lpwan Working Group
Internet Engineering Task Force (IETF) E. Ramos
Internet-Draft
Request for Comments: 9391 Ericsson
Intended status:
Category: Standards Track A. Minaburo
Expires: 18 June 2023
ISSN: 2070-1721 Acklio
15 December 2022
April 2023
Static Context Header Compression over Narrowband Internet of Things
draft-ietf-lpwan-schc-over-nbiot-15
Abstract
This document describes Static Context Header Compression and
Fragmentation
fragmentation (SCHC) specifications, RFC RFCs 8724 and RFC 8824, in
combination with the 3rd Generation Partnership Project (3GPP) and
the Narrowband Internet of Things (NB-IoT).
This document has two parts. One parts: one normative to specify part that specifies the
use of SCHC over NB-IoT. And NB-IoT and one informational, which informational part that recommends
some values if 3GPP wanted wants to use SCHC inside their architectures.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of six months RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 18 June 2023.
https://www.rfc-editor.org/info/rfc9391.
Copyright Notice
Copyright (c) 2022 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info)
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Revised BSD License text as described in Section 4.e of the
Trust Legal Provisions and are provided without warranty as described
in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Conventions and Definitions . . . . . . . . . . . . . . . . . 3
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. NB-IoT Architecture . . . . . . . . . . . . . . . . . . . . . 5
5. Data Transmission in the 3GPP Architecture . . . . . . . . . 6
5.1. Normative Part. . . . . . . . . . . . . . . . . . . . . . 7 Scenarios
5.1.1. SCHC over Non-IP Data Delivery (NIDD) . . . . . . . . 7
5.2. Informational Part. . . . . . . . . . . . . . . . . . . . 10 Scenarios
5.2.1. Use of SCHC over the Radio link . . . . . . . . . . . 11 Link
5.2.2. Use of SCHC over the Non-Access Stratum (NAS) . . . . 12
5.2.3. Parameters for Static Context Header Compression and
Fragmentation (SCHC) for the Radio link Link and DONAS
use-cases. . . . . . . . . . . . . . . . . . . . . . 13 DoNAS Use
Cases
6. Padding . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7. IANA considerations . . . . . . . . . . . . . . . . . . . . . 15 Considerations
8. Security considerations . . . . . . . . . . . . . . . . . . . 15 Considerations
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 15
9.1. Normative References . . . . . . . . . . . . . . . . . . 16
9.2. Informative References . . . . . . . . . . . . . . . . . 16
Appendix A. NB-IoT User Plane protocol architecture . . . . . . 17 Protocol Architecture
A.1. Packet Data Convergence Protocol (PDCP) TS36323 . . . . . 18
A.2. Radio Link Protocol (RLC) TS36322 . . . . . . . . . . . . 18
A.3. Medium Access Control (MAC) TR36321 . . . . . . . . . . . 19
Appendix B. NB-IoT Data over NAS (DoNAS) . . . . . . . . . . . . 20
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 23
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 23
1. Introduction
This document defines the scenarios where the Static Context Header
Compression and fragmentation (SCHC) [RFC8724] and [RFC8824] are suitable
for 3rd Generation Partnership Project (3GPP) and Narrowband Internet
of Things (NB-IoT) protocol stacks.
In the 3GPP and the NB-IoT networks, header compression efficiently
brings Internet connectivity to the Device-User Equipment Device UE (Dev-UE), the radio
(RGW-eNB) and network (NGW-MME) gateways, and the Application Server.
This document describes the SCHC parameters supporting static context header compression and fragmentation SCHC over the
NB-IoT architecture.
This document assumes functionality for NB-IoT of 3GPP release 15
[_3GPPR15].
[R15-3GPP]. Otherwise, the text explicitly mentions other versions'
functionality.
This document has two parts, a standard parts: normative end-to-end scenario scenarios
describing how any application must use SCHC over the 3GPP public
service. And
service and informational scenarios about how 3GPP could use SCHC in
their protocol stack network.
2. Conventions and Definitions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Terminology
This document will follow the terms defined in [RFC8724], in [RFC8376],
and the [TR23720].
*
Capillary Gateway. A capillary gateway facilitates Gateway: Facilitates seamless integration because it has wide area
wide-area connectivity through cellular and provides wide area wide-area
access as a proxy to other devices using LAN technologies (BT, Wi-Fi, Wi-
Fi, Zigbee, or others.)
* CIoT EPS. others).
Cellular IoT Evolved Packet System. It is a System (CIoT EPS): A functionality to
improve the support of small data transfers.
* Dev-UE.
Device - User Equipment.
* DoNAS. UE (Dev-UE): As defined in [RFC8376], Section 3.
Data over Non-Access Stratum.
* EPC. Stratum (DoNAS): Sending user data within
signaling messages over the NAS functional layer.
Evolved Packet Connectivity. Connectivity (EPC): Core network of 3GPP LTE systems.
* EUTRAN.
Evolved Universal Terrestrial Radio Access Network. Network (EUTRAN): Radio
access network of LTE-based systems.
* HARQ.
Hybrid Automatic Repeat Request.
* HSS. reQuest (HARQ): A combination of high-rate
Forward Error Correction (FEC) and Automatic Repeat reQuest (ARQ)
error control.
Home Subscriber Server. It is a Server (HSS): A database that contains users'
subscription data, including data needed for mobility management.
*
IP address. address: IPv6 or IPv4 address used.
* IWK-SCEF.
InterWorking Service Capabilities Exposure Function.
It is used Function (IWK-SCEF): Used
in roaming scenarios, it is located in the Visited PLMN PLMN, and serves
for interconnection with the SCEF Service Capabilities Exposure
Function (SCEF) of the Home PLMN.
* L2. Layer-2
Layer 2 (L2): L2 in the 3GPP architectures it includes MAC, RLC RLC, and
PDCP layers layers; see Appendix A.
* LCID.
Logical Channel ID. Is the ID (LCID): The logical channel instance of the
corresponding MAC SDU.
* MAC.
Medium Access Control protocol, part (MAC) protocol: Part of L2.
* NAS.
Non-Access Stratum.
* NB-IoT. Stratum (NAS): Functional layer for signaling messages
that establishes communication sessions and maintains the
communication while the user moves.
Narrowband IoT. IoT (NB-IoT): A 3GPP LPWAN Low-Power WAN (LPWAN) technology
based on the LTE architecture but with additional optimization for
IoT and using a Narrowband spectrum frequency.
* NGW-CSGN.
Network Gateway - CIoT Serving Gateway Node.
* NGW-CSGW. Node (NGW-CSGN): As defined
in [RFC8376], Section 3.
Network Gateway - Cellular Serving Gateway. It routes Gateway (NGW-CSGW): Routes and
forwards the user data packets through the access network.
* NGW-MME.
Network Gateway - Mobility Management Entity. Entity (NGW-MME): An entity in
charge of handling mobility of the Dev-UE.
* NGW-PGW.
Network Gateway - Packet Data Network Gateway. Gateway (NGW-PGW): An
interface between the internal with the and external network.
* NGW-SCEF.
Network Gateway - Service Capability Exposure Function.
EPC Function (NGW-SCEF): E
PC node for exposure of 3GPP network service capabilities to 3rd third
party applications.
* NIDD.
Non-IP Data Delivery.
* PDCP. Delivery (NIDD): End-to-end communication between the UE
and the Application Server.
Packet Data Convergence Protocol part (PDCP): Part of L2.
* PLMN.
Public Land Land-based Mobile Network. Combination Network (PLMN): A combination of wireless
communication services offered by a specific operator.
* PDU.
Protocol Data Unit. Unit (PDU): A data packet including headers that are
transmitted between entities through a protocol.
* RLC.
Radio Link Protocol part (RLC): Part of L2.
* RGW-eNB.
Radio Gateway - evolved Node B. B (RGW-eNB): Base Station that controls
the UE.
* SDU.
Service Data Unit. Unit (SDU): A data packet (PDU) from higher layer higher-layer
protocols used by lower layer lower-layer protocols as a payload of their own
PDUs.
4. NB-IoT Architecture
The Narrowband Internet of Things (NB-IoT) NB-IoT architecture has a complex structure. It relies on
different NGWs Network Gateways (NGWs) from different providers. It can
send data via different paths, each with different characteristics in
terms of bandwidth, acknowledgments, and layer-2 L2 reliability and
segmentation.
Figure 1 shows this architecture, where the Network Gateway -
Cellular
Internet of Things IoT Serving Gateway Node (NGW-CSGN) optimizes co-
locating co-locating
entities in different paths. For example, a Dev-UE using the path
formed by the Network Gateway - Mobility Management Entity (NGW-MME),
the NGW-CSGW, and the Network Gateway - Packet Data Network Gateway
(NGW-PGW) may get a limited bandwidth transmission from a few bytes/s
to one thousand bytes/s only.
Another node introduced in the NB-IoT architecture is the Network
Gateway - Service Capability Exposure Function (NGW-SCEF), which
securely exposes service and network capabilities to entities
external to the network operator. The Open Mobile Alliance (OMA)
[OMA0116] and the One Machine to Machine (OneM2M) [TR-0024] define
the northbound APIs. [TS23222] defines architecture for the common
API framework for 3GPP northbound APIs and APIs. [TS33122] defines security
aspects for a common API framework for 3GPP northbound APIs. In this
case, the path is small for data transmission. The main functions of
the NGW-SCEF are Connectivity path connectivity and Device Monitoring. device monitoring.
+---+ +---------+ +------+
|Dev| \ | +-----+ | ---| HSS |
|-UE| \ | | NGW | | +------+
+---+ | | |-MME |\__
\ / +-----+ | \
+---+ \+-----+ /| | | +------+
|Dev| ----| RGW |- | | | | NGW- |
|-UE| |-eNB | | | | | SCEF |---------+
+---+ /+-----+ \| | | +------+ |
/ \ +------+| |
/ |\| NGW- || +-----+ +-----------+
+---+ / | | CSGW |--| NGW-|---|Application|
|Dev| | | || | PGW | | Server |
|-UE| | +------+| +-----+ +-----------+
+---+ | |
|NGW-CSGN |
+---------+
Figure 1: 3GPP network architecture Network Architecture
5. Data Transmission in the 3GPP Architecture
NB-IoT networks deal with end-to-end user data and in-band signaling
between the nodes and functions to configure, control, and monitor
the system functions and behaviors. The signaling uses a different
path with specific protocols, handling processes, and entities but
can transport end-to-end user data for IoT services. In contrast,
the end-to-end application only transports end-to-end data.
The recommended 3GPP MTU size is 1358 bytes. The radio network
protocols limit the packet sizes over the air, including radio
protocol overhead, to 1600 bytes, bytes; see Section 5.2.3. However, the
recommended 3GPP MTU is smaller to avoid fragmentation in the network
backbone due to the payload encryption size (multiple of 16) and the
additional core transport overhead handling.
3GPP standardizes NB-IoT and, in general, the cellular technologies interfaces and functions.
functions of cellular technologies. Therefore, the introduction of
SCHC entities to Dev-UE, RGW-eNB, and NGW-CSGN needs to be specified
in the NB-IoT standard.
This document identifies the use cases of SCHC over the NB-IoT
architecture.
First,
The first use case is of the radio transmission where, see (see Section 5.2.1, 5.2.1)
where the Dev-UE and the RGW-eNB can use the SCHC functionalities.
Second,
The second is where the packets transmitted over the control path can
also use SCHC when the transmission goes over the NGW-MME or NGW-SCEF. See NGW-SCEF
(see Section 5.2.2. 5.2.2).
These two use cases are also valid for any 3GPP architecture and not
only for NB-IoT. And as the 3GPP internal network is involved, they
have been put in the informational part of this section.
And third, over the third covers the SCHC over Non-IP Data Delivery (NIDD)
connection or at least up to the operator network edge, see edge (see
Section 5.1.1. 5.1.1). In this case, SCHC functionalities are available in
the application layer of the Dev-UE and the Application Servers or a
broker function at the edge of the operator network. NGW-PGW or NGW-SCEF NGW-
SCEF transmit the packets which that are non-IP Non-IP traffic, using IP tunneling
or API calls. It is also possible to benefit legacy devices with
SCHC by using the non-IP Non-IP transmission features of the operator
network.
A non-IP Non-IP transmission refers to other layer-2 an L2 transport that is different
from NB-IoT.
5.1. Normative Part.
This Scenarios
These scenarios does do not modify the 3GPP architecture or any of its
components, it
components. They only use it the architecture as a layer-2 an L2 transmission.
5.1.1. SCHC over Non-IP Data Delivery (NIDD)
This section specifies the use of SCHC over Non-IP Data Delivery
(NIDD) NIDD services of 3GPP.
The NIDD services of 3GPP enable the transmission of SCHC packets
compressed by the application layer. The packets can be delivered
between the NGW-PGW and the Application Server or between the NGW-SCEF NGW-
SCEF and the Application Server, using IP-
tunnels IP-tunnels or API calls. In
both cases, as compression occurs before transmission, the network
will not understand the packet, and the network does not have context
information of this compression. Therefore, the network will treat
the packet as Non-IP traffic and deliver it to the other side without
any other protocol stack element, directly over the layer-2. L2.
5.1.1.1. SCHC Entities Placing over NIDD
In the two scenarios using NIDD compression, SCHC entities are
located almost on top of the stack. The NB-IoT connectivity services
implement SCHC in the Dev-UE, an in the Application Server. The IP
tunneling scenario requires that the Application Server send the
compressed packet over an IP connection terminated by the 3GPP core
network. If the transmission uses the NGW-SCEF services, it is
possible to utilize an API call to transfer the SCHC packets between
the core network and the Application Server. Also, an IP tunnel
could be established by the Application Server if negotiated with the
NGW-SCEF.
+---------+ XXXXXXXXXXXXXXXXXXXXXXXX +--------+
| SCHC | XXX XXX | SCHC |
|(Non-IP) +-----XX........................XX....+--*---+(Non-IP)|
+---------+ XX +----+ XX | | +--------+
| | XX |SCEF+-------+ | | |
| | XXX 3GPP RAN & +----+ XXX +---+ UDP |
| | XXX CORE NETWORK XXX | | |
| L2 +---+XX +------------+ | +--------+
| | XX |IP TUNNELING+--+ | |
| | XXX +------------+ +---+ IP |
+---------+ XXXX XXXX | +--------+
| PHY +------+ XXXXXXXXXXXXXXXXXXXXXXX +---+ PHY |
+---------+ +--------+
Dev-UE Application
Server
Figure 2: End-to End Compression. End-to-End Compression: SCHC entities placed Entities Placed when
using Using
Non-IP Delivery (NIDD) 3GPP Services
5.1.1.2. Parameters for Static Context Header Compression and
Fragmentation (SCHC)
These scenarios MAY use the SCHC header compression capability to
improve the transmission of IPv6 packets.
* SCHC Context initialization. Initialization
The application layer handles the static context; consequently, context. Consequently,
the context distribution MUST be according to the application's
capabilities, perhaps utilizing IP data transmissions up to
context initialization. Also, the static contexts context delivery may use
the same IP tunneling or NGW-SCEF services used later for the
transport of SCHC packets
transport. packets.
* SCHC Rules. Rules
For devices acting as a capillary gateway, several rules match the
diversity of devices and protocols used by the devices associated
with the gateway. Meanwhile, simpler devices may have
predetermined protocols and fixed parameters.
* Rule ID. RuleID
This scenario can dynamically set the RuleID size before the
context
delivery. For delivery, for example, negotiate by negotiating between the
applications when choosing a profile according to the type of
traffic and application deployed. Transmission optimization may
require only one physical
layer Physical Layer transmission. SCHC overhead
SHOULD NOT exceed the available number of effective bits of the
smallest physical TB available to optimize the transmission. The
packets handled by 3GPP networks are byte-aligned. Thus, to use
the smallest TB, the maximum SCHC header size is 12 bits. On the
other hand, more complex NB-IoT devices (such as a capillary
gateway) might require additional bits to handle the variety and
multiple parameters of higher-layer protocols deployed. The
configuration may be part of the agreed operation profile and
content distribution. The RuleID field size may range from 2
bits, resulting in 4 rules rules, to an 8-bit value that would yield value, yielding up to 256
rules that can be used with the operators and seems quite a
reasonable for use by operators. A 256-rule maximum limit seems to be
quite reasonable, even for a device acting as a NAT. An
application may use a larger RuleID, but it should consider the
byte alignment of the expected Compression Residue. In the
minimum TB size case, 2 bits of RuleID leave only 6 bits available
for Compression Residue.
* SCHC MAX_PACKET_SIZE. MAX_PACKET_SIZE
In these scenarios, the maximum RECOMMENDED MTU size is 1358 bytes
since the SCHC packets (and fragments) are traversing the whole
3GPP network infrastructure (core and radio), not only the radio
as in the IP transmissions case.
* Fragmentation. Fragmentation
Packets larger than 1358 bytes need the SCHC fragmentation
function. Since the 3GPP uses reliability functions, the No-ACK
fragmentation mode MAY be enough in point-to-point connections.
Nevertheless, additional considerations are described below for
more complex cases.
* Fragmentation modes. Modes
A global service assigns a QoS to the packets e.g. packets, e.g., depending on
the billing. Packets with very low QoS may get lost before
arriving in the 3GPP radio network transmission, for example, e.g., in between
the links of a capillary gateway or due to buffer overflow
handling in a backhaul connection. The use of SCHC fragmentation
with the ACK-on-
Error ACK-on-Error mode is RECOMMENDED to secure additional
reliability on the packets transmitted with a small trade-off on
further transmissions to signal the end-to-end arrival of the
packets if no transport protocol takes care of retransmission.
Also, the ACK-on-Error mode could be desirable to keep track of
all the SCHC packets delivered. In that case, the fragmentation
function could be activated for all packets transmitted by the
applications. SCHC ACK-on-Error fragmentation MAY be activated in
transmitting non-
IP Non-IP packets on the NGW-MME. A non-IP Non-IP packet will
use SCHC reserved RuleID for non-compressing packets as [RFC8724]
allows it.
* Fragmentation Parameters. Parameters
SCHC profile will have specific Rules for the fragmentation modes.
The rule will identify, identify which fragmentation mode is in use, and
section
Section 5.2.3 defines the RuleID size.
SCHC parametrization considers that NBIoT NB-IoT aligns the bit and uses
padding and the size of the Transfer Block. SCHC will try to reduce
padding to optimize the compression of the information. The Header header
size needs to be a multiple of 4, and the 4. The Tiles MAY keep a fixed value
of 4 or 8 bits to avoid padding padding, except for when the transfer block
equals 16 bits where as the Tiles may be 2 bits. The transfer block size
has a wide range of values. Two configurations are RECOMMENDED for
the fragmentation parameters.
* For Transfer Blocks smaller than or equal to 304 bits using an
8-bit Header_size configuration, with the size of the header
fields as follows:
- RuleID from 1 - 3 bits, bits
- DTag 1 bit, bit
- FCN 3 bits, bits
- W 1 bits. bits
* For Transfer Blocks bigger than 304 bits using a 16-bit
Header_size configuration, with the size of the header fields as
follows:
- RulesID from 8 - 10 bits, bits
- DTag 1 or 2 bits, bits
- FCN 3 bits, bits
- W 2 or 3 bits. bits
* WINDOW_SIZE of 2^N-1 (2^N)-1 is RECOMMENDED.
* RCS Reassembly Check Sequence (RCS) will follow the default size
defined in section Section 8.2.3 of the [RFC8724], with a length equal to the
L2 Word.
* MAX_ACK_REQ is RECOMMENDED to be 2, but applications MAY change
this value based on transmission conditions.
The IoT devices communicate with small data transfer transfers and use the
Power Save Mode and the Idle Mode DRX, Discontinuous Reception (DRX),
which govern how often the device wakes up, stays up, and is
reachable. The use of the different modes allows the battery to last
ten years. Table 10.5.163a in [TS24008] specifies a range for defines the radio timers
as N to 3N in increments of one where the timer
values with units incrementing by N. The units of N can be 1 hour or
10 hours. The range used for IoT is of N to 3N, where N increments
by one. The Inactivity Timer and the Retransmission Timer can be set
based on these limits.
5.2. Informational Part. Scenarios
These scenarios shows show how 3GPP could use SCHC for their transmissions.
5.2.1. Use of SCHC over the Radio link Link
Deploying SCHC over the radio link Radio Link only would require placing it as
part of the protocol stack for data transfer between the Dev-UE and
the RGW-eNB. This stack is the functional layer responsible for
transporting data over the wireless connection and managing radio
resources. There is support for features such as reliability,
segmentation, and concatenation. The transmissions use link
adaptation, meaning that the system will optimize the transport
format used according to the radio conditions, the number of bits to
transmit, and the power and interference constraints. That means
that the number of bits transmitted over the air depends on the
selected Modulation and Coding Schemes (MCS). (MCSs). Transport Block (TB)
transmissions happen in the physical layer Physical Layer at network-synchronized
intervals called Transmission Time Interval (TTI). Each Transport
Block TB has a
different MCS and number of bits available to transmit. The MAC
layer [TR36321] defines the Transport Blocks'
characteristics. characteristics of the TBs. The Radio link
Link stack shown in Figure 3 comprises the Packet Data Convergence
Protocol (PDCP) [TS36323], the Radio Link Protocol (RLC) [TS36322],
the Medium Access Control protocol (MAC) [TR36321], and the Physical
Layer [TS36201]. The Appendix A gives more details about these
protocols.
+---------+ +---------+ |
|IP/non-IP+------------------------------+IP/non-IP+->+
|IP/Non-IP+------------------------------+IP/Non-IP+->+
+---------+ | +---------------+ | +---------+ |
| PDCP +-------+ PDCP | GTP|U +------+ GTP-U |->+
| (SCHC) + + (SCHC)| + + | |
+---------+ | +---------------+ | +---------+ |
| RLC +-------+ RLC |UDP/IP +------+ UDP/IP +->+
+---------+ | +---------------+ | +---------+ |
| MAC +-------+ MAC | L2 +------+ L2 +->+
+---------+ | +---------------+ | +---------+ |
| PHY +-------+ PHY | PHY +------+ PHY +->+
+---------+ +---------------+ +---------+ |
C-Uu/ S1-U SGi
Dev-UE RGW-eNB NGW-CSGN
Radio Link
Figure 3: SCHC over the Radio link Link
5.2.1.1. Placing SCHC Entities Placing over the Radio Link
The 3GPP architecture supports Robust Header Compression (ROHC)
[RFC5795] in the PDCP layer. Therefore, the architecture can deploy
SCHC header compression entities similarly without the need for
significant changes in the 3GPP specifications.
The RLC layer has three functional modes modes: Transparent Mode (TM),
Unacknowledged Mode (UM), and Acknowledged Mode (AM). The mode of
operation controls the functionalities of the RLC layer. TM only
applies to signaling packets, while AM or UM carry signaling and data
packets.
The RLC layer takes care of fragmentation unless except for the Transparent
Mode. TM. In AM
or UM modes, UM, the SCHC fragmentation is unnecessary and SHOULD NOT be used.
While sending IP packets, the Radio link Link does not commonly use the
RLC Transparent Mode. TM. However, if other protocol overhead optimizations are
targeted for NB-IoT traffic, SCHC fragmentation may be used for TM
transmission mode in the future.
5.2.2. Use of SCHC over the Non-Access Stratum (NAS)
This section consists of IETF suggestions to the 3GPP. The NGW-MME
conveys mainly signaling between the Dev-UE and the cellular network
[TR24301]. The network transports this traffic on top of the radio
link. Radio
Link.
This kind of flow supports data transmissions to reduce the overhead
when transmitting infrequent small quantities of data. This
transmission is known as Data over Non-Access Stratum (DoNAS) or
Control Plane Cellular Internet of Things (CIoT) evolved packet
system (EPS) CIoT EPS optimizations. In DoNAS, the Dev-UE uses the pre-
established security and
pre-established security, can piggyback small uplink data into the
initial uplink message message, and uses an additional message to receive a
downlink small data response.
The NGW-MME performs the data encryption from the network side in a
DoNAS PDU. Depending on the data type signaled indication (IP or
non-IP
Non-IP data), the network allocates an IP address or establishes a
direct forwarding path. DoNAS is regulated under rate control upon
previous agreement, meaning that a maximum number of bits per unit of
time is agreed upon per device subscription beforehand and configured
in the device.
The system will use DoNAS when a terminal in a power-saving state
requires a short transmission and receives an acknowledgment or short
feedback from the network. Depending on the size of the buffered
data to
transmit, be transmitted, the Dev-UE might deploy the connected mode transmissions
instead, limiting
transmission instead. The connected mode would limit and controlling control the
DoNAS transmissions to predefined thresholds thresholds, and it would be a good
resource optimization balance for the terminal and the network. The
support for mobility of DoNAS is present but produces additional
overhead. The Appendix B gives additional details of DoNAS.
5.2.2.1. Placing SCHC Entities Placing over DoNAS
SCHC resides in this scenario's Non-Access Stratum (NAS) protocol
layer. The same principles as for the section Section 5.2.1 apply here as well.
Because the NAS protocol already uses ROHC [RFC5795], it can also
adapt SCHC for header compression. The main difference compared to
the radio link, section Section 5.2.1, Radio Link (Section 5.2.1) is the physical placing of the SCHC
entities. On the network side, the NGW-MME resides in the core
network and is the terminating node for NAS instead of the RGW-eNB.
+--------+ +--------+--------+ + +--------+
| IP/ +--+-----------------+--+ IP/ | IP/ +-----+ IP/ |
| Non-IP | | | | Non-IP | Non-IP | | | Non-IP |
+--------+ | | +-----------------+ | +--------+
| NAS +-----------------------+ NAS |GTP-C/U +-----+GTP-C/U |
|(SCHC) | | | | (SCHC) | | | | |
+--------+ | +-----------+ | +-----------------+ | +--------+
| RRC +-----+RRC |S1|AP+-----+ S1|AP | | | | |
+--------+ | +-----------+ | +--------+ UDP +-----+ UDP |
| PDCP* +-----+PDCP*|SCTP +-----+ SCTP | | | | |
+--------+ | +-----------+ | +-----------------+ | +--------+
| RLC +-----+ RLC | IP +-----+ IP | IP +-----+ IP |
+--------+ | +-----------+ | +-----------------+ | +--------+
| MAC +-----+ MAC | L2 +-----+ L2 | L2 +-----+ L2 |
+--------+ | +-----------+ | +-----------------+ | +--------+
| PHY +--+--+ PHY | PHY +--+--+ PHY | PHY +-----+ PHY |
+--------+ +-----+-----+ +--------+--------+ | +--------+
C-Uu/ S1 SGi
Dev-UE RGW-eNB NGW-MME NGW-PGW
*PDCP is bypassed until AS security is activated TGPP36300.
Figure 4: SCHC entities placement Entities Placement in the 3GPP CIOT radio protocol
architecture Radio Protocol
Architecture for DoNAS transmissions Transmissions
5.2.3. Parameters for Static Context Header Compression and
Fragmentation (SCHC) for the Radio link Link and DONAS use-cases. DoNAS Use Cases
If 3GPP incorporates SCHC, it is recommended that these scenarios use
the SCHC header compression [RFC8724] capability to optimize the data
transmission.
* SCHC Context initialization. Initialization
The RRC (Radio Radio Resource Control) Control (RRC) protocol is the main tool used to
configure the parameters of the Radio link. Link. It will configure
SCHC and the static context distribution as it has been made for
ROHC [RFC5795] operation [RFC5795] [TS36323].
* SCHC Rules. Rules
The network operator in these scenarios defines the number of rules. rules in these
scenarios. For this, the network operator must know the IP
traffic the device will carry. The operator might supply rules
compatible with the device's use case. For devices acting as a
capillary gateway, several rules match the diversity of devices
and protocols used by the devices associated with the gateway.
Meanwhile, simpler devices may have predetermined protocols and
fixed parameters. The use of IPv6 and IPv4 may force the operator
to get develop more rules to deal with each case.
* RuleID. RuleID
There is a reasonable assumption of 9 bytes of radio protocol
overhead for these transmission scenarios in NB-IoT, where PDCP
uses 5 bytes due to header and integrity protection, protection and where RLC
and MAC use 4 bytes. The minimum physical Transport Blocks (TB) TBs that can withhold
this overhead value value, according to the 3GPP Release 15 specifications
specification [R15-3GPP], are 88, 104, 120, and 144 bits. As for
Section 5.1.1.2, these scenarios must optimize the physical layer Physical Layer
where the smallest TB is 12 bits. These 12 bits must include the
Compression Residue in addition to the RuleID. On the other hand,
more complex NB-IoT devices (such as a capillary gateway) might
require additional bits to handle the variety and multiple
parameters of higher-layer protocols deployed. In that sense, the
operator may want flexibility on the number and type of rules
independently supported by each device; consequently, these
scenarios require a configurable value. The configuration may be
part of the agreed operation profile with the content
distribution. The RuleID field size may range from 2 bits,
resulting in 4 rules rules, to an 8-bit value that would yield value, yielding up to 256 rules that
can be used
for use with the operators and seems quite a reasonable operators. A 256-rule maximum limit seems to be
quite reasonable, even for a device acting as a NAT. An
application may use a larger RuleID, but it should consider the
byte alignment of the expected Compression Residue. In the
minimum TB size case, 2 bits of RuleID leave only 6 bits available
for Compression Residue.
* SCHC MAX_PACKET_SIZE. MAX_PACKET_SIZE
The Radio Link can handle the fragmentation of SCHC packets if
needed, including reliability. Hence, the packet size is limited
by the MTU that is handled by the radio protocols, which
corresponds to 1600 bytes for the 3GPP Release 15.
* Fragmentation. Fragmentation
For the Radio link Section 5.2.1 Link (Section 5.2.1) and DoNAS' Section 5.2.2 DoNAS (Section 5.2.2)
scenarios, the SCHC fragmentation functions are disabled. The RLC
layer of NB-
IoT NB-IoT can segment packets into suitable units that fit
the selected
transport blocks TB for transmissions of the physical layer. Physical Layer. The
block selection is made according to the link adaptation input
function in the MAC layer and the quantity of data in the buffer.
The link adaptation layer may produce different results at each Time
Transmission Interval (TTI),
TTI, resulting in varying physical transport
blocks TBs that depend on the network
load, interference, number of bits transmitted, and QoS. Even if
setting a value that allows the construction of data units
following the SCHC tiles principle, the protocol overhead may be
greater or equal to allowing the Radio link Link protocols to take care
of the fragmentation intrinsically.
* Fragmentation in RLC Transparent Mode. TM
The RLC Transparent Mode TM mostly applies to control signaling transmissions.
When RLC operates in Transparent Mode, TM, the MAC layer mechanisms ensure
reliability and generate overhead. This additional reliability
implies sending repetitions or automatic retransmissions.
The ACK-Always fragmentation mode of SCHC may reduce this overhead
in future operations when data transmissions may use this mode. ACK-
Always
The ACK-Always mode may transmit compressed data with fewer
possible transmissions by using fixed or limited transport blocks TBs compatible
with the tiling SCHC fragmentation handling. For SCHC
fragmentation
parameters parameters, see Section 5.1.1.2.
6. Padding
NB-IoT and 3GPP wireless access, in general, assumes a byte-aligned
payload. Therefore, the layer 2 word L2 Word for NB-IoT MUST be considered 8
bits, and the padding treatment should use this value accordingly.
7. IANA considerations Considerations
This document has no IANA actions.
8. Security considerations Considerations
This document does not add any security considerations and follows
the
[RFC8724] and the 3GPP access security document specified in
[TS33122].
9. References
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8724] Minaburo, A., Toutain, L., Gomez, C., Barthel, D., and JC.
Zuniga, "SCHC: Generic Framework for Static Context Header
Compression and Fragmentation", RFC 8724,
DOI 10.17487/RFC8724, April 2020,
<https://www.rfc-editor.org/info/rfc8724>.
[RFC8824] Minaburo, A., Toutain, L., and R. Andreasen, "Static
Context Header Compression (SCHC) for the Constrained
Application Protocol (CoAP)", RFC 8824,
DOI 10.17487/RFC8824, June 2021,
<https://www.rfc-editor.org/info/rfc8824>.
9.2. Informative References
[OMA0116] OMA, Open Mobile Alliance, "Common definitions for RESTful
Network APIs", Version 1.0, January 2018,
<https://www.openmobilealliance.org/release/
REST_NetAPI_Common/V1_0-20180116-A/OMA-TS-
REST_NetAPI_Common-V1_0-20180116-A.pdf>.
[R15-3GPP] 3GPP, "Release 15", April 2019, <https://www.3gpp.org/
specifications-technologies/releases/release-15>.
[RFC5795] Sandlund, K., Pelletier, G., and L-E. Jonsson, "The RObust
Header Compression (ROHC) Framework", RFC 5795,
DOI 10.17487/RFC5795, March 2010,
<https://www.rfc-editor.org/info/rfc5795>.
[RFC8376] Farrell, S., Ed., "Low-Power Wide Area Network (LPWAN)
Overview", RFC 8376, DOI 10.17487/RFC8376, May 2018,
<https://www.rfc-editor.org/info/rfc8376>.
[TR-0024] OneM2M, "3GPP_Interworking", TR-0024-V4.3.0, March 2020,
<https://ftp.onem2m.org/work%20programme/WI-0037/TR-0024-
3GPP_Interworking-V4_3_0.DOCX>.
[TR23720] 3GPP, "Study on architecture enhancements for Cellular
Internet of Things", 2015, 3GPP TR 23.720 V13.0.0, March 2016,
<https://www.3gpp.org/ftp/Specs/
archive/23_series/23.720/23720-d00.zip>.
[TR24301] 3GPP, "Evolved Universal Terrestrial Radio Access
(E-UTRA); Medium Access Control (MAC) "Non-Access-Stratum (NAS) protocol
specification", for Evolved
Packet System (EPS); Stage 3", 3GPP TS 24.301 V15.8.0,
December 2019, <https://www.3gpp.org/ftp//Specs/
archive/24_series/24.301/24301-f80.zip>.
[TR36321] 3GPP, "Evolved Universal Terrestrial Radio Access
(E-UTRA); Medium Access Control (MAC) protocol
specification", 3GPP TS 36.321 V13.2.0, June 2016,
<https://www.3gpp.org/ftp/Specs/
archive/36_series/36.321/36321-d20.zip>.
[TS23222] 3GPP, "Common "Functional architecture and information flows to
support Common API Framework for 3GPP Northbound APIs", APIs;
Stage 2", 3GPP TS 23.222 V15.6.0, September 2022,
<https://www.3gpp.org/ftp/Specs/
archive/23_series/23.222/23222-f60.zip>.
[TS24008] 3GPP, "Mobile radio interface layer Layer 3 specification.", specification; Core
network protocols; Stage 3", 3GPP TS 24.008 V15.5.0,
December 2018, <https://www.3gpp.org/ftp//Specs/
archive/24_series/24.008/24008-f50.zip>.
[TS33122] 3GPP, "Security aspects of Common API Framework (CAPIF)
for 3GPP northbound APIs", 2018, 3GPP TS 33.122 V15.3.0, March
2019, <https://www.3gpp.org/ftp//Specs/
archive/33_series/33.122/33122-f30.zip>.
[TS36201] 3GPP, "Evolved Universal Terrestrial Radio Access
(E-UTRA); LTE physical layer; General description", 3GPP
TS 36.201 V15.1.0, June 2018,
<https://www.3gpp.org/ftp/Specs/
archive/36_series/36.201/36201-f10.zip>.
[TS36322] 3GPP, "Evolved Universal Terrestrial Radio Access
(E-UTRA); Radio Link Control (RLC) protocol
specification", 3GPP TS 36.322 V15.0.1, April 2018,
<https://www.3gpp.org/ftp/Specs/
archive/36_series/36.322/36322-f01.zip>.
[TS36323] 3GPP, "Evolved Universal Terrestrial Radio Access
(E-UTRA); Packet Data Convergence Protocol (PDCP)
specification", 3GPP TS 36.323 V13.2.0, June 2016,
<https://www.3gpp.org/ftp/Specs/
archive/36_series/36.323/36323-d20.zip>.
[TS36331] 3GPP, "Evolved Universal Terrestrial Radio Access
(E-UTRA); Radio Resource Control (RRC); Protocol
specification", 2018, 3GPP TS 36.331 V15.5.1, April 2019,
<https://www.3gpp.org/ftp//Specs/
archive/36_series/36.331/36331-f51.zip>.
[_3GPPR15] 3GPP, "The Mobile Broadband Standard", 2019,
<https://www.3gpp.org/release-15>.
Appendix A. NB-IoT User Plane protocol architecture Protocol Architecture
A.1. Packet Data Convergence Protocol (PDCP) [TS36323]
Each of the Radio Bearers (RB) (RBs) is associated with one PDCP entity. entity
[TS36323]. Moreover, a PDCP entity is associated with one or two RLC entities
entities, depending on the unidirectional or bi-directional bidirectional
characteristics of the RB and RLC mode used. A PDCP entity is
associated with either a control plane or a user plane with
independent configuration and functions. The maximum supported size
for NB-IoT of a PDCP SDU is 1600 octets. The primary services and
functions of the PDCP sublayer for NB-IoT for the user plane include:
* Header compression and decompression using ROHC [RFC5795]
* Transfer of user and control data to higher and lower layers
* Duplicate detection of lower layer lower-layer SDUs when re-establishing
connection (when RLC with Acknowledge Mode is in use for User
Plane only)
* Ciphering and deciphering
* Timer-based SDU discard in uplink
A.2. Radio Link Protocol (RLC) [TS36322]
RLC [TS36322] is a layer-2 an L2 protocol that operates between the UE User
Equipment (UE) and the base station (eNB). It supports the packet
delivery from higher layers to MAC, creating packets transmitted over
the air, optimizing the
Transport Block TB utilization. RLC flow of data packets is
unidirectional, and it is composed of a transmitter located in the
transmission device and a receiver located in the destination device.
Therefore, to configure bi-directional bidirectional flows, two sets of entities,
one in each direction (downlink and uplink), must be configured and
effectively peered to each other. The peering allows the
transmission of control packets (ex., (e.g., status reports) between
entities. RLC can be configured for a data transfer in one of the
following modes:
* Transparent Mode (TM). (TM)
RLC does not segment or concatenate SDUs from higher layers in
this mode and does not include any header to with the payload. RLC
receives SDUs from upper layers when acting as a transmitter and
transmits directly to its flow RLC receiver via lower layers.
Similarly, upon reception, a TM RLC receiver would only deliver
without processing not process the
packets and only deliver them to higher layers upon reception. layers.
* Unacknowledged Mode (UM). (UM)
This mode provides support for segmentation and concatenation of
payload. The RLC packet's size depends on the indication given at
a particular transmission opportunity by the lower layer (MAC) and
is octet-aligned. The packet delivery to the receiver does not
include reliability support, and the loss of a segment from a
packet means a complete packet loss. Also, in the case of lower layer lower-layer
retransmissions, there is no support for re-segmentation in case of change of
the radio conditions triggering change and trigger the selection of a smaller transport
block.
TB. Additionally, it provides PDU duplication detection and
discards, reordering of out-of-sequence, out-of-sequence reordering, and loss detection.
* Acknowledged Mode (AM). (AM)
In addition to the same functions supported by UM, this mode also
adds a moving windows-based reliability service on top of the lower layer
lower-layer services. It also supports re-segmentation, and it
requires bidirectional communication to exchange acknowledgment reports
reports, called RLC Status
Report Reports, and to trigger
retransmissions. This model also supports
protocol error protocol-error
detection. The mode used depends on the operator configuration
for the type of data to be transmitted. For example, data
transmissions supporting mobility or requiring high reliability
would be most likely configured using AM. Meanwhile, streaming
and real-time data would be mapped to a UM configuration.
A.3. Medium Access Control (MAC) [TR36321]
MAC [TR36321] provides a mapping between the higher layers
abstraction called Logical Channels (which are comprised by the
previously described protocols to protocols) and the Physical layer Layer channels
(transport channels). Additionally, MAC may multiplex packets from
different Logical Channels and prioritize
what which ones to fit into one Transport Block
TB if there is data and space available to maximize data transmission
efficiency. MAC also provides error correction and reliability
support through Hybrid Automatic Repeat reQuest (HARQ), transport
format selection, and scheduling information reporting reported from the
terminal to the network. MAC also adds the necessary padding and
piggyback control elements elements, when possible and possible, as well as the higher
layers data.
<Max. 1600 bytes>
+---+ +---+ +------+
Application |AP1| |AP1| | AP2 |
(IP/non-IP)
(IP/Non-IP) |PDU| |PDU| | PDU |
+---+ +---+ +------+
| | | | | |
PDCP +--------+ +-------- +-----------+
|PDCP|AP1| |PDCP|AP1| |PDCP| AP2 |
|Head|PDU| |Head|PDU| |Head| PDU |
+--------+ +--------+ +--------+--\
| | | | | | | | |\ `--------\
+---------------------------+ | |(1)| `-------\(2)\
RLC |RLC |PDCP|AP1|RLC |PDCP|AP1| +-------------+ +----|---+
|Head|Head|PDU|Head|Head|PDU| |RLC |PDCP|AP2| |RLC |AP2|
+-------------|-------------+ |Head|Head|PDU| |Head|PDU|
| | | | | +---------|---+ +--------+
| | | LCID1 | | / / / / /
/ / / _/ _// _/ _/ / LCID2 /
| | | | | / _/ _/ / ___/
| | | | || | | / /
+------------------------------------------+ +-----------+---+
MAC |MAC|RLC|PDCP|AP1|RLC|PDCP|AP1|RLC|PDCP|AP2| |MAC|RLC|AP2|Pad|
|Hea|Hea|Hea |PDU|Hea|Hea |PDU|Hea|Hea |PDU| |Hea|Hea|PDU|din|
|der|der|der | |der|der | |der|der | | |der|der| |g |
+------------------------------------------+ +-----------+---+
TB1 TB2
(1) Segment One
(2) Segment Two
Figure 5: Example of User Plane packet encapsulation Packet Encapsulation for two
transport blocks Two
Transport Blocks
Appendix B. NB-IoT Data over NAS (DoNAS)
The Access Stratum (AS) protocol stack used by DoNAS is specific
because the radio network still needs to establish the security
associations and reduce the protocol overhead, overhead so that the PDCP (Packet
Data Convergence Protocol) is
bypassed until the AS security is activated. RLC (Radio Link Control protocol) uses, by By default, RLC uses
the
AM mode, but AM. However, depending on the network's features and the
terminal, it RLC may change to other modes by the network operator. For
example, the
transparent mode TM does not add any header or nor process the payload to
reduce the overhead, but the MTU would be limited by the transport
block TB used to
transmit the data, which is a couple of thousand bits maximum. If UM
(only terminals compatible with 3GPP Release 15 compatible terminals) [R15-3GPP]) is used,
the RLC mechanisms of reliability are disabled, and only the
reliability provided by the MAC layer by HARQ is available. In this
case, the protocol overhead might be smaller than the AM case because
of the lack of status reporting reporting, but with the overhead would have the same
support for segmentation up to 1600 bytes. NAS packets are
encapsulated within an RRC (Radio
Resource Control) [TS36331] message.
Depending on the data type indication signaled (IP or non-IP Non-IP data),
the network allocates an IP address or establishes a direct
forwarding path. DoNAS is regulated under rate control upon previous
agreement, meaning that a maximum number of bits per unit of time is
agreed upon per device subscription beforehand and configured in the
device. The use of DoNAS is typically expected when a terminal in a
power-saving state requires a short transmission and is receiving an
acknowledgment or short feedback from the network. Depending on the
size of buffered data to transmit, be transmitted, the UE might be instructed
to deploy the connected mode transmissions instead, limiting and
controlling the DoNAS transmissions to predefined thresholds and a
good resource optimization balance for the terminal and the network.
The support for mobility of DoNAS is present but produces additional
overhead.
+--------+ +--------+ +--------+
| | | | | | +-----------------+
| UE | | C-BS | | C-SGN | |Roaming Scenarios|
+----|---+ +--------+ +--------+ | +--------+ |
| | | | | | |
+----------------|------------|+ | | P-GW | |
| Attach | | +--------+ |
+------------------------------+ | | |
| | | | | |
+------|------------|--------+ | | | |
|RRC Connection Establishment| connection establishment| | | | |
|with NAS PDU transmission | | | | |
|& Ack Rsp | | | | |
+----------------------------+ | | | |
| | | | | |
| |Initial UE | | | |
| |message | | | |
| |----------->| | | |
| | | | | |
| | +---------------------+| | |
| | |Checks Integrity || | |
| | |protection, decrypts || | |
| | |data || | |
| | +---------------------+| | |
| | | Small data packet |
| | |------------------------------->
| | | Small data packet |
| | |<-------------------------------
| | +----------|---------+ | | |
| | Integrity protection,| | | |
| | encrypts data | | | |
| | +--------------------+ | | |
| | | | | |
| |Downlink NAS| | | |
| |message | | | |
| |<-----------| | | |
+-----------------------+ | | | |
|Small Data Delivery, data delivery, | | | | |
|RRC connection release | | | | |
+-----------------------+ | | | |
| |
| |
+-----------------+
Figure 6: DoNAS transmission sequence Transmission Sequence from an Uplink initiated access Initiated Access
+---+ +---+ +---+ +----+
Application |AP1| |AP1| |AP2| |AP2 |
(IP/non-IP)
(IP/Non-IP) |PDU| |PDU| |PDU| ............... |PDU |
+---+ +---+ +---+ +----+
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| |/ / | \ | |
NAS /RRC +--------+---|---+----+ +---------+
|NAS/|AP1|AP1|AP2|NAS/| |NAS/|AP2 |
|RRC |PDU|PDU|PDU|RRC | |RRC |PDU |
+--------+-|-+---+----+ +---------|
| | | | |
| |\ | | |
|<--Max. 1600 bytes-->|__ |_ |
| | \__ \___ \_ \
| | \ \ \__ \
| | \ | | \_
+---------------|+-----|----------+ \ \
RLC |RLC | NAS/RRC ||RLC | NAS/RRC | +----|-------+
|Head| PDU(1/2)||Head | PDU (2/2)| |RLC |NAS/RRC|
+---------------++----------------+ |Head|PDU |
| | | \ | +------------+
| | LCID1 | \ | | /
| | | \ \ | |
| | | \ \ | |
| | | \ \ \ |
+----+----+----------++-----|----+---------++----+---------|---+
MAC |MAC |RLC | RLC ||MAC |RLC | RLC ||MAC | RLC |Pad|
|Head|Head| PAYLOAD ||Head |Head| PAYLOAD ||Head| PDU | |
+----+----+----------++-----+----+---------++----+---------+---+
TB1 TB2 TB3
Figure 7: Example of User Plane packet encapsulation Packet Encapsulation for Data
over NAS
Acknowledgements
The authors would like to thank (in alphabetic order): Carles Gomez,
Antti Ratilainen, Tuomas Tirronen, Pascal Thubert, Eric Tuomas Tirronen, and Éric Vyncke.
Authors' Addresses
Edgar Ramos
Ericsson
Hirsalantie 11
FI- 02420
FI-02420 Jorvas, Kirkkonummi
Finland
Email: edgar.ramos@ericsson.com
Ana Minaburo
Acklio
1137A Avenue des Champs Blancs
35510 Cesson-Sevigne Cedex
France
Email: ana@ackl.io