NETCONF Working Group K. Watsen Internet-Draft Juniper Networks Intended status: Standards Track J. Schoenwaelder Expires: August 18, 2014 Jacobs University Bremen February 14, 2014 A YANG Data Model for NETCONF Server Configuration draft-kwatsen-netconf-server-01 Abstract This draft defines a NETCONF server configuration data model. This data model enables configuration of the NETCONF service itself, including which transports it supports, what ports they listen on, whether they support device-initiated connections, and associated parameters. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on August 18, 2014. Copyright Notice Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved. Watsen & Schoenwaelder Expires August 18, 2014 [Page 1] Internet-Draft YANG NETCONF Server Configuration February 2014 This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 1.2. Tree Diagrams . . . . . . . . . . . . . . . . . . . . . . 3 2. Objectives . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1. Support all NETCONF Transports . . . . . . . . . . . . . 3 2.2. Align Transport-Specific Configurations . . . . . . . . . 4 2.3. Support Transport-Independent Configuration . . . . . . . 4 2.4. Support both Inbound and Outbound Connections . . . . . . 4 2.5. For Device-Initiated Outbound Connections . . . . . . . . 4 2.5.1. Support More than One Application . . . . . . . . . . 4 2.5.2. Support Applications Having More than One Server . . 4 2.5.3. Support a Reconnection Strategy . . . . . . . . . . . 5 2.5.4. Support both Persistent and Periodic Connections . . 5 2.5.5. Keep-Alives for Persistent Connections . . . . . . . 5 2.5.6. Customizations for Periodic Connections . . . . . . . 5 3. Data Model Overview . . . . . . . . . . . . . . . . . . . . . 6 3.1. The "listen" Grouping . . . . . . . . . . . . . . . . . . 6 3.2. The "call-home" Grouping . . . . . . . . . . . . . . . . 6 3.3. The SSH Subtree . . . . . . . . . . . . . . . . . . . . . 7 3.4. The TLS Subtree . . . . . . . . . . . . . . . . . . . . . 8 4. NETCONF Server YANG Module . . . . . . . . . . . . . . . . . 9 5. Security Considerations . . . . . . . . . . . . . . . . . . . 21 6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 21 7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 21 8. References . . . . . . . . . . . . . . . . . . . . . . . . . 21 8.1. Normative References . . . . . . . . . . . . . . . . . . 22 8.2. Informative References . . . . . . . . . . . . . . . . . 22 Appendix A. Example: SSH . . . . . . . . . . . . . . . . . . . . 22 Appendix B. Example: TLS . . . . . . . . . . . . . . . . . . . . 23 Appendix C. Change Log . . . . . . . . . . . . . . . . . . . . . 25 C.1. 00 to 01 . . . . . . . . . . . . . . . . . . . . . . . . 25 Appendix D. Open Issues . . . . . . . . . . . . . . . . . . . . 25 1. Introduction Watsen & Schoenwaelder Expires August 18, 2014 [Page 2] Internet-Draft YANG NETCONF Server Configuration February 2014 This draft defines a NETCONF [RFC6241] server configuration data model. This data model enables configuration of the NETCONF service itself, including which transports it supports, what ports they listen on, whether they support device-initiated connections, and associated parameters. 1.1. Terminology The keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 1.2. Tree Diagrams A simplified graphical representation of the data model is used in this document. The meaning of the symbols in these diagrams is as follows: o Brackets "[" and "]" enclose list keys. o Abbreviations before data node names: "rw" means configuration (read-write) and "ro" state data (read-only). o Symbols after data node names: "?" means an optional node, "!" means a presence container, and "*" denotes a list and leaf-list. o Parentheses enclose choice and case nodes, and case nodes are also marked with a colon (":"). 2. Objectives The primary purpose of this YANG module is to enable the configuration of the NETCONF service on the device. This scope includes both transport-independent and transport-specific configuration parameters. 2.1. Support all NETCONF Transports The YANG module should support all current NETCONF transports, namely NETCONF over SSH [RFC6242] and NETCONF over TLS [I-D.ietf-netconf-rfc5539bis], and be extensible to support future transports as necessary. Since implementations may not support all transports, the module should use YANG "feature" statements so that each implementation can advertise which transports it actually supports. Watsen & Schoenwaelder Expires August 18, 2014 [Page 3] Internet-Draft YANG NETCONF Server Configuration February 2014 2.2. Align Transport-Specific Configurations While each transport is unique in its protocol and may have some distinct configurations, there remains a significant overlap between them. Thus the YANG module should use "grouping" statements so that the common aspects can be configured similarly. 2.3. Support Transport-Independent Configuration Since some NETCONF server configurations may be independent of any transport, the module should define a location for these transport- independent values to be configured. 2.4. Support both Inbound and Outbound Connections Historically, NETCONF only supported the device opening a port to listen for inbound client connections. However, the NETCONF working group is actively defining support for devices to initiate outbound connections (e.g., "call home"). Thus, the module should enable the configuration of both inbound and outbound connections. Since implementations may not support both inbound and outbound connections, the module should use YANG "feature" statements so that each implementation can advertise the type of connections it actually supports. 2.5. For Device-Initiated Outbound Connections The following objectives only pertain to support for device-initiated outbound connections. 2.5.1. Support More than One Application A device may be managed by more than one northbound applications. For instance, a deployment may have one application for provisioning and another for fault monitoring. Therefore, when it is desired for a device to initiate management connections, it should be able to do so for more than one application. 2.5.2. Support Applications Having More than One Server An application managing a device may implement a high-availability strategy employing a multiplicity of active and/or passive servers. Therefore, when it is desired for a device to initiate connections to the application, it should be able to connect to any of the applications servers. Watsen & Schoenwaelder Expires August 18, 2014 [Page 4] Internet-Draft YANG NETCONF Server Configuration February 2014 2.5.3. Support a Reconnection Strategy Assuming an application has more than one server, then it becomes necessary to understand how a device should reconnect to the application should it lose its connection to one of the application's servers. Of primary interest is if the device should start with first server defined in a user-ordered list of servers or with the last server it was connected to. Secondary settings might specify the frequency of attempts and number of attempts per server. Therefore, a reconnection strategy should be configurable. Note that the reconnection strategy should apply to both persistent and periodic connections. How it applies to periodic connections becomes clear when considering that a periodic "connection" is a logical connection to a single server. That is, the periods of unconnectedness are intentional as opposed to due to external reasons. A periodic "connection" should always reconnect to the same server until it is no longer able to, at which time the reconnection strategy guides the device how to get connected to another server. 2.5.4. Support both Persistent and Periodic Connections Applications may vary greatly on how frequently they need to interact with a device, how responsive interactions with devices need to be, and how many simultaneous connections they can support. Some applications may need a persistent connection to devices to optimize real-time interactions, while others are satisfied with periodic interactions and reduced resources required. Therefore, when it is necessary for devices to initiate connections, the type of connection desired should be configured. 2.5.5. Keep-Alives for Persistent Connections If a persistent connection is desired, it is the responsibility of the connection-initiator to actively test the connection for aliveness. However, there is a balance between the frequency of the tests and the networking overhead they generate. The appropriate balance can only be determined by the application, based on its interaction requirements. Therefore, for persistent connections, keep-alive settings should be configurable on a per-application basis. 2.5.6. Customizations for Periodic Connections If a periodic connection is desired, it is necessary for the device to know how often it should connect. This delay essentially determines how long the application might have to wait to send data to the device. Note, this setting does not constrain how often the Watsen & Schoenwaelder Expires August 18, 2014 [Page 5] Internet-Draft YANG NETCONF Server Configuration February 2014 device must wait to send data to the application, as the device should immediately connect to the application whenever it has data to send to it. A common communication pattern is that one data transmission is many times closely followed by another. For instance, if the device needs to send a notification message, there's a high probability that it will send another shortly thereafter. Likewise, the application may have a sequence of pending messages to send. Thus, it should be possible for a device to hold a connection open until some amount of time of no data being transmitted as transpired. 3. Data Model Overview 3.1. The "listen" Grouping To enable transports to configure listening on one or more ports in a common way, this grouping is defined. Being a grouping enables each transport-specific data-model to augment it as needed (e.g., to specify a default for the "port" values), as well as enable implementations to advertise support for listening for inbound connections using a YANG feature. +--rw listen +--rw (one-or-many)? +--:(one-port) | +--rw port? inet:port-number +--:(many-ports) +--rw interface* [address] +--rw address inet:ip-address +--rw port? inet:port-number 3.2. The "call-home" Grouping To enable transports to configure initiating connections to remote applications in a common way, this grouping is defined. Being a grouping enables each transport-specific data-model to augment it as needed (e.g., to specify a default port value, lists of algorithms to advertise, etc.), as well as enable implementations to advertise support for listening for inbound connections using a YANG feature. +--rw call-home +--rw applications +--rw application* [name] +--rw name string +--rw description? string +--rw servers | +--rw server* [address] Watsen & Schoenwaelder Expires August 18, 2014 [Page 6] Internet-Draft YANG NETCONF Server Configuration February 2014 | +--rw address inet:host | +--rw port? inet:port-number +--rw connection-type | +--rw (connection-type)? | +--:(persistent-connection) | | +--rw persistent | | +--rw keep-alives | | +--rw interval-secs? uint8 | | +--rw count-max? uint8 | +--:(periodic-connection) | +--rw periodic | +--rw timeout-mins? uint8 | +--rw linger-secs? uint8 +--rw reconnect-strategy +--rw start-with? enumeration +--rw interval-secs? uint8 +--rw count-max? uint8 3.3. The SSH Subtree The SSH subtree uses both the "listen" and "call-home" groupings mentioned above. Support for the SSH transport is advertised by the "ssh" feature, while listening for clients and calling home are advertised by the "inbound-ssh" and "outbound-ssh" features respectively. The SSH subtree augments the "call-home" grouping by adding a "host-keys" container. Also, though not visible in the tree output below, this subtree refines all the port values with a suitable default (i.e., 830). +--rw netconf +--rw ssh {ssh}? +--rw listen {inbound-ssh}? | +--rw (one-or-many)? | +--:(one-port) | | +--rw port? inet:port-number | +--:(many-ports) | +--rw interface* [address] | +--rw address inet:ip-address | +--rw port? inet:port-number +--rw call-home {outbound-ssh}? +--rw applications +--rw application* [name] +--rw name string +--rw description? string +--rw servers | +--rw server* [address] | +--rw address inet:host | +--rw port? inet:port-number Watsen & Schoenwaelder Expires August 18, 2014 [Page 7] Internet-Draft YANG NETCONF Server Configuration February 2014 +--rw connection-type | +--rw (connection-type)? | +--:(persistent-connection) | | +--rw persistent | | +--rw keep-alives | | +--rw interval-secs? uint8 | | +--rw count-max? uint8 | +--:(periodic-connection) | +--rw periodic | +--rw timeout-mins? uint8 | +--rw linger-secs? uint8 +--rw reconnect-strategy | +--rw start-with? enumeration | +--rw interval-secs? uint8 | +--rw count-max? uint8 +--rw host-keys +--rw host-key* [name] +--rw name string 3.4. The TLS Subtree The TLS subtree uses both the "listen" and "call-home" groupings mentioned above, while also defining containers for certificate and pre-shared key mappings. Support for the TLS transport is advertised by the "tls" feature, while listening for clients and calling home are advertised by the "inbound-tls" and "outbound-tls" features respectively. Also, though not visible in the tree output below, this submodule refines all the port values with a suitable defaults (e.g., 6513). +--rw netconf +--rw tls {tls}? +--rw listen {inbound-tls}? | +--rw (one-or-many)? | +--:(one-port) | | +--rw port? inet:port-number | +--:(many-ports) | +--rw interface* [address] | +--rw address inet:ip-address | +--rw port? inet:port-number +--rw call-home {outbound-tls}? | +--rw applications | +--rw application* [name] | +--rw name string | +--rw description? string | +--rw servers | | +--rw server* [address] | | +--rw address inet:host Watsen & Schoenwaelder Expires August 18, 2014 [Page 8] Internet-Draft YANG NETCONF Server Configuration February 2014 | | +--rw port? inet:port-number | +--rw connection-type | | +--rw (connection-type)? | | +--:(persistent-connection) | | | +--rw persistent | | | +--rw keep-alives | | | +--rw interval-secs? uint8 | | | +--rw count-max? uint8 | | +--:(periodic-connection) | | +--rw periodic | | +--rw timeout-mins? uint8 | | +--rw linger-secs? uint8 | +--rw reconnect-strategy | +--rw start-with? enumeration | +--rw interval-secs? uint8 | +--rw count-max? uint8 +--rw cert-maps {tls-map-certificates}? | +--rw cert-to-name* [id] | +--rw id uint32 | +--rw fingerprint x509c2n:tls-fingerprint | +--rw map-type identityref | +--rw name string +--rw psk-maps {tls-map-pre-shared-keys}? +--rw psk-map* [psk-identity] +--rw psk-identity string +--rw user-name nacm:user-name-type +--rw not-valid-before? yang:date-and-time +--rw not-valid-after? yang:date-and-time +--rw key yang:hex-string 4. NETCONF Server YANG Module This YANG module imports YANG extensions from [RFC6536], and imports YANG types from [RFC6991] and a YANG grouping from [I-D.ietf-netmod-snmp-cfg]. module ietf-netconf-server { namespace "urn:ietf:params:xml:ns:yang:ietf-netconf-server"; prefix "ncserver"; import ietf-yang-types { prefix yang; // RFC 6991 } import ietf-inet-types { prefix inet; // RFC 6991 } import ietf-x509-cert-to-name { Watsen & Schoenwaelder Expires August 18, 2014 [Page 9] Internet-Draft YANG NETCONF Server Configuration February 2014 prefix x509c2n; // I-D.ietf-netconf-rfc5539bis } import ietf-netconf-acm { prefix nacm; // RFC 6536 } organization "IETF NETCONF (Network Configuration) Working Group"; contact "WG Web: WG List: WG Chair: Mehmet Ersue WG Chair: Bert Wijnen Editor: Juergen Schoenwaelder Kent Watsen "; description "This module contains a collection of YANG definitions for configuring NETCONF servers. Copyright (c) 2014 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This version of this YANG module is part of RFC XXXX; see the RFC itself for full legal notices."; // RFC Ed.: replace XXXX with actual RFC number and // remove this note // RFC Ed.: please update the date to the date of publication revision "2014-01-24" { description Watsen & Schoenwaelder Expires August 18, 2014 [Page 10] Internet-Draft YANG NETCONF Server Configuration February 2014 "Initial version"; reference "RFC XXXX: A YANG Data Model for NETCONF Server Configuration"; } /* * Features */ feature ssh { description "A server implements this feature if it supports NETCONF over Secure Shell (SSH)."; reference "RFC 6242: Using the NETCONF Protocol over Secure Shell (SSH)"; } feature inbound-ssh { description "The inbound-ssh feature indicates that the server can open a port to listen for incoming client connections."; } feature outbound-ssh { description "The outbound-ssh feature indicates that the server can connect to a client."; reference "RFC XXXX: Reverse Secure Shell (Reverse SSH)"; } feature tls { description "A server implements this feature if it supports NETCONF over Transport Layer Security (TLS)."; reference "RFC XXXX: NETCONF over Transport Layer Security (TLS)"; } feature inbound-tls { description "The inbound-tls feature indicates that the server can open a port to listen for incoming client connections."; } feature outbound-tls { description "The outbound-tls feature indicates that the server can Watsen & Schoenwaelder Expires August 18, 2014 [Page 11] Internet-Draft YANG NETCONF Server Configuration February 2014 connect to a client."; } feature tls-map-certificates { description "The tls-map-certificates feature indicates that the server implements mapping X.509 certificates to NETCONF usernames."; } feature tls-map-pre-shared-keys { description "The tls-map-pre-shared-keys feature indicates that the server implements mapping TLS pre-shared keys to NETCONF usernames."; } /* * Groupings */ grouping listen-config { description "Provides a choice of configuring one of more ports to listen for incoming client connections."; choice one-or-many { default one-port; case one-port { leaf port { type inet:port-number; description "The port number the server listens on on all interfaces."; } } case many-ports { list interface { key "address"; leaf address { type inet:ip-address; mandatory true; description "The local IP address of the interface to listen on."; } leaf port { Watsen & Schoenwaelder Expires August 18, 2014 [Page 12] Internet-Draft YANG NETCONF Server Configuration February 2014 type inet:port-number; description "The local port number on this interface the server listens on."; } } } } } grouping call-home-config { container applications { description "A list of applications the device iniates connections to. The configuration for each application specifies its details, including its servers, the type of connection to maintain, and the reconnection strategy to use."; list application { key name; // min-elements 1; // this forces ?! leaf name { type string { length 1..64; // XXX why these limits? } mandatory true; description "An arbitrary name for the application the device is connecting to."; } leaf description { type string; description "An optional description for the application."; } container servers { description "An ordered listing of the application's servers that the device should attempt connecting to."; list server { key address; min-elements 1; ordered-by user; leaf address { type inet:host; mandatory true; Watsen & Schoenwaelder Expires August 18, 2014 [Page 13] Internet-Draft YANG NETCONF Server Configuration February 2014 description "The address or domain-name of the server."; } leaf port { type inet:port-number; description "The IP port for this server. The device will use the IANA-assigned well-known port if not specified."; } } } container connection-type { description "Indicates the application's preference for how the device's connection is maintained."; choice connection-type { default persistent-connection; case persistent-connection { container persistent { description "Maintain a persistent connection to the application. If the connection goes down, immediately start trying to reconnect to it, using the reconnection strategy. This connection type minimizes any application-to-server data-transfer delay, albeit at the expense of holding resources longer."; container keep-alives { leaf interval-secs { type uint8; units seconds; default 15; description "Sets a timeout interval in seconds after which if no data has been received from the application, a message will be sent to request a response from the application. A value of '0' indicates that no keep-alive messages should be sent."; } leaf count-max { type uint8; default 3; description "Sets the number of keep-alive messages that may Watsen & Schoenwaelder Expires August 18, 2014 [Page 14] Internet-Draft YANG NETCONF Server Configuration February 2014 be sent without receiving any data from the application before assuming the application is no longer alive. If this threshold is reached, the transport-level connection will be disconnected (thus triggering the reconnection strategy). The interval timer is reset after each transmission, thus an unresponsive application will be disconnected after approximately count-max * interval-secs seconds."; } } } } case periodic-connection { container periodic { description "Periodically connect to application, using the reconnection strategy, so it can flush any pending data it may be holding. This connection type minimizes resources held open, albeit at the expense of longer application-to-server data-transfer delay. Note that for server-to-application data, the data should be sent immediately, connecting to application first if not already."; leaf timeout-mins { type uint8; units minutes; default 5; description "The maximum amount of unconnected time the device will wait until establishing a connection to the application again. The device may establish a connection before this time if it has data it needs to send to the application. Note: this value differs from the reconnection strategy's interval-secs value."; } leaf linger-secs { type uint8; units seconds; default 30; description "The amount of time the device should wait after last receiving data from or sending data to the Watsen & Schoenwaelder Expires August 18, 2014 [Page 15] Internet-Draft YANG NETCONF Server Configuration February 2014 application before closing its connection to it. This is an optimization to prevent unnecessary connections."; } } } } } // XXX // Should we have something smarter as the reconnect // strategy, e.g. an exponential backoff? container reconnect-strategy { description "The reconnection strategy guides how a device reconnects to an application, after losing a connection to it, even if due to a reboot. The device starts with the specified server, tries to connect to it count-max times, waiting interval-secs between each connection attempt, before trying the next server in the list (round robin)."; leaf start-with { type enumeration { enum first-listed { value 1; } enum last-connected { value 2; } } default first-listed; description "Specifies which of the application's servers the device should start with when trying to connect to the application. In the case of newly configured application, the first server listed shall be considered last-connected."; } leaf interval-secs { type uint8; units seconds; default 5; description "Specifies the time delay between connection attempts to the same server. Note: this value differs from the periodic-connection's timeout-mins value."; } leaf count-max { type uint8; default 3; description "Specifies the number times the device tries to Watsen & Schoenwaelder Expires August 18, 2014 [Page 16] Internet-Draft YANG NETCONF Server Configuration February 2014 connect to a specific server before moving on to the next server in the list (round robin)."; } } } } } grouping ssh-config { description "Provides a reusable grouping for all the ssh config. This is done primarily to enable external modules to reference this definition in a "uses" statement."; container listen { if-feature inbound-ssh; description "Provides the configuration of the NETCONF server to open one or more ports to listen for incoming client connections."; uses listen-config { refine one-or-many/one-port/port { default 830; } refine one-or-many/many-ports/interface/port { default 830; } } } container call-home { if-feature outbound-ssh; description "Provides the configuration of the NETCONF call-home clients to connect to, the overall call-home policy, and the reconnect strategy."; uses call-home-config { augment applications/application { container host-keys { description "An ordered listing of the SSH host keys the device should advertise to the application."; list host-key { key name; min-elements 1; ordered-by user; leaf name { Watsen & Schoenwaelder Expires August 18, 2014 [Page 17] Internet-Draft YANG NETCONF Server Configuration February 2014 type string { length 1..64; // XXX why this limit? } mandatory true; description "The name of a host key the device should advertise during the SSH key exchange."; } } } } } } } grouping tls-config { description "Provides a reusable grouping for all the tls config. This is done primarily to enable external modules to reference this definition in a "uses" statement."; container listen { if-feature inbound-tls; description "Provides the configuration of the NETCONF server to open one or more ports to listen for incoming client connections."; uses listen-config { refine one-or-many/one-port/port { default 6513; } refine one-or-many/many-ports/interface/port { default 6513; } } } container call-home { if-feature outbound-tls; description "Provides the configuration of the NETCONF call-home clients to connect to, the overall call-home policy, and the reconnect strategy."; uses call-home-config; } /* * Objects for deriving NETCONF usernames from X.509 Watsen & Schoenwaelder Expires August 18, 2014 [Page 18] Internet-Draft YANG NETCONF Server Configuration February 2014 * certificates. */ container cert-maps { if-feature tls-map-certificates; uses x509c2n:cert-to-name; description "The cert-maps container is used by a NETCONF server to map the NETCONF client's presented X.509 certificate to a NETCONF username. If no matching and valid cert-to-name list entry can be found, then the NETCONF server MUST close the connection, and MUST NOT accept NETCONF messages over it."; } /* * Objects for deriving NETCONF usernames from TLS * pre-shared keys. */ container psk-maps { if-feature tls-map-pre-shared-keys; description "During the TLS Handshake, the client indicates which key to use by including a PSK identity in the TLS ClientKeyExchange message. On the server side, this PSK identity is used to look up an entry in the psk-map list. If such an entry is found, and the pre-shared keys match, then the client is authenticated. The server uses the value from the user-name leaf in the psk-map list as the NETCONF username. If the server cannot find an entry in the psk-map list, or if the pre-shared keys do not match, then the server terminates the connection."; reference "RFC 4279: Pre-Shared Key Ciphersuites for Transport Layer Security (TLS)"; list psk-map { key psk-identity; leaf psk-identity { type string; description "The PSK identity encoded as a UTF-8 string. For details how certain common PSK identity formats can be encoded in UTF-8, see section 5.1. of RFC 4279."; reference Watsen & Schoenwaelder Expires August 18, 2014 [Page 19] Internet-Draft YANG NETCONF Server Configuration February 2014 "RFC 4279: Pre-Shared Key Ciphersuites for Transport Layer Security (TLS)"; } leaf user-name { type nacm:user-name-type; mandatory true; description "The NETCONF username associated with this PSK identity."; } leaf not-valid-before { type yang:date-and-time; description "This PSK identity is not valid before the given date and time."; } leaf not-valid-after { type yang:date-and-time; description "This PSK identity is not valid after the given date and time."; } leaf key { type yang:hex-string; mandatory true; nacm:default-deny-all; description "The key associated with the PSK identity"; reference "RFC 4279: Pre-Shared Key Ciphersuites for Transport Layer Security (TLS)"; } } } } /* * Configuration data nodes */ container netconf { description "Top-level container for NETCONF server related configuration objects."; container ssh { if-feature ssh; Watsen & Schoenwaelder Expires August 18, 2014 [Page 20] Internet-Draft YANG NETCONF Server Configuration February 2014 uses ssh-config; } container tls { if-feature tls; uses tls-config; } } } 5. Security Considerations This document defines a YANG modules to configure NETCONF's SSH and TLS transports. Please see the Security Considerations section in those RFCs for transport-specific issues. 6. IANA Considerations This document registers one URIs in the IETF XML registry [RFC2119]. Following the format in [RFC3688], the following registration is requested to be made. URI: urn:ietf:params:xml:ns:yang:ietf-netconf-server Registrant Contact: The NETCONF WG of the IETF. XML: N/A, the requested URI is an XML namespace. This document registers one YANG module in the YANG Module Names registry [RFC6020]. name: ietf-netconf-server namespace: urn:ietf:params:xml:ns:yang:ietf-netconf-server prefix: ncserver reference: RFC XXXX 7. Acknowledgements Juergen Schoenwaelder and was partly funded by Flamingo, a Network of Excellence project (ICT-318488) supported by the European Commission under its Seventh Framework Programme. 8. References Watsen & Schoenwaelder Expires August 18, 2014 [Page 21] Internet-Draft YANG NETCONF Server Configuration February 2014 8.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels ", BCP 14, RFC 2119, March 1997. [RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF) ", RFC 6020, October 2010. [RFC6536] Bierman, A. and M. Bjorklund, "Network Configuration Protocol (NETCONF) Access Control Model ", RFC 6536, March 2012. [RFC6991] Schoenwaelder, J., "Common YANG Data Types", RFC 6991, July 2013. [I-D.ietf-netmod-snmp-cfg] Bjorklund, M. and J. Schoenwaelder, "A YANG Data Model for SNMP Configuration", draft-ietf-netmod-snmp-cfg-03 (work in progress), November 2013. [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "NETCONF Configuration Protocol", RFC 6241, June 2011. [RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, June 2011. [I-D.ietf-netconf-rfc5539bis] Badra, M., Luchuk, A., and J. Schoenwaelder, "Using the NETCONF Protocol over Transport Layer Security (TLS) ", draft-ietf-netconf-rfc5539bis-04 (work in progress), October 2013. 8.2. Informative References [RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, January 2004. Appendix A. Example: SSH 831 Watsen & Schoenwaelder Expires August 18, 2014 [Page 22] Internet-Draft YANG NETCONF Server Configuration February 2014 config-mgr This entry requests the device to periodically connect to the Configuration Manager application
config-mgr1.example.com
config-mgr2.example.com
 5 10 last-connected 10 3 ssh_host_key_cert ssh_host_key_cert2 Appendix B. Example: TLS Watsen & Schoenwaelder Expires August 18, 2014 [Page 23] Internet-Draft YANG NETCONF Server Configuration February 2014
192.0.2.1
6514 log-monitor This entry requests the device to maintain a persistent connect to the Log Monitor application
log-monitor1.example.com
log-monitor2.example.com
 5 3 first-listed 10 4 1 11:0A:05:11:00 x509c2n:san-any 2 11:0A:05:11:00 x509c2n:specified Joe Cool a8gc8]klh59 admin 2013-01-01T00:00:00Z 2014-01-01T00:00:00Z Appendix C. Change Log C.1. 00 to 01 o Restructured YANG module slightly, to provide groupings useful to the ZeroTouch draft. Appendix D. Open Issues o NETCONF implementations typically have config parameters such as session timeouts or hello timeouts. Shall they be included in this model? o Do we need knobs to enable/disable call-home without the need to remove all the call-home client configuration? o Do we need something equivalent to the host-keys in the TLS configuration subtree? Authors' Addresses Kent Watsen Juniper Networks EMail: kwatsen@juniper.net Watsen & Schoenwaelder Expires August 18, 2014 [Page 25] Internet-Draft YANG NETCONF Server Configuration February 2014 Juergen Schoenwaelder Jacobs University Bremen EMail: j.schoenwaelder@jacobs-university.de Watsen & Schoenwaelder Expires August 18, 2014 [Page 26]