Network Working Group
Internet Engineering Task Force (IETF) J. Dong
Internet-Draft
Request for Comments: 8944 X. Wei
Intended status:
Category: Standards Track Q. Wu
Expires: March 14, 2021
ISSN: 2070-1721 Huawei
M. Boucadair
Orange
A. Liu
Tecent
September 10,
November 2020
A YANG Data Model for Layer 2 Network Topologies
draft-ietf-i2rs-yang-l2-network-topology-18
Abstract
This document defines a YANG data model for Layer 2 network
topologies. In particular, this data model augments the generic
network and network topology data models with Layer 2 specific topology attributes.
Editorial Note (To be removed by RFC Editor)
Please update these statements within the document with the RFC
number to be assigned attributes
that are specific to this document:
o "This version of this YANG module is part of RFC XXXX;"
o "RFC XXXX: A YANG Data Model for Layer 2 Network Topologies";
o reference: RFC XXXX
Please update the "revision" date of the YANG module. 2.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of six months RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on March 14, 2021.
https://www.rfc-editor.org/info/rfc8944.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Layer 2 Topology Model . . . . . . . . . . . . . . . . . . . 3
4. Layer 2 Topology YANG Module . . . . . . . . . . . . . . . . 7
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 19
6. Security Considerations . . . . . . . . . . . . . . . . . . . 20
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 21
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.1.
7.1. Normative References . . . . . . . . . . . . . . . . . . 21
8.2.
7.2. Informative References . . . . . . . . . . . . . . . . . 23
Appendix A. Companion YANG Module for Non-NMDA Compliant Non-NMDA-Compliant
Implementations . . . . . . . . . . . . . . . . . . 24
Appendix B. An Example . . . . . . . . . . . . . . . . . . . . . 28
Acknowledgements
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 33
1. Introduction
[RFC8345] defines the YANG [RFC6020] [RFC7950] data models of the
abstract (generic) network and network topology. Such models can be
augmented with technology-specific details to build more specific
topology models.
This document defines the YANG data model for Layer 2 (L2) network
topologies by augmenting the generic network (Section 6.1 of
[RFC8345]) and network topology (Section 6.2 of [RFC8345]) data
models with L2-specific topology attributes. An example is provided
in Appendix B.
There are multiple applications for such a data model. For example,
within the context of Interface to the Routing System (I2RS), nodes
within the network can use the data model to capture their
understanding of the overall network topology and expose it to a
network controller. A network controller can then use the
instantiated topology data to compare and reconcile its own view of
the network topology with that of the network elements that it
controls. Alternatively, nodes within the network may compare and
reconcile this understanding either among themselves or with the help
of a controller. Beyond the network element and the immediate
context of I2RS itself, a network controller might even use the data
model to represent its view of the topology that it controls and
expose it to external applications. Further use cases where the data
model can be applied are described in [I2RS-UR].
This document uses the common YANG types defined in [RFC6991] and
adopts the Network Management Datastore Architecture (NMDA)
[RFC8342].
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
The terminology for describing YANG modules is defined in [RFC7950].
The meanings of the symbols used in the tree diagram are defined in
[RFC8340].
3. Layer 2 Topology Model
The Layer 2 network topology YANG module is designed to be generic
and applicable to Layer 2 networks built with different Layer 2
technologies. It can be used to describe both the physical and the
logical (virtual) Layer 2 network topologies.
The relationship between the Layer 2 topology module and the generic
network and network topology module is shown in Figure 1. In order
to represent a Layer 2 network topology, the generic network and
topology models are augmented with Layer 2 specific L2-specific information, such as
the identifiers, identities (e.g., Provider Backbone Bridging
[IEEE802.1ah], QinQ [IEEE802.1ad], or VXLAN Virtual eXtensible Local Area
Network (VXLAN) [RFC7348]), attributes, and states of the Layer 2
networks, nodes, links, and termination points. Some of the
information may be collected via Link Layer Discovery Protocol (LLDP)
[IEEE802.1AB] or other Layer 2 protocols, and some of them may be
locally configured.
+---------------------+
| ietf-network |
+----------^----------+
|
|
+---------------------+
|ietf-network-topology|
+----------^----------+
|
|
+----------^----------+
| ietf-l2-topology |
+---------------------+
Figure 1: Layer 2 Topology YANG Module Structure
The structure of the "ietf-l2-topology" YANG module is depicted in
the following tree diagram:
module: ietf-l2-topology
augment /nw:networks/nw:network/nw:network-types:
+--rw l2-topology!
augment /nw:networks/nw:network:
+--rw l2-topology-attributes
+--rw name? string
+--rw flags* l2-flag-type
augment /nw:networks/nw:network/nw:node:
+--rw l2-node-attributes
+--rw name? string
+--rw flags* node-flag-type
+--rw bridge-id* string
+--rw management-address* inet:ip-address
+--rw management-mac? yang:mac-address
+--rw management-vlan? string
augment /nw:networks/nw:network/nt:link:
+--rw l2-link-attributes
+--rw name? string
+--rw flags* link-flag-type
+--rw rate? uint64
+--rw delay? uint32
+--rw auto-nego? boolean
+--rw duplex? duplex-mode
augment /nw:networks/nw:network/nw:node/nt:termination-point:
+--rw l2-termination-point-attributes
+--rw interface-name? string
+--rw mac-address? yang:mac-address
+--rw port-number* uint32
+--rw unnumbered-id* uint32
+--rw encapsulation-type? identityref
+--rw outer-tag? dot1q-types:vid-range-type {VLAN}?
+--rw outer-tpid? dot1q-types:dot1q-tag-type {QinQ}?
+--rw inner-tag? dot1q-types:vid-range-type {VLAN}?
+--rw inner-tpid? dot1q-types:dot1q-tag-type {QinQ}?
+--rw lag? boolean
+--rw member-link-tp*
-> /nw:networks/network/node/nt:termination-point/tp-id
+--rw vxlan {VXLAN}?
+--rw vni-id? vni
notifications:
+---n l2-node-event
| +--ro event-type? l2-network-event-type
| +--ro node-ref?
-> /nw:networks/network[nw:network-id=current()
/../network-ref]/node/node-id
| +--ro network-ref? -> /nw:networks/network/network-id
| +--ro l2-topology!
| +--ro l2-node-attributes
| +--ro name? string
| +--ro flags* node-flag-type
| +--ro bridge-id* uint64
| +--ro management-address* inet:ip-address
| +--ro management-mac? yang:mac-address
| +--ro management-vlan? string
+---n l2-link-event
| +--ro event-type? l2-network-event-type
| +--ro link-ref?
-> /nw:networks/network[nw:network-id=current()
/../network-ref]/nt:link/link-id
| +--ro network-ref? -> /nw:networks/network/network-id
| +--ro l2-topology!
| +--ro l2-link-attributes
| +--ro name? string
| +--ro flags* link-flag-type
| +--ro rate? uint64
| +--ro delay? uint32
| +--ro auto-nego? boolean
| +--ro duplex? duplex-mode
+---n l2-termination-point-event
+--ro event-type? l2-network-event-type
+--ro tp-ref?
-> /nw:networks/network[nw:network-id=current()
/../network-ref]/node[nw:node-id=current()
/../node-ref]/nt:termination-point/tp-id
+--ro node-ref?
-> /nw:networks/network[nw:network-id=current()
/../network-ref]/node/node-id
+--ro network-ref? -> /nw:networks/network/network-id
+--ro l2-topology!
+--ro l2-termination-point-attributes
+--ro interface-name? string
+--ro mac-address? yang:mac-address
+--ro port-number* uint32
+--ro unnumbered-id* uint32
+--ro encapsulation-type? identityref
+--ro outer-tag? dot1q-types:vid-range-type {VLAN}?
+--ro outer-tpid? dot1q-types:dot1q-tag-type {QinQ}?
+--ro inner-tag? dot1q-types:vid-range-type {VLAN}?
+--ro inner-tpid? dot1q-types:dot1q-tag-type {QinQ}?
+--ro lag? boolean
+--ro member-link-tp*
-> /nw:networks/network/node/nt:termination-point/tp-id
+--ro vxlan {VXLAN}?
+--ro vni-id? vni
The Layer 2 topology Topology YANG module augments the "ietf-network" and
"ietf-network-topology" YANG modules as follows:
o
* A new network type "l2-network-type" is introduced. This is
represented by a container object, object and is inserted under the
"network-types" container of the generic "ietf-network" module
defined in Section 6.1 of [RFC8345].
o
* Additional network attributes are introduced in a grouping "l2-
network-attributes", which augments the "network" list of the
"ietf-network" module. The attributes include the Layer 2 network
name and a set of flags. Each type of flag is represented by a
separate identity.
o
* Additional data objects for Layer 2 nodes are introduced by
augmenting the "node" list of the generic "ietf-network" module.
New objects include the Layer 2 node identifier, management
address, management mac, mangement vlan MAC address, management VLAN, and a set of
flags.
o
* Additional data objects for Layer 2 termination points are
introduced by augmenting the "termination-point" list of the
"ietf-network-topology" module defined in Section 6.2 of
[RFC8345]. New objects include the interface name, encapsulation
type, lag support indication, and attributes that are specific to
the Layer 2 termination point type specific
attributes.
o type.
* Links in the "ietf-network-topology" module are augmented as well
with a set of Layer 2 parameters, allowing to associate a link
with a name, a set of Layer 2 link attributes, and flags.
o
* Some optional Layer 2 technology specific technology-specific attributes are
introduced in this module as Layer 2 features because these
attributes may be useful to expose to above services/applications.
Note that learning or configuring advanced Layer 2 technology-
specific attributes is not within the scope of the Layer 2
Topology YANG module; dedicated YANG modules should be used
instead (e.g., [I-D.ietf-trill-yang]). [TRILL-YANG]).
4. Layer 2 Topology YANG Module
This module uses types defined in [RFC6991], [RFC7224],
[IEEE802.1Qcp], and [RFC8345]. It also references [RFC4761],
[RFC4762], [IEEE802.1Q-2014],
[IEEE802.1ad], [RFC7348], and [RFC4202]. [RFC7727].
<CODE BEGINS> file "ietf-l2-topology@2020-06-29.yang" "ietf-l2-topology@2020-11-02.yang"
module ietf-l2-topology {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-l2-topology";
prefix l2t;
import ietf-network {
prefix nw;
reference
"RFC 8345: A YANG Data Model for Network Topologies";
}
import ietf-network-topology {
prefix nt;
reference
"RFC 8345: A YANG Data Model for Network Topologies";
}
import ietf-inet-types {
prefix inet;
reference
"RFC 6991:Common YANG Data Types";
}
import ietf-yang-types {
prefix yang;
reference
"RFC 6991:Common YANG Data Types";
}
import iana-if-type {
prefix ianaift;
reference
"RFC 7224: IANA Interface Type YANG Module";
}
import ieee802-dot1q-types {
prefix dot1q-types;
reference
"IEEE Std 802.1Qcp-2018: Bridges and Bridged
Networks - Amendment: YANG Data Model";
}
organization
"IETF I2RS (Interface to the Routing System) Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/i2rs/>
WG List: <mailto:i2rs@ietf.org>
Editor: Jie Dong
<mailto:jie.dong@huawei.com>
Editor: Xiugang Wei
<mailto:weixiugang@huawei.com>
Editor: Qin Wu
<mailto:bill.wu@huawei.com>
Editor: Mohamed Boucadair
<mailto:mohamed.boucadair@orange.com>
Editor: Anders Liu
<andersliu@tencent.com>";
<mailto:andersliu@tencent.com>";
description
"This module defines a basic model for the Layer 2 topology
of a network.
Copyright (c) 2020 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; 8944; see
the RFC itself for full legal notices.";
revision 2020-06-29 2020-11-02 {
description
"Initial revision"; revision.";
reference
"RFC XXXX: 8944: A YANG Data Model for Layer 2 Network Topologies";
}
feature VLAN {
description
"Enables VLAN tag support as defined in IEEE 802.1Q.";
reference
"IEEE Std 802.1Q-2014: Bridges and Bridged Networks";
}
feature QinQ {
description
"Enables QinQ double tag support as defined in IEEE 802.1ad.";
reference
"IEEE Std 802.1ad: Provider Bridges";
}
feature VXLAN {
description
"Enables VXLAN support as defined in RFC7348."; RFC 7348.";
reference
"RFC 7348: Virtual eXtensible Local Area Network (VXLAN):
A Framework for Overlaying Virtualized Layer 2
Networks over Layer 3 Networks";
}
identity flag-identity {
description
"Base type for flags.";
}
identity eth-encapsulation-type {
base ianaift:iana-interface-type;
description
"Base identity from which specific Ethernet
encapsulation types are derived.";
reference
"RFC 7224: IANA Interface Type YANG Module";
}
identity ethernet {
base eth-encapsulation-type;
description
"Native Ethernet encapsulation.";
}
identity vlan {
base eth-encapsulation-type;
description
"VLAN encapsulation.";
}
identity qinq {
base eth-encapsulation-type;
description
"QinQ encapsulation.";
}
identity pbb {
base eth-encapsulation-type;
description
"Provider-backbone-bridging
"Provider Backbone Bridging (PBB) encapsulation.
The PBB functions are developed in IEEE 802.1ah.";
}
identity trill {
base eth-encapsulation-type;
description
"TRILL
"Transparent Interconnection of Lots of Links (TRILL)
encapsulation.";
}
identity vpls {
base eth-encapsulation-type;
description
"Ethernet VPLS Virtual Private LAN Service (VPLS)
interface encapsulation.";
}
identity vxlan {
base eth-encapsulation-type;
description
"VXLAN MAC Media Access Control (MAC) in UDP encapsulation.";
reference
"RFC 7348: Virtual eXtensible Local Area Network (VXLAN):
A Framework for Overlaying Virtualized Layer 2
Networks over Layer 3 Networks";
}
typedef vni {
type uint32 {
range "0..16777215";
}
description
"VXLAN Network Identifier or VXLAN Segment ID.
It allows up to 16 M VXLAN segments to coexist
within the same administrative domain.
The use of value '0' is implementation-specific."; implementation specific.";
reference
"RFC 7348: Virtual eXtensible Local Area Network (VXLAN):
A Framework for Overlaying Virtualized Layer 2
Networks over Layer 3 Networks";
}
typedef l2-flag-type {
type identityref {
base flag-identity;
}
description
"Base type for L2 flags. One example of L2 flag
type is trill trill, which represents the trill topology
type.";
}
typedef node-flag-type {
type identityref {
base flag-identity;
}
description
"Node flag attributes. The physical node can be
one example of a node flag attribute.";
}
typedef link-flag-type {
type identityref {
base flag-identity;
}
description
"Link flag attributes. One example of a link flag
attribute is the pseudowire.";
}
typedef l2-network-event-type {
type enumeration {
enum addition {
value 0;
description
"A Layer 2 node or link or termination-point
has been added.";
}
enum removal {
value 1;
description
"A Layer 2 node or link or termination-point
has been removed.";
}
enum update {
value 2;
description
"A Layer 2 node or link or termination-point
has been updated.";
}
}
description
"Layer 2 network event type for notifications.";
}
typedef duplex-mode {
type enumeration {
enum full-duplex {
description
"Indicates full-duplex mode.";
}
enum half-duplex {
description
"Indicates half-duplex mode.";
}
}
description
"Indicates the type of the duplex mode.";
}
grouping l2-network-type {
description
"Indicates the topology type to be L2.";
container l2-topology {
presence "Indicates L2 Network Topology.";
description
"The presence of the container node indicates
L2 Network Topology.";
}
}
grouping l2-topology-attributes {
description
"L2 Topology topology scope attributes.";
container l2-topology-attributes {
description
"Contains L2 topology attributes.";
leaf name {
type string;
description
"Name of the topology.";
}
leaf-list flags {
type l2-flag-type;
description
"Topology flags.";
}
}
}
grouping l2-node-attributes {
description
"L2 node attributes"; attributes.";
container l2-node-attributes {
description
"Contains L2 node attributes.";
leaf name {
type string;
description
"Node name.";
}
leaf-list flags {
type node-flag-type;
description
"Node flags. It can be used to indicates indicate
node flag attributes.";
}
leaf-list bridge-id {
type string {
pattern '[0-9a-fA-F]{2}(:[0-9a-fA-F]{2}){7}';
}
description
"This is the bridge identifier represented as a
hexadecimal 8 octet 8-octet string. It has 4 bits of
priority, 12 bits of MSTI-ID Multiple Spanning Tree
Instance Identifier (MSTI-ID), and the base bridge
identifier. There may be multiple one for each
spanning tree instance.";
reference
"RFC 7727: Spanning Tree Protocol (STP) Application of
the Inter-Chassis Communication Protocol
(ICCP)";
}
leaf-list management-address {
type inet:ip-address;
description
"IP address used for management purpose.";
}
leaf management-mac {
type yang:mac-address;
description
"This is a MAC address used for the bridge management.
It can be the Bridge Base VID, VLAN ID (VID), interface
MAC address address, or other. ";
}
leaf management-vlan {
type string;
description
"This is a VLAN that supports the Management management address.
The actual VLAN ID type and value would be a member of
this VLAN.";
}
}
}
grouping l2-link-attributes {
description
"L2 link attributes"; attributes.";
container l2-link-attributes {
description
"Contains L2 link attributes.";
leaf name {
type string;
description
"Link name.";
}
leaf-list flags {
type link-flag-type;
description
"Link flags. It can be used to indicate
link flag attributes.";
}
leaf rate {
type uint64;
units "Kbps";
description
"Link rate. It specifies bandwidth requirements
associated with the specific link. The link
contains a source and a destination.";
}
leaf delay {
type uint32;
units "microseconds";
description
"Unidirectional Link link delay in
microseconds.";
}
leaf auto-nego {
type boolean;
default "true";
description
"Set to true if auto negotiation auto-negotiation is supported.
Set to false if auto negotiation auto-negotiation is not supported.";
}
leaf duplex {
type duplex-mode;
description
"Expose
"Exposes the duplex mode, full duplex full-duplex or half-duplex.";
}
}
}
grouping l2-termination-point-attributes {
description
"L2 termination point attributes"; attributes.";
container l2-termination-point-attributes {
description
"Containing L2 termination point attributes.";
leaf interface-name {
type string;
description
"Name of the interface. The name can (but does not
have to) correspond to an interface reference of a
containing node's interface, i.e., the path name of a
corresponding interface data node on the containing
node is reminiscent of data type interface-ref defined
in RFC 8343. It should be noted that data type
interface-ref of RFC 8343 cannot be used directly,
as this data type is used to reference an interface
in a datastore of a single node in the network, not
to uniquely reference interfaces across a network.";
}
leaf mac-address {
type yang:mac-address;
description
"Interface MAC address for logical link control.";
}
leaf-list port-number {
type uint32;
description
" List of port numbers of the Bridge bridge ports for which each
entry contains Bridge bridge management information.";
}
leaf-list unnumbered-id {
type uint32;
description
"List of unnumbered interface identifiers.
The unnumbered interface identifier will correspond to
the ifIndex value of the interface, i.e., the ifIndex
value of the ifEntry that represents the interface in
implementations where the Interfaces Group MIB
(RFC 2863) is supported.";
}
leaf encapsulation-type {
type identityref {
base eth-encapsulation-type;
}
description
"Encapsulation type of this
termination point.";
}
leaf outer-tag {
if-feature "VLAN";
type dot1q-types:vid-range-type;
description
"The outermost VLAN tag. It may include a list of VLAN
Ids,
Ids or non overlapping nonoverlapping VLAN ranges.";
}
leaf outer-tpid {
if-feature "QinQ";
type dot1q-types:dot1q-tag-type;
description
"Identifies a specific 802.1Q tag type of outermost VLAN
tag.";
}
leaf inner-tag {
if-feature "VLAN";
type dot1q-types:vid-range-type;
description
"The inner VLAN tag. It may include a list of VLAN
Ids,
Ids or non overlapping nonoverlapping VLAN ranges.";
}
leaf inner-tpid {
if-feature "QinQ";
type dot1q-types:dot1q-tag-type;
description
"Identifies a specific 802.1Q tag type of inner VLAN tag.";
}
leaf lag {
type boolean;
default "false";
description
"Defines whether lag is supported or not.
When it is set to true, the lag is supported.";
}
leaf-list member-link-tp {
when "../lag = 'true'" {
description
"Relevant only when the lag interface is supported.";
}
type leafref {
path "/nw:networks/nw:network/nw:node/nt:termination-point/nt:tp-id"; "/nw:networks/nw:network/nw:node"
+ "/nt:termination-point/nt:tp-id";
}
description
"List of member link termination points associated with
specific l2 L2 termination point.";
}
container vxlan {
when "derived-from-or-self(../encapsulation-type, 'l2t:vxlan')" "
+ "'l2t:vxlan')" {
description
"Only applies when the type of the Ethernet
encapsulation is 'vxlan'.";
}
if-feature "VXLAN";
leaf vni-id {
type vni;
description
"VXLAN Network Identifier (VNI).";
}
description
"Vxlan encapsulation type.";
}
}
}
augment "/nw:networks/nw:network/nw:network-types" {
description
"Introduces new network type for L2 topology.";
uses l2-network-type;
}
augment "/nw:networks/nw:network" {
when '/nw:networks/nw:network/nw:network-types/l2t:l2-topology' {
description
"Augmentation parameters apply only for networks
with L2 topology.";
}
description
"Configuration parameters for the L2 network
as a whole.";
uses l2-topology-attributes;
}
augment "/nw:networks/nw:network/nw:node" {
when '/nw:networks/nw:network/nw:network-types/l2t:l2-topology' {
description
"Augmentation parameters apply only for networks
with L2 topology.";
}
description
"Configuration parameters for L2 at the node
level.";
uses l2-node-attributes;
}
augment "/nw:networks/nw:network/nt:link" {
when '/nw:networks/nw:network/nw:network-types/l2t:l2-topology' {
description
"Augmentation parameters apply only for networks
with L2 topology.";
}
description
"Augments L2 topology link information.";
uses l2-link-attributes;
}
augment "/nw:networks/nw:network/nw:node/nt:termination-point" {
when '/nw:networks/nw:network/nw:network-types/l2t:l2-topology' {
description
"Augmentation parameters apply only for networks
with L2 topology.";
}
description
"Augments L2 topology termination point information.";
uses l2-termination-point-attributes;
}
notification l2-node-event {
description
"Notification event for L2 node.";
leaf event-type {
type l2-network-event-type;
description
"Event type.";
}
uses nw:node-ref;
uses l2-network-type;
uses l2-node-attributes;
}
notification l2-link-event {
description
"Notification event for L2 link.";
leaf event-type {
type l2-network-event-type;
description
"Event type.";
}
uses nt:link-ref;
uses l2-network-type;
uses l2-link-attributes;
}
notification l2-termination-point-event {
description
"Notification event for L2 termination point.";
leaf event-type {
type l2-network-event-type;
description
"Event type.";
}
uses nt:tp-ref;
uses l2-network-type;
uses l2-termination-point-attributes;
}
}
<CODE ENDS>
5. IANA Considerations
This document requests
IANA to register has registered the following URIs in the "ns" subregistry within the "IETF
"The IETF XML Registry" [RFC3688]:
URI: urn:ietf:params:xml:ns:yang:ietf-l2-topology
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:ietf-l2-topology-state
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
This document requests
IANA to register has registered the following YANG modules in the "YANG Module
Names" subregistry [RFC6020] within the "YANG Parameters" registry.
name:
Name: ietf-l2-topology
namespace:
Namespace: urn:ietf:params:xml:ns:yang:ietf-l2-topology
prefix:
Prefix: l2t
reference:
Reference: RFC XXXX
name: 8944
Name: ietf-l2-topology-state
namespace:
Namespace: urn:ietf:params:xml:ns:yang:ietf-l2-topology-state
prefix:
Prefix: l2t-s
reference:
Reference: RFC XXXX 8944
These modules are not maintained by IANA.
6. Security Considerations
The YANG module modules specified in this document defines define a schema for data
that is designed to be accessed via network management protocols protocols,
such as NETCONF Network Configuration Protocol (NETCONF) [RFC6241] or
RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport
layer, and the mandatory-to-implement secure transport is Secure
Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the
mandatory-to-implement secure transport is TLS [RFC8446].
The Network Configuration Access Control Model (NACM) [RFC8341]
provides the means to restrict access for particular NETCONF or
RESTCONF users to a preconfigured subset of all available NETCONF or
RESTCONF protocol operations and content.
The Layer 2 topology module defines information that can be
configurable in certain instances, for example example, in the case of
virtual topologies that can be created by client applications. In
such cases, a malicious client could introduce topologies that are
undesired. Specifically, a malicious client could attempt to remove
or add a node, a link, or a termination point, point by creating or deleting
corresponding elements in the node, link, and termination point
lists, respectively. In the case of a topology that is learned, the
server will automatically prohibit such misconfiguration attempts.
In the case of a topology that is configured, i.e. i.e., whose origin is
"intended", the undesired configuration could become effective and be
reflected in the operational state datastore [RFC8342], leading to
disruption of services provided via this topology. For those
reasons, it is important that the NACM is vigorously applied to
prevent topology misconfiguration by unauthorized clients.
There are a number of data nodes defined in this YANG module that are
writable/creatable/deletable (i.e., config true, which is the
default). These data nodes may be considered sensitive or vulnerable
in some network environments. Write operations (e.g., edit-config)
to these data nodes without proper protection can have a negative
effect on network operations. These are the subtrees and data nodes
and their sensitivity/vulnerability:
o
l2-network-attributes:
A malicious client could attempt to sabotage the configuration of
any of the contained attributes, such as the name or the flag data
nodes.
o
l2-node-attributes:
A malicious client could attempt to sabotage the configuration of
important node attributes, such as the name or the management-address.
o management-
address.
l2-link-attributes:
A malicious client could attempt to sabotage the configuration of
important link attributes, such as the rate or the delay data
nodes.
o
l2-termination-point-attributes:
A malicious client could attempt to sabotage the configuration of
important termination point attributes (e.g., 'maximum-frame-size'). 'maximum-frame-
size').
Some of the readable data nodes in this YANG module may be considered
sensitive or vulnerable in some network environments. It is thus
important to control read access (e.g., via get, get-config, or
notification) to these data nodes. In particular, the YANG model module
for
layer Layer 2 topology may expose sensitive information, for example example,
the MAC addresses of devices, devices or VLAN/VXLAN identifiers. Unrestricted
use of such information can lead to privacy violations. For example,
listing MAC addresses in a network allows monitoring of devices and
their movements. Location information can be derived from MAC
addresses of network devices, bypassing protection of location
information by the Operating System.
7. Acknowledgements
The authors would like to acknowledge the comments and suggestions
received from Susan Hares, Alia Atlas, Juergen Schoenwaelder, Mach
Chen, Alexander Clemm, Sriganesh Kini, Oscar Gonzalez de Dios, Stig
Venaas, Christian Huitema, and Meral Shirazipour,Benjamin Kaduk,Don
Fedyk.
Many thanks to Ladislav Lhotka for the yang-doctors review.
8. References
8.1.
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
<https://www.rfc-editor.org/info/rfc3688>.
[RFC4202] Kompella, K., Ed. and Y. Rekhter, Ed., "Routing Extensions
in Support of Generalized Multi-Protocol Label Switching
(GMPLS)", RFC 4202, DOI 10.17487/RFC4202, October 2005,
<https://www.rfc-editor.org/info/rfc4202>.
[RFC4761] Kompella, K., Ed. and Y. Rekhter, Ed., "Virtual Private
LAN Service (VPLS) Using BGP for Auto-Discovery and
Signaling", RFC 4761, DOI 10.17487/RFC4761, January 2007,
<https://www.rfc-editor.org/info/rfc4761>.
[RFC4762] Lasserre, M., Ed. and V. Kompella, Ed., "Virtual Private
LAN Service (VPLS) Using Label Distribution Protocol (LDP)
Signaling", RFC 4762, DOI 10.17487/RFC4762, January 2007,
<https://www.rfc-editor.org/info/rfc4762>.
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
<https://www.rfc-editor.org/info/rfc6020>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/rfc6241>.
[RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure
Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
<https://www.rfc-editor.org/info/rfc6242>.
[RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types",
RFC 6991, DOI 10.17487/RFC6991, July 2013,
<https://www.rfc-editor.org/info/rfc6991>.
[RFC7224] Bjorklund, M., "IANA Interface Type YANG Module",
RFC 7224, DOI 10.17487/RFC7224, May 2014,
<https://www.rfc-editor.org/info/rfc7224>.
[RFC7348] Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger,
L., Sridhar, T., Bursell, M., and C. Wright, "Virtual
eXtensible Local Area Network (VXLAN): A Framework for
Overlaying Virtualized Layer 2 Networks over Layer 3
Networks", RFC 7348, DOI 10.17487/RFC7348, August 2014,
<https://www.rfc-editor.org/info/rfc7348>.
[RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC7950, August 2016,
<https://www.rfc-editor.org/info/rfc7950>.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/info/rfc8040>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8341] Bierman, A. and M. Bjorklund, "Network Configuration
Access Control Model", STD 91, RFC 8341,
DOI 10.17487/RFC8341, March 2018,
<https://www.rfc-editor.org/info/rfc8341>.
[RFC8345] Clemm, A., Medved, J., Varga, R., Bahadur, N.,
Ananthakrishnan, H., and X. Liu, "A YANG Data Model for
Network Topologies", RFC 8345, DOI 10.17487/RFC8345, March
2018, <https://www.rfc-editor.org/info/rfc8345>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/info/rfc8446>.
8.2.
7.2. Informative References
[I-D.ietf-trill-yang]
Weiguo, H., Yizhou, L., Kumar, D., Durrani, M., Zhai, H.,
and L. Xia, "TRILL YANG Data Model", draft-ietf-trill-
yang-04 (work in progress), December 2015.
[I2RS-UR] Hares, S. and M. Chen, "Summary of I2RS Use Case
Requirements", draft-ietf-i2rs-usecase-reqs-summary-03
(work Work in progress), Progress, Internet-Draft, draft-
ietf-i2rs-usecase-reqs-summary-03, 15 November 2016. 2016,
<https://tools.ietf.org/html/draft-ietf-i2rs-usecase-reqs-
summary-03>.
[IEEE802.1AB]
"Station
IEEE, "IEEE Standard for Local and metropolitan area
networks - Station and Media Access Control Connectivity
Discovery", IEEE Std 802.1AB-2016,
DOI 10.1109/IEEESTD.2016.7433915, March 2016. 2016,
<https://doi.org/10.1109/IEEESTD.2016.7433915>.
[IEEE802.1ad]
"Virtual
IEEE, "IEEE Standard for Local and Metropolitan Area
Networks--Virtual Bridged Local Area Networks Amendment Networks--Amendment
4: Provider Bridges", IEEE Std 802.1ad-2005,
DOI 10.1109/IEEESTD.2006.6044678, May 2006. 2006,
<https://doi.org/10.1109/IEEESTD.2006.6044678>.
[IEEE802.1ah]
"Virtual
IEEE, "IEEE Standard for Local and metropolitan area
networks -- Virtual Bridged Local Area Networks Amendment 4:
7: Provider Backbone Bridges", IEEE Std 802.1ah-2008,
DOI 10.1109/IEEESTD.2008.4602826, August 2008. 2008,
<https://doi.org/10.1109/IEEESTD.2008.4602826>.
[IEEE802.1Q-2014]
IEEE, "IEEE Standard for Local and metropolitan area
networks--Bridges and Bridged Networks", IEEE 802.1Q-2014,
DOI 10.1109/IEEESTD.2014.6991462, December 2014,
<https://doi.org/10.1109/IEEESTD.2014.6991462>.
[IEEE802.1Qcp]
"Bridges
IEEE, "IEEE Standard for Local and metropolitan area
networks--Bridges and Bridged Networks - Amendment: Networks--Amendment 30: YANG
Data Model", IEEE Std 802.1Qcp-2018,
DOI 10.1109/IEEESTD.2018.8467507, September 2018.
[RFC6241] Enns, R., Ed., Bjorklund, 2018,
<https://doi.org/10.1109/IEEESTD.2018.8467507>.
[RFC7727] Zhang, M., Ed., Schoenwaelder, J., Ed., Wen, H., and A. Bierman, Ed., "Network Configuration J. Hu, "Spanning Tree Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/rfc6241>.
[RFC6242] Wasserman, M., "Using
(STP) Application of the NETCONF Inter-Chassis Communication
Protocol over Secure
Shell (SSH)", (ICCP)", RFC 6242, 7727, DOI 10.17487/RFC6242, June 2011,
<https://www.rfc-editor.org/info/rfc6242>. 10.17487/RFC7727, January
2016, <https://www.rfc-editor.org/info/rfc7727>.
[RFC7951] Lhotka, L., "JSON Encoding of Data Modeled with YANG",
RFC 7951, DOI 10.17487/RFC7951, August 2016,
<https://www.rfc-editor.org/info/rfc7951>.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/info/rfc8040>.
[RFC8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
<https://www.rfc-editor.org/info/rfc8340>.
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
<https://www.rfc-editor.org/info/rfc8342>.
[TRILL-YANG]
Hao, W., Li, Y., Kumar, D., Durrani, M., Zhai, H., and L.
Xia, "TRILL YANG Data Model", Work in Progress, Internet-
Draft, draft-ietf-trill-yang-04, 20 December 2015,
<https://tools.ietf.org/html/draft-ietf-trill-yang-04>.
Appendix A. Companion YANG Module for Non-NMDA Compliant Non-NMDA-Compliant
Implementations
The YANG module ietf-l2-topology defined in this document augments
two modules, "ietf-network" and "ietf-network-topology", that are
designed to be used in conjunction with implementations that support
the Network Management Datastore Architecture (NMDA) defined in
[RFC8342]. In order to allow implementations to use the model even
in cases when NMDA is not supported, a set of companion modules have
been defined that represent a state model of networks and network
topologies, "ietf-network-state" and "ietf-network-topology-state",
respectively.
In order to be able to use the model for layer Layer 2 topologies defined
in this document in conjunction with non-NMDA compliant non-NMDA-compliant
implementations, a corresponding companion module is defined that
represents the operational state of layer Layer 2 network topologies. The
module "ietf-l2-topology-state" mirrors the module "ietf-l2-topology"
defined in Section 4. However, it augments "ietf-network-state" and
"ietf-network-topology-state" (instead of "ietf-network" and "ietf-
network-topology") and all its data nodes are non-configurable. nonconfigurable.
The companion module "ietf-l2-topology" SHOULD NOT be supported by
implementations that support NMDA. It is for this reason that this
module is defined in the informative Appendix. appendix.
As the structure of this modules module mirrors that of its underlying
modules, the YANG tree is not depicted separately.
<CODE BEGINS> file "ietf-l2-topology-state@2020-06-29.yang" "ietf-l2-topology-state@2020-11-02.yang"
module ietf-l2-topology-state {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-l2-topology-state";
prefix l2t-s;
import ietf-network-state {
prefix nw-s;
reference
"RFC 8345: A YANG Data Model for Network Topologies";
}
import ietf-network-topology-state {
prefix nt-s;
reference
"RFC 8345: A YANG Data Model for Network Topologies";
}
import ietf-l2-topology {
prefix l2t;
reference
"RFC XXXX: 8944: A YANG Data Model for Layer 2 Network Topologies";
}
organization
"IETF I2RS (Interface to the Routing System) Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/i2rs/>
WG List: <mailto:i2rs@ietf.org>
Editor: Jie Dong
<mailto:jie.dong@huawei.com>
Editor: Xiugang Wei
<mailto:weixiugang@huawei.com>
Editor: Qin Wu
<mailto:bill.wu@huawei.com>
Editor: Mohamed Boucadair
<mailto:mohamed.boucadair@orange.com>
Editor: Anders Liu
<andersliu@tencent.com>";
description
"This module defines a model for Layer 2 Network Topology
state, representing topology that either is learned or
results from applying topology that has been configured per
the 'ietf-l2-topology' model, mirroring the
corresponding data nodes in this model.
This model mirrors 'ietf-l2-topology' but contains only
read-only state data. The model is not needed when the
underlying implementation infrastructure supports the
Network Management Datastore Architecture (NMDA).
Copyright (c) 2020 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; 8944; see
the RFC itself for full legal notices.";
revision 2020-06-29 2020-11-02 {
description
"Initial revision"; revision.";
reference
"RFC XXXX: 8944: A YANG Data Model for Layer 2 Network Topologies";
}
/*
* Data nodes
*/
augment "/nw-s:networks/nw-s:network/nw-s:network-types" {
description
"Introduces a new network type for L2 topology.";
uses l2t:l2-network-type;
}
augment "/nw-s:networks/nw-s:network" {
when 'nw-s:network-types/l2t-s:l2-topology' {
description
"Augmentation parameters apply only for networks
with L2 topology.";
}
description
"Configuration parameters for the L2 network
as a whole.";
uses l2t:l2-topology-attributes;
}
augment "/nw-s:networks/nw-s:network/nw-s:node" {
when '../nw-s:network-types/l2t-s:l2-topology' {
description
"Augmentation parameters apply only for networks
with L2 topology.";
}
description
"Configuration parameters for L2 at the node
level.";
uses l2t:l2-node-attributes;
}
augment "/nw-s:networks/nw-s:network/nt-s:link" {
when '../nw-s:network-types/l2t-s:l2-topology' {
description
"Augmentation parameters apply only for networks
with L2 topology.";
}
description
"Augments L2 topology link information.";
uses l2t:l2-link-attributes;
}
augment "/nw-s:networks/nw-s:network/nw-s:node/"
+ "nt-s:termination-point" {
when '../../nw-s:network-types/l2t-s:l2-topology' {
description
"Augmentation parameters apply only for networks
with L2 topology.";
}
description
"Augments L2 topology termination point information.";
uses l2t:l2-termination-point-attributes;
}
/*
* Notifications
*/
notification l2-node-event {
description
"Notification event for L2 node.";
leaf event-type {
type l2t:l2-network-event-type;
description
"Event type.";
}
uses nw-s:node-ref;
uses l2t:l2-network-type;
uses l2t:l2-node-attributes;
}
notification l2-link-event {
description
"Notification event for a an L2 link.";
leaf event-type {
type l2t:l2-network-event-type;
description
"Event type.";
}
uses nt-s:link-ref;
uses l2t:l2-network-type;
uses l2t:l2-link-attributes;
}
notification l2-termination-point-event {
description
"Notification event for L2 termination point.";
leaf event-type {
type l2t:l2-network-event-type;
description
"Event type.";
}
uses nt-s:tp-ref;
uses l2t:l2-network-type;
uses l2t:l2-termination-point-attributes;
}
}
<CODE ENDS>
Appendix B. An Example
This section contains an example of an instance data tree in JSON
encoding [RFC7951]. The example instantiates "ietf-l2-topology" for
the topology that is depicted in the following diagram. There are
three nodes: D1, D2, and D3. D1 has three termination points: 1-0-1,
1-2-1, and 1-3-1. D2 has three termination points as well: 2-1-1,
2-0-1, and 2-3-1. D3 has two termination points: 3-1-1 and 3-2-1.
For termination point 1-0-1, it provides lag support and has two
member link termination points: 1-0-1-1,1-0-1-2. 1-0-1-1 and 1-0-1-2. In addition,
there are six links, two between each pair of nodes, nodes with one going in
each direction.
+------------+ +------------+
| D1 | | D2 |
1-0-1-1 /-\ /-\ /-\ /-\
<--------->| | 1-0-1 | |---------------->| | 2-1-1 | |
1-0-1-2 | | 1-2-1 | |<----------------| | 2-0-1 | |
<--------> \-/ 1-3-1 \-/ \-/ 2-3-1 \-/
| /----\ | | /----\ |
+---| |---+ +---| |---+
\----/ \----/
A | A |
| | | |
| | | |
| | +------------+ | |
| | | D3 | | |
| | /-\ /-\ | |
| +----->| | 3-1-1 | |-------+ |
+---------| | 3-2-1 | |<---------+
\-/ \-/
| |
+------------+
Figure 2. 2: A Network Topology Example
The corresponding instance data tree is depicted below:
{
"ietf-network:networks": {
"network": [
{
"network-id": "l2-topo-example",
"node": [
{
"node-id": "D1",
"ietf-network-topology:termination-point": [
{
"tp-id": "1-0-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:d0",
"lag": true,
"member-link-tp": [
"1-0-1-1",
"1-0-1-2"
]
}
},
{
"tp-id": "1-0-1-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:d3"
}
},
{
"tp-id": "1-0-1-2",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:d4"
}
},
{
"tp-id": "1-2-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:d1"
}
},
{
"tp-id": "1-3-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:d2"
}
}
],
"ietf-l2-topology:l2-node-attributes": {
"management-address": [
"192.0.2.1",
"2001:db8:0:1::"
]
}
},
{
"node-id": "D2",
"ietf-network-topology:termination-point": [
{
"tp-id": "2-0-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:e0"
}
},
{
"tp-id": "2-1-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:e1"
}
},
{
"tp-id": "2-3-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:e2"
}
}
],
"ietf-l2-topology:l2-node-attributes": {
"management-address": [
"192.0.2.2",
"2001:db8:0:2::"
]
}
},
{
"node-id": "D3",
"ietf-network-topology:termination-point": [
{
"tp-id": "3-1-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:f0"
}
},
{
"tp-id": "3-2-1",
"ietf-l2-topology:l2-termination-point-attributes": {
"mac-address": "00:00:5e:00:53:f1"
}
}
],
"ietf-l2-topology:l2-node-attributes": {
"management-address": [
"192.0.2.3",
"2001:db8:0:3::"
]
}
}
],
"ietf-network-topology:link": [
{
"link-id": "D1,1-2-1,D2,2-1-1",
"source": {
"source-node": "D1",
"source-tp": "1-2-1"
},
"destination": {
"dest-node": "D2",
"dest-tp": "2-1-1"
},
"ietf-l2-topology:l2-link-attributes": {
"rate": "1000"
}
},
{
"link-id": "D2,2-1-1,D1,1-2-1",
"source": {
"source-node": "D2",
"source-tp": "2-1-1"
},
"destination": {
"dest-node": "D1",
"dest-tp": "1-2-1"
},
"ietf-l2-topology:l2-link-attributes": {
"rate": "1000"
}
},
{
"link-id": "D1,1-3-1,D3,3-1-1",
"source": {
"source-node": "D1",
"source-tp": "1-3-1"
},
"destination": {
"dest-node": "D3",
"dest-tp": "3-1-1"
},
"ietf-l2-topology:l2-link-attributes": {
"rate": "1000"
}
},
{
"link-id": "D3,3-1-1,D1,1-3-1",
"source": {
"source-node": "D3",
"source-tp": "3-1-1"
},
"destination": {
"dest-node": "D1",
"dest-tp": "1-3-1"
},
"ietf-l2-topology:l2-link-attributes": {
"rate": "1000"
}
},
{
"link-id": "D2,2-3-1,D3,3-2-1",
"source": {
"source-node": "D2",
"source-tp": "2-3-1"
},
"destination": {
"dest-node": "D3",
"dest-tp": "3-2-1"
},
"ietf-l2-topology:l2-link-attributes": {
"rate": "1000"
}
},
{
"link-id": "D3,3-2-1,D2,2-3-1",
"source": {
"source-node": "D3",
"source-tp": "3-2-1"
},
"destination": {
"dest-node": "D2",
"dest-tp": "2-3-1"
},
"ietf-l2-topology:l2-link-attributes": {
"rate": "1000"
}
}
]
}
]
}
}
Acknowledgements
The authors would like to acknowledge the comments and suggestions
received from Susan Hares, Alia Atlas, Juergen Schoenwaelder, Mach
Chen, Alexander Clemm, Sriganesh Kini, Oscar Gonzalez de Dios, Stig
Venaas, Christian Huitema, Meral Shirazipour, Benjamin Kaduk, and Don
Fedyk.
Many thanks to Ladislav Lhotka for the yang-doctors review.
Authors' Addresses
Jie Dong
Huawei
Huawei Campus, Campus
No. 156 Beiqing Rd.
Beijing
100095
China
Email: jie.dong@huawei.com
Xiugang Wei
Huawei
Huawei Campus, Campus
No. 156 Beiqing Rd.
Beijing
100095
China
Email: weixiugang@huawei.com
Qin Wu
Huawei
101 Software Avenue, Avenue
Yuhua District
Nanjing
210012
China
Email: bill.wu@huawei.com
Mohamed Boucadair
Orange
Rennes 35000
France
Email: mohamed.boucadair@orange.com
Anders Liu
Tecent
Yinke Building
38 Haidian St, St
Haidian District
Beijing
100080
China
Email: andersliu@tencent.com