wdiff rfc9032.original rfc9032.txt

6tisch Working Group

Internet Engineering Task Force (IETF) D. Dujovne
Internet-Draft Dujovne, Ed.
Request for Comments: 9032 Universidad Diego Portales
Intended status:
Category: Standards Track M. Richardson
Expires: 24 August 2020
ISSN: 2070-1721 Sandelman Software Works
21 February 2020

IEEE 802.15.4 Information Element encapsulation
May 2021

Encapsulation of 6TiSCH Join and Enrollment Information
draft-ietf-6tisch-enrollment-enhanced-beacon-14 Elements

Abstract

In TSCH the Time-Slotted Channel Hopping (TSCH) mode of IEEE STD Std 802.15.4,
opportunities for broadcasts are limited to specific times and
specific channels. Routers in a Time-
Slotted Channel Hopping (TSCH) TSCH network transmit Enhanced
Beacon (EB) frames to announce the presence of the network. This
document provides a mechanism by which additional information
critical for new nodes (pledges) and long sleeping long-sleeping nodes may be
carried within the
Enhanced Beacon EB in order to conserve use of broadcast
opportunities.

Status of This Memo

This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents an Internet Standards Track document.

This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.

Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

This Internet-Draft will expire on 24 August 2020.
https://www.rfc-editor.org/info/rfc9032.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info)
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Use of BCP 14 Terminology . . . . . . . . . . . . . . . . 2
1.2. Layer-2 Layer 2 Synchronization . . . . . . . . . . . . . . . . . 3
1.3. Layer-3 synchronization: Layer 3 Synchronization: IPv6 Router Solicitations and
Advertisements . . . . . . . . . . . . . . . . . . . . . 3
1.4. Layer-2 Layer 2 Selection . . . . . . . . . . . . . . . . . . . . 4
2. Protocol Definition . . . . . . . . . . . . . . . . . . . . . 5
3. Security Considerations . . . . . . . . . . . . . . . . . . . 8
4. Privacy Considerations . . . . . . . . . . . . . . . . . . . 9
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 9
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.1.
6.1. Normative References . . . . . . . . . . . . . . . . . . 9
7.2.
6.2. Informative References . . . . . . . . . . . . . . . . . 10
Acknowledgments
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 11

1. Introduction

[RFC7554] describes the use of the Time-Slotted Channel Hopping
(TSCH) mode of [ieee802154]. [IEEE.802.15.4].

In TSCH mode of IEEE STD Std 802.15.4, opportunities for broadcasts are
limited to specific times and specific channels. Routers in a Time-
Slotted Channel Hopping (TSCH) TSCH
network transmit Enhanced Beacon (EB) frames during broadcast slots
in order to announce the time and channel schedule.

This document defines a new IETF Information Element (IE) subtype to
place into the Enhanced Beacon (EB) EB to provide join and enrollment information to
prospective pledges in a more efficient way.

The following sub-sections subsections explain the problem being solved, which
justify
justifies carrying the join and enrollement enrollment information in the EB.

1.1. Use of BCP 14 Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.

Other terminology can be found in [I-D.ietf-6tisch-architecture] in
section 2.1. Section 2.1 of [RFC9030].

1.2. Layer-2 Layer 2 Synchronization

As explained in section 6 Section 4.5.2 of [RFC8180], the Enhanced Beacon (EB) EB has a number of
purposes: it carries synchronization of information such as the Absolute
Slot Number (ASN) and Join Metric, carrying Metric and identifiers for the timeslot
template identifier,
carrying and the channel hopping sequence identifier, sequence, and indicating it indicates the TSCH SlotFrame.
slotframe.

An EB announces the existence of a TSCH network, network and of the nodes already
joined to that network. Receiving an EB allows a Joining Node
(pledge) to learn about the network and synchronize to synchronize with it.

The EB may also be used as a means for a node already part of the
network to re-synchronize resynchronize [RFC7554].

There are a limited number of timeslots designated as broadcast slots
by each router in the network. Considering 10ms 10 ms slots and a slot-
frame
slotframe length of 100, these slots are rare and could result in
only 1 slot per second for broadcasts, which needs to be used for the
beacon. Additional broadcasts for Router Advertisements (RA), (RA) or
Neighbor Discovery (ND) could be even more scarce.

1.3. Layer-3 synchronization: Layer 3 Synchronization: IPv6 Router Solicitations and
Advertisements

At layer Layer 3, [RFC4861] defines a mechanism by which nodes learn about
routers by receiving multicast Router Advertisements (RA). RAs. If no RA is received within a
set time, then a Router Solicitation (RS) may be transmitted as a
multicast, to which an RA will be received, usually unicast.

Although [RFC6775] reduces the amount of multicast necessary to do for
address resolution via Neighbor Solicitation (NS) messages, it still
requires multicast of either RAs or RSes. This is an expensive
operation for two reasons: there are few multicast timeslots for
unsolicited RAs; and if a pledge node does not receive an RA, and
decides to transmit an RS, a broadcast aloha Aloha slot (see [RFC7554]
section A.5) Appendix A.5
of [RFC7554]) is consumed with unencrypted traffic. [RFC6775]
already allows for a unicast reply to such an RS.

This is a particularly acute issue for the join process for the
following reasons:

1. Use of a multicast slot by even a non-malicious unauthenticated
node for a Router Solicitation (RS) may overwhelm that time slot. timeslot.

2. It may require many seconds of on-time before a new pledge
receives a Router Advertisement (RA) that it can use.

3. A new pledge may have to receive many Enhanced Beacons (EB) EBs before it can pick an
appropriate network and/or closest Join
Assistant Proxy to attach to. If
it must remain in the receive state for an RA as well as find the Enhanced Beacon (EB),
EB, then the process may take dozens of seconds, even minutes for
each enrollment attempt that it needs to make.

1.4. Layer-2 Layer 2 Selection

In a complex Low-power and Lossy Networks Network (LLN), multiple LLNs may be
connected together by backbone routers ( technology Backbone Routers (technology such as
[I-D.ietf-6lo-backbone-router]),
[RFC8929]), resulting in an area that is serviced by multiple multiple,
distinct Layer-2 Layer 2 instances. These are called Personal Area Networks (PAN).
(PANs). Each instance will have a separate
Layer-2 Layer 2 security profile, profile
and will be distinguished by a different PANID. The PANID is part of
the [ieee802154] layer-2 header: Layer 2 header as defined in [IEEE.802.15.4]: it is a 16-bit
value which that is chosen to be unique, and it contributes context to the layer-2
Layer 2 security mechanisms. The PANID provides a context similar to
the ESSID does Extended Service Set ID (ESSID) in 802.11 networking, networking and can be conceived
of in a
considered similar fashion as to the 802.3 ethernet Ethernet VLAN tag in that it provides
context for all layer-2 Layer 2 addresses.

A device which that is already enrolled in a network may find after a long
sleep that it needs to resynchronize to with the Layer 2 network. The
device's enrollment keys that it has will be specific to a PANID, but it the device
may have more than one set of keys. Such a device may wish to
connect to a PAN that is experiencing less congestion, congestion or which that has a shalower
([RFC6550])
shallower Routing Protocol for LLNs (RPL) tree. tree [RFC6550]. It may
even observe PANs for which it does not have keys, but for which is it
believes it may have credentials that would allow it to join.

In order to identify which PANs are part of the same backbone
network, the network ID is introduced in this extension. PANs that
are part of the same backbone will be configured to use the same
network ID. For [RFC6550] RPL networks, networks [RFC6550], configuration of the network
ID can be done with an a configuration option, which is the subject of
future work.

In order to provide some input to the choice of which PAN to use, the
PAN priority field has been added. This lists the relative priority
for the PAN among different PANs. Every Enhanced Beacon EB from a given PAN will
likely have the same PAN priority. Determination of the the PAN priority
is the subject of future work; but it is expected that it will be
calculated by an algorithm in the 6LBR, 6LoWPAN Border Router (6LBR),
possibly involving communication between 6LBRs over the backbone
network.

The [RFC6550] parent selection process [RFC6550] can only operate within a
single PAN, PAN because it depends upon receiving RPL DIO messages from
all available parents. As part of the PAN selection process, the
device may wish to know how deep in the LLN mesh it will be if it
joins a particular PAN, and the rank priority field provides an
estimation of what the rank of each announcer is. announcer's rank. Once the device synchronizes to
with a particular PAN's TSCH schedule then schedule, it may receive DIOs that are
richer in their diversity than this value. How The use of this value will be used in
practice is the subject of future research, and the interpretation of
this value of the structure is considered experimental.

2. Protocol Definition

[RFC8137] creates a registry for new IETF IE subtypes. This document
allocates a new subtype.

The new IE subtype structure is as follows. As explained in
[RFC8137]
[RFC8137], the length of the Sub-Type Content subtype content can be calculated from
the container, so no length information is necessary.

1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TBD-XXX 2 |R|P| res | proxy prio | rank priority |
+-+-+-+-+-+-+-+-+-+-------------+-------------+-----------------+
| pan PAN priority | |
+---------------+ +
| Join Proxy Interface-ID Interface ID |
+ (present if P=1) +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+ +
| network ID |
+ variable length, up to 16 bytes +
~ ~
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+

Figure 1: IE subtype structure Subtype Structure

res: reserved Reserved bits MUST be ignored upon receipt, receipt and SHOULD be set to
0 when sending.

R: The Router Advertisement RA R-flag is set if the sending node will act as a Router router for
host-only nodes relying on stateless address auto-configuration
(SLAAC) to get their global IPv6 address. Those hosts MUST send a
unicast Router Solicitation RS message in order to receive a an RA with the Prefix
Information Option.

In most cases, every node sending a beacon will set this flag, and
in a typical mesh, this will be every single node. When this bit
is not set, it might indicate that this node may be under
provisioned,
provisioned or that it may have no additional slots for additional
nodes. This could make this node more interesting to an attacker.

P: If the Proxy Address P-flag is set, then the Join Proxy Interface
ID bit field is present. Otherwise, it is not provided.

This bit only indicates if another part of the structure is
present, and it has little security or privacy impact.

proxy priority prio (proxy prio): priority): This field indicates the willingness of
the sender to act as join proxy. a Join Proxy. Lower value indicates greater
willingness to act as a Join Proxy as described in
[I-D.ietf-6tisch-minimal-security]. [RFC9031].
Values range from 0x00 (most willing) to 0x7e (least willing). A
priority of 0x7f indicates that the announcer should never be
considered as a viable
enrollment proxy. Join Proxy. Only unenrolled pledges look
at this value.

Lower values in this field indicate that the transmitter may have
more capacity to handle unencrypted traffic. A higher value may
indicate that the transmitter is low on neighbor cache entries, entries or
other resources. Ongoing work such as
[I-D.ietf-roll-enrollment-priority] [NETWORK-ENROLLMENT]
documents one way to set this field.

rank priority: The rank "priority" priority is set by the IPv6 LLN Router (6LR) which
that sent the beacon and is an indication of how willing this 6LR
is to serve as an a RPL [RFC6550] parent [RFC6550] within a particular network
ID. Lower values indicate more willingness, and higher values
indicate less willingness. This value is calculated by each 6LR
according to algorithms specific to the routing metrics used by
the RPL ([RFC6550]). [RFC6550]. The exact process is a subject of significant
research work. It will typically be calculated from the RPL rank,
and it may include some modifications based upon current number of children,
children or the number of neighbor cache entries available.
Pledges MUST ignore this value. It helps enrolled devices only to
compare connection points.

An attacker can use this value to determine which nodes are
potentially more interesting. Nodes which that are less willingness willing to be
parents likely have more traffic, and an attacker could use this
information to determine which nodes would be more interesting to
attack or disrupt.

pan

PAN priority: The pan PAN priority is a value set by the Destination-
Oriented Directed Acyclic Graph (DODAG) root (see [RFC6550],
typically,
typically the 6LBR) to indicate the relative priority of this LLN
compared to those with different PANIDs that the operator might
control. This value may be used as part of the enrollment
priority, but typically it is used by devices which that have already
enrolled,
enrolled and need to determine which PAN to pick when resuming
from a long sleep. Unenrolled pledges MAY consider this value
when selecting a PAN to join. Enrolled devices MAY consider this
value when looking for an eligible parent device. Lower values
indicate a higher more willingness to accept new nodes.

An attacker can use this value, along with the observed PANID in
the Beacon EB to determine which PANIDs have more network resources, and
may have more interesting traffic.

Join Proxy Interface ID: If the P bit is set, then 64 bits (8 bytes)
of address are present. This field provides the Interface ID
(IID) of the Link-Local link-local address of the Join Proxy. The associated
prefix is well-known as fe80::/64. If this field is not present,
then IID is derived from the layer-2 Layer 2 address of the sender as per
SLAAC ([RFC4662]). [RFC4862].

This field communicates the Interface ID IID bits that should be used for this
node's layer-3 Layer 3 address, if it should not be derived from the layer-2 Layer
2 address. Communication with the Join Proxy occurs in the clear.
This field avoids the need for an additional service-
discovery service-discovery
process for the case where the L3 Layer 3 address is not derived from
the L2 Layer 2 address. An attacker will see both L2 Layer 2 and L3 Layer
3 addresses, so this field provides no new information.

network ID: This is a variable length field, up to 16-bytes in size
that uniquely identifies this network, potentially among many
networks that are operating in the same frequencies in overlapping
physical space. The length of this field can be calculated as
being whatever is left in the Information Element. IE.

In a 6tisch 6TiSCH network, where RPL [RFC6550] is used as the mesh
routing protocol, the network ID can be constructed from a
truncated SHA256 SHA-256 hash of the prefix (/64) of the network. This
will be done by the RPL DODAG root and communicated by the RPL
Configuration Option payloads, so it is not calculated more than
once. This is just a suggestion for a default algorithm: it may
be set in any convenience convenient way that results in a non-identifing non-identifying
value. In some LLNs where multiple PANIDs may lead to the same
management device (the Join Registrar/Coordinator - JRC), (JRC)), then a
common value that is the same across all the PANs MUST be
configured. Pledges that see the same networkID network ID will not waste
time attempting to enroll multiple times with the same network
that
when the network has multiple attachment points.

If the network ID is derived as suggested, then it will be an
opaque, seemingly random value, value and will not directly reveal any
information about the network. An attacker can match this value
across many transmissions to map the extent of a network beyond
what the PANID might already provide.

3. Security Considerations

All of the contents of this Information Element IE are transmitted in the clear. The
content of the Enhanced Beacon EB is not encrypted. This is a restriction in the
cryptographic architecture of the 802.15.4 mechanism. In order to
decrypt or do integrity checking of
layer-2 Layer 2 frames in TSCH, the TSCH Absolute Slot Number (ASN)
ASN is needed. The Enhanced Beacon EB provides the ASN to new (and long-
sleeping) long-sleeping)
nodes.

The sensitivity of each field is described within the description of
each field.

The Enhanced Beacon EB is authenticated at the layer-2 Layer 2 level using 802.15.4
mechanisms using the network-wide keying material. Nodes
which that are
enrolled will have the network-wide keying material and can validate
the beacon.

Pledges which that have not yet enrolled are unable to authenticate the
beacons,
beacons and will be forced to temporarily take the contents on faith.
After enrollment, a newly enrolled node will be able to return to the
beacon and validate it.

In addition to the enrollment and join information described in this
document, the Enhanced Beacon EB contains a description of the TSCH schedule to be
used by the transmitter of this packet. The schedule can provide an
attacker with a list of channels and frequencies on which
communication will occur. Knowledge of this can help an attacker to
more efficiently jam communications, although there is future work
being considered to make some of the schedule less visible.
Encrypting the schedule does not prevent an attacker from jamming,
but rather increases the energy cost of doing that jamming.

4. Privacy Considerations

The use of a network ID may reveal information about the network.
The use of a SHA256 SHA-256 hash of the DODAGID (see [RFC6550]), rather than
using the DODAGID itself directly provides some privacy for the the
addresses used within the network, as the DODAGID is usually the IPv6
address of the root of the RPL mesh.

An interloper with a radio sniffer would be able to use the network
ID to map out the extent of the mesh network.

5. IANA Considerations

IANA is asked to assign a new number TBD-XXX from Registry has assigned the following value in the "IEEE Std 802.15.4 IETF
IE Subtype IDs" registry, as defined by [RFC8137].

This entry should be called 6tisch-Join-Info, and should refer to
this document.

+=======+==================+===========+
| Value Subtype-ID | Subtype ID | Reference
---- ---------- -----------
TBD-XXX 6tisch-Join-Inbfo [this document] |
+=======+==================+===========+
| 2 | 6tisch-Join-Info | RFC 9032 |
+-------+------------------+-----------+

Table 1

6. Acknowledgements

Thomas Watteyne provided extensive editorial comments on the
document. Carles Gomez Montenegro generated a detailed review of the
document at WGLC. Tim Evens provided a number of useful editorial
suggestions.

7. References

7.1.

6.1. Normative References

[BCP14] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.

[I-D.ietf-6tisch-minimal-security]
Vucinic, M., Simon, J., Pister, K., and M. Richardson,
"Constrained Join Protocol (CoJP) for 6TiSCH", Work in
Progress, Internet-Draft, draft-ietf-6tisch-minimal-
security-15, 10 December 2019, <http://www.ietf.org/
internet-drafts/draft-ietf-6tisch-minimal-security-
15.txt>.

[ieee802154]
IEEE standard for Information Technology, .,

[IEEE.802.15.4]
IEEE, "IEEE Std.

802.15.4, Part. 15.4: Wireless Medium Access Control (MAC)
and Physical Layer (PHY) Specifications Standard for Low-Rate Wireless Personal Area Networks", 2015,
<http://standards.ieee.org/findstds/
standard/802.15.4-2015.html>. IEEE
Standard 802.15.4-2015, DOI 10.1109/IEEESTD.2016.7460875,
April 2016,
<https://ieeexplore.ieee.org/document/7460875>.

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.

[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
DOI 10.17487/RFC4861, September 2007,
<https://www.rfc-editor.org/info/rfc4861>.

[RFC6775] Shelby, Z., Ed., Chakrabarti, S., Nordmark, E., and C.
Bormann, "Neighbor Discovery Optimization for IPv6 over
Low-Power Wireless Personal Area Networks (6LoWPANs)",
RFC 6775, DOI 10.17487/RFC6775, November 2012,
<https://www.rfc-editor.org/info/rfc6775>.

[RFC8137] Kivinen, T. and P. Kinney, "IEEE 802.15.4 Information
Element for the IETF", RFC 8137, DOI 10.17487/RFC8137, May
2017, <https://www.rfc-editor.org/info/rfc8137>.

[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.

7.2.

[RFC9031] Vučinić, M., Ed., Simon, J., Pister, K., and M.
Richardson, "Constrained Join Protocol (CoJP) for 6TiSCH",
RFC 9031, DOI 10.17487/RFC9031, May 2021,
<https://www.rfc-editor.org/info/rfc9031>.

6.2. Informative References

[I-D.ietf-6lo-backbone-router]

[NETWORK-ENROLLMENT]
Richardson, M., Jadhav, R. A., Thubert, P., Perkins, C., and E. Levy-Abegnoli, "IPv6
Backbone Router", Work in Progress, Internet-Draft, draft-
ietf-6lo-backbone-router-17, 20 February 2020,
<http://www.ietf.org/internet-drafts/draft-ietf-6lo-
backbone-router-17.txt>.

[I-D.ietf-6tisch-architecture]
Thubert, P., "An Architecture for IPv6 over the TSCH mode
of IEEE 802.15.4", Work in Progress, Internet-Draft,
draft-ietf-6tisch-architecture-28, 29 October 2019,
<http://www.ietf.org/internet-drafts/draft-ietf-6tisch-
architecture-28.txt>.

[I-D.ietf-roll-enrollment-priority]
Richardson, M., "Enabling secure network enrollment H. She,
"Controlling Secure Network Enrollment in RPL networks",
Work in Progress, Internet-Draft, draft-ietf-
roll-enrollment-priority-00, 16 September 2019,
<http://www.ietf.org/internet-drafts/draft-ietf-roll-
enrollment-priority-00.txt>.

[RFC4662] Roach, A. B., Campbell, B., draft-ietf-roll-
enrollment-priority-04, 7 February 2021,
<https://tools.ietf.org/html/draft-ietf-roll-enrollment-
priority-04>.

[RFC4862] Thomson, S., Narten, T., and J. Rosenberg, "A Session
Initiation Protocol (SIP) Event Notification Extension for
Resource Lists", T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4662, 4862,
DOI 10.17487/RFC4662, August
2006, <https://www.rfc-editor.org/info/rfc4662>. 10.17487/RFC4862, September 2007,
<https://www.rfc-editor.org/info/rfc4862>.

[RFC6550] Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J.,
Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur,
JP., and R. Alexander, "RPL: IPv6 Routing Protocol for
Low-Power and Lossy Networks", RFC 6550,
DOI 10.17487/RFC6550, March 2012,
<https://www.rfc-editor.org/info/rfc6550>.

[RFC7554] Watteyne, T., Ed., Palattella, M., and L. Grieco, "Using
IEEE 802.15.4e Time-Slotted Channel Hopping (TSCH) in the
Internet of Things (IoT): Problem Statement", RFC 7554,
DOI 10.17487/RFC7554, May 2015,
<https://www.rfc-editor.org/info/rfc7554>.

[RFC8180] Vilajosana, X., Ed., Pister, K., and T. Watteyne, "Minimal
IPv6 over the TSCH Mode of IEEE 802.15.4e (6TiSCH)
Configuration", BCP 210, RFC 8180, DOI 10.17487/RFC8180,
May 2017, <https://www.rfc-editor.org/info/rfc8180>.

[RFC8929] Thubert, P., Ed., Perkins, C.E., and E. Levy-Abegnoli,
"IPv6 Backbone Router", RFC 8929, DOI 10.17487/RFC8929,
November 2020, <https://www.rfc-editor.org/info/rfc8929>.

[RFC9030] Thubert, P., Ed., "An Architecture for IPv6 over the Time-
Slotted Channel Hopping Mode of IEEE 802.15.4 (6TiSCH)",
RFC 9030, DOI 10.17487/RFC9030, May 2021,
<https://www.rfc-editor.org/info/rfc9030>.

Acknowledgments

Thomas Watteyne provided extensive editorial comments on the
document. Carles Gomez Montenegro generated a detailed review of the
document at Working Group Last Call. Tim Evens provided a number of
useful editorial suggestions.

Authors' Addresses

Diego Dujovne (editor)
Universidad Diego Portales
Escuela de Informatica Informática y Telecomunicaciones, Telecomunicaciones
Av. Ejercito Ejército 441
Santiago, Region
Santiago
Región Metropolitana
Chile

Phone: +56 (2) 676-8121
Email: diego.dujovne@mail.udp.cl

Michael Richardson
Sandelman Software Works

Email: mcr+ietf@sandelman.ca