Limited Additional Mechanisms for PKIX and SMIME
Internet Engineering Task Force (IETF) D. Benjamin
Internet-Draft
Request for Comments: 9618 Google LLC
Updates: 5280 (if approved) 1 February August 2024
Intended status:
Category: Standards Track
Expires: 4 August 2024
ISSN: 2070-1721
Updates to X.509 Policy Validation
draft-ietf-lamps-x509-policy-graph-05
Abstract
This document updates RFC 5280 to replace the algorithm for X.509
policy validation with an equivalent, more efficient algorithm. The
original algorithm built a structure which that scaled exponentially in the
worst case, leaving implementations vulnerable to denial-of-
service denial-of-service
attacks.
Discussion Venues
This note is to be removed before publishing as an RFC.
Discussion of this document takes place on the Limited Additional
Mechanisms for PKIX and SMIME Working Group mailing list
(spasm@ietf.org), which is archived at
https://mailarchive.ietf.org/arch/browse/spasm/.
Source for this draft and an issue tracker can be found at
https://github.com/davidben/x509-policy-graph.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of six months RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 4 August 2024.
https://www.rfc-editor.org/info/rfc9618.
Copyright Notice
Copyright (c) 2024 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info)
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Revised BSD License text as described in Section 4.e of the
Trust Legal Provisions and are provided without warranty as described
in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Summary of Changes from RFC 5280 . . . . . . . . . . . . 3
2. Conventions and Definitions . . . . . . . . . . . . . . . . . 4
3. Denial of Service Denial-of-Service Vulnerability . . . . . . . . . . . . . . . 4
3.1. Policy Trees . . . . . . . . . . . . . . . . . . . . . . 4
3.2. Exponential Growth . . . . . . . . . . . . . . . . . . . 5
3.3. Attack Vector . . . . . . . . . . . . . . . . . . . . . . 6
4. Avoiding Exponential Growth . . . . . . . . . . . . . . . . . 7
4.1. Policy Graphs . . . . . . . . . . . . . . . . . . . . . . 7
4.2. Verification Outputs . . . . . . . . . . . . . . . . . . 8
5. Updates to RFC 5280 . . . . . . . . . . . . . . . . . . . . . 9
5.1. Updates to Section 6.1 . . . . . . . . . . . . . . . . . 9
5.2. Updates to Section 6.1.2 . . . . . . . . . . . . . . . . 10
5.3. Updates to Section 6.1.3 . . . . . . . . . . . . . . . . 11
5.4. Updates to Section 6.1.4 . . . . . . . . . . . . . . . . 15
5.5. Updates to Section 6.1.5 . . . . . . . . . . . . . . . . 16
5.6. Updates to Section 6.1.6 . . . . . . . . . . . . . . . . 17
6. Other Mitigations . . . . . . . . . . . . . . . . . . . . . . 18
6.1. Verify Signatures First . . . . . . . . . . . . . . . . . 18
6.2. Limit Certificate Depth . . . . . . . . . . . . . . . . . 19
6.3. Limit Policy Tree Size . . . . . . . . . . . . . . . . . 19
6.4. Inhibit Policy Mapping . . . . . . . . . . . . . . . . . 19
6.5. Disable Policy Checking . . . . . . . . . . . . . . . . . 19
7. Implementation Status . . . . . . . . . . . . . . . . . . . . 20
8. Security Considerations . . . . . . . . . . . . . . . . . . . 20
9.
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 20
10.
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 20
10.1.
9.1. Normative References . . . . . . . . . . . . . . . . . . 20
10.2.
9.2. Informative References . . . . . . . . . . . . . . . . . 21
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 22
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 22
1. Introduction
[RFC5280] defines a suite of extensions for determining the
"policies" which policies
that apply to a certification path. A policy is described by an
object identifier (OID), (OID) and a set of optional qualifiers.
Policy validation in [RFC5280] is complex. As an overview, the
certificate policies extension (Section 4.2.1.4 of [RFC5280])
describes the policies, with optional qualifiers, under which an
individual certificate was issued. The policy mappings extension
(Section 4.2.1.5 of [RFC5280]) allows a CA certificate to map its
policy OIDs to other policy OIDs in certificates that it issues.
Subject to these mappings and other extensions, the certification
path's overall policy set is the intersection of policies asserted by
each certificate in the path, collecting the corresponding
qualifiers. path.
The procedure in Section 6.1 of [RFC5280] determines this set in the
course of certification path validation. It does so by building a
policy tree, tree containing policies asserted by each certificate and the
mappings between them. This tree can grow exponentially in the depth
of the certification path, which means an attacker, with a small
input, can cause a path validator to consume excessive memory and
computational resources. This cost asymmetry can lead to a denial-
of-service vulnerability in X.509-based applications, such as
[CVE-2023-0464] and [CVE-2023-23524].
Section 3 describes this vulnerability. Section 4.1 describes the
primary mitigation for this vulnerability, a replacement for the
policy tree structure. Section 5 provides updates to [RFC5280] which that
implement this change. Finally, Section 6 discusses alternative
mitigation strategies for X.509 applications.
1.1. Summary of Changes from RFC 5280
The algorithm for processing certificate policies and policy mappings
is replaced with one which that builds an equivalent, equivalent but much more
efficient structure. This new algorithm does not change the validity
status of any certification path, nor path or which certificate policies are
valid for it.
2. Conventions and Definitions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Denial of Service Denial-of-Service Vulnerability
This section discusses how the path validation algorithm defined in
Section 6.1.2 of [RFC5280] can lead to a denial-of-service
vulnerability in X.509-based applications.
3.1. Policy Trees
Section 6.1.2 of [RFC5280] constructs the valid_policy_tree, a tree
of certificate policies, during certification path validation. The
nodes at any given depth in the tree correspond to policies asserted
by a certificate in the certification path. A node's parent policy
is the policy in the issuer certificate which that was mapped to this
policy, and a node's children are the policies it the node was mapped to
in the subject certificate.
For example, suppose a certification path contains:
* An intermediate certificate which that asserts the following policy OIDs
OIDs: OID1, OID2, and OID5. It contains mappings from OID1 to OID3,
OID3 and from OID1 to OID4.
* An end-entity certificate which that asserts the following policy OIDs OIDs:
OID2, OID3, and OID6.
This would result in the tree shown in Figure 1. below. Note that OID5 and OID6
are not included or mapped across the whole path, so they do not
appear in the final structure.
+-----------+
Root: | anyPolicy |
+-----------+
|{anyPolicy}|
+-----------+
/ \
/ \
v v
+------------+ +------------+
Intermediate: | OID1 | | OID2 |
(OID5 discarded) +------------+ +------------+
|{OID3, OID4}| | {OID2} |
+------------+ +------------+
| |
| |
v v
+------------+ +------------+
End-entity: | OID3 | | OID2 |
(OID6 discarded) +------------+ +------------+
Figure 1: An Example X.509 Policy Tree
The complete algorithm for building this structure is described in
steps (d), (e), and (f) of in Section 6.1.3 of [RFC5280], [RFC5280]; steps (h),
(i), and (j) of in Section 6.1.4 of [RFC5280], [RFC5280]; and steps (a), (b), and
(g)
of in Section 6.1.5 of [RFC5280].
3.2. Exponential Growth
The valid_policy_tree grows exponentially in the worst case. In step
(d.1) of in Section 6.1.3 of [RFC5280], a single policy P can produce
multiple child nodes if multiple issuer policies map to P. This can
cause the tree size to increase in size multiplicatively at each
level.
In particular, consider a certificate chain where every intermediate
certificate asserts policies OID1 and OID2, OID2 and then contains the full
Cartesian product of mappings:
* OID1 maps to OID1
* OID1 maps to OID2
* OID2 maps to OID1
* OID2 maps to OID2
At each depth, the tree would double in size. For example, if there
are two intermediate certificates and one end-entity certificate, the
resulting tree would be as depicted in Figure 2. 1.
+-----------------------+
| anyPolicy |
+-----------------------+
| {anyPolicy} |
+-----------------------+
/ \
/ \
v v
+------------+ +------------+
| OID1 | | OID2 |
+------------+ +------------+
|{OID1, OID2}| |{OID1, OID2}|
+------------+ +------------+
/ \ / \
/ \ / \
v v v v
+------------+ +------------+ +------------+ +------------+
| OID1 | | OID2 | | OID1 | | OID2 |
+------------+ +------------+ +------------+ +------------+
|{OID1, OID2}| |{OID1, OID2}| |{OID1, OID2}| |{OID1, OID2}|
+------------+ +------------+ +------------+ +------------+
| | | | | | | |
v v v v v v v v
+------+ +------+ +------+ +------+ +------+ +------+ +------+ +------+
| OID1 | | OID2 | | OID1 | | OID2 | | OID1 | | OID2 | | OID1 | | OID2 |
+------+ +------+ +------+ +------+ +------+ +------+ +------+ +------+
Figure 2: 1: An Example X.509 Policy Tree with Exponential Growth
3.3. Attack Vector
An attacker can use the exponential growth to mount a denial-of-
service attack against an X.509-based application. The attacker
sends a certificate chain as described in Section 3.2 and triggers
the target application's certificate validation process. For
example, the target application may be a TLS [RFC8446] server [RFC8446] that
performs client certificate validation. The target application will
consume far more resources processing the input than the attacker
consumed to send it,
preventing it which prevents the target application from
servicing other clients.
4. Avoiding Exponential Growth
This document mitigates the denial-of-service vulnerability described
in Section 3 by replacing the policy tree with a policy graph
structure, which is described in this section. The policy graph
grows linearly instead of exponentially. This removes the asymmetric
cost in policy validation.
X.509 implementations SHOULD perform policy validation by building a
policy graph, following the procedure described in Section 5. This
replacement procedure computes the same policies as in [RFC5280],
however but
one of the outputs is in a different form. See Section 4.2 for
details. Section 6 describes alternative mitigations for
implementations that depend on the original, exponential-sized
output.
4.1. Policy Graphs
The tree structure from in [RFC5280] is an unnecessarily inefficient
representation of a certification path's policy mappings. A When
multiple issuer policies map to a single
certificate subject policy, the subject
policy may will correspond to multiple nodes, but each node is
identical, with identical children. duplicate nodes in the policy
tree. Children of the subject policy are then duplicated
recursively. This redundancy duplication is the source of the exponential
growth described in Section 3.2.
A policy graph is represents the same information with a directed
acyclic graph of policy nodes. Where
[RFC5280] adds multiple duplicate nodes, a policy graph adds It eliminates this duplication by
using a single node with multiple parents. See Section 5 for the
procedure for building this structure. Figure 3 2 shows the updated
representation of the example in Figure 2. 1.
+-----------+
| anyPolicy |
+-----------+
|{anyPolicy}|
+-----------+
/ \
/ \
v v
+------------+ +------------+
| OID1 | | OID2 |
+------------+ +------------+
|{OID1, OID2}| |{OID1, OID2}|
+------------+ +------------+
| \ / |
| \ / |
| \/ |
| /\ |
| / \ |
v v v v
+------------+ +------------+
| OID1 | | OID2 |
+------------+ +------------+
|{OID1, OID2}| |{OID1, OID2}|
+------------+ +------------+
| \ / |
| \ / |
| \/ |
| /\ |
| / \ |
v v v v
+------------+ +------------+
| OID1 | | OID2 |
+------------+ +------------+
Figure 3: 2: A More Efficient Representation of an X.509 Policy Tree
This graph's size is bounded linearly by the total number of
certificate policies (Section 4.2.1.4 of [RFC5280]) and policy
mappings (Section 4.2.1.5 of [RFC5280]). The policy tree from in
[RFC5280] is the tree of all paths from the root to a leaf in the
policy graph, so no information is lost in the graph representation.
4.2. Verification Outputs
Section 6.1.6 of [RFC5280] describes the entire valid_policy_tree
structure as an output of the verification process. However,
Section 12.2 of [X.509] instead only outputs describes the following as outputs: the
authorities-constrained policies, the user-constrained policies, and
their associated qualifiers.
As the valid_policy_tree is the exponential structure, computing it
reintroduces the denial-of-service vulnerability. X.509
implementations SHOULD NOT output the entire valid_policy_tree
structure and instead
structure; instead, they SHOULD limit output to just the set of
authorities-constrained and/or user-constrained policies, as
described in [X.509]. Section Sections 5.6 and Section 6 discuss other mitigations
for applications where this option is not available.
X.509 implementations MAY omit policy qualifiers from the output to
simplify processing. Note that Section 4.2.1.4 of [RFC5280] already
recommends that certification authorities omit policy qualifiers from
policy information terms.
5. Updates to RFC 5280
This section provides updates to [RFC5280]. This implements These updates implement
the changes described in Section 4.
5.1. Updates to Section 6.1
This update replaces a paragraph of
Section 6.1 of [RFC5280] is updated as follows:
OLD:
| A particular certification path may not, however, be appropriate
| for all applications. Therefore, an application MAY augment this
| algorithm to further limit the set of valid paths. The path
| validation process also determines the set of certificate policies
| that are valid for this path, based on the certificate policies
| extension, policy mappings extension, policy constraints
| extension, and inhibit anyPolicy extension. To achieve this, the
| path validation algorithm constructs a valid policy tree. If the
| set of certificate policies that are valid for this path is not
| empty, then the result will be a valid policy tree of depth n,
| otherwise the result will be a null valid policy tree.
NEW:
| A particular certification path may not, however, be appropriate
| for all applications. Therefore, an application MAY augment this
| algorithm to further limit the set of valid paths. The path
| validation process also determines the set of certificate policies
| that are valid for this path, based on the certificate policies
| extension, policy mappings extension, policy constraints
| extension, and inhibit anyPolicy extension. To achieve this, the
| path validation algorithm constructs a valid policy set, which may
| be empty if no certificate policies are valid for this path.
5.2. Updates to Section 6.1.2
This update
The following replaces entry (a) of in Section 6.1.2 of [RFC5280] with the
following text: [RFC5280]:
| (a) valid_policy_graph: A directed acyclic graph of certificate
| policies with their optional qualifiers; each of the leaves
| of the graph represents a valid policy at this stage in the
| certification path validation. If valid policies exist at
| this stage in the certification path validation, the depth of
| the graph is equal to the number of certificates in the chain
| that have been processed. If valid policies do not exist at
| this stage in the certification path validation, the graph is
| set to NULL. Once the graph is set to NULL, policy
| processing ceases. Implementations MAY omit qualifiers if
| not returned in the output.
|
| Each node in the valid_policy_graph includes three data
| objects: the valid policy, a set of associated policy
| qualifiers, and a set of one or more expected policy values.
|
| Nodes in the graph can be divided into depths, numbered
| starting from zero. A node at depth x can have zero or more
| children at depth x+1 and, with the exception of depth zero,
| one or more parents at depth x-1. No other edges between
| nodes may exist.
|
| If the node is at depth x, the components of the node have
| the following semantics:
|
| (1) The valid_policy is a single policy OID representing a
| valid policy for the path of length x.
|
| (2) The qualifier_set is a set of policy qualifiers
| associated with the valid policy in certificate x. It
| is only necessary to maintain this field if policy
| qualifiers are returned to the application. See
| Section 6.1.5, step (g).
|
| (3) The expected_policy_set contains one or more policy OIDs
| that would satisfy this policy in the certificate x+1.
|
| The initial value of the valid_policy_graph is a single node
| with valid_policy anyPolicy, an empty qualifier_set, and an
| expected_policy_set with the single value anyPolicy. This
| node is considered to be at depth zero.
|
| The graph additionally satisfies the following invariants:
|
| * For any depth x and policy OID P-OID, there is at most one
| node at depth x whose valid_policy is P-OID.
|
| * The expected_policy_set of a node whose valid_policy is
| anyPolicy is always {anyPolicy}.
|
| * A node at depth x whose valid_policy is anyPolicy, except
| for the one at depth zero, always has exactly one parent:
| a node at depth x-1 whose valid_policy is also anyPolicy.
|
| * Each node at depth greater than 0 has either one or more
| parent nodes whose valid_policy is not anyPolicy, anyPolicy or a
| single parent node whose valid_policy is anyPolicy. That
| is, a node cannot simultaneously be a child of both
| anyPolicy and some non-anyPolicy OID.
|
| Figure 4 3 is a graphic representation of the initial state of
| the valid_policy_graph. Additional figures will use this
| format to describe changes in the valid_policy_graph during
| path processing.
|
| +----------------+
| | anyPolicy | <---- valid_policy
| +----------------+
| | {} | <---- qualifier_set
| +----------------+
| | {anyPolicy} | <---- expected_policy_set
| +----------------+
|
| Figure 4: 3: Initial value Value of the valid_policy_graph State
| Variable
5.3. Updates to Section 6.1.3
This update
The following replaces steps (d), (e), and (f) of in Section 6.1.3 of
[RFC5280] with the following text:
[RFC5280]:
| (d) If the certificate policies extension is present in the
| certificate and the valid_policy_graph is not NULL, process
| the policy information by performing the following steps in
| order:
|
| (1) For each policy P not equal to anyPolicy in the
| certificate policies extension, let P-OID denote the OID
| for policy P and P-Q denote the qualifier set for policy
| P. Perform the following steps in order:
|
| (i) Let parent_nodes be the nodes at depth i-1 in the
| valid_policy_graph where P-OID is in the
| expected_policy_set. If parent_nodes is not
| empty, create a child node as follows: set the
| valid_policy to P-OID, set the qualifier_set to
| P-Q, set the expected_policy_set to {P-OID}, and
| set the parent nodes to parent_nodes.
|
| For example, consider a valid_policy_graph with a
| node of depth i-1 where the expected_policy_set is
| {Gold, White}, White} and a second node where the
| expected_policy_set is {Gold, Yellow}. Assume the
| certificate policies Gold and Silver appear in the
| certificate policies extension of certificate i.
| The Gold policy is matched, but the Silver policy
| is not. This rule will generate a child node of
| depth i for the Gold policy. The result is shown
| as Figure 5. 4.
|
| +-----------------+ +-----------------+
| | Red | | Blue |
| +-----------------+ +-----------------+
| | {} | | {} | depth i-1
| +-----------------+ +-----------------+
| | {Gold, White} | | {Gold, Yellow} |
| +-----------------+ +-----------------+
| \ /
| \ /
| \ /
| v v
| +-----------------+
| | Gold |
| +-----------------+
| | {} | depth i
| +-----------------+
| | {Gold} |
| +-----------------+
|
| Figure 5: 4: Processing an Exact Match
|
| (ii) If there was no match in step (i) and the
| valid_policy_graph includes a node of depth i-1
| with the valid_policy anyPolicy, generate a child
| node with the following values: set the
| valid_policy to P-OID, set the qualifier_set to
| P-Q, set the expected_policy_set to {P-OID}, and
| set the parent node to the anyPolicy node at depth
| i-1.
|
| For example, consider a valid_policy_graph with a
| node of depth i-1 where the valid_policy is
| anyPolicy. Assume the certificate policies Gold
| and Silver appear in the certificate policies
| extension of certificate i. The Gold policy does
| not have a qualifier, but the Silver policy has
| the qualifier Q-Silver. If Gold and Silver were
| not matched in (i) above, this rule will generate
| two child nodes of depth i, one for each policy.
| The result is shown as Figure 6. 5.
|
| +-----------------+
| | anyPolicy |
| +-----------------+
| | {} |
| +-----------------+ depth i-1
| | {anyPolicy} |
| +-----------------+
| / \
| / \
| / \
| v v
| +-----------------+ +-----------------+
| | Gold | | Silver |
| +-----------------+ +-----------------+
| | {} | | {Q-Silver} | depth i
| +-----------------+ +-----------------+
| | {Gold} | | {Silver} |
| +-----------------+ +-----------------+
|
| Figure 6: 5: Processing Unmatched Policies when When a
| Leaf Node Specifies anyPolicy
|
| (2) If the certificate policies extension includes the
| policy anyPolicy with the qualifier set AP-Q and either
| (a) inhibit_anyPolicy is greater than 0 or (b) i<n and
| the certificate is self-issued, then:
|
| For each policy OID P-OID (including anyPolicy) which that
| appears in the expected_policy_set of some node in the
| valid_policy_graph for depth i-1, if P-OID does not
| appear as the valid_policy of some node at depth i,
| create a single child node with the following values:
| set the valid_policy to P-OID, set the qualifier_set to
| AP-Q, set the expected_policy_set to {P-OID}, and set
| the parents to the nodes at depth i-1 where P-OID
| appears in expected_policy_set.
|
| This is equivalent to running step (1) above, above as if the
| certificate policies extension contained a policy with
| OID P-OID and qualifier set AP-Q.
|
| For example, consider a valid_policy_graph with a node
| of depth i-1 where the expected_policy_set is {Gold, Silver},
| Silver} and a second node of depth i-1 where the
| expected_policy_set is {Gold}. Assume anyPolicy appears
| in the certificate policies extension of certificate i
| with policy qualifiers AP-Q, but Gold and Silver do not
| appear. This rule will generate two child nodes of
| depth i, one for each policy. The result is shown below
| as Figure 7. 6.
|
| +-----------------+ +-----------------+
| | Red | | Blue |
| +-----------------+ +-----------------+
| | {} | | {} | depth i-1
| +-----------------+ +-----------------+
| | {Gold, Silver} | | {Gold} |
| +-----------------+ +-----------------+
| | \ |
| | \ |
| | \ |
| | \ |
| | \ |
| v v v
| +-----------------+ +-----------------+
| | Silver | | Gold |
| +-----------------+ +-----------------+
| | {AP-Q} | | {AP-Q} | depth i
| +-----------------+ +-----------------+
| | {Silver} | | {Gold} |
| +-----------------+ +-----------------+
|
| Figure 7: 6: Processing Unmatched Policies When the
| Certificate Policies Extension Specifies anyPolicy
|
| (3) If there is a node in the valid_policy_graph of depth
| i-1 or less without any child nodes, delete that node.
| Repeat this step until there are no nodes of depth i-1
| or less without children.
|
| For example, consider the valid_policy_graph shown in
| Figure 8 7 below. The two nodes at depth i-1 that are
| marked with an 'X' have no children, and they are
| deleted. Applying this rule to the resulting graph will
| cause the nodes at depth i-2 that is marked with a 'Y'
| to be deleted. In the resulting graph, there are no
| nodes of depth i-1 or less without children, and this
| step is complete.
|
| +-----------+
| | | depth i-3
| +-----------+
| / | \
| / | \
| v v v
| +-----------+ +-----------+ +-----------+
| | | | | | Y | depth i-2
| +-----------+ +-----------+ +-----------+
| | \ | |
| | \ | |
| v v v v
| +-----------+ +-----------+ +-----------+
| | X | | | | X | depth i-1
| +-----------+ +-----------+ +-----------+
| / | \
| / | \
| v v v
| +-----------+ +-----------+ +-----------+
| | | | | | | depth i
| +-----------+ +-----------+ +-----------+
|
| Figure 8: 7: Pruning the valid_policy_graph
|
| (e) If the certificate policies extension is not present, set the
| valid_policy_graph to NULL.
|
| (f) Verify that either explicit_policy is greater than 0 or the
| valid_policy_graph is not equal to NULL; NULL.
The text following step (f) in Section 6.1.3 of [RFC5280], beginning
with "If any of steps (a), (b), (c), or (f) fails", is left
unmodified.
5.4. Updates to Section 6.1.4
This update
The following replaces step (b) of in Section 6.1.4 of [RFC5280] with the
following text: [RFC5280]:
| (b) If a policy mappings extension is present, then for each
| issuerDomainPolicy ID-P in the policy mappings extension:
|
| (1) If the policy_mapping variable is greater than 0 and
| there is a node in the valid_policy_graph of depth i
| where ID-P is the valid_policy, set expected_policy_set
| to the set of subjectDomainPolicy values that are
| specified as equivalent to ID-P by the policy mappings
| extension.
|
| (2) If the policy_mapping variable is greater than 0, 0 and no
| node of depth i in the valid_policy_graph has a
| valid_policy of
ID-P, ID-P but there is a node of depth i with
| a valid_policy of anyPolicy, then generate a child node
| of the node of depth i-1 that has a valid_policy of
| anyPolicy as follows:
|
| (i) set the valid_policy to ID-P;
|
| (ii) set the qualifier_set to the qualifier set of the
| policy anyPolicy in the certificate policies
| extension of certificate i; and
|
| (iii) set the expected_policy_set to the set of
| subjectDomainPolicy values that are specified as
| equivalent to ID-P by the policy mappings
| extension.
|
| (3) If the policy_mapping variable is equal to 0:
|
| (i) delete the node, if any, of depth i in the
| valid_policy_graph where ID-P is the valid_policy.
|
| (ii) If there is a node in the valid_policy_graph of
| depth i-1 or less without any child nodes, delete
| that node. Repeat this step until there are no
| nodes of depth i-1 or less without children.
5.5. Updates to Section 6.1.5
This update
The following replaces step (g) of in Section 6.1.5 of [RFC5280] with the
following text: [RFC5280]:
| (g) Calculate the user_constrained_policy_set as follows. The
| user_constrained_policy_set is a set of policy OIDs, along
| with associated policy qualifiers.
|
| (1) If the valid_policy_graph is NULL, set
| valid_policy_node_set to the empty set.
|
| (2) If the valid_policy_graph is not NULL, set
| valid_policy_node_set to the set of policy nodes whose
| valid_policy is not anyPolicy and whose parent list is a
| single node with valid_policy of anyPolicy.
|
| (3) If the valid_policy_graph is not NULL and contains a
| node of depth n with the valid_policy anyPolicy, add it
| to valid_policy_node_set.
|
| (4) Compute authority_constrained_policy_set, a set of
| policy OIDs and associated qualifiers as follows. For
| each node in valid_policy_node_set:
|
| (i) Add the node's valid_policy to
| authority_constrained_policy_set.
|
| (ii) Collect all qualifiers in the node, its ancestors,
| and descendants and associate them with
| valid_policy. Applications that do not use policy
| qualifiers MAY skip this step to simplify
| processing.
|
| (5) Set user_constrained_policy_set to
| authority_constrained_policy_set.
|
| (6) If the user-initial-policy-set is not anyPolicy:
|
| (i) Remove any elements of user_constrained_policy_set
which
| that do not appear in user-initial-policy-set.
|
| (ii) If anyPolicy appears in
| authority_constrained_policy_set with qualifiers AP-
Q,
| AP-Q, for each OID P-OID in user-initial-policy-set
which user-initial-policy-
| set that does not appear in
| user_constrained_policy_set, add P-OID with
| qualifiers AP-Q to user_constrained_policy_set.
Additionally, this update replaces
In addition, the final paragraph in Section 6.1.5 of [RFC5280] is
updated as follows:
OLD:
| If either (1) the value of explicit_policy variable is greater
| than zero or (2) the valid_policy_tree is not NULL, then path
| processing has succeeded.
NEW:
| If either (1) the value of explicit_policy is greater than zero zero,
| or (2) the user_constrained_policy_set is not empty, then path
| processing has succeeded.
5.6. Updates to Section 6.1.6
This update
The following replaces Section 6.1.6 of [RFC5280] with the following
text: [RFC5280]:
| If path processing succeeds, the procedure terminates, returning a
| success indication together with the final value of the
| user_constrained_policy_set, the working_public_key, the
| working_public_key_algorithm, and the
| working_public_key_parameters.
|
| Note that the original procedure described in [RFC5280] included a
| valid_policy_tree structure as part of the output. This structure
| grows exponentially in the size of the input, so computing it
| risks denial-of-service vulnerabilities in X.509-based
| applications, such as [CVE-2023-0464] and [CVE-2023-23524].
| Accordingly, this output is deprecated. Computing this structure
| is NOT RECOMMENDED.
|
| An implementation which that requires valid_policy_tree for
| compatibility with legacy systems may compute it from
| valid_policy_graph by recursively duplicating every multi-parent
| node. This may be done on-demand when the calling application
| first requests this output. However, this computation may consume
| exponential time and memory, so such implementations SHOULD
| mitigate denial-of-service attacks in other ways, such as by
| limiting the depth or size of the tree.
6. Other Mitigations
X.509 implementations that are unable to switch to the policy graph
structure SHOULD mitigate the denial-of-service attack in other ways.
This section describes alternate mitigation and partial mitigation
strategies.
6.1. Verify Signatures First
X.509 validators SHOULD verify signatures in certification paths
before or in conjunction with policy verification. This limits the
attack to entities in control of CA certificates. For some
applications, this may be sufficient to mitigate the attack.
However, other applications may still be impacted. For impacted, for example:
* Any application that evaluates an untrusted PKI, such as a hosting
provider that evaluates a customer-supplied PKI
* Any application that evaluates an otherwise trusted PKI, but where PKI that
includes untrusted entities have technically-constrained with technically constrained
intermediate
certificates where certificates. If the intermediates do not constrain
policy mapping and or path length are
unconstrained. length, those entities may be able to
perform this attack.
6.2. Limit Certificate Depth
The policy tree grows exponentially in the depth of a certification
path, so limiting the depth and certificate size can mitigate the
attack.
However, this option may not be viable for all applications. Too low
of a limit may reject existing paths which that the application wishes to
accept. Too high of a limit may still admit a DoS denial-of-service
attack for the application. By modifying the example in Section 3.2
to increase the number of policies asserted in each certificate, an
attacker could still achieve O(N^(depth/2)) scaling.
6.3. Limit Policy Tree Size
The attack can be mitigated by limiting the number of nodes in the
policy tree, tree and rejecting the certification path if this limit is
reached. This limit should be set high enough to still admit
existing valid certification paths for the application, application but low enough
to no longer admit a DoS denial-of-service attack.
6.4. Inhibit Policy Mapping
If policy mapping is disabled via the initial-policy-mapping-inhibit
setting (see Section 6.1.1 of [RFC5280]), the attack is mitigated.
This also significantly simplifies the X.509 implementation, which
reduces the risk of other security bugs. However, this will break
compatibility with any existing certification paths which that rely on
policy mapping.
To facilitate this mitigation, certificate authorities SHOULD NOT
issue certificates with the policy mappings extension
(Section 4.2.1.5 of [RFC5280]). Applications maintaining policies
for accepted trust anchors are RECOMMENDED to forbid this extension
in participating certificate authorities.
6.5. Disable Policy Checking
An X.509 validator can mitigate this attack by disabling policy
validation entirely. This may be viable for applications which that do not
require policy validation. In this case, critical policy-related
extensions, notably the policy constraints extension
(Section 4.2.1.11 of [RFC5280]), MUST be treated as unrecognized
extensions as described in Section 4.2 of [RFC5280] and be rejected.
7. Implementation Status
This section is to be removed before publishing as an RFC.
This section records the status of known implementations of the
protocol defined by this specification at the time of posting of this
Internet-Draft, and is based on a proposal described in RFC 7942.
The description of implementations in this section is intended to
assist the IETF in its decision processes in progressing drafts to
RFCs. Please note that the listing of any individual implementation
here does not imply endorsement by the IETF. Furthermore, no effort
has been spent to verify the information presented here that was
supplied by IETF contributors. This is not intended as, and must not
be construed to be, a catalog of available implementations or their
features. Readers are advised to note that other implementations may
exist.
According to RFC 7942, "this will allow reviewers and working groups
to assign due consideration to documents that have the benefit of
running code, which may serve as evidence of valuable experimentation
and feedback that have made the implemented protocols more mature.
It is up to the individual working groups to use this information as
they see fit".
The following projects adopted the concept outlined in this document:
* [BoringSSL]
* [LibreSSL]
8. Security Considerations
Section 3 discusses how [RFC5280]'s the policy tree algorithm in [RFC5280] can
lead to denial-of-service vulnerabilities in X.509-based
applications, such as [CVE-2023-0464] and [CVE-2023-23524].
Section 5 replaces this algorithm to avoid this issue. As discussed
in Section 4.1, the new structure scales linearly with the input.
This means input limits in X.509 validators will more naturally bound
processing time, thus avoiding these vulnerabilities.
9.
8. IANA Considerations
This document has no IANA actions.
10.
9. References
10.1.
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/rfc/rfc2119>.
<https://www.rfc-editor.org/info/rfc2119>.
[RFC5280] Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
Housley, R., and W. Polk, "Internet X.509 Public Key
Infrastructure Certificate and Certificate Revocation List
(CRL) Profile", RFC 5280, DOI 10.17487/RFC5280, May 2008,
<https://www.rfc-editor.org/rfc/rfc5280>.
<https://www.rfc-editor.org/info/rfc5280>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.
10.2. <https://www.rfc-editor.org/info/rfc8174>.
9.2. Informative References
[BoringSSL]
"BoringSSL", January 2024,
<https://boringssl.googlesource.com/boringssl>.
[CVE-2023-0464]
CVE, "Excessive Resource Usage Verifying X.509 Policy
Constraints", CVE-2023-0464, March 2023,
<https://www.cve.org/CVERecord?id=CVE-2023-0464>.
[CVE-2023-23524]
CVE, "Processing a maliciously crafted certificate may
lead to a denial-of-service", CVE-2023-23524, February
2023, <https://www.cve.org/CVERecord?id=CVE-2023-23524>.
[LibreSSL] "LibreSSL", January 2024, <https://www.libressl.org/>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/rfc/rfc8446>.
<https://www.rfc-editor.org/info/rfc8446>.
[X.509] International Telecommunications Union, ITU-T, "Information technology - Open Systems
Interconnection - The Directory: Public-key and attribute
certificate frameworks", ITU-T Recommendation X.509,
October 2019. 2019, <https://www.itu.int/rec/T-REC-X.509>.
Acknowledgements
The author thanks Bob Beck, Adam Langley, Matt Mueller, and Ryan
Sleevi for many valuable discussions that led to discovering this
issue, understanding it, and developing the mitigation. The author
also thanks Martin Thomson and Thomson, Job Snijders Snijders, and John Scudder for their
review and feedback on this document.
Author's Address
David Benjamin
Google LLC
Email: davidben@google.com