Internet Engineering Task Force (IETF) F. Brockners, Ed.
Request for Comments: 9452 Cisco
Category: Standards Track S. Bhandari, Ed.
ISSN: 2070-1721 Thoughtspot
August 2023
Network Service Header (NSH) Encapsulation for In Situ OAM (IOAM) Data
Abstract
In situ Operations, Administration, and Maintenance (IOAM) is used
for recording and collecting operational and telemetry information
while the packet traverses a path between two points in the network.
This document outlines how IOAM data fields IOAM-Data-Fields are encapsulated with the
Network Service Header (NSH).
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
https://www.rfc-editor.org/info/rfc9452.
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Revised BSD License text as described in Section 4.e of the
Trust Legal Provisions and are provided without warranty as described
in the Revised BSD License.
Table of Contents
1. Introduction
2. Conventions
3. IOAM Encapsulation with NSH
4. IANA Considerations
5. Security Considerations
6. References
6.1. Normative References
6.2. Informative References
Appendix A. Discussion of the IOAM-Encapsulation Approach
Acknowledgments
Contributors
Authors' Addresses
1. Introduction
IOAM, as defined in [RFC9197], is used to record and collect OAM
information while the packet traverses a particular network domain.
The term "in situ" refers to the fact that the OAM data is added to
the data packets rather than what is being sent within packets
specifically dedicated to OAM. This document defines how IOAM data
fields IOAM-Data-
Fields are transported as part of the Network Service Header (NSH)
encapsulation [RFC8300] for the Service Function Chaining (SFC)
Architecture [RFC7665]. The IOAM-Data-Fields are defined in
[RFC9197].
2. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
Abbreviations used in this document:
IOAM: In situ Operations, Administration, and Maintenance
MD: NSH Metadata, see [RFC7665]
NSH: Network Service Header
OAM: Operations, Administration, and Maintenance
SFC: Service Function Chaining
TLV: Type, Length, Value
3. IOAM Encapsulation with NSH
The NSH is defined in [RFC8300]. IOAM-Data-Fields are carried as NSH
payload using a Next Protocol header that follows the NSH headers.
An IOAM header containing the IOAM-Data-Fields is added. The IOAM-
Data-Fields MUST follow the definitions corresponding to IOAM-Option- IOAM Option-
Types (e.g., see Section 4 of [RFC9197] and Section 3.2 of
[RFC9326]). In an administrative domain where IOAM is used,
insertion of the IOAM header in NSH is enabled at the NSH tunnel
endpoints, which are also configured to serve as IOAM encapsulating/decapsulating encapsulating and
decapsulating nodes
by means of configuration. for IOAM. The operator MUST ensure that SFC-aware SFC-
aware nodes along the Service Function Path support IOAM; otherwise,
packets might be dropped (see Section 3 futher below, the last paragraph of this section as
well as Section 2.2 of [RFC8300]). The IOAM transit nodes (e.g., a
Service Function Forwarder (SFF)) MUST process all the IOAM headers
that are relevant based on its configuration. See [RFC9378] for a
discussion of deployment-related aspects of IOAM-Data-Fields.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+
|Ver|O|U| TTL | Length |U|U|U|U|MD Type| NP = 0x06 | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ N
| Service Path Identifier | Service Index | S
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ H
| ... | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+
| IOAM-Type | IOAM HDR Len | Reserved | Next Protocol | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ I
! | O
! | A
~ IOAM Option and Optional Data Space ~ M
| | |
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+<-+
| |
| |
| Payload + Padding (L2/L3/...) |
| |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1
The NSH header and fields are defined in [RFC8300]. The O bit MUST
be handled following the rules in [RFC9451]. The "NSH Next Protocol"
value (referred to as "NP" in the diagram above) is 0x06.
The IOAM-related fields in NSH are defined as follows:
IOAM-Type:
8-bit field defining the IOAM-Option-Type, IOAM Option-Type, as defined in the "IOAM
Option-Type" registry specified in [RFC9197].
IOAM HDR Len:
8-bit field that contains the length of the IOAM header in
multiples of 4-octets, including the "IOAM-Type" and "IOAM HDR
Len" fields.
Reserved bits:
Reserved bits are present for future use. The reserved bits MUST
be set to 0x0 upon transmission and ignored upon receipt.
Next Protocol:
8-bit unsigned integer that determines the type of header
following IOAM. The semantics of this field are identical to the
Next Protocol field in [RFC8300].
IOAM Option and Optional Data Space:
IOAM-Data-Fields as specified by the IOAM-Type field. IOAM-Data-
Fields are defined corresponding to the IOAM-Option-Type IOAM Option-Type (e.g.,
see Section 4 of [RFC9197] and Section 3.2 of [RFC9326]) and are
always aligned by 4 octets. Thus, there is no padding field.
Multiple IOAM-Option-Types IOAM Option-Types MAY be included within the NSH
encapsulation. For example, if an NSH encapsulation contains two
IOAM-Option-Types
IOAM Option-Types before a data payload, the Next Protocol field of
the first IOAM option will contain the value 0x06, while the Next
Protocol field of the second IOAM-Option-Type IOAM Option-Type will contain the "NSH
Next Protocol" number indicating the type of the data payload. The
applicability of the IOAM Active and Loopback flags [RFC9322] is
outside the scope of this document and may be specified in the
future.
In case the IOAM Incremental Trace Option-Type is used, an SFC-aware
node that serves as an IOAM transit node needs to adjust the "IOAM
HDR Len" field accordingly. See Section 4.4 of [RFC9197].
Per Section 2.2 of [RFC8300], packets with unsupported Next Protocol
values SHOULD be silently dropped by default. Thus, when a packet
with IOAM is received at an NSH-based forwarding node (such as an
SFF) that does not support the IOAM header, it SHOULD drop the
packet. The mechanisms to maintain and notify of such events are
outside the scope of this document.
4. IANA Considerations
IANA has allocated the following code point for IOAM in the "NSH Next
Protocol" registry (https://www.iana.org/assignments/nsh):
+===============+=====================+===========+
| Next Protocol | Description | Reference |
+===============+=====================+===========+
| 0x06 | IOAM (Next Protocol | RFC 9452 |
| | is an IOAM header) | |
+---------------+---------------------+-----------+
Table 1
5. Security Considerations
IOAM is considered a "per domain" feature, where the operator decides
on leveraging
how to leverage and configuring configure IOAM according to the operator's needs.
The operator needs to properly secure the IOAM domain to avoid
malicious configuration and use, which could include injecting
malicious IOAM packets into a domain. For additional IOAM-related
security considerations, see Section 9 of [RFC9197]. For additional
OAM- and NSH-related security considerations, see Section 5 of
[RFC9451].
6. References
6.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8300] Quinn, P., Ed., Elzur, U., Ed., and C. Pignataro, Ed.,
"Network Service Header (NSH)", RFC 8300,
DOI 10.17487/RFC8300, January 2018,
<https://www.rfc-editor.org/info/rfc8300>.
[RFC9197] Brockners, F., Ed., Bhandari, S., Ed., and T. Mizrahi,
Ed., "Data Fields for In Situ Operations, Administration,
and Maintenance (IOAM)", RFC 9197, DOI 10.17487/RFC9197,
May 2022, <https://www.rfc-editor.org/info/rfc9197>.
[RFC9451] Boucadair, M., "Operations, Administration, and
Maintenance (OAM) Packet and Behavior in the Network
Service Header (NSH)", RFC 9451, DOI 10.17487/RFC9451,
August 2023, <https://www.rfc-editor.org/info/rfc9451>.
6.2. Informative References
[RFC7665] Halpern, J., Ed. and C. Pignataro, Ed., "Service Function
Chaining (SFC) Architecture", RFC 7665,
DOI 10.17487/RFC7665, October 2015,
<https://www.rfc-editor.org/info/rfc7665>.
[RFC9322] Mizrahi, T., Brockners, F., Bhandari, S., Gafni, B., and
M. Spiegel, "In Situ Operations, Administration, and
Maintenance (IOAM) Loopback and Active Flags", RFC 9322,
DOI 10.17487/RFC9322, November 2022,
<https://www.rfc-editor.org/info/rfc9322>.
[RFC9326] Song, H., Gafni, B., Brockners, F., Bhandari, S., and T.
Mizrahi, "In Situ Operations, Administration, and
Maintenance (IOAM) Direct Exporting", RFC 9326,
DOI 10.17487/RFC9326, November 2022,
<https://www.rfc-editor.org/info/rfc9326>.
[RFC9378] Brockners, F., Ed., Bhandari, S., Ed., Bernier, D., and T.
Mizrahi, Ed., "In Situ Operations, Administration, and
Maintenance (IOAM) Deployment", RFC 9378,
DOI 10.17487/RFC9378, April 2023,
<https://www.rfc-editor.org/info/rfc9378>.
Appendix A. Discussion of the IOAM-Encapsulation Approach
This section lists several approaches considered for encapsulating
IOAM with NSH and presents the rationale for the approach chosen in
this document.
An encapsulation of IOAM-Data-Fields in NSH should be friendly to an
implementation in both hardware as well as software forwarders and
support a wide range of deployment cases, including large networks
that desire to leverage multiple IOAM-Data-Fields at the same time.
* Hardware- and-software-friendly and software-friendly implementation:
Hardware forwarders benefit from an encapsulation that minimizes
iterative lookups of fields within the packet: packet. Any operation that
looks up the value of a field within the packet, based on which
another lookup is performed, and consumes additional gates and time in
an implementation -- implementation, both of which are desired to should be kept to a minimum.
This means that flat TLV structures are preferred over nested TLV
structures. IOAM-Data-Fields are grouped into several categories,
including trace, proof-of-transit, and edge-
to-edge. edge-to-edge. Each of
these options defines a TLV structure. A hardware-friendly
encapsulation approach avoids grouping these three option
categories into yet another TLV structure and would instead carry
the options as a serial sequence.
* Total length of the IOAM-Data-Fields:
The total length of IOAM-Data-Fields can grow quite large if
multiple different IOAM-Data-Fields are used and large path-
lengths need to be considered. For example, if an operator would
consider using the IOAM Trace Option-Type and capture node-id,
app_data, egress and ingress interface-id, timestamp seconds, and
timestamp nanoseconds at every hop, then a total of 20 octets
would be added to the packet at every hop. In this case, the
particular deployment has a maximum path length of 15 hops in the
IOAM domain, and a maximum of 300 octets would be encapsulated in
the packet.
Different approaches for encapsulating IOAM-Data-Fields in NSH could
be considered:
1. Encapsulation of IOAM-Data-Fields as "NSH MD Type 2" (see
[RFC8300], Section 2.5).
Each IOAM-Option-Type IOAM Option-Type (e.g., trace, proof-of-transit, and edge-
to-edge) would be specified by a type, with the different IOAM-
Data-Fields being TLVs within this the particular option type.
NSH MD Type 2 offers support for variable length metadata. The
length field is 6 bits, resulting in a maximum of 256 (2^6 x 4)
octets.
2. Encapsulation of IOAM-Data-Fields using the "Next Protocol"
field.
Each IOAM-Option-Type IOAM Option-Type (e.g., trace, proof-of-transit, and edge-
to-edge) would be specified by its own "next protocol".
3. Encapsulation of IOAM-Data-Fields using the "Next Protocol"
field.
A single NSH protocol type code point would be allocated for
IOAM. A "sub-type" field would then specify what IOAM options
type (trace, proof-of-transit, edge-to-edge) is carried.
The third option has been chosen here. This option avoids the
additional layer of TLV-nesting that the use of NSH MD Type 2 would
result in. In addition, this option does not constrain IOAM data to
a maximum of 256 octets, thus allowing support for very large
deployments.
Acknowledgments
The authors would like to thank Éric Vyncke, Nalini Elkins, Srihari
Raghavan, Ranganathan T S, Karthik Babu Harichandra Babu, Akshaya
Nadahalli, Stefano Previdi, Hemant Singh, Erik Nordmark, LJ Wobker,
Andrew Yourtchenko, Greg Mirsky, and Mohamed Boucadair for their
comments and advice.
Contributors
The following people contributed significantly to the content of this
document and should be considered coauthors:
Vengada Prasad Govindan
Cisco Systems, Inc.
Email: venggovi@cisco.com
Carlos Pignataro
Cisco Systems, Inc.
7200-11 Kit Creek Road
Research Triangle Park, NC 27709
United States of America
Email: cpignata@cisco.com
Hannes Gredler
RtBrick Inc.
Email: hannes@rtbrick.com
John Leddy
Email: john@leddy.net
Stephen Youell
JP Morgan Chase
25 Bank Street
London
E14 5JP
United Kingdom
Email: stephen.youell@jpmorgan.com
Tal Mizrahi
Huawei Network.IO Innovation Lab
Israel
Email: tal.mizrahi.phd@gmail.com
David Mozes
Email: mosesster@gmail.com
Petr Lapukhov
Facebook
1 Hacker Way
Menlo Park, CA 94025
United States of America
Email: petr@fb.com
Remy Chang
Barefoot Networks
2185 Park Boulevard
Palo Alto, CA 94306
United States of America
Authors' Addresses
Frank Brockners (editor)
Cisco Systems, Inc.
3rd Floor
Hansaallee 249
40549 Duesseldorf
Germany
Email: fbrockne@cisco.com
Shwetha Bhandari (editor)
Thoughtspot
3rd Floor, Indiqube Orion
24th Main Rd, Garden Layout, HSR Layout
Bangalore 560 102
Karnataka
India
Email: shwetha.bhandari@thoughtspot.com