear the burst. The average then would
indicate a persistent queue where there is none. Instead of averages
averages, we recommend tracking the minimum sojourn time, time; then, if
there is one packet that has a zero sojourn time then time, there is no
persistent queue.

A persistent queue can be detected by tracking the (local) minimum
queue delay packets experience. To ensure that this minimum value
does not become stale, it has to have been experienced recently, i.e.
i.e., during an appropriate past time interval. This interval is the
maximum amount of time a minimum value is considered to be in effect, effect
and is related to the amount of time it takes for the largest
expected burst to drain. Conservatively, this interval SHOULD be at
least a round trip round-trip time to avoid falsely detecting a persistent queue
and not a lot more than a round trip round-trip time to avoid delay in detecting
the persistent queue. This suggests that the appropriate interval
value is the maximum round-trip time of all the connections sharing
the buffer.

(The

Note that the following key insight makes computation of the local
minimum efficient: It it is sufficient to keep a single state variable of
that indicates how long the minimum has been above or below the
target value rather than retaining all the local values to compute
the minimum, leading which leads to both storage and computational savings.
We use this insight in the
pseudo-code pseudocode for CoDel later in the document.)
document.

These two parts, use of sojourn time as the observed values value and the
local minimum as the statistic to monitor queue congestion congestion, are key
to CoDel's estimator building block. The local minimum sojourn time
provides an accurate and robust measure of standing queue and has an
efficient implementation. In addition, use of the minimum sojourn
time has important advantages in implementation. The minimum packet
sojourn can only be decreased when a packet is dequeued dequeued, which means
that all the work of CoDel can take place when packets are dequeued
for transmission and that no locks are needed in the implementation.
The minimum is the only statistic with this property.

A more detailed explanation with many pictures can be found in
http://www.ietf.org/proceedings/84/slides/slides-84-tsvarea-4.pdf
[1].
[TSV84].

3.2. Target Setpoint

Now that we have a robust way of detecting standing queue, we need a
target setpoint that tells us when to act. If the controller is set
to take action as soon as the estimator has a non-zero value, the
average drop rate will be maximized, which minimizes TCP goodput
[MACTCP1997]. Also, this policy results in no backlog over time (no
persistent queue), which negates much of the value of having a
buffer, since it maximizes the bottleneck link bandwidth lost due to
normal stochastic variation in packet interarrival time. We want a
target that maximizes utilization while minimizing delay. Early in
the history of packet networking, Kleinrock developed the analytic
machinery to do this using a quantity he called 'power', "power", which is the
ratio of a normalized throughput to a normalized delay [KLEIN81].

It is straightforward to derive an analytic expression for the
average goodput of a TCP conversation at a given round-trip time r
and target f (where f is expressed as a fraction of r). Reno TCP,
for example, yields:

goodput = r (3 + 6f - f^2) / (4 (1+f))

Since the peak queue delay is simply the product of f and r, power is
solely a function of f since the r's in the numerator and denominator
cancel:

power is proportional to (1 + 2f - 1/3 f^2) / (1 + f)^2

As Kleinrock observed, the best operating point, in point (in terms of
bandwidth / delay tradeoff,
bandwidth/delay trade-off) is the peak power point, since points off
the peak represent a higher cost (in delay) per unit of bandwidth.
The power vs. f curve for any Additive Increase Multiplicative
Decrease (AIMD) TCP is monotone decreasing. But the curve is very
flat for f < 0.1 0.1, followed by a an increasing curvature with a knee
around f = 0.2, then a steep, almost linear fall off [TSV84]. Since
the previous equation showed that goodput is monotone increasing with
f, the best operating point is near the right edge of the flat top top,
since that represents the highest goodput achievable for a negligible
increase in delay. However, since the r in the model is a
conservative upper bound, a target of 0.1r runs the risk of pushing
shorter RTT connections over the knee and giving them higher delay
for no significant goodput increase. Generally, a more conservative
target of 0.05r offers a good utilization vs. delay tradeoff trade-off while
giving enough headroom to work well with a large variation in real
RTT.

As the above analysis shows, a very small standing queue gives close
to 100% utilization of the bottleneck link. While this result was
for Reno TCP, the derivation uses only properties that must hold for
any 'TCP friendly' "TCP friendly" transport. We have verified by both analysis and
simulation that this result holds for Reno, Cubic, and Westwood
[TSV84]. This results in a particularly simple form for the target:
the ideal range for the permitted standing queue, or the target
setpoint, is between 5% and 10% of the TCP connection's RTT.

We used simulation to explore the impact when TCPs are mixed with
other traffic and with connections of different RTTs. Accordingly,
we experimented extensively with values in the 5-10% of RTT range
and, overall, used target values between 1 and 20 milliseconds for
RTTs from 30 to 500ms 500 ms and link bandwidths of 64Kbps 64 Kbps to 100Mbps 100 Mbps to
experimentally explore a value for the target that gives consistently
high utilization while controlling delay across a range of
bandwidths, RTTs, and traffic loads. Our results were notably
consistent with the mathematics above.

A congested (but not overloaded) CoDel link with traffic composed
solely or primarily of long-lived TCP flows will have a median delay
through the link that will tend to the target. For bursty traffic
loads and for overloaded conditions (where it is difficult or
impossible for all the arriving flows to be accommodated) accommodated), the median
queues will be longer than the target.

The non-starvation drop inhibit feature dominates where the link rate
becomes very small. By inhibiting drops when there is less than an
(outbound link) MTU worth of bytes in the buffer, CoDel adapts to
very low bandwidth links, as shown in [CODEL2012].

3.3. Control Loop

Section 3.1 describes a simple, reliable way to measure bad "bad"
(persistent) queue. Section 3.2 shows that TCP congestion control
dynamics gives rise to a target setpoint for this measure that's a
provably good balance between enhancing throughput and minimizing
delay, and
delay. Section 3.2 also shows that this target is a constant
fraction of the same
'largest "largest average RTT' RTT" interval used to
distinguish persistent from transient queue. The only remaining
building block needed for a basic AQM is a 'control loop' "control loop" algorithm
to effectively drive the queueing system from any 'persistent "persistent queue
above the target' target" state to a state where the persistent queue is
below the target.

Control theory provides a wealth of approaches to the design of
control loops. Most of classical control theory deals with the
control of linear, time-invariant, single-input-single-output Single-Input-Single-Output (SISO)
systems. Control loops for these systems generally come from a (well
understood) well-
understood class known as Proportional-Integral-Derivative (PID)
controllers. Unfortunately, a queue is not a linear system system, and an
AQM operates at the point of maximum non-linearity (where the output
link bandwidth saturates saturates, so increased demand creates delay rather
than higher utilization). Output queues are also not time-invariant time invariant
since traffic is generally a mix of connections which that start and stop
at arbitrary times and which that can have radically different behaviors
ranging from "open loop" "open-loop" UDP audio/video to "closed-loop" congestion-
avoiding TCP. Finally, the constantly changing mix of connections
(which can't be converted to a single 'lumped parameter' "lumped parameter" model
because of their transfer function differences) makes the system
multi-input-multi-output
Multi-Input-Multi-Output (MIMO), not SISO.

Since queueing systems match none of the prerequisites for a
classical controller, a better approach is a modern state-space
controller is a better
approach with states 'no "no persistent queue' queue" and 'has "has persistent
queue'. queue"
states. Since Internet traffic mixtures change rapidly and
unpredictably, a noise noise- and error tolerant error-tolerant adaptation algorithm like
Stochastic Gradient
stochastic gradient is a good choice. Since there's essentially no
information in the amount of persistent queue [TSV84], the adaptation
should be driven by how long it has persisted.

Consider the two extremes of traffic behavior, behavior: a single single, open-loop
UDP video stream and a single, long-lived TCP bulk data transfer. If
the average bandwidth of the UDP video stream is greater that than the
bottleneck link rate, the link's queue will grow grow, and the controller
will eventually enter 'has "has persistent queue' queue" state and start dropping
packets. Since the video stream is open loop, its arrival rate is
unaffected by drops drops, so the queue will persist until the average drop
rate is greater than the output bandwidth deficit (= average arrival
rate - average departure rate) so rate); the job of the adaptation algorithm
is to discover this rate. For this example, the adaptation could
consist of simply estimating the arrival and departure rates and then
dropping at a rate slightly greater than their difference. But difference, but this
class of algorithm won't work at all for the bulk data TCP stream.

TCP runs in closed-loop flow balance [TSV84] [TSV84], so its arrival rate is
almost always exactly equal to the departure rate - -- the queue isn't
the result of a rate imbalance but rather a mismatch between the TCP
sender's window and the source-destination-source round-trip path
capacity (i.e., the connection's bandwidth-delay product). The
sender's TCP congestion avoidance algorithm will slowly increase the
send window (one packet per round-trip-time) [RFC2581] round-trip time) [RFC5681], which will
eventually cause the bottleneck to enter 'has "has persistent queue' queue"
state. But, since the average input rate is the same as the average
output rate, the rate deficit estimation that gave the correct drop
rate for the video stream would compute a drop rate of zero for the
TCP stream. However, if the output link drops one packet as it
enters 'has "has persistent queue' queue" state, when the sender discovers this
(via TCP's normal packet loss repair mechanisms) mechanisms), it will reduce its
window by a factor of two [RFC2581] [RFC5681]; so, one round-trip-time round-trip time after
the drop, the persistent queue will go away.

If there were N TCP conversations sharing the bottleneck, the
controller would have to drop O(N) packets, one packets (one from each
conversation,
conversation) to make all the conversations reduce their window to
get rid of the persistent queue. If the traffic mix consists of
short (<= bandwidth-delay product) conversations, the aggregate
behavior becomes more like the open-loop video example since each
conversation is likely to have already sent all its packets by the
time it learns about a drop so each drop has negligible effect on
subsequent traffic.

The controller does not know the number, duration, or kind of
conversations creating its queue, so it has to learn the appropriate
response. Since single drops can have a large effect if the degree
of multiplexing (the number of active conversations) is small,
dropping at too high a rate is likely to have a catastrophic effect
on throughput. Dropping at a low rate (< 1 packet per round-trip- round-trip
time) and then increasing the drop rate slowly until the persistent
queue goes below the target is unlikely to overdrop and is guaranteed
to eventually dissipate the persistent queue. This stochastic
gradient learning procedure is the core of CoDel's control loop (the
gradient exists because a drop always reduces the (instantaneous) queue
queue, so an increasing drop rate always moves the system "down"
toward no persistent queue, regardless of traffic mix).

The "next drop time" is decreased in inverse proportion to the square
root of the number of drops since the drop state was entered, using
the well-known nonlinear non-linear relationship of drop rate to throughput to
get a linear change in throughput [REDL1998], [MACTCP1997]. [REDL1998][MACTCP1997].

Since the best rate to start dropping is at slightly more than one
packet per RTT, the controller's initial drop rate can be directly
derived from the estimator's interval. When the minimum sojourn time
first crosses the target and CoDel drops a packet, the earliest the
controller could see the effect of the drop is the round trip round-trip time
(interval) + the local queue wait time (the target). If the next
drop happens any earlier than this time (interval + target), CoDel
will overdrop. In practice, the local queue waiting time tends to
vary, so making the initial drop spacing (i.e., the time to the
second drop) be exactly the minimum possible also leads to
overdropping. Analysis of simulation and real-world measured data
shows that the 75th percentile magnitude of this variation is less
than the target, and so the initial drop spacing SHOULD be set to the
estimator's interval (i.e., initial drop spacing = interval) to
ensure that the controller has accounted for acceptable congestion
delays.

Use of the minimum statistic lets the controller be placed in the
dequeue routine with the estimator. This means that the control
signal (the drop) can be sent at the first sign of bad "bad" queue (as
indicated by the sojourn time) and that the controller can stop
acting as soon as the sojourn time falls below the target. Dropping
at dequeue has both implementation and control advantages.

4. Overview of the Codel CoDel AQM

CoDel was initially designed as a bufferbloat solution for the
consumer network edge. The CoDel building blocks are able to adapt
to different or time-varying link rates, to be easily used with multiple
queues, to have excellent utilization with low delay, and to have a simple
and efficient implementation.

The CoDel algorithm described in the rest of this document uses two
key variables: TARGET, which is the controller's target setpoint
described in Section 3.2 3.2, and INTERVAL, which is the estimator's
interval described in Section 3.3.

The only setting CoDel requires is the INTERVAL value, and as 100ms 100 ms
satisfies that definition for normal Internet usage, CoDel can be
parameter-free for consumer use. To ensure that link utilization is
not adversely affected, CoDel's estimator sets TARGET to one that
optimizes power. CoDel's controller does not drop packets when the
drop would leave the queue empty or with fewer than a maximum
transmission unit Maximum
Transmission Unit (MTU) worth of bytes in the buffer. Section 3.2
shows that an ideal TARGET is 5-10% of the connection round trip round-trip time
(RTT). In the open terrestrial-based Internet, especially at the
consumer edge, we expect most unbloated RTTs to have a ceiling of
100ms 100
ms [CHARB2007]. Using this RTT gives a minimum TARGET of 5ms 5 ms and
INTERVAL of 100ms. 100 ms. In practice, uncongested links will see sojourn
times below TARGET more often than once per RTT, so the estimator is
not overly sensitive to the value of INTERVAL.

When the estimator finds a persistent delay above TARGET, the
controller enters the drop state where a packet is dropped dropped, and the
next drop time is set. As discussed in section Section 3.3, the initial next
drop spacing is intended to be long enough to give the endpoints time
to react to the single drop so and therefore SHOULD be set to a value
equal to INTERVAL. If the estimator's output falls below TARGET, the
controller cancels the next drop and exits the drop state. (The
controller is more sensitive than the estimator to an overly short
INTERVAL value, since an unnecessary drop would occur and lower link
utilization.)
utilization). If the next drop time is reached while the controller
is still in drop state, the packet being dequeued is dropped dropped, and the
next drop time is recalculated.

Additional logic prevents re-entering the drop state too soon after
exiting it and resumes the drop state at a recent control level, if
one exists. This logic is described more precisely in the pseudo-
code pseudocode
below. Additional work is required to determine the frequency and
importance of re-entering the drop state.

Note that CoDel AQM only enters its drop state when the local minimum
sojourn delay has exceeded TARGET for a time period long enough for
normal bursts to dissipate, ensuring that a burst of packets that
fits in the pipe will not be dropped.

4.1. Non-starvation

CoDel's goals are to control delay with little or no impact on link
utilization and to be deployed on a wide range of link bandwidths,
including variable-rate links, without reconfiguration. To keep from
making drops when it would starve the output link, CoDel makes
another check before dropping to see if at least an MTU worth of
bytes remains in the buffer. If not, the packet SHOULD NOT be
dropped and,
dropped; therefore, CoDel exits the drop state. The MTU size can be
set adaptively to the largest packet seen so far or can be read from
the interface driver.

4.2. Setting INTERVAL

The INTERVAL value is chosen to give endpoints time to react to a
drop without being so long that response times suffer. CoDel's
estimator, TARGET, and control loop all use INTERVAL. Understanding
their derivation shows that CoDel is the most sensitive to the value
of INTERVAL for single long-lived TCPs with a decreased sensitivity
for traffic mixes. This is fortunate fortunate, as RTTs vary across
connections and are not known a priori. The best policy seems to be
to use an INTERVAL value slightly larger than the RTT seen by most of
the connections using a link, a value that can be determined as the
largest RTT seen if the value is not an outlier (use of a 95-99th
percentile value should work). In practice, this value is not known
or measured (though (however, see section 6.2 Appendix A for an application where
INTERVAL is measured). An INTERVAL setting of 100ms 100 ms works well
across a range of RTTs from 10ms 10 ms to 1 second (excellent performance
is achieved in the range from 10 ms to 300ms). 300 ms). For devices intended
for the normal terrestrial Internet, INTERVAL SHOULD have a value of 100ms.
100 ms. This will only cause overdropping where a long-lived TCP has
an RTT longer than 100ms 100 ms and there is little or no mixing with other
connections through the link.

4.3. Setting TARGET

TARGET is the maximum acceptable persistent queue delay above which
CoDel is dropping or preparing to drop and below which CoDel will not
drop. TARGET SHOULD be set to 5ms 5 ms for normal Internet traffic.

The calculations of section Section 3.2 show that the best TARGET value is
5-10% of the RTT, with the low end of 5% preferred. Extensive
simulations exploring the impact of different TARGET values when used
with mixed traffic flows with different RTTs and different bandwidths
show that below a TARGET of 5ms, 5 ms, utilization suffers for some
conditions and traffic loads, and loads; above 5ms 5 ms showed very little or no
improvement in utilization.

Sojourn times must remain above the TARGET for INTERVAL amount of
time in order to enter the drop state. Any packet with a sojourn
time less than TARGET will reset the time that the queue was last
below TARGET. Since Internet traffic has very dynamic
characteristics, the actual sojourn delay experienced by packets
varies greatly and is often less than TARGET unless the overload is
excessive. When a link is not overloaded, it is not a bottleneck bottleneck,
and packet sojourn times will be small or nonexistent. In the usual
case, there are only one or two places along a path where packets
will encounter a bottleneck (usually at the edge), so the total
amount of queueing delay experienced by a packet should be less than
10ms
10 ms even under extremely congested conditions. This net delay is
substantially lower than common current queueing delays on the
Internet that grow to orders of seconds [NETAL2010, CHARB2007].

A note on [NETAL2010] [CHARB2007].

Regarding the roles of TARGET and the minimum-tracking INTERVAL. INTERVAL, note
that TARGET SHOULD NOT be increased in response to lower layers that
have a bursty nature, where packets are transmitted for short periods
interspersed with idle periods where the link is waiting for
permission to send. CoDel's estimator will "see" the effective
transmission rate over an INTERVAL amount of time, and increasing
TARGET only leads to longer queue delays. On the other hand, where a
significant additional delay is added to the intrinsic RTT of most or
all packets due to the waiting time for a transmission, it is
necessary to increase INTERVAL by that extra delay. TARGET SHOULD
NOT be adjusted for such short-term bursts, but INTERVAL MAY need to
be adjusted if the path's intrinsic RTT changes.

4.4. Use with multiple queues Multiple Queues

CoDel is easily adapted to multiple queue systems. With other
approaches
approaches, there is always a question of how to account for the fact
that each queue receives less than the full link rate over time and
usually sees a varying rate over time. This is what CoDel excels at:
using a packet's sojourn time in the buffer completely circumvents
this problem. In a multiple-queue setting, a separate CoDel
algorithm runs on each queue, but each CoDel instance uses the packet
sojourn time the same way a single-queue CoDel does. Just as a
single-queue CoDel adapts to changing link bandwidths [CODEL2012], so
does a multiple-queue CoDel system. As an optimization to avoid
queueing more than necessary, when testing for queue occupancy before
dropping, the total occupancy of all queues sharing the same output
link SHOULD be used. This property of CoDel has been exploited in
fq_codel [FQ-CODEL-ID], [RFC8290], which hashes on the packet header fields to
determine a specific bin, or sub-queue, for the packet, packet and runs CoDel
on each bin or sub-queue sub-queue, thus creating a well-mixed output flow and
obviating issues of reverse path flows (including "ack compression").

4.5. Setting up Up CoDel

CoDel is set for use in devices in the open Internet. An INTERVAL
setting of 100ms 100 ms is used, TARGET is set to 5% of INTERVAL, and the
initial drop spacing is also set to the INTERVAL. These settings
have been chosen so that a device, such as a small WiFi router, can
be sold without the need for any values to be made adjustable,
yielding a parameterless implementation. In addition, CoDel is
useful in environments with significantly different characteristics
from the normal Internet, for example, in switches used as a cluster
interconnect within a data center. Since cluster traffic is entirely
internal to the data center, round trip round-trip latencies are low (typically
<100us)
<100 us) but bandwidths are high (1-40Gbps) (1-40 Gbps), so it's relatively easy
for the aggregation phase of a distributed computation (e.g., the
Reduce part of a Map/Reduce) to persistently fill and then overflow
the modest per-port buffering available in most high speed high-speed switches.
A CoDel configured for this environment (TARGET and INTERVAL in the
microsecond rather than millisecond range) can minimize drops or ECN
Explicit Congestion Notification (ECN) marks while keeping throughput
high and latency low.

Devices destined for these environments MAY use a different value for
INTERVAL, where suitable. If appropriate analysis indicates, the
TARGET MAY be set to some other value in the 5-10% of INTERVAL INTERVAL, and
the initial drop spacing MAY be set to a value of 1.0 to 1.2 times
INTERVAL. But these settings will cause problems problems, such as
overdropping and low throughput throughput, if used on the open Internet, so
devices that allow CoDel to be configured SHOULD default to Internet-
appropriate the
Internet-appropriate values given in this document.

5. Annotated Pseudo-code Pseudocode for CoDel AQM

What follows is the CoDel algorithm in C++-like pseudo-code. pseudocode. Since
CoDel adds relatively little new code to a basic tail-drop fifo- FIFO
queue, we have attempted to highlight just these additions by
presenting CoDel as a sub-class of a basic fifo-queue FIFO queue base class.
The reference code is included to aid implementers who wish to apply
CoDel to queue management as described here or to adapt its
principles to other applications.

Implementors are strongly encouraged to also look at the Linux kernel
version of CoDel - -- a well-written, well tested, well-tested, real-world, C-based
implementation. As of this writing, it is available at
https://github.com/torvalds/linux/blob/master/net/sched/sch_codel.c.

5.1. Data Types

time_t is an integer time value in units convenient for the system.
The code presented here uses 0 as a flag value to indicate "no time
set."

packet_t* is a pointer to a packet descriptor. We assume it has a
tstamp field capable of holding a time_t and that the field is
available for use by CoDel (it will be set by the enqueue routine and
used by the dequeue routine).

queue_t is a base class for queue objects (the parent class for
codel_queue_t objects). We assume it has enqueue() and dequeue()
methods that can be implemented in child classes. We assume it has a
bytes() method that returns the current queue size in bytes. This
can be an approximate value. The method is invoked in the dequeue()
method but shouldn't require a lock with the enqueue() method.

flag_t is a Boolean.

5.2. Per-queue state Per-Queue State (codel_queue_t instance variables) Instance Variables)

time_t first_above_time_ = 0; // Time to declare sojourn time above
// TARGET
time_t drop_next_ = 0; // Time to drop next packet
uint32_t count_ = 0; // Packets dropped in drop state
uint32_t lastcount_ = 0; // Count from previous iteration
flag_t dropping_ = false; // Set to true if in drop state

5.3. Constants

time_t TARGET = MS2TIME(5); // 5ms 5 ms TARGET queue delay
time_t INTERVAL = MS2TIME(100); // 100ms 100 ms sliding-minimum window
u_int maxpacket = 512; // Maximum packet size in bytes
// (SHOULD use interface MTU)

5.4. Enqueue routine Routine

All the work of CoDel is done in the dequeue routine. The only CoDel
addition to enqueue is putting the current time in the packet's
tstamp field so that the dequeue routine can compute the packet's
sojourn time. Note that packets arriving at a full buffer will be
dropped, but these drops are not counted towards CoDel's
computations.

void codel_queue_t::enqueue(packet_t* pkt)
{
pkt->timestamp()
pkt->tstamp = clock();
queue_t::enqueue(pkt);
}

5.5. Dequeue routine Routine

This is the heart of CoDel. There are two branches based on whether
the controller is in drop state: (i) if the controller is in drop
state (that is, the minimum packet sojourn time is greater than
TARGET)
TARGET), then the controller checks if it is time to leave drop state
or schedules the next drop(s); or (ii) if the controller is not in
drop state, it determines if it should enter drop state and do the
initial drop.

packet_t* CoDelQueue::dequeue()
{
time_t now = clock();
dodequeue_result r = dodequeue(now);
uint32_t delta;

if (dropping_) {
if (! r.ok_to_drop) {
// sojourn time below TARGET - leave drop state
dropping_ = false;
}
// Time for the next drop. Drop current packet and dequeue
// next. If the dequeue doesn't take us out of dropping
// state, schedule the next drop. A large backlog might
// result in drop rates so high that the next drop should
// happen now, hence the 'while' loop.
while (now >= drop_next_ && dropping_) {
drop(r.p);
++count_;
r = dodequeue(now);
if (! r.ok_to_drop) {
// leave drop state
dropping_ = false;
} else {
// schedule the next drop.
drop_next_ = control_law(drop_next_, count_);
}
}
// If we get here here, we're not in drop state. The 'ok_to_drop'
// return from dodequeue means that the sojourn time has been
// above 'TARGET' for 'INTERVAL' 'INTERVAL', so enter drop state.
} else if (r.ok_to_drop) {
drop(r.p);
r = dodequeue(now);
dropping_ = true;

// If min went above TARGET close to when it last went
// below, assume that the drop rate that controlled the
// queue on the last cycle is a good starting point to
// control it now. ('drop_next' will be at most 'INTERVAL'
// later than the time of the last drop drop, so 'now - drop_next'
// is a good approximation of the time from the last drop
// until now.) Implementations vary slightly here; this is
// the Linux version, which is more widely deployed and
// tested.
delta = count_ - lastcount_;
count_ = 1;
if ((delta > 1) && (now - drop_next_ < 16*INTERVAL))
count_ = delta;

drop_next_ = control_law(now, count_);
lastcount_ = count_;
}
return (r.p);
}

5.6. Helper routines Routines

Since the degree of multiplexing and nature of the traffic sources is
unknown, CoDel acts as a closed-loop servo system that gradually
increases the frequency of dropping until the queue is controlled
(sojourn time goes below TARGET). This is the control law that
governs the servo. It has this form because of the sqrt(p)
dependence of TCP throughput on drop probability. Note that for
embedded systems or kernel implementation, the inverse sqrt can be
computed efficiently using only integer multiplication.

time_t codel_queue_t::control_law(time_t t, uint32_t count)
{
return t + INTERVAL / sqrt(count);
}

Next is a helper routine the that does the actual packet dequeue and
tracks whether the sojourn time is above or below TARGET and, if
above, if it has remained above continuously for at least INTERVAL
amount of time. It returns two values: a Boolean indicating if it is
OK to drop (sojourn time above TARGET for at least INTERVAL), INTERVAL) and the
packet dequeued.

typedef struct {
packet_t* p;
flag_t ok_to_drop;
} dodequeue_result;

dodequeue_result codel_queue_t::dodequeue(time_t now)
{
dodequeue_result r = { queue_t::dequeue(), false };
if (r.p == NULL) {
// queue is empty - we can't be above TARGET
first_above_time_ = 0;
return r;
}

// To span a large range of bandwidths, CoDel runs two
// different AQMs in parallel. One is sojourn-time-based based on sojourn time
// and takes effect when the time to send an MTU-sized
// packet is less than TARGET. The 1st term of the "if"
// below does this. The other is backlog-based based on backlog and takes
// effect when the time to send an MTU-sized packet is >=
// TARGET. The goal here is to keep the output link
// utilization high by never allowing the queue to get
// smaller than the amount that arrives in a typical
// interarrival time (MTU-sized packets arriving spaced
// by the amount of time it takes to send such a packet on
// the bottleneck). The 2nd term of the "if" does this.
time_t sojourn_time = now - r.p->tstamp;
if (sojourn_time_ < TARGET || bytes() <= maxpacket_) {
// went below - stay below for at least INTERVAL
first_above_time_ = 0;
} else {
if (first_above_time_ == 0) {
// just went above from below. if still above at
// first_above_time, will say it's ok to drop.
first_above_time_ = now + INTERVAL;
} else if (now >= first_above_time_) {
r.ok_to_drop = true;
}
}
return r;
}

5.7. Implementation considerations Considerations

time_t is an integer time value in units convenient for the system.
Resolution to at least a millisecond is required required, and better
resolution is useful up to the minimum possible packet time on the
output link; 64- or 32-bit widths are acceptable but with 32 bits the
resolution should be no finer than 2^{-16} to leave enough dynamic
range to represent a wide range of queue waiting times. Narrower
widths also have implementation issues due to overflow (wrapping) and
underflow (limit cycles because of truncation to zero) that are not
addressed in this pseudocode.

Since CoDel requires relatively little per-queue state and no direct
communication or state sharing between the enqueue and dequeue
routines, it is relatively simple to add CoDel to almost any packet
processing pipeline, including ASIC- or NPU-based forwarding engines. engines based on
Application-Specific Integrated Circuits (ASICs) or Network
Processors (NPUs). One issue to consider is dodequeue()'s use of a
'bytes()' function to determine the current queue size in bytes.
This value does not need to be exact. If the enqueue part of the
pipeline keeps a running count of the total number of bytes it has
put into the queue queue, and the dequeue routine keeps a running count of
the total bytes it has removed from the queue, 'bytes()' is simply
the difference between these two counters (32-bit counters should be adequate.)
adequate). Enqueue has to update its counter once per packet queued queued,
but it does not matter when (before, during during, or after the packet has
been added to the queue). The worst that can happen is a slight, transient,
transient underestimate of the queue size size, which might cause a drop
to be briefly deferred.

6. Further Experimentation

We encourage experimentation with the recommended values of TARGET
and INTERVAL for Internet settings. CoDel provides general,
efficient, parameterless building blocks for queue management that
can be applied to single or multiple queues in a variety of data
networking scenarios. CoDel's settings may be modified for other
special-purpose networking applications.

7. Security Considerations

This document describes an active queue management algorithm for
implementation in networked devices. There are no known security
exposures associated with CoDel at this time.

8. IANA Considerations

This document does not require actions by IANA.

9. Acknowledgments

The authors thank Jim Gettys for the constructive nagging that made
us get the work "out there" before we thought it was ready. We thank
Dave Taht, Eric Dumazet, and the open source community for showing
the value of getting it "out there" and for making it real. We thank
Nandita Dukkipati for contributions to section 6 and for comments
which helped to substantially improve this draft. We thank the AQM
working group and the Transport Area shepherd, Wes Eddy, for
patiently prodding this draft all the way to a standard.

10. References

10.1.

9.1. Normative References

[RFC2119] Bradner, S., "Key Words words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997.

10.2. 1997,
<https://www.rfc-editor.org/info/rfc2119>.

[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.

9.2. Informative References

[BB2011]

[BLOAT] Gettys, J. and K. Nichols, "Bufferbloat: Dark Buffers in
the Internet", Communications of the ACM 9(11) pp. 57-65.

[BMPFQ] Suter, B., "Buffer Management Schemes for Supporting TCP
in Gigabit Routers with Per-flow Queueing", IEEE Journal
on Selected Areas in Communications Vol. 17 ACM, Volume 55, Issue 6, June,
1999, pp. 1159-1169.
1, DOI 10.1145/2063176.2063196, January 2012.

[CHARB2007]
Dischinger, M., Haeberlen, A., Gummadi, K., and S. Saroiu,
"Characterizing Residential Broadband Networks",
Proceedings of the Internet Measurement 7th ACM SIGCOMM Conference San Diego, CA, on Internet
Measurement, DOI 10.1145/1298306.1298313, October 2007.

[CODEL2012]
Nichols, K. and V. Jacobson, "Controlling Queue Delay",
Communications of the
ACM Vol. 55 No. 11, July, 2012, pp.
42-50.

[FQ-CODEL-ID]
Hoeiland-Joergensen, T., McKenney, P.,
dave.taht@gmail.com, d., Gettys, J., and E. Dumazet,
"FlowQueue-Codel", draft-ietf-aqm-fq-codel-06 (work in
progress), March 2017. Queue, Volume 10, Issue 5,
DOI 10.1145/2208917.2209336, May 2012.

[KLEIN81] Kleinrock, L. and R. Gail, "An Invariant Property of
Computer Network Power", Proceedings of the International
Conference on
Communications June, Communications, June 1981,
<http://www.lk.cs.ucla.edu/data/files/Gail/power.pdf>.

[MACTCP1997]
Mathis, M., Semke, J., and J. Mahdavi, J., and T. Ott, "The
Macroscopic Behavior of the TCP Congestion Avoidance
Algorithm", ACM SIGCOMM Computer Communications Review Vol. 27 no. 1, Jan.
2007.
Review, Volume 27, Issue 3, pp. 67-82,
DOI 10.1145/263932.264023, July 1997.

[NETAL2010]
Kreibich, C., Weaver, N., Paxson, V., and B. Nechaev,
"Netalyzr: Illuminating the Edge Network", Proceedings of
the Internet Measurement 10th ACM SIGCOMM Conference Melbourne, Australia, on Internet Measurement,
DOI 10.1145/1879141.1879173, November 2010.

[REDL1998]
Nichols, K., Jacobson, V., and K. Poduri, "RED in a
Different Light", Tech report, September, Technical Report, Cisco Systems,
September 1999,
<http://www.cnaf.infn.it/~ferrari/papers/ispn/
red_light_9_30.pdf>. <http://citeseerx.ist.psu.edu/viewdoc/
summary?doi=10.1.1.22.9406>.

[RFC0896] Nagle, J., "Congestion Control in IP/TCP Internetworks",
RFC 896, DOI 10.17487/RFC0896, January 1984,
<https://www.rfc-editor.org/info/rfc896>.

[RFC2309] Braden, B., Clark, D., Crowcroft, J., Davie, B., Deering,
S., Estrin, D., Floyd, S., Jacobson, V., Minshall, G.,
Partridge, C., Peterson, L., Ramakrishnan, K., Shenker,
S., Wroclawski, J., and L. Zhang, "Recommendations on
Queue Management and Congestion Avoidance in the
Internet", RFC 2309, DOI 10.17487/RFC2309, April 1998.

[RFC2581] 1998,
<https://www.rfc-editor.org/info/rfc2309>.

[RFC5681] Allman, M., Paxson, V., and W. Stevens, E. Blanton, "TCP Congestion
Control", RFC 2581, April 1999.

[RFC896] Nagle, J., "Congestion control in IP/TCP internetworks",
RFC 896, January 1984.

[SFQ1990] 5681, DOI 10.17487/RFC5681, September 2009,
<https://www.rfc-editor.org/info/rfc5681>.

[RFC8290] Hoeiland-Joergensen, T., McKenney, P., "Stochastic Fairness Queuing", Proceedings
of IEEE INFOCOMM 90 San Francisco, 1990.

[TSV2011] Taht, D., Gettys,
J., "Bufferbloat: Dark Buffers in the Internet", and E. Dumazet, "The FlowQueue-CoDel Packet Scheduler
and Active Queue Management Algorithm", RFC 8290,
DOI 10.17487/RFC8290, December 2017,
<https://www.rfc-editor.org/info/rfc8290>.

[TSV84] Jacobson, V., "CoDel", IETF 80 presentation to 84, Transport Area Open
Meeting,
March, 2011,
<http://www.ietf.org/proceedings/80/tsvarea.html>.

[TSV84] Jacobson, V., "CoDel talk at TSV meeting IETF 84", July 2012,
<http://www.ietf.org/proceedings/84/slides/
slides-84-tsvarea-4.pdf>.

[VANQ2006]
Jacobson, V., "A Rant on Queues", talk Talk at MIT Lincoln
Labs, Lexington, MA July, MA, July 2006,
<http://www.pollere.net/Pdfdocs/QrantJul06.pdf>.

10.3. URIs

[1] http://www.ietf.org/proceedings/84/slides/slides-84-tsvarea-4.pdf

Appendix A. Applying CoDel in the datacenter Data Center

Nandita Dukkipati and her group at Google realized that the CoDel
building blocks could be applied to bufferbloat problems in
datacenter data-
center servers, not just to Internet routers. The Linux CoDel
queueing discipline (qdisc) was adapted in three ways to tackle this
bufferbloat problem.

1. The default CoDel action was modified to be a direct feedback
from qdisc to the TCP layer at dequeue. The direct feedback
simply reduces TCP's congestion window just as congestion control
would do in the event of drop. The scheme falls back to ECN
marking or packet drop if the TCP socket lock could not be
acquired at dequeue.

2. Being located in the server makes it possible to monitor the
actual RTT to use as CoDel's interval rather than making a "best
guess" of RTT. The CoDel interval is dynamically adjusted by
using the maximum TCP round-trip time (RTT) of those connections
sharing the same Qdisc/bucket. qdisc/bucket. In particular, there is a history
entry of the maximum RTT experienced over the last second. As a
packet is dequeued, the RTT estimate is accessed from its TCP
socket. If the estimate is larger than the current CoDel
interval, the CoDel interval is immediately refreshed to the new
value. If the CoDel interval is not refreshed for over a second,
it is decreased it to the history entry entry, and the process is
repeated. The use of the dynamic TCP RTT estimate lets allows the
interval to adapt to the actual maximum value currently seen and
thus lets the controller space its drop intervals appropriately.

3. Since the mathematics of computing the setpoint are invariant, a
target
TARGET of 5% of the RTT or CoDel interval was used here.

Non-data packets were not dropped dropped, as these are typically small and
sometimes critical control packets. Being located on the server,
there is no concern with misbehaving users as there would be on the
public Internet.

In several data center data-center workload benchmarks, which are typically
bursty, CoDel reduced the queueing latencies at the qdisc, qdisc and thereby
improved the mean and 99th-percentile latencies from several tens of
milliseconds to less than one millisecond. The minimum tracking part
of the CoDel framework proved useful in disambiguating "good" queue
versus "bad" queue, which is particularly helpful in controlling
qdisc buffers that are inherently bursty because of TCP Segmentation
Offload (TSO).

Acknowledgments

The authors thank Jim Gettys for the constructive nagging that made
us get the work "out there" before we thought it was ready. We thank
Dave Taht, Eric Dumazet, and the open source community for showing
the value of getting it "out there" and for making it real. We thank
Nandita Dukkipati for contributions to Section 6 and for comments
that helped to substantially improve this document. We thank the AQM
Working Group and the Transport Area Shepherd, Wes Eddy, for
patiently prodding this document all the way to publication as an
RFC.

Authors' Addresses

Kathleen Nichols
Pollere, Inc.
PO Box 370201
Montara, CA 94037
USA
United States of America

Email: nichols@pollere.com

Van Jacobson
Google

Email: vanj@google.com

Andrew McGregor (editor)
Google

Email: andrewmcgr@google.com

Janardhan Iyengar (editor)
Google

Email: jri@google.com