BFD
Internet Engineering Task Force (IETF) S. Pallagatti, Ed.
Internet-Draft
Request for Comments: 8971 VMware
Intended status:
Category: Informational G. Mirsky, Ed.
Expires: April 29, 2021
ISSN: 2070-1721 ZTE Corp.
S. Paragiri
Individual Contributor
V. Govindan
M. Mudigonda
Cisco
October 26,
December 2020
BFD
Bidirectional Forwarding Detection (BFD) for VXLAN
draft-ietf-bfd-vxlan-16 Virtual eXtensible Local
Area Network (VXLAN)
Abstract
This document describes the use of the Bidirectional Forwarding
Detection (BFD) protocol in point-to-point Virtual eXtensible Local
Area Network (VXLAN) tunnels used to form an overlay network.
Status of This Memo
This Internet-Draft document is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents valid
approved by the IESG are candidates for a maximum any level of six months Internet
Standard; see Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 29, 2021.
https://www.rfc-editor.org/info/rfc8971.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Conventions Used in this This Document . . . . . . . . . . . . . . 3
2.1. Acronyms . . . . . . . . . . . . . . . . . . . . . . . . 3 Abbreviations
2.2. Requirements Language . . . . . . . . . . . . . . . . . . 4
3. Deployment . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Use of the Management VNI . . . . . . . . . . . . . . . . . . 5
5. BFD Packet Transmission over VXLAN Tunnel . . . . . . . . . . 6
6. Reception of BFD Packet from VXLAN Tunnel . . . . . . . . . . 8
7. Echo BFD . . . . . . . . . . . . . . . . . . . . . . . . . . 8
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
9. Security Considerations . . . . . . . . . . . . . . . . . . . 9
10. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 9
11. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 9
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 10
12.1.
10.1. Normative References . . . . . . . . . . . . . . . . . . 10
12.2. Informational
10.2. Informative References . . . . . . . . . . . . . . . . 10
Acknowledgments
Contributors
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 11
1. Introduction
"Virtual eXtensible Local Area Network" (VXLAN) Network (VXLAN)" [RFC7348] provides an
encapsulation scheme that allows the building of an overlay network
by decoupling the address space of the attached virtual hosts from
that of the network.
One use of VXLAN is in data centers interconnecting virtual machines
(VMs) of a tenant. VXLAN addresses the requirements of the Layer 2
and Layer 3 data center data-center network infrastructure in the presence of VMs
in a multi-tenant environment by providing a Layer 2 overlay scheme
on a Layer 3 network [RFC7348]. Another use is as an encapsulation
for Ethernet VPN [RFC8365].
This document is written assuming the use of VXLAN for virtualized
hosts and refers to VMs and VXLAN Tunnel End Points (VTEPs) in
hypervisors. However, the concepts are equally applicable to non-
virtualized hosts attached to VTEPs in switches.
In the absence of a router in the overlay, a VM can communicate with
another VM only if they are on the same VXLAN segment. VMs are
unaware of VXLAN tunnels as tunnels, because a VXLAN tunnel is terminated on a
VTEP. VTEPs are responsible for encapsulating and decapsulating
frames exchanged among VMs.
The ability to monitor path continuity, continuity -- i.e., perform proactive
continuity check (CC) for point-to-point (p2p) VXLAN tunnels, tunnels -- is
important. The asynchronous mode of BFD, as defined in [RFC5880], is
used to monitor a p2p VXLAN tunnel.
In the case where a Multicast Service Node (MSN) (as described in
Section 3.3 of [RFC8293]) participates in VXLAN, the mechanisms
described in this document apply and can, therefore, be used to test
the continuity of the path between the source NVE Network Virtualization
Endpoint (NVE) and the MSN.
This document describes the use of the Bidirectional Forwarding
Detection (BFD) protocol to enable monitoring continuity of the path
between VXLAN VTEPs that are performing as Network Virtualization Endpoints, VNEs, and/or between the
source NVE and a replicator MSN using a Management
VNI VXLAN Network
Identifier (VNI) (Section 4). All other uses of the specification to
test toward other VXLAN endpoints are out of the scope.
2. Conventions Used in this This Document
2.1. Acronyms
BFD Abbreviations
BFD: Bidirectional Forwarding Detection
CC
CC: Continuity Check
p2p Point-to-point
MSN
FCS: Frame Check Sequence
MSN: Multicast Service Node
NVE
NVE: Network Virtualization Endpoint
VFI
p2p: Point-to-point
VFI: Virtual Forwarding Instance
VM
VM: Virtual Machine
VNI
VNI: VXLAN Network Identifier (or VXLAN Segment ID)
VTEP
VTEP: VXLAN Tunnel End Point
VXLAN
VXLAN: Virtual eXtensible Local Area Network
2.2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Deployment
Figure 1 illustrates the a scenario with two servers, servers: each of them hosting two
VMs. The servers host VTEPs that terminate two VXLAN tunnels with VXLAN Network Identifier (VNI)
VNI number 100 and 200 200, respectively. Separate BFD sessions can be
established between the VTEPs (IP1 and IP2) for monitoring each of
the VXLAN tunnels (VNI 100 and 200). Using a BFD session to monitor
a set of VXLAN VNIs between the same pair of VTEPs might help to
detect and localize problems caused by misconfiguration. An
implementation that supports this specification MUST be able to
control the number of BFD sessions that can be created between the
same pair of VTEPs. This method is applicable whether the VTEP is a
virtual or physical device.
+------------+-------------+
| Server 1 |
| +----+----+ +----+----+ |
| |VM1-1 | |VM1-2 | |
| |VNI 100 | |VNI 200 | |
| | | | | |
| +---------+ +---------+ |
| VTEP (IP1) |
+--------------------------+
|
| +-------------+
| | Layer 3 |
+---| Network |
+-------------+
|
+-----------+
|
+------------+-------------+
| VTEP (IP2) |
| +----+----+ +----+----+ |
| |VM2-1 | |VM2-2 | |
| |VNI 100 | |VNI 200 | |
| | | | | |
| +---------+ +---------+ |
| Server 2 |
+--------------------------+
Figure 1: Reference VXLAN Domain
At the same time, a service layer service-layer BFD session may be used between the
tenants of VTEPs IP1 and IP2 to provide end-to-end fault management
(this management;
this use case is outside the scope of this document). document. In such a case,
for VTEPs, the BFD Control packets of that session are
indistinguishable from data packets.
For BFD Control packets encapsulated in VXLAN (Figure 2), the inner
destination IP address SHOULD be set to one of the loopback addresses
from 127/8 range for IPv4 or to one of IPv4-mapped IPv6 loopback
addresses from ::ffff:127.0.0.0/104 range for IPv6.
4. Use of the Management VNI
In most cases, a single BFD session is sufficient for the given VTEP
to monitor the reachability of a remote VTEP, regardless of the
number of VNIs. BFD control messages MUST be sent using the
Management VNI VNI, which acts as the as control and management channel
between VTEPs. An implementation MAY support operating BFD on
another (non-Management) VNI VNI, although the implications of this are
outside the scope of this document. The selection of the VNI number
of the Management VNI MUST be controlled through a management plane.
An implementation MAY use VNI number 1 as the default value for the
Management VNI. All VXLAN packets received on the Management VNI
MUST be processed locally and MUST NOT be forwarded to a tenant.
5. BFD Packet Transmission over VXLAN Tunnel
BFD packets MUST be encapsulated and sent to a remote VTEP as
explained in this section. Implementations SHOULD ensure that the
BFD packets follow the same forwarding path as VXLAN data packets
within the sender system.
BFD packets are encapsulated in VXLAN as described below. The VXLAN
packet format is defined in Section 5 of [RFC7348]. The value in the
VNI field of the VXLAN header MUST be set to the value selected as
the Management VNI. The Outer outer IP/UDP and VXLAN headers MUST be
encoded by the sender sender, as defined in [RFC7348].
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Outer Ethernet Header ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Outer IPvX Header ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Outer UDP Header ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ VXLAN Header ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Inner Ethernet Header ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Inner IPvX Header ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Inner UDP Header ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ BFD Control Packet ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Outer Ethernet FCS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: VXLAN Encapsulation of BFD Control Packet
The BFD packet MUST be carried inside the inner Ethernet frame of the
VXLAN packet. The choice of Destination MAC destination Media Access Control (MAC)
and Destination destination IP addresses for the inner Ethernet frame MUST ensure
that the BFD Control packet is not forwarded to a tenant but is
processed locally at the remote VTEP. The inner Ethernet frame
carrying the BFD Control packet- packet has the following format:
Ethernet Header:
Destination MAC: A Management VNI, which does not have any
tenants, will have no dedicated MAC address for decapsulated
traffic. The value (TBD1) 00-52-02 SHOULD be used in this field.
Source MAC: MAC address associated with the originating VTEP.
Ethertype: This is set to 0x0800 if the inner IP header is IPv4, IPv4
and
is set to 0x86DD if the inner IP header is IPv6.
IP header:
Destination IP: This IP address MUST NOT be of one of tenant's IP
addresses. The IP address SHOULD be selected from the range
127/8 for IPv4, for IPv6 - IPv4 and from the range ::ffff:127.0.0.0/104. ::ffff:127.0.0.0/104 for
IPv6. Alternatively, the destination IP address MAY be set to
VTEP's IP address.
Source IP: IP address of the originating VTEP.
TTL or Hop Limit: MUST be set to 255 255, in accordance with
[RFC5881].
The fields of the destination UDP header port is set to 3784 and the fields of the BFD
Control packet are encoded as specified in [RFC5881].
6. Reception of BFD Packet from VXLAN Tunnel
Once a packet is received, the VTEP MUST validate the packet. If the
packet is received on the management Management VNI and is identified as a BFD
control
Control packet addressed to the VTEP, and then the packet can be
processed further. Processing of BFD control Control packets received on
non-management a
non-Management VNI is outside the scope of this specification.
The received packet's inner IP payload is then validated according to
Sections 4 and 5 in [RFC5881].
7. Echo BFD
Support for echo BFD is outside the scope of this document.
8. IANA Considerations
IANA is requested to assign has assigned a single MAC address to of the value TBD1 00-52-02 from the
"Unassigned (small allocations)" block of the "IANA Unicast 48-bit
MAC Address" Addresses" registry from as follows: the
"Unassigned (small allocations)" block. The Usage "Usage" field will be is "BFD for VXLAN" with a Reference field of
VXLAN". The "Reference" is this document.
9. Security Considerations
Security issues discussed in [RFC5880], [RFC5881], and [RFC7348]
apply to this document.
This document recommends using an address from the Internal internal host
loopback addresses 127/8 range for IPv4 IPv4, or an IP4-mapped IPv6
loopback address from the ::ffff:127.0.0.0/104 range for IPv6 IPv6, as the
destination IP address in the inner IP header. Using such an address
prevents the forwarding of the encapsulated BFD control message by a
transient node node, in case the VXLAN tunnel is broken as according to broken, in accordance
with [RFC1812].
| A router SHOULD NOT forward, except over a loopback interface,
| any packet that has a destination address on network 127. A
| router MAY have a switch that allows the network manager to
| disable these checks. If such a switch is provided, it MUST
| default to performing the checks.
The use of IPv4-mapped IPv6 addresses has the same property as using
the IPv4 network 127/8, moreover, 127/8. Moreover, the IPv4-mapped IPv6 addresses addresses'
prefix is not advertised in any routing protocol.
If the implementation supports establishing multiple BFD sessions
between the same pair of VTEPs, there SHOULD be a mechanism to
control the maximum number of such sessions that can be active at the
same time.
10. Contributors
Reshad Rahman
rrahman@cisco.com
Cisco
11. Acknowledgments
Authors would like to thank Jeff Haas of Juniper Networks for his
reviews and feedback on this material.
Authors would also like to thank Nobo Akiya, Marc Binderberger,
Shahram Davari, Donald E. Eastlake 3rd, Anoop Ghanwani, Dinesh Dutt,
Joel Halpern, and Carlos Pignataro for the extensive reviews and the
most detailed and constructive comments.
12. References
12.1.
10.1. Normative References
[RFC1812] Baker, F., Ed., "Requirements for IP Version 4 Routers",
RFC 1812, DOI 10.17487/RFC1812, June 1995,
<https://www.rfc-editor.org/info/rfc1812>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC5880] Katz, D. and D. Ward, "Bidirectional Forwarding Detection
(BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010,
<https://www.rfc-editor.org/info/rfc5880>.
[RFC5881] Katz, D. and D. Ward, "Bidirectional Forwarding Detection
(BFD) for IPv4 and IPv6 (Single Hop)", RFC 5881,
DOI 10.17487/RFC5881, June 2010,
<https://www.rfc-editor.org/info/rfc5881>.
[RFC7348] Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger,
L., Sridhar, T., Bursell, M., and C. Wright, "Virtual
eXtensible Local Area Network (VXLAN): A Framework for
Overlaying Virtualized Layer 2 Networks over Layer 3
Networks", RFC 7348, DOI 10.17487/RFC7348, August 2014,
<https://www.rfc-editor.org/info/rfc7348>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
12.2. Informational
10.2. Informative References
[RFC8293] Ghanwani, A., Dunbar, L., McBride, M., Bannai, V., and R.
Krishnan, "A Framework for Multicast in Network
Virtualization over Layer 3", RFC 8293,
DOI 10.17487/RFC8293, January 2018,
<https://www.rfc-editor.org/info/rfc8293>.
[RFC8365] Sajassi, A., Ed., Drake, J., Ed., Bitar, N., Shekhar, R.,
Uttaro, J., and W. Henderickx, "A Network Virtualization
Overlay Solution Using Ethernet VPN (EVPN)", RFC 8365,
DOI 10.17487/RFC8365, March 2018,
<https://www.rfc-editor.org/info/rfc8365>.
Acknowledgments
The authors would like to thank Jeff Haas of Juniper Networks for his
reviews and feedback on this material.
The authors would also like to thank Nobo Akiya, Marc Binderberger,
Shahram Davari, Donald E. Eastlake 3rd, Anoop Ghanwani, Dinesh Dutt,
Joel Halpern, and Carlos Pignataro for the extensive reviews and the
most detailed and constructive comments.
Contributors
Reshad Rahman
Cisco
Email: rrahman@cisco.com
Authors' Addresses
Santosh Pallagatti (editor)
VMware
Email: santosh.pallagatti@gmail.com
Greg Mirsky (editor)
ZTE Corp.
Email: gregimirsky@gmail.com
Sudarsan Paragiri
Individual Contributor
Email: sudarsan.225@gmail.com
Vengada Prasad Govindan
Cisco
Email: venggovi@cisco.com
Mallik Mudigonda
Cisco
Email: mmudigon@cisco.com