wdiff rfc8335.original rfc8335.txt

INTAREA
Internet Engineering Task Force (IETF) R. Bonica
Internet-Draft
Request for Comments: 8335 R. Thomas
Updates: 4884 (if approved) Juniper Networks
Intended status:
Category: Standards Track J. Linkova
Expires: June 18, 2018
ISSN: 2070-1721 Google
C. Lenart
Verizon
M. Boucadair
Orange
December 15, 2017
February 2018

PROBE: A Utility For for Probing Interfaces
draft-ietf-intarea-probe-10

Abstract

This document describes a network diagnostic tool called PROBE.
PROBE is similar to PING, PING in that it can be used to query the status
of a probed interface. It interface, but it differs from PING in that it does not
require bidirectional connectivity between the probing and probed
interfaces. Instead, PROBE requires bidirectional connectivity
between the probing interface and a proxy interface. The proxy
interface can reside on the same node as the probed interface interface, or it
can reside on a node to which the probed interface is directly
connected. This document updates RFC 4884.

Status of This Memo

This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents an Internet Standards Track document.

This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.

Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on June 18, 2018.
https://www.rfc-editor.org/info/rfc8335.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 4
1.2. Requirements Language . . . . . . . . . . . . . . . . . . 4
2. ICMP Extended Echo Request . . . . . . . . . . . . . . . . . 4
2.1. Interface Identification Object . . . . . . . . . . . . . 6
3. ICMP Extended Echo Reply . . . . . . . . . . . . . . . . . . 7
4. ICMP Message Processing . . . . . . . . . . . . . . . . . . . 9
4.1. Code Field Processing . . . . . . . . . . . . . . . . . . 10
5. Use-Cases Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Updates to RFC 4884 . . . . . . . . . . . . . . . . . . . . . 12
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12
8. Security Considerations . . . . . . . . . . . . . . . . . . . 13
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 14
9.1. Normative References . . . . . . . . . . . . . . . . . . 14
9.2. Informative References . . . . . . . . . . . . . . . . . 15
Appendix A. The PROBE Application . . . . . . . . . . . . . . . 15 16
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 16 17
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 16 17

1. Introduction

Network operators use PING [RFC2151] to test bidirectional
connectivity between two interfaces. For the purposes of this
document, we will call these interfaces are called the probing and probed
interfaces. PING sends an ICMP [RFC0792] [RFC4443] Echo Request
message from the probing interface to the probed interface. The
probing interface resides on a probing node while the probed
interface resides on a probed node.

If the probed interface receives the ICMP Echo Request message, it
returns an ICMP Echo Reply. When the probing interface receives the
ICMP Echo Reply, it has verified bidirectional connectivity between
the probing and probed interfaces. Specifically, it has verified
that:

o The probing node can reach the probed interface interface.

o The probed interface is active active.

o The probed node can reach the probing interface interface.

o The probing interface is active active.

Like PING, PROBE executes on a probing node. It sends an ICMP
Extended Echo Request message from a local interface, called the
probing interface, to a proxy interface. The proxy interface resides
on a proxy node.

The ICMP Extended Echo Request contains an ICMP Extension Structure
and the ICMP Extension Structure contains an Interface Identification
Object. The Interface Identification Object identifies the probed
interface. The probed interface can reside on the proxy node or it
can be directly connected connect to
the proxy node.

When the proxy interface receives the ICMP Extended Echo Request, the
proxy node executes access control procedures. If access is granted,
the proxy node determines the status of the probed interface and
returns an ICMP Extended Echo Reply Message. message. The ICMP Extended Echo
Reply indicates the status of the probed interface.

If the probed interface resides on the proxy node, PROBE determines
the status of the probed interface as it would determine its oper-
status [RFC7223]. If oper-status is equal to up 'up' (1), PROBE reports
that the probed interface is active. Otherwise, PROBE reports that
the probed interface is inactive.

If the probed interface resides on a node that is directly connected
to the probed proxy node, and the probed interface appears in the IPv4
Address Resolution Protocol (ARP) table [RFC0826] or IPv6 Neighbor
Cache [RFC4861], PROBE reports interface reachability. Otherwise,
PROBE reports that the table entry does not exist.

1.1. Terminology

This document uses the following terms:

o Probing interface - interface: The interface that sends the ICMP Extended Echo Request
Request.

o Probing node - node: The node upon which the probing interface resides resides.

o Proxy interface - interface: The interface to which the ICMP Extended Echo
Request message is sent sent.

o Proxy node - node: The node upon which the proxy interface resides resides.

o Probed interface - interface: The interface whose status is being queried queried.

o Probed node - node: The node upon which the probed interface resides. If
the proxy interface and the probed interface reside upon the same
node, the proxy node is also the probed node. Otherwise, the
proxy node is directly connected to the probed node.

1.2. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.

2. ICMP Extended Echo Request

The ICMP Extended Echo Request message is defined for both ICMPv4 and
ICMPv6. Like any ICMP message, the ICMP Extended Echo Request
message is encapsulated in an IP header. The ICMPv4 version of the
Extended Echo Request message is encapsulated in an IPv4 header,
while the ICMPv6 version is encapsulated in an IPv6 header.

Figure 1 depicts the ICMP Extended Echo Request message.

Figure 1: ICMP Extended Echo Request Message

IP Header fields:

o Source Address: The Source Address identifies the probing
interface. It MUST be a valid IPv4 or IPv6 unicast address.

o Destination Address: The Destination Address identifies the proxy
interface. It can MUST be a unicast, multicast or anycast unicast address.

ICMP fields:

o Type: Extended Echo Request. The value for ICMPv4 is TTT0. <RFC
Editor: Please replace TTT0 with the ICMPv4 type number for
Extended Echo Request>. 42. The
value for ICMPv6 is TTT1. <RFC
Editor: Please replace TTT1 with the ICMPv6 type number for
Extended Echo Request> . 160.

o Code: MUST be set to 0 and MUST be ignored upon receipt.

o Checksum: For ICMPv4, see RFC 792. For ICMPv6, see RFC 4443.

o Identifier: An identifier Identifier to aid in matching Extended Echo Replies
to Extended Echo Requests. May be zero. 0.

o Sequence Number: A sequence number Sequence Number to aid in matching Extended
Echo Replies to Extended Echo Requests. May be zero. 0.

o Reserved: This field MUST be set to zero 0 and ignored upon receipt.

o L (local) - (local): The L-bit is set if the probed interface resides on the
proxy node. The L-bit is clear if the probed interface is
directly connected to the proxy node.

o ICMP Extension Structure: The ICMP Extension Structure identifies
the probed interface.

Section 7 of [RFC4884] defines the ICMP Extension Structure. As per
RFC 4884, the Extension Structure contains exactly one Extension
Header followed by one or more objects. When applied to the ICMP
Extended Echo Request message, the ICMP Extension Structure MUST
contain exactly one instance of the Interface Identification Object
(Section
(see Section 2.1).

If the L-bit is set, the Interface Identification Object can identify
the probed interface by name, index index, or address. It If the L-bit is
clear, the Interface Identification Object MUST identify the probed
interface by address.

If the Interface Identification Object identifies the probed
interface by address, that address can be a member of any address
family. For example, an ICMPv4 Extended Echo Request message can
carry an Interface Identification Object that identifies the probed
interface by IPv4, IPv6 IPv6, or IEEE 802 address. Likewise, an ICMPv6
Extended Echo Request message can carry an Interface Identification
Object that identifies the probed interface by IPv4, IPv6 IPv6, or IEEE
802 address.

2.1. Interface Identification Object

The Interface Identification Object identifies the probed interface
by name, index, or address. Like any other ICMP Extension Object, it
contains an Object Header and Object Payload. The Object Header
contains the following fields:

o Class-Num: Interface Identification Object. Value The value is TTT2. <RFC
Editor: Please replace TTT2 with the Class-Num for the Interface
Identification Object> 3.

o C-type: C-Type: Values are: are (1) Identifies Interface By by Name, (2)
Identifies Interface By by Index, and (3) Identifies Interface By
Address by
Address.

o Length: Length of the object, measured in octets, including the
object header
Object Header and object payload. Object Payload.

If the Interface Identification Object identifies the probed
interface by name, the object payload Object Payload MUST be the interface name as
defined in [RFC7223]. If the object payload Object Payload would not otherwise
terminate on a 32-bit boundary, it MUST be padded with ASCII NULL
characters.

If the Interface Identification Object identifies the probed
interface by index, the length is equal to 8 and the payload contains
the if-index [RFC7223].

If the Interface Identification Object identifies the probed
interface by address, the payload is as depicted in Figure 2.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| AFI | Address Length| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address ....

Figure 2: Interface Identification Object - C-type C-Type 3 Payload

Payload fields are defined as follows:

o Address Family Identifier (AFI): This 16-bit field identifies the
type of address represented by the Address field. All values
found in the IANA registry of Address Family Numbers (available
from <https://www.iana.org/assignments/address-family-numbers/
address-family-numbers.xhtml>) <https://www.iana.org/assignments/address-family-numbers>)
are valid in this field.

o Address Length - Length: Number of significant bytes contained by the
Address field. (The address Address field contains significant bytes and
padding bytes) bytes.)

o Reserved: This field MUST be set to zero 0 and ignored upon receipt.

o Address: This variable-length field represents an address
associated with the probed interface. If the address field would
not otherwise terminate on a 32-bit boundary, it MUST be padded
with zeros. zeroes.

3. ICMP Extended Echo Reply

The ICMP Extended Echo Reply message is defined for both ICMPv4 and
ICMPv6. Like any ICMP message, the ICMP Extended Echo Reply message
is encapsulated in an IP header. The ICMPv4 version of the Extended
Echo Reply message is encapsulated in an IPv4 header, while the
ICMPv6 version is encapsulated in an IPv6 header.

Figure 3 depicts the ICMP Extended Echo Reply message.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Identifier |Sequence Number|State|Res|A|4|6|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Figure 3: ICMP Extened Extended Echo Reply Message
IP Header fields:

o Source address: Address: Copied from the Destination Address field of the
invoking Extended Echo Request message message.

o Destination address: Address: Copied from the Source Address field of the
invoking Extended Echo Request message message.

ICMP fields:

o Type: Extended Echo Reply. The value for ICMPv4 is TTT3. <RFC
Editor: Please replace TTT3 with the ICMPv4 type number for
Extended Echo Reply>. 43. The value
for ICMPv6 is TTT4. <RFC Editor:
Please replace TTT4 with the ICMPv6 type number for Extended Echo
Reply>. 161.

o Code: Values are (0) No Error, (1) Malformed Query, (2) No Such
Interface, (3) No Such Table Entry, and (4) Multiple Interfaces
Satisfy Query Query.

o Checksum: For ICMPv4, see RFC 792. For ICMPv6, see RFC 4443 4443.

o Identifier: Copied from the Identifier field of the invoking
Extended Echo Request packet packet.

o Sequence Number: Copied from the Sequence Number field of the
invoking Extended Echo Request packet packet.

o State - State: If Code is not equal to 0, this field MUST be set to 0 and
ignored upon receipt. Likewise, if the probed interface resides
upon the proxy node, this field MUST be set to 0 and ignored upon
receipt. Otherwise, this field reflects the state of the ARP
Table
table or Neighbor Cache entry associated with the probed
interface. Values are (0) Reserved Reserved, (1) Incomplete Incomplete, (2) Reachable
Reachable, (3) Stale Stale, (4) Delay Delay, (5) Probe Probe, and (6) Failed Failed.

o Res - Res: This field MUST be set to 0 and ignored upon receipt.

o A (Active) - (Active): The A-bit is set if the Code is equal to zero, 0, the probed
interface resides on the proxy node, and the probed interface is
active. Otherwise, the A-bit is clear.

o 4 (IPv4) - (IPv4): The 4-bit is set if the A-bit is also set and IPv4 is
running on the probed interface. Otherwise, the 4-bit is clear.

o 6 (IPv6) - (IPv6): The 6-bit is set if the A-bit is also set and IPv6 is
running on the probed interface. Otherwise, the 6-bit is clear.

4. ICMP Message Processing

When a node receives an ICMP Extended Echo Request message and any of
the following conditions apply, the node MUST silently discard the
incoming message:

o The node does not recognize ICMP Extended Echo Request messages messages.

o The node has not explicitly enabled ICMP Extended Echo
functionality
functionality.

o The incoming ICMP Extend Echo Request carries a source address Source Address
that is not explicitly authorized for the L-bit setting of the
incoming ICMP Extended Echo Request L-bit setting Request.

o The incoming ICMP Extend Echo Request carries a source address Source Address
that is not explicitly authorized for the incoming ICMP Extended
Echo Request type (i.e., by ifName, by IfIndex, or by Address) Address).

o The Source Address of the incoming messages message is not a unicast
address
address.

o The Destination Address of the incoming message is a multicast
address.

Otherwise, when a node receives an ICMPv4 Extended Echo Request, it
MUST format an ICMP Extended Echo Reply as follows:

o Don't Fragment flag (DF) flag is 1

o More Fragments flag is 0

o Fragment Offset is 0

o TTL is 255

o Protocol is ICMP

When a node receives an ICMPv6 Extended Echo Request, it MUST format
an ICMPv6 Extended Echo Reply as follows:

o Hop Limit is 255

o Next Header is ICMPv6

In either case, the responding node MUST: MUST do the following:

o Copy the source address Source Address from the Extended Echo Request message to
the destination address Destination Address of the Extended Echo Reply Reply.

o Copy the destination address Destination Address from the Extended Echo Request
message to the source address Source Address of the Extended Echo Reply Reply.

o Set the DiffServ codepoint to CS0 [RFC4594] [RFC4594].

o Set the ICMP Type to Extended Echo Reply Reply.

o Copy the Identifier from the Extended Echo Request message to the
Extended Echo Reply Reply.

o Copy the Sequence Number from the Extended Echo Request message to
the Extended Echo Reply Reply.

o Set the Code field as described in Section 4.1 4.1.

o Set the State field to 0.

o Clear the A-bit, the 4-bit 4-bit, and the 6-bit.

o If (1) the Code Field is equal to (0) No Error and Error, (2) the L-bit is set
set, and (3) the probed interface is active, set the A-bit. Also Also,
set the 4-bit and the 6-bit as appropriate.

o If the Code Field field is equal to (0) No Error and the L-bit is clear,
then set the State field to reflect the state of the ARP Table table or
Neighbor Cache entry that represents the probed interface.

o Set the checksum appropriately Checksum appropriately.

o Forward the ICMP Extended Echo Reply to its destination destination.

4.1. Code Field Processing

The Code field MUST be set to (1) Malformed Query if any of the
following conditions apply:

o The ICMP Extended Echo Request does not include an ICMP Extension
Structure
Structure.

o The ICMP Extension Structure does not include exactly one
Interface Identification Object Object.

o The L-bit is clear and the Interface Identification Object
identifies the probed interface by ifName or ifIndex ifIndex.

o The query is otherwise malformed malformed.

The Code field MUST be set to (2) No Such Interface if the L-bit is
set and the ICMP Extension Structure does not identify an interface
that resides on the proxy node.

The Code field MUST be set to (3) No Such Table Entry if the L-bit is
clear and the address found in the Interface Identification Object
does not appear in the IPv4 Address Resolution Protocol (ARP)
Table table
or the IPv6 Neighbor Cache.

The Code field MUST be set to (4) Multiple Interfaces Satisfy Query
if any of the following conditions apply:

o The L-bit is set and the ICMP Extension Structure identifies more
than one interface that resides in the proxy node node.

o The L-bit is clear and the address found in the Interface
Identification Object maps to multiple IPv4 ARP or IPv6 Neighbor
Cache entries entries.

Otherwise, the Code field MUST be set to (0) No Error Error.

5. Use-Cases Use Cases

In the scenarios listed below, network operators can use PROBE to
determine the status of a probed interface, interface but cannot use PING for
the same purpose. In all scenarios, assume bidirectional
connectivity between the probing and proxy interfaces. However,
bidirectional connectivity between the probing and probed interfaces
is lacking.

o The probed interface is unnumbered unnumbered.

o The probing and probed interfaces are not directly connected to
one another. The probed interface has an IPv6 link-local address, address
but does not have a more globally scoped address address.

o The probing interface runs IPv4 only while the probed interface
runs IPv6 only only.

o The probing interface runs IPv6 only while the probed interface
runs IPv4 only only.

o For lack of a route, the probing node cannot reach the probed
interface.

6. Updates to RFC 4884

Section 4.6 of RFC 4884 [RFC4884] provides a list of extensible ICMP messages
(i.e., messages that can carry the ICMP Extension Structure). This
document adds the ICMP Extended Echo Request message and the ICMP
Extended Echo Reply message to that list.

7. IANA Considerations

This document requests

IANA has performed the following actions from IANA: actions:

o Add an entry Added the following to the "ICMP Type Number" registry, representing Numbers" registry:

42 Extended Echo Request

Added the following to the "Type 42 - Extended Echo Request. This entry has one code Request"
subregistry:

(0) No Error. Error

o Add an entry Added the following to the "ICMPv6 "type" 'type' Numbers" registry, representing
the registry:

160 Extended Echo Request. This entry has one code (0) No Error. Request

As ICMPv6 distinguishes between informational and error
messages, and this is an informational message, the value must be has
been assigned from the range 128-255.

Added the following to the "Type 160 - Extended Echo Request"
subregistry:

(0) No Error

o Add an entry Added the following to the "ICMP Type Number" registry, representing the Numbers" registry:

43 Extended Echo Reply. This entry has Reply

Added the following codes: to the "Type 43 - Extended Echo Reply"
subregistry:

(0) No
Error, Error
(1) Malformed Query, Query
(2) No Such Interface, Interface
(3) No Such Table Entry, Entry
(4) Multiple Interfaces Satisfy Query. Query

o Add an entry Added the following to the "ICMPv6 "type" 'type' Numbers" registry, representing
the registry:

161 Extended Echo Reply. This entry Reply

As ICMPv6 distinguishes between informational and error
messages, and this is an informational message, the value has
been assigned from the range 128-255.

Added the following codes: to the "Type 161 - Extended Echo Reply"
subregistry:

(0) No Error, Error
(1) Malformed Query, Query
(2) No Such Interface, Interface
(3) No Such Table Entry, Entry
(4) Multiple Interfaces Satisfy Query. Query

o Add an entry Added the following to the "ICMP Extension Object Classes and
Class Sub-
types" registry, representing the Sub-types" registry:

(3) Interface Identification Object.
It has Object

Added the following C-types to the "Sub-types - Class 3 -
Interface Identification Object" subregistry:

(0) Reserved (0),
(1) Identifies Interface By by Name (1),
(2) Identifies Interface By by Index (2),
(3) Identifies Interface By by Address
(3).

C-Type values are assignable assigned on a first-come-first-serve First Come First Serve (FCFS)
basis with a range of 0-255.

All codes mentioned above are assigned on a First Come First Serve
(FCFS) an FCFS basis with a range
of 0 -255. 0-255.

8. Security Considerations

The following are legitimate uses of PROBE:

o to determine the operational status of an interface interface.

o to determine which protocols (e.g., IPv4, IPv4 or IPv6) are active on an
interface
interface.

However, malicious parties can use PROBE to obtain additional
information. For example, a malicious party can use PROBE to
discover interface names. Having discovered an interface name, the
malicious party may be able to infer additional information.
Additional information may include:

o interface bandwidth

o the type of device that supports the interface (e.g., vendor
identity)

o the operating system version that the above-mentioned device
executes

Understanding this risk, network operators establish policies that
restrict access to ICMP Extended Echo functionality. In order to
enforce these polices, policies, nodes that support ICMP Extended Echo
functionality MUST support the following configuration options:

o Enable/disable ICMP Extended Echo functionality. By default, ICMP
Extend Echo functionality is disabled.

o Define enabled L-bit settings. By default, L-bit the option to set the
L-bit is enabled and L-bit the option to clear the L-bit is disabled.

o Define enabled query types (i.e., by name, by index, or by
address); by address).
By default, all query types are disabled.

o For each enabled query type, define the prefixes from which ICMP
Extended Echo Request messages are permitted permitted.

o For each interface, determine whether ICMP Echo Request messages
are accepted accepted.

When a node receives an ICMP Extended Echo Request message that it is
not configured to support, it MUST silently discard the message. See
Section 4 for details.

PROBE must not leak information about one Virtual Private Network
(VPN) into another. Therefore, when a node receives an ICMP Extended
Echo Request and the proxy interface is in a different VPN than the
probed interface, the node MUST return an ICMP Extended Echo Reply
with error code equal to (2) No Such Interface.

In order to protect local resources, implementations SHOULD rate-
limit incoming ICMP Extended Echo Request messages.

9. References

9.1. Normative References

[RFC0792] Postel, J., "Internet Control Message Protocol", STD 5,
RFC 792, DOI 10.17487/RFC0792, September 1981,
<https://www.rfc-editor.org/info/rfc792>.

[RFC0826] Plummer, D., "Ethernet Address Resolution Protocol: Or
Converting Network Protocol Addresses to 48.bit Ethernet
Address for Transmission on Ethernet Hardware", STD 37,
RFC 826, DOI 10.17487/RFC0826, November 1982,
<https://www.rfc-editor.org/info/rfc826>.

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.

[RFC4443] Conta, A., Deering, S., and M. Gupta, Ed., "Internet
Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6) Specification", STD 89,
RFC 4443, DOI 10.17487/RFC4443, March 2006,
<https://www.rfc-editor.org/info/rfc4443>.

[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
DOI 10.17487/RFC4861, September 2007,
<https://www.rfc-editor.org/info/rfc4861>.

[RFC4884] Bonica, R., Gan, D., Tappan, D., and C. Pignataro,
"Extended ICMP to Support Multi-Part Messages", RFC 4884,
DOI 10.17487/RFC4884, April 2007,
<https://www.rfc-editor.org/info/rfc4884>.

[RFC7223] Bjorklund, M., "A YANG Data Model for Interface
Management", RFC 7223, DOI 10.17487/RFC7223, May 2014,
<https://www.rfc-editor.org/info/rfc7223>.

[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.

9.2. Informative References

[RFC2151] Kessler, G. and S. Shepard, "A Primer On Internet and TCP/
IP Tools and Utilities", FYI 30, RFC 2151,
DOI 10.17487/RFC2151, June 1997,
<https://www.rfc-editor.org/info/rfc2151>.

[RFC4594] Babiarz, J., Chan, K., and F. Baker, "Configuration
Guidelines for DiffServ Service Classes", RFC 4594,
DOI 10.17487/RFC4594, August 2006,
<https://www.rfc-editor.org/info/rfc4594>.

Appendix A. The PROBE Application

The PROBE application accepts input parameters, sets a counter counter, and
enters a loop to be exited when the counter is equal to zero. 0. On each
iteration of the loop, PROBE emits an ICMP Extended Echo Request,
decrements the counter, sets a timer timer, and waits. The ICMP Extended
Echo Request includes an Identifier and a Sequence Number.

If an ICMP Extended Echo Reply carrying the same Identifier and
Sequence Number arrives, PROBE relays information returned by that
message to its user. However, on each iteration of the loop, PROBE
waits for the timer to expire, expire regardless of whether an Extended Echo
Reply message arrives.

PROBE accepts the following parameters:

o Count

o Wait

o Probing Interface Address

o Hop Count

o Proxy Interface Address

o Local

o Probed Interface Identifier

Count is a positive integer whose default value is 3. Count
determines the number of times that PROBE iterates through the above-
mentioned loop.

Wait is a positive integer whose minimum and default values are 1.
Wait determines the duration of the above-mentioned timer, measured
in seconds.

Probing Interface Address specifies the source address Source Address of the ICMP
Extended Echo Request. The Probing Interface Address MUST be a
unicast address and MUST identify an interface that resides on the
probing node.

The Proxy Interface Address identifies the interface to which the
ICMP Extended Echo Request message is sent. It can must be an IPv4 or
IPv6 unicast address. If it is an IPv4 address, PROBE emits an
ICMPv4 message. If it is an IPv6 address, PROBE emits an ICMPv6
message.

Local is a boolean value. It is TRUE if the proxy and probed
interfaces both reside on the same node. Otherwise, it is FALSE.

The Probed Interface Identifier identifies the probed interface. It
is one of the following:

o an interface name name;

o an address from any address family (e.g., IPv4, IPv6, IEEE 802,
48-bit MAC, or 64-bit MAC) MAC); or

o an if-index if-index.

If the Probed Interface Identifier is an address, it does not need to
be of the same address family as the proxy interface address. For
example, PROBE accepts an IPv4 Proxy Interface Address and an IPv6
Probed Interface Identifier Identifier.

Acknowledgments

Thanks to Sowmini Varadhan, Jeff Haas, Carlos Pignataro, Jonathan
Looney, Dave Thaler, Mikio Hara, Joel Halpern, Yaron Sheffer, Stefan
Winter, Jean-Michel Combes, Amanda Barber Barber, and Joe Touch for their
thoughtful review of this document.

Authors' Addresses

Ron Bonica
Juniper Networks
2251 Corporate Park Drive
Herndon, Virginia 20171
USA
United States of America

Email: rbonica@juniper.net

Reji Thomas
Juniper Networks
Elnath-Exora Business Park Survey
Bangalore, Karnataka 560103
India

Email: rejithomas@juniper.net
Jen Linkova
Google
1600 Amphitheatre Parkway
Mountain View, California 94043
USA
United States of America

Email: furry@google.com

Chris Lenart
Verizon
22001 Loudoun County Parkway
Ashburn, Virginia 20147
USA
United States of America

Email: chris.lenart@verizon.com

Mohamed Boucadair
Orange
Rennes 35000
France

Email: mohamed.boucadair@orange.com