Network Working Group A.
Internet Engineering Task Force (IETF) T. Przygienda, Ed.
Internet-Draft
Request for Comments: 9377 Juniper
Category: Experimental C. Bowers
Intended status: Experimental Juniper
Expires: 8 June 2023
ISSN: 2070-1721 Individual
Y. Lee
Comcast
A. Sharma
Individual
R. White
Akamai
5 December 2022
April 2023
IS-IS Flood Reflection
draft-ietf-lsr-isis-flood-reflection-12
Abstract
This document describes a backward-compatible, optional IS-IS
extension that allows the creation of IS-IS flood reflection
topologies. Flood reflection permits topologies in which L1
IS-IS Level 1 (L1) areas provide transit forwarding transit-forwarding for L2 IS-IS Level 2
(L2) areas using all available L1 nodes internally. It accomplishes
this by creating L2 flood reflection adjacencies within each L1 area.
Those adjacencies are used to flood L2 LSPDUs Link State Protocol Data Units
(LSPs) and are used in the L2 SPF Shortest Path First (SPF) computation.
However, they are not ordinarily utilized for forwarding within the
flood reflection cluster. This arrangement gives the L2 topology
significantly better scaling properties than traditionally prevalently used flat
designs. As an additional benefit, only those routers directly
participating in flood reflection are required to support the
feature. This allows for incremental deployment of scalable L1
transit areas in an existing, previously flat network design, without
the necessity of upgrading all routers in the network.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
Status of This Memo
This Internet-Draft document is submitted in full conformance with the
provisions of BCP 78 not an Internet Standards Track specification; it is
published for examination, experimental implementation, and BCP 79.
Internet-Drafts are working documents
evaluation.
This document defines an Experimental Protocol for the Internet
community. This document is a product of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft the IETF
community. It has received public review and has been approved for
publication by the Internet Engineering Steering Group (IESG). Not
all documents valid approved by the IESG are candidates for a maximum any level of six months
Internet Standard; see Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 8 June 2023.
https://www.rfc-editor.org/info/rfc9377.
Copyright Notice
Copyright (c) 2022 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info)
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Revised BSD License text as described in Section 4.e of the
Trust Legal Provisions and are provided without warranty as described
in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Conventions Used in This Document
2.1. Terminology
2.2. Requirements Language
3. Further Details . . . . . . . . . . . . . . . . . . . . . . . 9
4. Encodings . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1. Flood Reflection TLV . . . . . . . . . . . . . . . . . . 10
4.2. Flood Reflection Discovery Sub-TLV . . . . . . . . . . . 11
4.3. Flood Reflection Discovery Tunnel Type Sub-Sub-TLV . . . 12
4.4. Flood Reflection Adjacency Sub-TLV . . . . . . . . . . . 14
4.5. Flood Reflection Discovery . . . . . . . . . . . . . . . 15
4.6. Flood Reflection Adjacency Formation . . . . . . . . . . 16
5. Route Computation . . . . . . . . . . . . . . . . . . . . . . 16
5.1. Tunnel-Based Deployment . . . . . . . . . . . . . . . . . 17
5.2. No-Tunnel Deployment . . . . . . . . . . . . . . . . . . 17
6. Redistribution of Prefixes . . . . . . . . . . . . . . . . . 17
7. Special Considerations . . . . . . . . . . . . . . . . . . . 18
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 18
8.1. New IS-IS TLV Codepoint . . . . . . . . . . . . . . . . . 19
8.2. Sub TLVs Sub-TLVs for IS-IS Router CAPABILITY TLV . . . . . . . . 19
8.3. Sub-sub TLVs Sub-Sub-TLVs for Flood Reflection Discovery sub-TLV . . . 19 Sub-TLV
8.4. Sub TLVs Sub-TLVs for TLVs Advertising Neighbor Information . . . 19
9. Security Considerations . . . . . . . . . . . . . . . . . . . 20
10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 20
11. References . . . . . . . . . . . . . . . . . . . . . . . . . 20
11.1. Informative References . . . . . . . . . . . . . . . . . 20
11.2.
10.1. Normative References . . . . . . . . . . . . . . . . . . 21
10.2. Informative References
Acknowledgements
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 22
1. Introduction
This section introduces the problem space and outlines the solution.
Some of the terms may be unfamiliar to readers without extensive IS-
IS background; for such readers a glossary readers, the terminology is provided in
Section 2. 2.1.
Due to the inherent properties of link-state protocols protocols, the number of
IS-IS routers within a flooding domain is limited by processing and
flooding overhead on each node. While that number can be maximized
by well-written implementations and techniques such as exponential
back-offs,
backoffs, IS-IS will still reach a saturation point where no further
routers can be added to a single flooding domain. In some L2
backbone deployment scenarios, this limit presents a significant
challenge.
The traditional standard approach to increasing the scale of an IS-IS deployment
is to break it up into multiple L1 flooding domains and a single L2
backbone. This works well for designs where an L2 backbone connects
L1 access topologies, but it is limiting where a single, flat L2
domain is supposed to span large number of routers. In such
scenarios, an alternative approach could be to consider multiple L2
flooding domains that are connected together via L1 flooding domains.
In other words, L2 flooding domains are connected by "L1/L2 lanes"
through the L1 areas to form a single L2 backbone again.
Unfortunately, in its simplest implementation, this requires the
inclusion of most, or all, of the transit L1 routers as L1/L2 to
allow traffic to flow along optimal paths through those transit
areas. Consequently, such an approach fails to reduce the number of
L2 routers involved and and, with that that, fails to increase the scalability
of the L2 backbone as well.
Figure 1 is an example of a network where a topologically rich L1
area is used to provide transit between six different L2-only routers
(R1-R6). Note that the six L2-only routers do not have connectivity
to one another over L2 links. To take advantage of the abundance of
paths in the L1 transit area, all the intermediate systems could be
placed into both L1 and L2, but this essentially combines the
separate L2 flooding domains into a single one, triggering again triggering the
maximum L2 scale limitation we try were trying to address in first place.
+====+ +=======+ +=======+ +======-+ +====+
I R1 I I R10 +-------------+ R20 +---------------+ R30 I I R4 I
I L2 +--+ L1/L2 I I L1 I I L1/L2 +--+ L2 I
I I I + +--+ I +------------+ I I I
+====+ ++====+=+ | +===+===+ | +=+==+=++ +====+
| | | | | | |
| | | | | +-----------+ |
| +-------+ | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
+====+ ++=====-+ | | +===+===+--+ | +======++ +====+
I R2 I I R11 I | | I R21 I | I R31 I I R5 I
I L2 +--+ L1/L2 +-------------+ L1 +---------------+ L1/L2 +--+ L2 I
I I I I | | I I | +-------+ I I I
+====+ ++=====-+ | | ++==+==++ | | +======++ +====+
| | | | | | | | |
| +---------------+ | | | | | |
| | | | | | | | |
| | +----------------+ | +-----------------+ |
| | | | | | | | |
+====+ ++=+==+=+ +-------+===+===+-----+ | ++=====++ +====+
I R3 I I R12 I I R22 I | + R32 I I R6 I
I L2 +--+ L1/L2 I I L1 +-------+ I L1/L2 +--+ L2 I
I I I +-------------+ +---------------+ I I I
+====+ +=======+ +=======+ +=======+ +====+
Figure 1: Example Topology of L1 with L2 Borders
A more effective solution would allow to reduce the reduction of the number of
links and routers exposed in L2, while still utilizing the full L1
topology when forwarding through the network.
[RFC8099] describes Topology Transparent Zones (TTZ) for OSPF. The
TTZ mechanism represents a group of OSPF routers as a full mesh of
adjacencies between the routers at the edge of the group. A similar
mechanism could be applied to IS-IS as well. However, a full mesh of
adjacencies between edge routers (or L1/L2 nodes) significantly
limits the practically achievable scale of the resulting topology.
The topology in Figure 1 has 6 six L1/L2 nodes. Figure 2 illustrates a
full mesh of L2 adjacencies between the 6 six L1/L2 nodes, resulting in
(5 * 6)/2 = 15 L2 adjacencies. In a somewhat larger topology
containing 20 L1/L2 nodes, the number of L2 adjacencies in a full
mesh rises to 190.
+----+ +-------+ +-------------------------------+-------+ +----+
| R1 | | R10 | | | R30 | | R4 |
| L2 +--+ L1/L2 +------------------------------------+ L1/L2 +--+ L2 |
| | | | | | | | |
+----+ ++-+-+--+-+ | +-+--+---++ +----+
| | | | | | | |
| +----------------------------------------------+ |
| | | | | | | |
| +-----------------------------------+ | | | |
| | | | | | | |
| +----------------------------------------+ | |
| | | | | | | |
+----+ ++-----+- | | | | -----+-++ +----+
| R2 | | R11 | | | | | | R31 | | R5 |
| L2 +--+ L1/L2 +------------------------------------+ L1/L2 +--+ L2 |
| | | | | | | | | | | |
+----+ ++------+------------------------------+ | | +----+-++ +----+
| | | | | | | |
| | | | | | | |
| +-------------------------------------------+ |
| | | | | | | |
| | | | +----------+ |
| | | | | | | |
| | | | +-----+ | |
| | | | | | | |
+----+ ++----+-+-+ | +-+-+--+-++ +----+
| R3 | | R12 | | L2 adjacency | R32 | | R6 |
| L2 +--+ L1/L2 +------------------------------------+ L1/L2 +--+ L2 |
| | | | | | | | |
+----+ +-------+----+ +-------+ +----+
Figure 2: Example topology represented Topology Represented in L2 with a full mesh Full Mesh of
L2 adjacencies Adjacencies between L1/L2 nodes Nodes
BGP, as specified in [RFC4271], faced a similar scaling problem,
which has been solved in many networks by deploying BGP route
reflectors [RFC4456]. We note that BGP route reflectors do not
necessarily have to be in the forwarding path of the traffic. This
non-congruity of forwarding and control path for BGP route reflectors
allows the control plane to scale independently of the forwarding
plane and represents an interesting degree of freedom in network
architecture.
We propose in this document a similar solution for IS-IS and call it
"flood reflection" in a fashion analogous to "route reflection". A
simple example of what a flood reflector control plane approach would
look like is shown in Figure 3, where router R21 plays the role of a
flood reflector. Each L1/L2 ingress/egress router builds a tunnel to
the flood reflector, and an L2 adjacency is built over each tunnel.
In this solution, we need only 6 six L2 adjacencies, instead of the 15
needed for a full mesh. In a somewhat larger topology containing 20
L1/L2 nodes, this solution requires only 20 L2 adjacencies, instead
of the 190 needed for a full mesh. Multiple flood reflectors can be
used, allowing the network operator to balance between resilience,
path utilization, and state in the control plane. The resulting L2
adjacency scale is R*n, where R is the number of flood reflectors
used and n is the number of L1/L2 nodes. This compares quite
favorably with n*(n-1)/2 L2 adjacencies required in a topologically
fully meshed L2 solution.
+----+ +-------+ +-------+ +----+
| R1 | | R10 | | R30 | | R4 |
| L2 +--+ L1/L2 +--------------+ +-----------------+ L1/L2 +--+ L2 |
| | | | L2 adj | | L2 adj | | | |
+----+ +-------+ over | | over +-------+ +----+
tunnel | | tunnel
+----+ +-------+ +--+---+--+ +-------+ +----+
| R2 | | R11 | | R21 | | R31 | | R5 |
| L2 +--+ L1/L2 +-----------+ L1/L2 +--------------+ L1/L2 +--+ L2 |
| | | | L2 adj | flood | L2 adj | | | |
+----+ +-------+ over |reflector| over +-------+ +----+
tunnel +--+---+--+ tunnel
+----+ +-------+ | | +-------+ +----+
| R3 | | R12 +--------------+ +-----------------+ R32 | | R6 |
| L2 +--+ L1/L2 | L2 adj L2 adj | L1/L2 +--+ L2 |
| | | | over over | | | |
+----+ +-------+ tunnel tunnel +-------+ +----+
Figure 3: Example topology represented Topology Represented in L2 with L2 adjacencies Adjacencies
from each Each L1/ L2 node Node to a single flood reflector Single Flood Reflector
As illustrated in Figure 3, when R21 plays the role of flood
reflector, it provides L2 connectivity among all of the previously
disconnected L2 islands by reflooding all L2 LSPDUs. Link State Protocol Data
Unit (LSPs). At the same time, R20 and R22 in Figure 1 remain
L1-only routers. L1-only routers and L1-only links are not visible
in L2. In this manner, the flood reflector allows us to provide L2
control plane connectivity in a manner more scalable than a flat L2
domain.
As described so far, the solution illustrated in Figure 3 relies only
on currently standardized IS-IS functionality. Without new
functionality, however, the data traffic will traverse only R21.
This will unnecessarily create a bottleneck at R21 since there is
still available capacity in the paths crossing the L1-only routers
R20 and R22 in Figure 1.
Hence, additional functionality is compulsory to allow the L1/L2 edge
nodes (R10-12 and R30-32 in Figure 3) to recognize that the L2
adjacency to R21 should not be used for forwarding. The L1/L2 edge
nodes should forward traffic that would normally be forwarded over
the L2 adjacency to R21 over L1 links instead. This would allow the
forwarding within the L1 area to use the L1-only nodes and links
shown in Figure 1 as well. It allows networks to be built that use the entire
forwarding capacity of the L1 areas, areas to be built, while at the same
time introducing it introduces control plane scaling benefits that are provided
by L2 flood reflectors.
It is expected that deployment at scale, and suitable time in
operation, will provide sufficient evidence to either make put this
extension into a standard, Standards Track document or suggest necessary
modifications to accomplish this. that.
The remainder of this document defines the remaining extensions
necessary for a complete flood reflection solution:
* It defines a special 'flood "flood reflector adjacency' adjacency" built for the
purpose of reflecting flooding information. These adjacencies
allow 'flood reflectors' "flood reflectors" to participate in the IS-IS control plane
without necessarily being used in the forwarding plane.
Maintenance of such adjacencies is a purely local operation on the
L1/L2 ingress and flood reflectors; it does not require replacing
or modifying any routers not involved in the reflection process.
In practical deployments, it is far less tricky to just upgrade
the routers involved in flood reflection rather than have a flag
day for the whole IS-IS domain.
* It specifies an (optional) full mesh of tunnels between the L1/L2
ingress routers, ideally load-balancing across all available L1
links. This harnesses all forwarding paths between the L1/L2 edge
nodes without injecting unneeded state into the L2 flooding domain
or creating 'choke points' "choke points" at the 'flood reflectors' "flood reflectors" themselves.
The specification is agnostic as to the tunneling technology used
but provides enough information for automatic establishment of
such tunnels if desired. The discussion of IS-IS adjacency
formation and/or liveness discovery on such tunnels is outside the
scope of this specification and is largely a choice of the
underlying implementation. A solution without tunnels is also
possible by introducing the correct scoping of reachability
information between the levels. This is described in more detail
later.
* Finally, the this document defines support of reflector redundancy and
an (optional) way to auto-discover and annotate flood reflector
adjacencies on advertisements. Such additional information in
link advertisements allows L2 nodes outside the L1 area to
recognize a flood reflection cluster and its adjacencies.
2. Glossary Conventions Used in This Document
2.1. Terminology
The following terms are used in this document.
ISIS Level-1
IS-IS Level 1 and Level-2 areas, mostly Level 2 areas (mostly abbreviated as L1 and L2:
Traditional ISIS L2):
IS-IS concepts whereas where a routing domain has two "levels" with a
single L2 area being the "backbone" that connects multiple L1
areas for scaling and reliability purposes. IS-IS architecture
prescribes a routing domain with two "levels" where a single L2
area functions as the "backbone" that connects multiple L1 areas
amongst themselves for scaling and reliability purposes. In
traditional ISIS such
architecture, L2 can be used as transit for L1-L1 traffic carried from
one L1 area to another, but L1 areas themselves cannot be used for
that purpose since because the L2 level must be a single "connected"
entity, and all traffic exiting an L1 area flows along L2 routers
until it the traffic arrives at the destination L1 area. area itself.
Flood Reflector:
Node configured to connect in L2 only to flood reflector clients
and to reflect (reflood) IS-IS L2 LSPs amongst them.
Flood Reflector Client:
Node configured to build Flood Reflector Adjacencies to Flood
Reflectors,
Reflectors and to build normal adjacencies to other clients and L2
nodes not participating in flood reflection.
Flood Reflector Adjacency:
IS-IS L2 adjacency where one end is a Flood Reflector Client Client, and
the other other, a Flood Reflector, and the two Reflector. Both have the same Flood Reflector
Cluster ID.
Flood Reflector Cluster:
Collection of clients and flood reflectors configured with the
same cluster identifier.
Tunnel-Based Deployment:
Deployment where Flood Reflector Clients build a partial or full
mesh of tunnels in L1 to "shortcut" forwarding of L2 traffic
through the cluster.
No-Tunnel Deployment:
Deployment where Flood Reflector Clients redistribute L2
reachability into L1 to allow forwarding through the cluster
without underlying tunnels.
Tunnel Endpoint:
An endpoint that allows the establishment of a bi-directional bidirectional
tunnel carrying IS-IS control traffic or or, alternately, serves as
the origin of such a tunnel.
L1 shortcut:
A tunnel established between two clients that is visible in L1
only that and is used as a
next-hop, i.e. next hop, i.e., to carry data traffic in
tunnel-based deployment mode.
Hot-Potato Routing:
In the context of this document, a routing paradigm where L2->L1
routes are less preferred than L2 routes [RFC5302].
2.2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Further Details
Several considerations should be noted in relation to such a flood
reflection mechanism.
First, this the flood reflection mechanism allows multi-area IS-IS
deployments to scale without any major modifications in the IS-IS
implementation on most of the nodes deployed in the network.
Unmodified (traditional) (standard) L2 routers will compute reachability across the
transit L1 area using the flood reflector adjacencies. (In this
document, the term "standard" refers to IS-IS as specified in
[ISO10589].)
Second, the flood reflectors are not required to participate in
forwarding traffic through the L1 transit area. These flood
reflectors can be hosted on virtual devices outside the forwarding
topology.
Third, astute readers will realize that flooding reflection may cause
the use of suboptimal paths. This is similar to the BGP route
reflection suboptimal routing problem described in
[ID.draft-ietf-idr-bgp-optimal-route-reflection-28]. [RFC9107]. The L2
computation determines the egress L1/L2 and and, with that that, can create
illusions of ECMP where there is none, none; and in certain scenarios scenarios, the
L2 computation can lead to an L1/L2 egress which that is not globally
optimal. This represents a straightforward instance of the trade-off
between the amount of control plane state and the optimal use of
paths through the network that are often encountered when aggregating
routing information.
One possible solution to this problem is to expose additional
topology information into the L2 flooding domains. In the example
network given, links from router R10 to router R11 can be exposed
into L2 even when R10 and R11 are participating in flood reflection.
This information would allow the L2 nodes to build 'shortcuts' "shortcuts" when
the L2 flood reflected flood-reflected part of the topology looks more expensive to
cross distance wise. distance-wise.
Another possible variation is for an implementation to approximate
with use the tunnel
cost to approximate the cost of the underlying topology.
Redundancy can be achieved by configuring multiple flood reflectors
in a an L1 area. Multiple flood reflectors do not need any
synchronization mechanisms amongst themselves, except standard IS-IS
flooding and database maintenance procedures.
4. Encodings
4.1. Flood Reflection TLV
The Flood Reflection TLV is a top-level TLV that MUST appear in L2
IIHs (IS-IS Hello) on all Flood Reflection Adjacencies. The Flood
Reflection TLV indicates the flood reflector cluster (based on Flood
Reflection Cluster ID) that a given router is configured to
participate in. It also indicates whether the router is configured
to play the role of either flood reflector or flood reflector client.
The Flood Reflection Cluster ID and flood reflector roles advertised
in the IIHs are used to ensure that flood reflector adjacencies are
only formed between a flood reflector and flood reflector client, client and
that the Flood Reflection Cluster IDs match. The Flood Reflection
TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |C| RESERVED Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Flood Reflection Cluster ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sub-TLVs ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: 161
Length: The length, in octets, of the following fields.
C (Client): This bit is set to indicate that the router acts as a
flood reflector client. When this bit is NOT set, the router acts
as a flood reflector. On a given router, the same value of the
C-bit MUST be advertised across all interfaces advertising the
Flood Reflection TLV in IIHs.
RESERVED:
Reserved: This field is reserved for future use. It MUST be set to
0 when sent and MUST be ignored when received.
Flood Reflection Cluster ID: Flood Reflection Cluster Identifier. The same arbitrary 32-bit value MUST be
assigned to all of the flood reflectors and flood reflector
clients in the same L1 area. The value MUST be unique across
different L1 areas within the IGP domain. In case of violation of
those rules rules, multiple L1 areas may become a single cluster cluster, or a
single area may split in flood reflection sense sense, and several mechanisms
mechanisms, such as auto-discovery of
tunnels tunnels, may not work
correctly. On a given router, the same value of the Flood
Reflection Cluster ID MUST be advertised across all interfaces
advertising the Flood Reflection TLV in IIHs. When a router
discovers that a node is using more than a single Cluster IDs
based on its advertised TLVs and IIHs, the node MAY log such
violations subject to rate limiting. rate-limiting. This implies that a flood
reflector MUST NOT participate in more than a single L1 area. In
case of Cluster ID value of 0, the TLV containing it MUST be
ignored.
Sub-TLVs: Optional sub-TLVs.
Sub-TLVs (Optional Sub-TLVs): For future extensibility, the format
of the Flood Reflection TLV allows for the possibility of
including optional sub-TLVs. No sub-TLVs of the Flood Reflection
TLV are defined in this document.
The Flood Reflection TLV SHOULD NOT appear more than once in an IIH.
A router receiving one or more Flood Reflection TLVs in the same IIH
MUST use the values in the first TLV TLV, and it SHOULD log such
violations subject to rate limiting. rate-limiting.
4.2. Flood Reflection Discovery Sub-TLV
The Flood Reflection Discovery sub-TLV is advertised as a sub-TLV of
the IS-IS Router Capability TLV-242, TLV 242, defined in [RFC7981]. The Flood
Reflection Discovery sub-TLV is advertised in L1 and L2 LSPs with
area flooding scope in order to enable the auto-discovery of flood
reflection capabilities. The Flood Reflection Discovery sub-TLV has
the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |C| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Flood Reflection Cluster ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: 161
Length: The length, in octets, of the following fields.
C (Client): This bit is set to indicate that the router acts as a
flood reflector client. When this bit is NOT set, the router acts
as a flood reflector.
RESERVED:
Reserved: This field is reserved for future use. It MUST be set to
0 when sent and MUST be ignored when received.
Flood Reflection Cluster ID: The Flood Reflection Cluster Identifier
is the same as that defined in the Flood Reflection TLV in
Section 4.1 and obeys the same rules.
The Flood Reflection Discovery sub-TLV SHOULD NOT appear more than
once in TLV 242. A router receiving one or more Flood Reflection
Discovery sub-TLVs in TLV 242 MUST use the values in the first sub-
TLV of the lowest numbered fragment fragment, and it SHOULD log such
violations subject to rate limiting. rate-limiting.
4.3. Flood Reflection Discovery Tunnel Type Sub-Sub-TLV
Flood Reflection Discovery Tunnel Type sub-sub-TLV is advertised
optionally as a sub-sub-TLV of the Flood Reflection Discovery Sub-
TLV, defined in Section 4.2. It allows the automatic creation of L2
tunnels to be used as flood reflector adjacencies and L1 shortcut
tunnels. The Flood Reflection Tunnel Type sub-sub-TLV has the
following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-------------+-+
| Type | Length | Reserved |F|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Tunnel Encapsulation Attribute |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: 161
Length: The length, in octets, of zero or more of the following
fields.
Reserved: SHOULD be 0 on transmission and MUST be ignored on
reception.
F Flag: When set set, indicates flood reflection tunnel endpoint, when endpoint. When
clear, indicates possible L1 shortcut tunnel endpoint.
Tunnel Encapsulation Attribute: Carries encapsulation type and
further attributes necessary for tunnel establishment as defined
in [RFC9012]. In context of this attribute attribute, the protocol Type sub-
TLV
sub-TLV as defined in [RFC9012] MAY be included to ensure proper
encapsulation of IS-IS frames. In case such a sub-TLV is included
and the F flag is set (i.e. (i.e., the resulting tunnel is a flood
reflector adjacency) adjacency), this sub-TLV MUST include a type that allows
to carry encapsulated IS-IS frames. Furthermore, such tunnel type
MUST be able to transport IS-IS frames of size up to
`originatingL2LSPBufferSize`.
"originatingL2LSPBufferSize".
A flood reflector receiving Flood Reflection Discovery Tunnel Type
sub-sub-TLVs in Flood Reflection Discovery sub-TLV with F flag set
(i.e.
(i.e., the resulting tunnel is a flood reflector adjacency) SHOULD
use one or more of the specified tunnel endpoints to automatically
establish one or more tunnels that will serve as a flood reflection
adjacency(-ies)
adjacency and/or adjacencies to the clients advertising the
endpoints.
A flood reflection client receiving one or more Flood Reflection
Discovery Tunnel Type sub-sub-TLVs in Flood Reflection Discovery sub-
TLV with F flag clear (i.e. (i.e., the resulting tunnel is used to support
tunnel-based mode) from other leaves MAY use one or more of the
specified tunnel endpoints to automatically establish one or more
tunnels that will serve as L1 tunnel shortcuts to the clients
advertising the endpoints.
In case of automatic flood reflection adjacency tunnels and in case
IS-IS adjacencies are being formed across L1 shortcuts shortcuts, all the
aforementioned rules in Section 4.5 apply as well.
Optional address validation procedures as defined in [RFC9012] MUST
be disregarded.
It remains to be observed that automatic tunnel discovery is an
optional part of the specification and can be replaced or mixed with
statically configured tunnels for either flood reflector adjacencies
and/or and
tunnel-based shortcuts. Specific implementation details how both
mechanisms interact are specific to an implementation and mode of
operation and are outside the scope of this document.
Flood reflector adjacencies rely on IS-IS L2 liveliness procedures.
In case of L1 shortcuts shortcuts, the mechanism used to ensure liveliness and
tunnel integrity are outside the scope of this document.
4.4. Flood Reflection Adjacency Sub-TLV
The Flood Reflection Adjacency sub-TLV is advertised as a sub-TLV of
TLVs 22, 23, 25, 141, 222, and 223 (the "TLVs Advertising Neighbor
Information"). Its presence indicates that a given adjacency is a
flood reflector adjacency. It is included in L2 area scope flooded
LSPs. The Flood Reflection Adjacency sub-TLV has the following
format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |C| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Flood Reflection Cluster ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: 161
Length: The length, in octets, of the following fields.
C (Client): This bit is set to indicate that the router advertising
this adjacency is a flood reflector client. When this bit is NOT
set, the router advertising this adjacency is a flood reflector.
RESERVED:
Reserved: This field is reserved for future use. It MUST be set to
0 when sent and MUST be ignored when received.
Flood Reflection Cluster ID: The Flood Reflection Cluster Identifier
is the same as that defined in the Flood Reflection TLV in
Section 4.1 and obeys the same rules.
The Flood Reflection Adjacency sub-TLV SHOULD NOT appear more than
once in a given TLV. A router receiving one or more Flood Reflection
Adjacency sub-TLVs in a TLV MUST use the values in the first sub-TLV
of the lowest numbered fragment fragment, and it SHOULD log such violations
subject to rate limiting. rate-limiting.
4.5. Flood Reflection Discovery
A router participating in flood reflection as client or reflector
MUST be configured as an L1/L2 router. It MAY originate the Flood
Reflection Discovery sub-TLV with area flooding scope in L1 and L2.
Normally, all routers on the edge of the L1 area (those having
traditional
standard L2 adjacencies) will advertise themselves as flood reflector
clients. Therefore, a flood reflector client will have both traditional standard
L2 adjacencies and flood reflector L2 adjacencies.
A router acting as a flood reflector MUST NOT form any traditional standard L2
adjacencies except with flood reflector clients. It will be an L1/L2
router only by virtue of having flood reflector L2 adjacencies. A
router desiring to act as a flood reflector MAY advertise itself as
such using the Flood Reflection Discovery sub-TLV in L1 and L2.
A given flood reflector or flood reflector client can only
participate in a single cluster, as determined by the value of its
Flood Reflection Cluster ID and should disregard other routers' TLVs
for flood reflection purposes if the cluster ID is not matching.
Upon reception of Flood Reflection Discovery sub-TLVs, a router
acting as flood reflector SHOULD initiate a tunnel towards each flood
reflector client with which it shares a Flood Reflection Cluster ID ID,
using one or more of the tunnel encapsulations provided with F flag
is set. The L2 adjacencies formed over such tunnels MUST be marked
as flood reflector adjacencies. If the client or reflector has a
direct L2 adjacency with the according remote side side, it SHOULD use it
instead of instantiating a tunnel.
In case the optional auto-discovery mechanism is not implemented or
enabled
enabled, a deployment MAY use statically configured tunnels to create
flood reflection adjacencies.
The IS-IS metrics for all flood reflection adjacencies in a cluster
SHOULD be identical.
Upon reception of Flood Reflection Discovery TLVs, a router acting as
a flood reflector client MAY initiate tunnels with L1-only
adjacencies towards any of the other flood reflector clients with
lower router IDs in its cluster using encapsulations with F flag
clear. These tunnels MAY be used for forwarding to improve the load-
balancing characteristics of the L1 area. If the clients have a
direct L2 adjacency adjacency, they SHOULD use it instead of instantiating a
new tunnel.
4.6. Flood Reflection Adjacency Formation
In order to simplify implementation complexity, this document does
not allow the formation of complex hierarchies of flood reflectors
and clients or allow multiple clusters in a single L1 area.
Consequently, all flood reflectors and flood reflector clients in the
same L1 area MUST share the same Flood Reflector Cluster ID.
Deployment of multiple cluster IDs in the same L1 area are outside
the scope of this document.
A flood reflector MUST NOT form flood reflection adjacencies with
flood reflector clients with a different Cluster ID. A flood
reflector MUST NOT form any traditional standard L2 adjacencies.
Flood reflector clients MUST NOT form flood reflection adjacencies
with flood reflectors with a different Cluster ID.
Flood reflector clients MAY form traditional standard L2 adjacencies with flood
reflector clients or nodes not participating in flood reflection.
When two flood reflector clients form a traditional standard L2
adjacency adjacency, the
Cluster IDs are disregarded.
The Flood Reflector Cluster ID and flood reflector roles advertised
in the Flood Reflection TLVs in IIHs are used to ensure that flood
reflection adjacencies that are established meet the above criteria.
On change in either flood reflection role or cluster ID on IIH on the
local or remote side side, the adjacency has to be reset. It is then re-
established if possible.
Once a flood reflection adjacency is established, the flood reflector
and the flood reflector client MUST advertise the adjacency by
including the Flood Reflection Adjacency Sub-TLV in the Extended IS
reachability TLV or MT-ISN Multi-Topology Intermediate System Neighbor (MT-
ISN) TLV.
5. Route Computation
To ensure loop-free routing, the flood reflection client MUST follow
the normal L2 computation to determine L2 routes. This is because
nodes outside the L1 area will generally not be aware that flood
reflection is being performed. The flood reflection clients need to
produce the same result for the L2 route computation as a router not
participating in flood reflection.
5.1. Tunnel-Based Deployment
In the tunnel-based option option, the reflection client, after L2 and L1
computation, MUST examine all L2 routes with flood reflector next-hop
adjacencies. Such next-hops next hops must be replaced by the corresponding
tunnel next-hops next hops to the correct egress nodes of the flood reflection
cluster.
5.2. No-Tunnel Deployment
In case of deployment without underlying tunnels, the necessary L2
routes are distributed into the area, normally as L2->L1 routes. Due
to the rules in Section 4.6 4.6, the computation in the resulting
topology is relatively simple, simple: the L2 SPF from a flood reflector
client is guaranteed to reach the Flood Reflector within a single
hop, and in the following hop hop, it is guaranteed to reach the L2
egress to which it has a forwarding tunnel. All the flood reflector
tunnel nexthops next hops in the according L2 route can hence be removed removed, and
if the L2 route has no other ECMP L2 nexthops, next hops, the L2 route MUST be
suppressed in the RIB by some means to allow the less preferred
L2->L1 route to be used to forward traffic towards the advertising
egress.
In the particular case the client has L2 routes which are not flood
reflected, those will be naturally preferred (such routes normally
"hot-potato" packets out of the L1 area). However However, in the case the
L2 route through the flood reflector egress is "shorter" than such
present non flood reflected L2 routes, routes that are not flood reflected, the node SHOULD
ensure that such routes are suppressed so the L2->L1 towards the
egress still takes preference. Observe that operationally this can
be resolved in a relatively simple way by configuring flood reflector
adjacencies to have a high metric, i.e. i.e., the flood reflector topology
becomes "last
resort" resort," and the leaves will try to "hot-potato" out
the area as fast as possible possible, which is normally the desirable
behavior.
In No-tunnel deployment no-tunnel deployment, all L1/L2 edge nodes MUST be flood
reflection clients.
6. Redistribution of Prefixes
In case of no-tunnel deployment per Section 5.2 5.2, a client that does
not have any L2 flood reflector adjacencies MUST NOT redistribute L2
routes into the cluster.
The L2 prefix advertisements redistributed into an L1 that contains
flood reflectors SHOULD be normally limited to L2 intra-area routes
(as defined in [RFC7775]), [RFC7775]) if the information exists to distinguish
them from other L2 prefix advertisements.
On the other hand, in topologies that make use of flood reflection to
hide the structure of L1 areas while still providing transit transit-
forwarding across them using tunnels, we generally do not need to
redistribute L1 prefix advertisements into L2.
7. Special Considerations
In pathological cases cases, setting the overload bit in L1 (but not in L2)
can partition L1 forwarding, while allowing L2 reachability through
flood reflector adjacencies to exist. In such a case case, a node cannot
replace a route through a flood reflector adjacency with a an L1
shortcut
shortcut, and the client MAY use the L2 tunnel to the flood reflector
for forwarding but in any case it forwarding. In all those cases, the node MUST initiate an alarm
and declare misconfiguration.
A flood reflector with directly L2 attached prefixes should advertise
those in L1 as well since since, based on preference of L1 routes routes, the
clients will not try to use the L2 flood reflector adjacency to route
the packet towards them. A very unlikely corner case can occur when
the flood reflector is reachable via L2 flood reflector adjacency
(due to underlying L1 partition) exclusively, in which case exclusively. In this instance, the
client can use the L2 tunnel to the flood reflector for forwarding
towards those prefixes while it MUST initiate an alarm and declare
misconfiguration.
A flood reflector MUST NOT set the attached bit on its LSPs.
In certain cases where reflectors are attached to the same broadcast
medium, and where some other L2 router, which router that is neither a flood
reflector nor a flood reflector client (a "non-FR router"), router", i.e., a
router not participating in flood reflection) attaches to the same
broadcast medium, flooding between the reflectors in question might
not succeed, potentially partitioning the flood reflection domain.
This could happen specifically in the event that the non-FR router is
chosen as the designated intermediate system
("DIS", Designated Intermediate System (DIS) -- the designated router).
router. Since, per Section 4.6, a flood reflector MUST NOT form an
adjacency with a non-FR router, the flood reflector(s) will not be
represented in the pseudo-node.
To avoid this situation, it is RECOMMENDED that flood reflectors not
be deployed on the same broadcast medium as non-FR routers.
A router discovering such condition MUST initiate an alarm and
declare misconfiguration.
8. IANA Considerations
This document requests allocation for
IANA has assigned the following IS-IS TLVs and
Sub-TLVs, sub-TLVs and requests creation of has
created a new registry.
8.1. New IS-IS TLV Codepoint
This document requests the
The following IS-IS TLV under has been registered in the IS-IS Top-
Level "IS-IS Top-Level
TLV Codepoints registry:: Codepoints" registry:
+=======+==================+=====+=====+=====+=======+
| Value | Name | IIH | LSP | SNP | Purge
----- --------------------------------- --- --- --- ----- |
+=======+==================+=====+=====+=====+=======+
| 161 | Flood Reflection | y | n | n | n |
+-------+------------------+-----+-----+-----+-------+
Table 1: Flood Reflection IS-IS TLV Codepoint
8.2. Sub TLVs Sub-TLVs for IS-IS Router CAPABILITY TLV
This document request the
The following registration has been registered in the "sub-TLVs "IS-IS Sub-TLVs for IS-IS
Router CAPABILITY TLV" registry. registry:
+======+============================+
| Type | Description
---- ----------- |
+======+============================+
| 161 | Flood Reflection Discovery |
+------+----------------------------+
Table 2: IS-IS Router CAPABILITY TLV
8.3. Sub-sub TLVs Sub-Sub-TLVs for Flood Reflection Discovery sub-TLV
This document requests creation of Sub-TLV
IANA has created a new registry named "Sub-sub TLVs "IS-IS Sub-Sub-TLVs for Flood
Reflection Discovery sub-TLV" Sub-TLV" under the "IS-IS TLV Codepoints"
grouping. The Registration Procedures registration procedure for this registry
are is Expert Review,
Review [RFC8126], following the common expert review guidance given
for the grouping.
The range of values in this registry is 0-255. The registry should
be seeded with contains
the following initial registration:
+======+===========================================================+
| Type | Description
---- ----------- |
+======+===========================================================+
| 161 | Flood Reflection Discovery Tunnel Encapsulation Attribute |
+------+-----------------------------------------------------------+
Table 3: IS-IS Sub-Sub-TLVs for Flood Reflection Discovery Sub-TLV
8.4. Sub TLVs Sub-TLVs for TLVs Advertising Neighbor Information
This document requests the
The following registration has been registered in the "IS-IS Sub-
TLVs Sub-TLVs for TLVs
Advertising Neighbor Information" registry. registry;
+======+===========================+====+====+====+=====+=====+=====+
| Type | Description | 22 | 23 | 25 | 141 | 222 | 223
---- -------------------------------- --- --- --- --- --- --- |
+======+===========================+====+====+====+=====+=====+=====+
| 161 | Flood Reflector Adjacency | y | y | n | y | y | y |
| | Adjacency | | | | | | |
+------+---------------------------+----+----+----+-----+-----+-----+
Table 4: IS-IS Sub-TLVs for TLVs Advertising Neighbor Information
9. Security Considerations
This document uses flood reflection tunnels to carry IS-IS control
traffic. If an attacker can inject traffic into such a tunnel, the
consequences could be in (in the most extreme case case) the complete
subversion of the IS-IS level Level 2 information. Therefore, a mechanism
inherent to the tunnel technology should be taken used to prevent such
injection. Since the available security procedures will vary by
deployment and tunnel type, the details of securing tunnels are
beyond the scope of this document.
This document specifies information used to form dynamically
discovered shortcut tunnels. If an attacker were able to hijack the
endpoint of such a tunnel and form an adjacency, it could divert
short-cut
shortcut traffic to itself, placing itself on-path and facilitating
on-path attacks attacks, or it could even completely subvert the IS-IS level Level
2 routing. Therefore, steps should be taken to prevent such capture
by using mechanism inherent to the tunnel type used. Since the
available security procedures will vary by deployment and tunnel
type, the details of securing tunnels are beyond the scope of this
document.
Additionally, the usual IS-IS security mechanisms [RFC5304] SHOULD be
deployed to prevent misrepresentation of routing information by an
attacker in case a tunnel is compromised if and the tunnel itself does
not provide mechanisms strong enough guaranteeing to guarantee the integrity of
the messages exchanged.
10. Acknowledgements
The authors thank Shraddha Hegde, Peter Psenak, Acee Lindem, Robert
Raszuk References
10.1. Normative References
[ISO10589] ISO, "Information technology - Telecommunications and Les Ginsberg
information exchange between systems - Intermediate System
to Intermediate System intra-domain routeing information
exchange protocol for their thorough review and detailed
discussions. Thanks are also extended to Michael Richardson use in conjunction with the protocol
for an
excellent routing directorate review. John Scudder ultimately spent
significant time helping to make providing the document more comprehensible and
coherent.
11. References
11.1. Informative References
[ID.draft-ietf-idr-bgp-optimal-route-reflection-28]
Raszuk et al., R., "BGP Optimal Route Reflection", July
2019, <https://www.ietf.org/id/draft-ietf-idr-bgp-optimal-
route-reflection-28.txt>.
[RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
Border Gateway Protocol 4 (BGP-4)", RFC 4271,
DOI 10.17487/RFC4271, January 2006,
<https://www.rfc-editor.org/info/rfc4271>.
[RFC4456] Bates, T., Chen, E., and R. Chandra, "BGP Route
Reflection: An Alternative to Full Mesh Internal BGP
(IBGP)", RFC 4456, DOI 10.17487/RFC4456, April 2006,
<https://www.rfc-editor.org/info/rfc4456>.
[RFC8099] Chen, H., Li, R., Retana, A., Yang, Y., and Z. Liu, "OSPF
Topology-Transparent Zone", RFC 8099,
DOI 10.17487/RFC8099, February 2017,
<https://www.rfc-editor.org/info/rfc8099>.
11.2. Normative References connectionless-mode network service (ISO
8473)", Second Edition, ISO/IEC 10589:2002, November 2002.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC5302] Li, T., Smit, H., and T. Przygienda, "Domain-Wide Prefix
Distribution with Two-Level IS-IS", RFC 5302,
DOI 10.17487/RFC5302, October 2008,
<https://www.rfc-editor.org/info/rfc5302>.
[RFC5304] Li, T. and R. Atkinson, "IS-IS Cryptographic
Authentication", RFC 5304, DOI 10.17487/RFC5304, October
2008, <https://www.rfc-editor.org/info/rfc5304>.
[RFC7775] Ginsberg, L., Litkowski, S., and S. Previdi, "IS-IS Route
Preference for Extended IP and IPv6 Reachability",
RFC 7775, DOI 10.17487/RFC7775, February 2016,
<https://www.rfc-editor.org/info/rfc7775>.
[RFC7981] Ginsberg, L., Previdi, S., and M. Chen, "IS-IS Extensions
for Advertising Router Information", RFC 7981,
DOI 10.17487/RFC7981, October 2016,
<https://www.rfc-editor.org/info/rfc7981>.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/info/rfc8126>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC9012] Patel, K., Van de Velde, G., Sangli, S., and J. Scudder,
"The BGP Tunnel Encapsulation Attribute", RFC 9012,
DOI 10.17487/RFC9012, April 2021,
<https://www.rfc-editor.org/info/rfc9012>.
10.2. Informative References
[RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
Border Gateway Protocol 4 (BGP-4)", RFC 4271,
DOI 10.17487/RFC4271, January 2006,
<https://www.rfc-editor.org/info/rfc4271>.
[RFC4456] Bates, T., Chen, E., and R. Chandra, "BGP Route
Reflection: An Alternative to Full Mesh Internal BGP
(IBGP)", RFC 4456, DOI 10.17487/RFC4456, April 2006,
<https://www.rfc-editor.org/info/rfc4456>.
[RFC8099] Chen, H., Li, R., Retana, A., Yang, Y., and Z. Liu, "OSPF
Topology-Transparent Zone", RFC 8099,
DOI 10.17487/RFC8099, February 2017,
<https://www.rfc-editor.org/info/rfc8099>.
[RFC9107] Raszuk, R., Ed., Decraene, B., Ed., Cassar, C., Åman, E.,
and K. Wang, "BGP Optimal Route Reflection (BGP ORR)",
RFC 9107, DOI 10.17487/RFC9107, August 2021,
<https://www.rfc-editor.org/info/rfc9107>.
Acknowledgements
The authors thank Shraddha Hegde, Peter Psenak, Acee Lindem, Robert
Raszuk, and Les Ginsberg for their thorough review and detailed
discussions. Thanks are also extended to Michael Richardson for an
excellent routing directorate review. John Scudder ultimately spent
significant time helping to make the document more comprehensible and
coherent.
Authors' Addresses
Tony Przygienda (editor)
Juniper
1137 Innovation Way
Sunnyvale, CA
United States of America
Email: prz@juniper.net
Chris Bowers
Juniper
1137 Innovation Way
Sunnyvale, CA
United States of America
Individual
Email: cbowers@juniper.net chrisbowers.ietf@gmail.com
Yiu Lee
Comcast
1800 Bishops Gate Blvd
Mount Laurel, NJ 08054
United States of America
Email: Yiu_Lee@comcast.com
Alankar Sharma
Individual
Email: as3957@gmail.com
Russ White
Akamai
Email: russ@riw.us